Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Ignition probability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2012

Experimental Investigation of Augmented Spark Ignition of a LO2/LCH4 Reaction Control Engine at Altitude Conditions

The use of nontoxic propellants in future exploration vehicles would enable safer, more cost-effective mission scenarios. One promising green alternative to existing hypergols is liquid methane (LCH4) with liquid oxygen (LO2). A 100 lbf LO2/LCH4 engine was developed under the NASA Propulsion and Cryogenic Advanced Development project and tested at the NASA Glenn Research Center Altitude Combustion Stand in a low pressure environment. High ignition energy is a perceived drawback of this propellant combination; so this ignition margin test program examined ignition performance versus delivered spark energy. Sensitivity of ignition to spark timing and repetition rate was also explored. Three different exciter units were used with the engine s augmented (torch) igniter. Captured waveforms indicated spark behavior in hot fire conditions was inconsistent compared to the well-behaved dry sparks. This suggests that rising pressure and flow rate increase spark impedance and may at some point compromise an exciter s ability to complete each spark. The reduced spark energies of such quenched deliveries resulted in more erratic ignitions, decreasing ignition probability. The timing of the sparks relative to the pressure/flow conditions also impacted the probability of ignition. Sparks occurring early in the flow could trigger ignition with energies as low as 1 to 6 mJ, though multiple, similarly timed sparks of 55 to 75 mJ were required for reliable ignition. Delayed spark application and reduced spark repetition rate both correlated with late and occasional failed ignitions. An optimum time interval for spark application and ignition therefore coincides with propellant introduction to the igniter.

Kleinhenz, Julie↗
NASA NTRS2012

Spark Ignition Characteristics of a L02/LCH4 Engine at Altitude Conditions

The use of non-toxic propellants in future exploration vehicles would enable safer, more cost effective mission scenarios. One promising "green" alternative to existing hypergols is liquid methane/liquid oxygen. To demonstrate performance and prove feasibility of this propellant combination, a 100lbf LO2/LCH4 engine was developed and tested under the NASA Propulsion and Cryogenic Advanced Development (PCAD) project. Since high ignition energy is a perceived drawback of this propellant combination, a test program was performed to explore ignition performance and reliability versus delivered spark energy. The sensitivity of ignition to spark timing and repetition rate was also examined. Three different exciter units were used with the engine s augmented (torch) igniter. Propellant temperature was also varied within the liquid range. Captured waveforms indicated spark behavior in hot fire conditions was inconsistent compared to the well-behaved dry sparks (in quiescent, room air). The escalating pressure and flow environment increases spark impedance and may at some point compromise an exciter s ability to deliver a spark. Reduced spark energies of these sparks result in more erratic ignitions and adversely affect ignition probability. The timing of the sparks relative to the pressure/flow conditions also impacted the probability of ignition. Sparks occurring early in the flow could trigger ignition with energies as low as 1-6mJ, though multiple, similarly timed sparks of 55-75mJ were required for reliable ignition. An optimum time interval for spark application and ignition coincided with propellant introduction to the igniter and engine. Shifts of ignition timing were manifested by changes in the characteristics of the resulting ignition.

Kleinhenz, Julie↗
NASA NTRS2012

Spark Ignition Characteristics of a LO2/LCH4 Engine at Altitude Conditions

The use of non-toxic propellants in future exploration vehicles would enable safer, more cost effective mission scenarios. One promising "green" alternative to existing hypergols is liquid methane/liquid oxygen. To demonstrate performance and prove feasibility of this propellant combination, a 100lbf LO2/LCH4 engine was developed and tested under the NASA Propulsion and Cryogenic Advanced Development (PCAD) project. Since high ignition energy is a perceived drawback of this propellant combination, a test program was performed to explore ignition performance and reliability versus delivered spark energy. The sensitivity of ignition to spark timing and repetition rate was also examined. Three different exciter units were used with the engine's augmented (torch) igniter. Propellant temperature was also varied within the liquid range. Captured waveforms indicated spark behavior in hot fire conditions was inconsistent compared to the well-behaved dry sparks (in quiescent, room air). The escalating pressure and flow environment increases spark impedance and may at some point compromise an exciter.s ability to deliver a spark. Reduced spark energies of these sparks result in more erratic ignitions and adversely affect ignition probability. The timing of the sparks relative to the pressure/flow conditions also impacted the probability of ignition. Sparks occurring early in the flow could trigger ignition with energies as low as 1-6mJ, though multiple, similarly timed sparks of 55-75mJ were required for reliable ignition. An optimum time interval for spark application and ignition coincided with propellant introduction to the igniter and engine. Shifts of ignition timing were manifested by changes in the characteristics of the resulting ignition.

Kleinhenz, Julie↗
NASA NTRS2021

Compact Augmented Spark Igniters for Liquid Rocket Engines

The objective of this dissertation is to characterize augmented spark impinging (torch) igniters. Torch igniters inject propellants into a small prechamber where a spark igniter imparts the activation energy to initiate combustion. The flame stabilizes within the prechamber and exits into the main combustion chamber where it ignites the main flow directly or by mixing with a coaxial flow to create a secondary flame. The underlying phenomena that promote reliable ignition are multifaceted and required a broad scope of investigations. Initial efforts focused on spark discharges across an annular geometry. Gaseous propellent projects the electrical arc toward the prechamber, where the arc and the thermal energy is imparted to the surrounding fluid then meets with a combustible mixture. Discharges are parametrically examined against pressure, spark-gap size, and exciter types to emulate transient engine startup. The energy imparted to the flow, approximate velocity, and distance traveled by the exhaust plume are determined. Spark quenching (no energy deposition) and its effects on perceived versus actual measurements are shown. Results outline the prechamber target zone where a combustible mixture is necessary for ignition. Next, three-dimensional, time-accurate, and nonreacting computational fluid dynamics simulations assess effects of geometric and mass flow differences on the size, location, and composition of a combustible mixture. Fluid dynamic phenomena are elucidated. Correlations between nondimensional variables are found. Results are coupled with a conservation-law analysis to produce novel objective functions. Lastly, a full-scale, modular torch igniter is tested. Injector sizes, mixture ratios, and injector momentum ratios are systematically varied to map ignition probability and ignition delay. Results show the importance of local mixture ratios, provide injector momentum ratios guidelines, and demonstrate reliable ignition of core mixture ratios typically outside flammability limits. The deliverable of this project is not a torch igniter or derivative thereof. Instead, this dissertation produces novel objective-functions for igniter design. These equations are functions of variables that may be constrained by engine-level requirements, physics, and experimental results from this work. They provide a foundation for future igniter design and will minimize iterative processes from the design cycle for next-generation ignition hardware.

Torch Igniter↗
NASA NTRS1974

A review of the compatibility of structural materials with oxygen

Consideration of the problem of ignition and combustion of structural materials, particularly metals, which may come in contact with oxygen during its production, transport, and use. Following a review of the historical development of compatibility problems and research, a detailed account is given of compatibility testing methods aimed at detecting probable ignition sources, such as mechanical impact, electric sparks or flashes, heat, sound waves, abrasion, and surface fractures. A summary is presented of the ignition and combustion research reported in the literature, dwelling particularly on papers concerning oxygen-related accidents and the compatibility of metals with high-pressure oxygen. The relative oxygen compatibility of a number of common materials is discussed, including that of nickel and copper alloys, stainless steels, aluminum alloys, and titanium alloys. Finally, an effort is made to pinpoint research areas which would enhance understanding of the compatibility of bulk materials.

Clark, A. F.↗
NASA NTRS1985

Transition region ignition characteristics of n-heptane fuel sprays

Ignition studies were perferred on monodisperse n-heptane sprays at atmospheric pressure over a range of equivalence ratios and droplet diameters. A capacitive discharge spark ignition system was used as the ignition source, providing independent control of spark energy and duration. Preliminary measurements were made to optimize spark duration and spark gap, optimum conditions being those at which the maximum frequency or probability of ignition was observed. The effect of spark duration on ignition frequency for several spark energies was determined for equivalence ratios of 0.5 and 1.0 and initial droplet diameters of 28 and 68 microns. Spark duration had little effect on ignition frequency over the entire 15 to 170 mu s range examined. Spark durations of 70 to 80 mu s were used for all subsequent work. The spark gap was optimized at equivalence ratios of 0.6, 0.8 and 1.0 and initial droplet diameters of 30, 40, 50, 60 and 70 microns by varying the electrode spacing from 0.5 to 5.0 mm while maintaining a constant spark energy. The optimum gap was determined to be 3.0 mm for nearly all conditions.

Danis, A. M.↗
NASA NTRS1986

Combustion characteristics in the transition region of liquid fuel sprays

A number of important effects have been observed in the droplet size transition region in spray combustion systems. In this region, where the mechanism of flame propagation is transformed from diffusive to premixed dominated combustion, the following effects have been observed: (1) maxima in burning velocity; (2) extension of flammability limits; (3) minima in ignition energy; and (4) minima in NOx formation. A monodisperse aerosol generator has been used to form and deliver a well controlled liquid fuel spray to the combustion test section where measurements of ignition energy have been made. The ignition studies were performed on monodisperse n-heptane sprays at atmospheric pressure over a range of equivalence ratios and droplet diameters. A capacitive discharge spark ignition system was used as the ignition source, providing independent control of spark energy and duration. Preliminary measurements were made to optimize spark duration and spark gap, optimum conditions being those at which the maximum frequency or probability of ignition was observed. Using the optimum electrode spacing and spark duration, the frequency of ignition was determined as a function of spark energy for three overall equivalence ratios (0.6, 0.8, and 1.0) and for initial droplet diameters of 25, 40, 50, 60, and 70 micro m.

Cernansky, N. P.↗
NASA NTRS1985

Ignition characteristics of rich n-heptane fuel sprays in the transition region

Ignition studies were performed on monodisperse n-heptane sprays at atmospheric pressure over a range of equivalence ratios and droplet diameters. A capacitive discharge spark ignition system was used as the ignition source, providing independent control of spark energy and duration. Preliminary measurements were made to optimize spark duration and spark gap, optimum conditions being those at which the maximum frequency or probability of ignition was observed. Using the optimum electrode spacing and spark duration, the frequency of ignition was determined as a function of spark energy for three overall equivalence ratios (0.6, 0.8, and 1.0) and for initial droplet diameters of 25, 40, 50, 60, and 70 microns. An LDA system was used to determine the actual equivalence ratio at the spark gap, which varied from 1.5 to 4.7. The spark energy at which the frequency of ignition was 90 percent was defined as the minimum ignition energy. These data indicated that the ignitability of the sprays was enhanced as the equivalence ratio was increased, but was diminished as the droplet size was increased. The increase in minimum ignition energy with increasing droplet size and fixed equivalence ratio was nearly linear over the range of parameters studied. However, the effect became smaller with increasing equivalence ratio.

Danis, A. M.↗
NASA NTRS1999

Experimental Verification of Material Flammability in Space

The flammability in microgravity of three US-furnished materials, Delrin, polymethylmethacrylate (PMMA), and high-density polyethylene, was determined using a Russian-developed combustion tunnel on Mir. Four 4.5-mm-diameter cylindrical samples of each plastic were ignited under concurrent airflow (in the direction of flame spread) with velocities from no flow to 8.5 cm/s. The test results identify a limiting air-flow velocity V(sub lim) for each material, below which combustion ceases. Nominal values are V(sub lim) < 0.3 cm/s for Delrin, 0.5 cm/s for PMMA, and 0.3 to 0.5 cm/s for polyethylene. These values are lower than those obtained in prior ground testing. Nevertheless, they demonstrate that flow shutoff is effective for extinguishment in the microgravity environment of spacecraft. Microgravity test results also show that the plastic materials maintain a stable melt ball within the spreading flame zone. In general, as the concurrent flow velocity V decreases, the flame-spread rate V(sub F) decreases, from an average (for all three materials) of V(sub F)= 0.5-0.75 mm/s at V = 8.5 cm/s to V(sub F)= 0.05-0.01 mm/s at V = 0.3-0.5 cm/s. Also, as V decreases, the flames become less visible but expand, increasing the probability of igniting an adjacent surface.

Ivanov, A. V.↗
NASA NTRS1969

Combustion Processes in the Aerospace Environment

The aerospace environment introduces new and enhanced fire hazards because the special atmosphere employed may increase the frequency and intensity of fires, because the confinement associated with aerospace systems adversely affects the dynamics of fire development and control, and because the hostile external environments limit fire control and rescue operations. Oxygen enriched atmospheres contribute to the fire hazard in aerospace systems by extending the list of combustible fuels, increasing the probability of ignition, and increasing the rates of fire spread and energy release. A system for classifying atmospheres according to the degree of fire hazard, based on the heat capacity of the atmosphere per mole of oxygen, is suggested. A brief exploration of the dynamics of chamber fires shows that such fires will exhibit an exponential growth rate and may grow to dangerous size in a very short time. Relatively small quantities of fuel and oxygen can produce a catastrophic fire in a closed chamber.

Huggett, Clayton↗
NASA NTRS1997

An Investigation to Improve Quality Evaluations of Primers and Propellant for 20mm Munitions

To reduce the frequency of electrically initiated, 20mm munition hangfires (delayed ignitions), a joint Army/NASA investigation was conducted to recommend quality evaluation improvements for acceptance of both primers and gun propellant. This effort focused only on evaluating ignition and combustion performance as potential causes of hangfires: poor electrical initiation of the primer, low output performance of the primer, low ignition sensitivity of the gun propellant, and the effects of cold temperature. The goal was to determine the "best" of the Army and NASA test methods to assess the functional performance of primers and gun propellants. The approach was to evaluate the performance of both high-quality and deliberately defective primers to challenge the sensitivity of test methods. In addition, the ignition sensitivity of different manufacturing batches of gun propellants was evaluated. The results of the investigation revealed that improvements can be made in functional evaluations that can assist in identifying and reducing ignition and performance variations. The "best" functional evaluation of primers and propellant is achieved through a combination of both Army and NASA test methods. Incorporating the recommendations offered in this report may provide for considerable savings in reducing the number of cartridge firings, while significantly lowering the rejection rate of primer, propellant and cartridge lots. The most probable causes for ignition and combustion-related hangfires were the lack of calcium silicide in the primer mix, a low output performance of primers, and finally, poor ignition sensitivity of gun propellant. Cold temperatures further reduce propellant ignition sensitivity, as well as reducing burn rate and chamber pressures.

Bement, L. J.↗
NASA NTRS1971

Pyrotechnic hazards classification and evaluation program. Phase 2, segment 3: Test plan for determining hazards associated with pyrotechnic manufacturing processes

A comprehensive test plan for determining the hazards associated with pyrotechnic manufacturing processes is presented. The rationale for each test is based on a systematic analysis of historical accounts of accidents and a detailed study of the characteristics of each manufacturing process. The most hazardous manufacturing operations have been determined to be pressing, mixing, reaming, and filling. The hazard potential of a given situation is evaluated in terms of the probabilities of initiation, communication, and transition to detonation (ICT). The characteristics which affect the ICT probabilities include the ignition mechanisms which are present either in normal or abnormal operation, the condition and properties of the pyrotechnic material, and the configuration of the processing equipment. Analytic expressions are derived which describe the physical conditions of the system, thus permitting a variety of processes to be evaluated in terms of a small number of experiments.

Source record↗
NASA NTRS1984

Ignition phenomena of bulk aluminum alloy as a function of oxygen pressure

An ignition phenomena of 6061 aluminum alloy was investigated as a function of oxygen pressure. Cylindrical aluminum alloy specimens were ignited in a pure oxygen environment by a focused CW CO2 laser beam. The experiments were conducted at oxygen pressures ranging from 0.084 to 2.413 MPa. The temperature history of the entire upper surface of the specimen and of a 0.5 mm diameter spot located initially at the center of the specimen top surface was recorded by using a commercial two-color ratio pyrometer and a fast-response, narrow-band, two-color pyrometer. Mass, brightness, and interior temperatures (for certain experiments) were also recorded throughout the experiment. The results show that the surface temperatures at ignition of the alloy obtained from the temperature curves are below the melting temperature of the aluminum oxide and are slightly dependent on oxygen pressure. The data indicate that the ignition mechanism is complex and probably composed of several phenomena acting both separately and in conjunction with each other.

Nguyen, K.↗
NASA NTRSDate not supplied

Emissions Characterization and Smoke Transport of A Prescribed Fire

Under the background of climate change, vast regions of the world will face a hotter and probably drier future that favors ignition and spread of wildfires. This poses additional challenges to the communities who are fighting the ever-larger wildfires. Fire and smoke models are valuable tools to fire managers and decision-makers to mitigate the impact of fires. Existing fire modeling systems bear large uncertainties due to the difficulty in collecting data to characterize fire behavior and smoke transport. More observations are urgently needed for improvement of fire modeling and reduction in model uncertainty. The coordinated prescribed burn experiment, such as the Fire and Smoke Model and Measurement Evaluation Experiment (FSMMEE), will allow the concurrent collection of critical measurements of fuel, fire behavior, smoke, and meteorology to better understand and model fires. In this preliminary investigation, we employed the data from the prescribed burn experiment at Langdon Mountain, Utah, in November 2019, to reconstruct the fire emissions and characterize the smoke transport. The NASA Unified Weather Research and Forecasting Model (NU-WRF) was utilized to assist in identifying the potential pre-fire remote sensing capabilities, such as fuel load, moisture, and fire radiative power, which are helpful to model development and advancement. Along the way, two sets of NU-WRF experiments would be done by applying either a default fire emissions inventory (i.e., NASA’s Quick Fire Emissions Dataset, QFED) or reconstructed fire emissions using the data collected from the prescribed fire. The results would help answer the questions such as “How do reconstructed emissions compare to QFED emissions and their impact on plume transport”.

NU-WRF↗
NASA NTRS2000

Predictability of Gaseous Impact Ignition Sensitivity from Autoignition Temperature Data

An analysis of cumulative binomial probabilities for a quantal-type test like ASTM G74 indicates that for a probability of reaction in a single trial of 0.05, the probability of obtaining zero reactions in 20 trials is only approximately 36 percent, Because the lack of precision with the ASTM G74 test logic could be potentially misleading, an investigation was conducted to determine if pneumatic impact sensitivity could be predicted more reliably from other, more precise test methods. Pneumatic impact sensitivity tests were conducted following ASTM G74, but employing more rigorous test logics; autoignition temperature tests were conducted per ASTM G72. Polytetrafluoroethylene (PTFE), Viton A, polyethylene, polyoxymethylene polyamide, and silicone were the polymers used. After a fixed number of pneumatic impact tests was performed at set pressures, a plot of reaction frequency over a 3.4 to 24.1 MPa impact pressure range indicated that PTFE, Viton A, and silicone would outperform other polymers. The 50 percent pneumatic impact reactivity level was determined with the Bruceton test method. The data obtained resulted in a strong correlation between the 50 percent reactivity level and the autoignition temperature of polymers, indicating similar ignition mechanisms.

Hirsh, David↗
NASA NTRS2013

Piezoelectrically Initiated Pyrotechnic Igniter

This innovation consists of a pyrotechnic initiator and piezoelectric initiation system. The device will be capable of being initiated mechanically; resisting initiation by EMF, RF, and EMI (electromagnetic field, radio frequency, and electromagnetic interference, respectively); and initiating in water environments and space environments. Current devices of this nature are initiated by the mechanical action of a firing pin against a primer. Primers historically are prone to failure. These failures are commonly known as misfires or hang-fires. In many cases, the primer shows the dent where the firing pin struck the primer, but the primer failed to fire. In devices such as "T" handles, which are commonly used to initiate the blowout of canopies, loss of function of the device may result in loss of crew. In devices such as flares or smoke generators, failure can result in failure to spot a downed pilot. The piezoelectrically initiated ignition system consists of a pyrotechnic device that plugs into a mechanical system (activator), which on activation, generates a high-voltage spark. The activator, when released, will strike a stack of electrically linked piezo crystals, generating a high-voltage, low-amperage current that is then conducted to the pyro-initiator. Within the initiator, an electrode releases a spark that passes through a pyrotechnic first-fire mixture, causing it to combust. The combustion of the first-fire initiates a primary pyrotechnic or explosive powder. If used in a "T" handle, the primary would ramp the speed of burn up to the speed of sound, generating a shock wave that would cause a high explosive to go "high order." In a flare or smoke generator, the secondary would produce the heat necessary to ignite the pyrotechnic mixture. The piezo activator subsystem is redundant in that a second stack of crystals would be struck at the same time with the same activation force, doubling the probability of a first strike spark generation. If the first activation fails to ignite, the device is capable of multiple attempts. Another unique aspect is in the design of the pyrotechnic device. There is an electrode that aids the generation of a directed spark and the use of a conductive matrix to support the first-fire material so that the spark will penetrate to the second electrode.

Quince, Asia↗
NASA NTRS1987

Investigation of the reaction of liquid hydrogen with liquid air in a pressure tube

A pressure tube should protect the FR-2 reactor from the consequences of a hydrogen-air reaction, which is conceivable in the breakdown of several safety devices of the planned cold neutron source Project FR-2/16. The magnitudes and time pattern of the pressures to be expected were investigated. In the geometry used and the ignition mechanism selected, which is comparable to the strongest ignition process conceivable in the reactor, the reaction proceeds with greater probability than combustion. The combustion is possibly smaller if local limited partial detonations are superimposed. The magnitude of the pressure was determined by the masses of the reaction partners, liquid H2 and liquid air, and determines their ratio to each other.

Karb, Erich H.↗
NASA NTRS2005

Common Cause Case Study: An Estimated Probability of Four Solid Rocket Booster Hold-down Post Stud Hang-ups

Until Solid Rocket Motor ignition, the Space Shuttle is mated to the Mobil Launch Platform in part via eight (8) Solid Rocket Booster (SRB) hold-down bolts. The bolts are fractured using redundant pyrotechnics, and are designed to drop through a hold-down post on the Mobile Launch Platform before the Space Shuttle begins movement. The Space Shuttle program has experienced numerous failures where a bolt has "hung-up." That is, it did not clear the hold-down post before liftoff and was caught by the SRBs. This places an additional structural load on the vehicle that was not included in the original certification requirements. The Space Shuttle is currently being certified to withstand the loads induced by up to three (3) of eight (8) SRB hold-down post studs experiencing a "hang-up." The results af loads analyses performed for four (4) stud-hang ups indicate that the internal vehicle loads exceed current structural certification limits at several locations. To determine the risk to the vehicle from four (4) stud hang-ups, the likelihood of the scenario occurring must first be evaluated. Prior to the analysis discussed in this paper, the likelihood of occurrence had been estimated assuming that the stud hang-ups were completely independent events. That is, it was assumed that no common causes or factors existed between the individual stud hang-up events. A review of the data associated with the hang-up events, showed that a common factor (timing skew) was present. This paper summarizes a revised likelihood evaluation performed for the four (4) stud hang-ups case considering that there are common factors associated with the stud hang-ups. The results show that explicitly (i.e. not using standard common cause methodologies such as beta factor or Multiple Greek Letter modeling) taking into account the common factor of timing skew results in an increase in the estimated likelihood of four (4) stud hang-ups of an order of magnitude over the independent failure case.

Cross, Robert↗