Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Knot optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2015

Flow Separation Control on A Full-Scale Vertical Tail Model Using Sweeping Jet Actuators

This paper describes test results of a joint NASA/Boeing research effort to advance Active Flow Control (AFC) technology to enhance aerodynamic efficiency. A full-scale Boeing 757 vertical tail model equipped with sweeping jets AFC was tested at the National Full-Scale Aerodynamics Complex 40- by 80-Foot Wind Tunnel at NASA Ames Research Center. The flow separation control optimization was performed at 100 knots, a maximum rudder deflection of 30deg, and sideslip angles of 0deg and -7.5deg. Greater than 20% increments in side force were achieved at the two sideslip angles with a 31-actuator AFC configuration. Flow physics and flow separation control associated with the AFC are presented in detail. AFC caused significant increases in suction pressure on the actuator side and associated side force enhancement. The momentum coefficient (C sub mu) is shown to be a useful parameter to use for scaling-up sweeping jet AFC from sub-scale tests to full-scale applications. Reducing the number of actuators at a constant total C(sub mu) of approximately 0.5% and tripling the actuator spacing did not significantly affect the flow separation control effectiveness.

Andino, Marlyn Y.↗
NASA NTRS1983

Minimum-fuel turning climbout and descent guidance of transport jets

The complete flightpath optimization problem for minimum fuel consumption from takeoff to landing including the initial and final turns from and to the runway heading is solved. However, only the initial and final segments which contain the turns are treated, since the straight-line climbout, cruise, and descent problems have already been solved. The paths are derived by generating fields of extremals, using the necessary conditions of optimal control together with singular arcs and state constraints. Results show that the speed profiles for straight flight and turning flight are essentially identical except for the final horizontal accelerating or decelerating turns. The optimal turns require no abrupt maneuvers, and an approximation of the optimal turns could be easily integrated with present straight-line climb-cruise-descent fuel-optimization algorithms. Climbout at the optimal IAS rather than the 250-knot terminal-area speed limit would save 36 lb of fuel for the 727-100 aircraft.

Neuman, F.↗
NASA NTRS1975

Optimal control alleviation of tilting proprotor gust response

Optimal control theory is applied to the design of a control system for alleviation of the gust response of tilting proprotor aircraft. Using a proprotor and cantilever wing analytical model, the uncontrolled and controlled gust response is examined over the entire operating range of the aircraft except for hover: helicopter mode, conversion, and airplane mode flight. Substantial improvements in the loads, ride quality, and aeroelastic stability are possible with a properly designed controller. A single controller, nominally optimal only at the design point speed (160 knots here), operated efficiently over the entire speed range, with the possible exception of very low speed in helicopter mode. Kalman-Bucy filters were used as compensation networks to provide state estimates from various measurements in the wing motion, rotor speed perturbation, and tip-path-plane tilt.

Johnson, W.↗
NASA NTRS1977

Optimal control alleviation of tilting proprotor gust response

Optimal control theory is applied to the design of a control system for alleviation of the gust response of tilting proprotor aircraft. Using a proprotor and cantilever wing analytical model, the uncontrolled and controlled gust response is examined over the entire operating range of the aircraft except for hover: helicopter mode, conversion, and airplane mode flight. Substantial improvements in the loads, ride quality, and aeroelastic stability are possible with a properly designed controller. A single controller, nominally optimal only at the design point speed (160 knots here), operated efficiently over the entire speed range, with the possible exception of very low speed in helicopter mode. Kalman-Bucy filters were used as compensation networks to provide state estimates from various measurements in the system. Efficient control requires the measurement of the wing motion, rotor speed perturbation, and tip-path-plane tilt.

Johnson, W.↗
NASA NTRS2006

Impact of Airfoils on Aerodynamic Optimization of Heavy Lift Rotorcraft

Rotor airfoils were developed for two large tiltrotor designs, the Large Civil Tilt Rotor (LCTR) and the Military Heavy Tilt Rotor (MHTR). The LCTR was the most promising of several rotorcraft concepts produced by the NASA Heavy Lift Rotorcraft Systems Investigation. It was designed to carry 120 passengers for 1200 nm, with performance of 350 knots cruise at 30,000 ft altitude. A parallel design, the MHTR, had a notional mission of 40,000 Ib payload, 500 nm range, and 300 knots cruise at 4000 ft, 95 F. Both aircraft were sized by the RC code developed by the U. S. Army Aeroflightdynamics Directorate (AFDD). The rotors were then optimized using the CAMRAD II comprehensive analysis code. Rotor airfoils were designed for each aircraft, and their effects on performance analyzed by CAMRAD II. Airfoil design criteria are discussed for each rotor. Twist and taper optimization are presented in detail for each rotor, with discussions of performance improvements provided by the new airfoils, compared to current technology airfoils. Effects of stall delay and blade flexibility on performance are also included.

Acree, Cecil W., Jr.↗
NASA NTRS1993

Design optimization of high-speed proprotor aircraft

NASA's high-speed rotorcraft (HSRC) studies have the objective of investigating technology for vehicles that have both low downwash velocities and forward flight speed capability of up to 450 knots. This paper investigates a tilt rotor, a tilt wing, and a folding tilt rotor designed for a civil transport mission. Baseline aircraft models using current technology are developed for each configuration using a vertical/short takeoff and landing (V/STOL) aircraft design synthesis computer program to generate converged vehicle designs. Sensitivity studies and numerical optimization are used to illustrate each configuration's key design tradeoffs and constraints. Minimization of the gross takeoff weight is used as the optimization objective function. Several advanced technologies are chosen, and their relative impact on future configurational development is discussed. Finally, the impact of maximum cruise speed on vehicle figures of merit (gross weight, productivity, and direct operating cost) is analyzed. The three most important conclusions from the study are payload ratios for these aircraft will be commensurate with current fixed-wing commuter aircraft; future tilt rotors and tilt wings will be significantly lighter, more productive, and cheaper than competing folding tilt rotors; and the most promising technologies are an advanced-technology proprotor for both tilt rotor and tilt wing and advanced structural materials for the folding tilt rotor.

Schleicher, David R.↗
NASA NTRS1980

Aerodynamic design optimization of a fuel efficient high-performance, single-engine, business airplane

A design study has been conducted to optimize a single-engine airplane for a high-performance cruise mission. The mission analyzed included a cruise speed of about 300 knots, a cruise range of about 1300 nautical miles, and a six-passenger payload (5340 N (1200 lb)). The purpose of the study is to investigate the combinations of wing design, engine, and operating altitude required for the mission. The results show that these mission performance characteristics can be achieved with fuel efficiencies competitive with present-day high-performance, single- and twin-engine, business airplanes. It is noted that relaxation of the present Federal Aviation Regulation, Part 23, stall-speed requirement for single-engine airplanes facilitates the optimization of the airplane for fuel efficiency.

Holmes, B. J.↗
NASA NTRS2018

Full-Scale Testing of Active Flow Control Enhanced Vertical Tail

This paper describes wind tunnel test results from a joint NASA/Boeing research effort to advance active flow control (AFC) technology to enhance aerodynamic efficiency. A full-scale Boeing 757 vertical tail model equipped with 37 sweeping jet actuators was tested at the National Full-Scale Aerodynamics Complex (NFAC) 40- by 80-Foot Wind Tunnel (40x80) at NASA Ames Research Center. The model was tested at a nominal airspeed of 100 knots and across rudder deflections and sideslip angles that covered the vertical tail flight envelope. The flow separation control optimization was performed at the maximum rudder deflection of 30° and sideslip angles of 0° and -7.5°. Greater than 20% increase in side force were achieved at maximum rudder deflection and the two sideslip angles with a 31-actuator configuration. AFC caused significant increases in suction pressure on the actuator side and associated side force enhancement. The successful demonstration of this application cleared the way for a subsequent flight demonstration on the Boeing 757 ecoDemonstrator in 2015.

Whalen, Edward A.↗
NASA NTRS1973

Estimation of peak winds from hourly observations

Two closely related methods to obtain estimates of the hourly peak wind at Cape Kennedy were compared by statistical tests. The methods evaluated the Monin-Obukhov stability length and the standard deviation of the hourly observed wind speed, so as to augment the latter quantity by F standard deviations. F is an optimized factor. A third method utilizing an optimized gust factor was also applied to the hourly wind. The latter procedure estimated 2952 peak winds with an rms error of 2.81 knots, an accuracy which was not surpassed by the other methods. Peak ground wind speed data were developed for use in space shuttle design operation analyses.

Graves, M. E.↗
NASA NTRS1985

Design study of technology requirements for high performance single-propeller-driven business airplanes

Developments in aerodyamic, structural and propulsion technologies which influence the potential for significant improvements in performance and fuel efficiency of general aviation business airplanes are discussed. The advancements include such technolgies as natural laminar flow, composite materials, and advanced intermittent combustion engines. The design goal for this parameter design study is a range of 1300 nm at 300 knots true airspeed with a payload of 1200lbs at 35,000 ft cruise altitude. The individual and synergistic effects of various advanced technologies on the optimization of this class of high performance, single engine, propeller driven business airplanes are identified.

Kohlman, D. L.↗
NASA NTRS2007

Performance of Advanced Heavy-Lift, High-Speed Rotorcraft Configurations

The aerodynamic performance of rotorcraft designed for heavy-lift and high-speed cruise is examined. Configurations considered include the tiltrotor, the compound helicopter, and the lift-offset rotor. Design conditions are hover and 250-350 knot cruise, at 5k/ISA+20oC (civil) or 4k/95oF (military); with cruise conditions at 4000 or 30,000 ft. The performance was calculated using the comprehensive analysis CAMRAD II, emphasizing rotor optimization and performance, including wing-rotor interference. Aircraft performance was calculated using estimates of the aircraft drag and auxiliary propulsion efficiency. The performance metric is total power, in terms of equivalent aircraft lift-to-drag ratio L/D = WV/P for cruise, and figure of merit for hover.

Johnson, Wayne↗
NASA NTRS2006

Impact of Aerodynamics and Structures Technology on Heavy Lift Tiltrotors

Rotor performance and aeroelastic stability are presented for a 124,000-lb Large Civil Tilt Rotor (LCTR) design. It was designed to carry 120 passengers for 1200 nm, with performance of 350 knots at 30,000 ft altitude. Design features include a low-mounted wing and hingeless rotors, with a very low cruise tip speed of 350 ft/sec. The rotor and wing design processes are described, including rotor optimization methods and wing/rotor aeroelastic stability analyses. New rotor airfoils were designed specifically for the LCTR; the resulting performance improvements are compared to current technology airfoils. Twist, taper and precone optimization are presented, along with the effects of blade flexibility on performance. A new wing airfoil was designed and a composite structure was developed to meet the wing load requirements for certification. Predictions of aeroelastic stability are presented for the optimized rotor and wing, along with summaries of the effects of rotor design parameters on stability.

Acree, C. W., Jr.↗
NASA NTRS1987

Calculated performance, stability, and maneuverability of high speed tilting proprotor aircraft

The feasibility of operating tilting proprotor aircraft at high speeds is examined by calculating the performance, stability, and maneuverability of representative configurations. The rotor performance is examined in high speed cruise and in hover. The whirl flutter stability of the coupled wing and rotor motion is calculated in cruise. Maneuverability is examined in terms of the rotor thrust limit during turns in helicopter configuration. Rotor airfoils, rotor hub configuration, wing airfoil, and airframe structural weights representative of demonstrated advanced technology are considered. Key rotor and airframe parameters are optimized for high speed performance and stability. The basic aircraft design parameters are optimized for minimum gross weight. To provide a focus for the calculations, two high speed tiltrotor aircraft are considered: a 46-passenger civil transport and an air-combat/escort fighter, both with design speeds of about 400 knots. It is concluded that such high speed tiltrotor aircraft are quite practical.

Johnson, Wayne↗
NASA NTRS1985

The Construction of Curves and Surfaces Using Numerical Optimization Techniques

Numerical optimization techniques are playing an increasing role in curve and surface construction. Often difficult problems in curve and surface construction, especially when some aspect of shape control is involved, can be phrased as a constrained optimization problem. Four such classes of problems are explored: parametric curve fitting with non-linear shape constraints; explicit surface fitting with linear shape constraints; surface fitting to scattered data giving rise to ill-posed problems; finally, variable knot problems. In each of these problems there is a nonlinear aspect: either the shape of the curve or surface is important for manufacturing or engineering reasons or the shape affects the convergence of numerical algorithms which use the curve or surface or the placement of knots affects the accuracy of the fits. In all cases the class of functions used is that of parametric spline curves and tensor or direct product spline surfaces. The reason for choosing this class is that splines provide flexible models that are easily evaluated and stored. Furthermore, the B-spline representation of splines leads to convenient expressions for shape control over regions.

Ferguson, D. R.↗
NASA NTRS1992

Low-speed longitudinal and lateral-directional aerodynamic characteristics of the X-31 configuration

An experimental investigation of a 19 pct. scale model of the X-31 configuration was completed in the Langley 14 x 22 Foot Subsonic Tunnel. This study was performed to determine the static low speed aerodynamic characteristics of the basic configuration over a large range of angle of attack and sideslip and to study the effects of strakes, leading-edge extensions (wing-body strakes), nose booms, speed-brake deployment, and inlet configurations. The ultimate purpose was to optimize the configuration for high angle of attack and maneuvering-flight conditions. The model was tested at angles of attack from -5 to 67 deg and at sideslip angles from -16 to 16 deg for speeds up to 190 knots (dynamic pressure of 120 psf).

Banks, Daniel W.↗
NASA NTRS1986

Calculated performance, stability and maneuverability of high-speed tilting-prop-rotor aircraft

The feasibility of operating tilting-prop-rotor aircraft at high speeds is examined by calculating the performance, stability, and maneuverability of representative configurations. The rotor performance is examined in high-speed cruise and in hover. The whirl-flutter stability of the coupled-wing and rotor motion is calculated in the cruise mode. Maneuverability is examined in terms of the rotor-thrust limit during turns in helicopter configuration. Rotor airfoils, rotor-hub configuration, wing airfoil, and airframe structural weights representing demonstrated advance technology are discussed. Key rotor and airframe parameters are optimized for high-speed performance and stability. The basic aircraft-design parameters are optimized for minimum gross weight. To provide a focus for the calculations, two high-speed tilt-rotor aircraft are considered: a 46-passenger, civil transport and an air-combat/escort fighter, both with design speeds of about 400 knots. It is concluded that such high-speed tilt-rotor aircraft are quite practical.

Johnson, Wayne↗
NASA NTRS1986

Calculated performance, stability, and maneuverability of high-speed tilting-prop-rotor aircraft

The feasability of operating tilting-prop-rotor aircraft at high speeds is examined by calculating the performance, stability, and maneuverability of representative configurations. The rotor performance is examined in high-speed cruise and in hover. The whirl-flutter stability of the coupled-wing and rotor motion is calculated in the cruise mode. Maneuverability is examined in terms of the rotor-thrust limit during turns in helicopter configuration. Rotor airfoils, rotor-hub configuration, wing airfoil, and airframe structural weights representing demonstrated advanced technology are discussed. Key rotor and airframe parameters are optimized for high-speed performance and stability. The basic aircraft-design parameters are optimized for minimum gross weight. To provide a focus for the calculations, two high-speed tilt-rotor aircraft are considered: a 46-passenger, civil transport and an air-combat/escort fighter, both with design speeds of about 400 knots. It is concluded that such high-speed tilt-rotor aircraft are quite practical.

Johnson, Wayne↗
NASA NTRS2006

Performance, Loads and Stability of Heavy Lift Tiltrotors

Summaries of rotor performance are presented for a 124,000-lb Large Civil Tilt Rotor (LCTR) design, along with isolated-rotor and fully-coupled wing/rotor aeroelastic stability. A major motivation of the present research is the effect of size on rotor dynamics. Simply scaling up existing rotor designs to the vehicle size under study would result in unacceptable rotor weight. The LCTR was the most promising of several large rotorcraft concepts produced by the NASA Heavy Lift Rotorcraft Systems Investigation. It was designed to carry 120 passengers for 1200 nm, with performance of 350 knots at 30,000 ft altitude. Design features included a low-mounted wing and hingeless rotors, with a very low cruise tip speed of 350 ft/sec. The LCTR was sized by the'RC code developed by the U. S. Army Aeroflightdynamics Directorate. The rotor was then optimized using the CAMRAD II comprehensive analysis code. The blade and wing structures were designed by Pennsylvania State University to meet the rotor loads calculated by CAMRAD II and wing loads required for certification. Aeroelastic stability was confirmed by further CAMRAD II analysis, based on the optimized rotor and wing designs.

Acree, Cecil W., Jr.↗