Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Kolsky Bar”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

6 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

A Method for Dynamic Kolsky Bar Compression at High Temperatures: Application to Ti-6Al-4V

Abstract An experimental apparatus for measuring the dynamic behavior of materials subjected to strain rates on the order of 10 $$^3$$ 3 s $$^{-1}$$ - 1 and temperatures up to 800°C with a unique triple actuation system is developed in this work. This system is based on the traditional Kolsky (or split-Hopkinson pressure) bar design, with the addition of an external furnace used to heat the specimen to the desired temperature. A synchronized triple pneumatic actuation system is used to control the motion and timing of the the sample, incident, and transmitted bars. The cold contact time (CCT), or the time during which the heated sample is in contact with the room temperature bars before compression, is measured experimentally and carefully controlled to minimize the development of a temperature gradient across the sample and avoid heating of the bars. Experiments are performed in conjunction with ultra high speed imaging and 2D digital image correlation (DIC), as well as high speed thermal imaging. To verify the viability of the proposed system, experiments were conducted on Ti-6Al-4V (wt.%) at temperatures from 25°C up to and 800°C at an average strain rate of approximately 1200 s $$^{-1}$$ - 1 .

36 MATERIALS SCIENCE↗
DOE OSTI2025

Rapid tempering to enhance dynamic performance of high and ultra-high strength steels

This study employed rapid, short-time duration (1 s) tempering to improve the dynamic performance of high-strength steel (HSS) and ultra-high-strength steel (UHSS), compared to quenched and conventionally (1800 s) tempered microstructures. Rapid tempering significantly improved the Charpy toughness of both steels compared to the conventionally tempered condition at an equivalent tempering parameter (TP) or hardness level. For conventionally tempered conditions, tempered martensite embrittlement was observed within the tempering temperature range of 200–400 °C, whereas rapid tempering exhibited increased Charpy toughness with increasing tempering temperature across all tempering conditions. Dynamic compression experiments indicated that rapid tempering led to improved ductility compared to the conventionally tempered condition at an equivalent TP. This work shows that the same rapid tempering strategy used for HSS is directly transferable to a higher-carbon UHSS and provides the first systematic evidence of improved strength-ductility combinations and cracking resistance under dynamic compression, supported by Kolsky bar experiments.

36 MATERIALS SCIENCE↗
DOE OSTI2025

An Integrated High-Speed Microstructural Characterization Method Using Simultaneous XRD, Stereo-DIC, and PCI

High-speed characterization of the deformation mechanisms in polycrystalline metals requires the quantification of full strain fields and local microstructural evolutions simultaneously. In this paper, we present a novel experimental method to integrate phase-contrast imaging (PCI), stereographic digital image correlation (stereo-DIC), and full-ring X-ray diffraction (XRD) to allow for the simultaneous characterization of polycrystalline metals at 1MHz or higher. A Kolsky bar was integrated into the synchrotron X-ray source in Sector 32 ID-B at the Advance Photon Source (APS) at Argonne National Laboratory. When the sample is dynamically loaded, the diagnostic methods of full-ring XRD, PCI, and stereo-DIC are properly synchronized to record the deformation behavior at both continuum and microstructural scales as a function of the loading history. An advanced high-strength steel (AHSS) is used as a model material to demonstrate the capabilities of this new experimental method.

36 MATERIALS SCIENCE↗
DOE OSTI2025

An Internal Digital Image Correlation Technique for High-Strain Rate Dynamic Experiments

Full-field, quantitative visualization techniques, such as digital image correlation (DIC), have unlocked vast opportunities for experimental mechanics. However, DIC has traditionally been a surface measurement technique, and has not been extended to perform measurements on the interior of specimens for dynamic, full-scale laboratory experiments. This limitation restricts the scope of physics which can be investigated through DIC measurements, especially in the context of heterogeneous materials. The focus of this study is to develop a method for performing internal DIC measurements in dynamic experiments. The aim is to demonstrate its feasibility and accuracy across a range of stresses (up to 650 MPa), strain rates (10 3 - 10 6 s -1 ), and high-strain rate loading conditions (e.g., ramped and shock wave loading). Internal DIC is developed based on the concept of applying a speckle pattern at an inner-plane of a transparent specimen. The high-speed imaging configuration is coupled to the traditional dynamic experimental setups, and is focused on the internal speckle pattern. During the experiment, while the sample deforms dynamically, in-plane, two-dimensional deformations are measured via correlation of the internal speckle pattern. In this study, the viability and accuracy of the internal DIC technique is demonstrated for split-Hopkinson (Kolsky) pressure bar (SHPB) and plate impact experiments. The internal DIC experimental technique is successfully demonstrated in both the SHPB and plate impact experiments. In the SHPB setting, the accuracy of the technique is excellent throughout the deformation regime, with measurement noise of approximately 0.2% strain. In the case of plate impact experiments, the technique performs well, with error and measurement noise of 1% strain. The internal DIC technique has been developed and demonstrated to work well for full-scale dynamic high-strain rate and shock laboratory experiments, and the accuracy is quantified. Here, the technique can aid in investigating the physics and mechanics of the dynamic behavior of materials, including local deformation fields around dynamically loaded material heterogeneities.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Phase-field modeling and experiments of dynamic fracture in single crystal quartz

Predicting the onset and characteristics of brittle fracture is important for a wide range of engineering and geological material applications. In this paper, we study important aspects of brittle fracture in α-quartz by phase-field modeling and experiments using a top-down approach. In the modeling framework, the work term in the Griffith energy balance is replaced with internal energy contributions that represent surface energy, thermal energy, and elastic strain energy stored in defects. This allows parametrization of individual energy contributions in terms of internal state variables and keeps track of energy partitioning after the onset of fracture. The path and history dependence of fracture is included in evolution laws for internal state variables, e.g., entropy evolution, while the energy remains a true potential. In the experimental part, dynamic compression experiments coupled with X-ray phase contrast imaging are performed on cube-like samples with a hole. In the top-down analysis, dynamic compression and three point bending experiments from the literature are simulated with the developed phase-field damage model. In conclusion, the fitted model highlights the strain rate, size, and stress state dependence of damage nucleation and evolution in single crystal α-quartz.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Quasi-static to Dynamic Mechanical Response and Microstructure Development of Tantalum-Tungsten Alloys

Lawrence Livermore National Laboratory (LLNL) is interested the quasi-static to dynamic mechanical response and microstructure evolution of tantalum-tungsten (Ta-W) alloys (Ta-2.5W, Ta-5W, and Ta-10W, wt.%) made by conventional wrought processing and additive manufacturing (AM). This work scope was performed at the Colorado School of Mines (Mines) and included quasi-static (e.g., 10 -3 s -1 ) mechanical testing in tension and compression, along with selected high strain rate (Kolsky) pressure bar testing in compression (e.g., 10 3 s -1 ), with and without temperature variations in some instances. Complementary microstructure characterization was performed on undeformed and deformed samples to understand the role of processing on microstructural evolution and the deformation mechanisms that impact the mechanical response with variations in strain rate, temperature, and strain state (e.g., tension versus compression in selected examples). The wrought material provided by LLNL from Viridis Materials was found to have unrecrystallized regions within the microstructure, which led to unexpected results relative to previously reported properties for Ta-W. The AM Ta-2.5W (wt.%) material provided by LLNL was found to have higher compressive strength than wrought Ta-2.5W (wt.%), which is hypothesized to be due to differences in the crystallographic texture between the two materials. This project partially supported several postdocs and graduate students at Mines.

36 MATERIALS SCIENCE↗