Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ION IMPACT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Entropy-Stabilized Multication Fluorides as a Conversion-Type Cathode for Li-Ion Batteries–Impact of Element Selection

Metal fluorides (e.g., FeF 2 and FeF 3 ) have received attention as conversion-type cathode materials for Li-ion batteries due to their higher theoretical capacity compared to that of common intercalation materials. However, their practical use has been hindered by low round-trip efficiency, voltage hysteresis, and capacity fading. Cation substitution has been proposed to address these challenges, and recent advancements in battery performance involve the introduction of entropy stabilization in an attempt to facilitate reversible conversion reactions by increasing configurational entropy. Building on this concept, high entropy fluorides with five cations were synthesized by using a simple mechanochemical route. In order to examine the impact of element selection, Co 0.2 Cu 0.2 Ni 0.2 Zn 0.2 Fe 0.2 F 2 (HEF-Fe) was compared with Co 0.2 Cu 0.2 Ni 0.2 Zn 0.2 Mg 0.2 F 2 (HEF-Mg), replacing electrochemically inactive Mg with Fe as an active participant in the conversion reaction. Combining electrochemical measurements with first-principles calculations, high-resolution electron microscopy, and synchrotron X-ray analysis, HEFs’ battery performances and conversion reaction mechanisms were investigated in detail. The results highlighted that replacement of Mg with Fe was beneficial, with enhanced capacity, rate capability, and surface stability. In addition, it was found that HEF-Fe showed similar cycle stability without an electrochemically inactive element. In conclusion, these findings provide valuable insights for the design of high entropy multielement fluorides for improved Li-ion battery performance.

25 ENERGY STORAGE↗
DOE OSTI2026

Hanford Tank Waste Matrix Impact on Ion Exchange Performance Using Crystalline Silicotitanate

The removal of radiocesium from Hanford tank waste supernate is a critical step in preparing feed for low-activity waste immobilization. This study evaluated cesium ion exchange performance using crystalline silicotitanate (CST) media in a series of tests designed to evaluate the influence of waste matrix variability on capacity and kinetics. Tank waste supernate subsampled from five Hanford double-shell tanks encompassed a range of sodium, hydroxide, nitrate, and nitrite concentrations in order to assess the impact of feed variability on the performance of the ion exchange system. Both equilibrium and dynamic ion exchange tests were conducted to quantify cesium distribution coefficients and breakthrough behavior under prototypic operating conditions. Results indicated that effective cesium capacity varied by up to a factor of five across the matrices tested, with higher sodium concentrations significantly reducing uptake. Kinetic behavior was similarly matrix-dependent, with solution viscosity contributing to a twofold variation in mass-transfer rates. These results demonstrate the strong dependence of CST ion exchange performance on waste composition and must be incorporated into predictive models for future treatment system design and optimization.

Westesen, Amy M.↗
DOE OSTI2025

Deep potential molecular dynamics simulations of ion-enhanced etching of silicon by atomic chlorine

The continued development of plasma-assisted processing techniques requires a fundamental understanding of plasma-surface interactions. Molecular dynamics (MD) simulations have been employed to complement experimental studies and better understand the properties of such systems. Recently, machine learning (ML) methods have enabled the development of ab initio-based interatomic potentials, which can be generalized to complex combinations of multiple atom types. In this work, we use ML potentials developed using the Deep Potential Molecular Dynamics (DeepMD) framework to provide a model of ion-enhanced etching of Si by Cl atoms. We demonstrate the importance of proper selection of the training data set to the accuracy of the DeepMD model and compare our results to MD results using empirical potentials, as well as to experimental measurements. Exposure of undoped Si at 300 K to thermal Cl atoms yields a steady-state Cl coverage of 1.25 monolayers, which is slightly lower than the value obtained in previous experimental studies. Predictions of Si etch yields by simultaneous Cl atom and Ar + ion impacts as a function of ion energy, neutral to ion flux ratio, and angle of incidence of the ions are in reasonably good agreement with classical MD results and experimental measurements. Finally, etch yields and SiCl x mixed layer thicknesses during simultaneous bombardment of the Si(100) surface by Cl atoms and Cl + ions are in good agreement with experimental data. In conclusion, the present work is a necessary condition for the extension of the DeepMD procedure to more complex systems of interest in plasma-surface interactions.

Artificial neural networks↗
DOE OSTI2025

Coordinated Cation Transport in Ti 3 C 2 T x MXene Membranes

Membrane nanofiltration is an attractive strategy for the selective recovery of high-demand metals from wastewater and brine. Effective sieving of ions in aqueous environments will require precise control over membranes’ nanochannel size and chemistry. Ti 3 C 2 T x MXene is an environmentally stable 2D material that can be processed into laminar membranes containing nanoscale interlayer spaces. The MXene interlayer environment depends on the ion species and amount of water intercalated between MXene sheets, and it is the major factor governing permeation and selectivity through MXene membranes. Coordinated ion–ion and ion-interlayer dynamics in the presence of complex mixtures can impact ion permeability and selectivity. Herein, we observe strong competitive effects between different cations (Li + , Na + , and Ca 2+ ) in binary mixtures, resulting in reduced selectivity when compared with single-salt permeability ratios. X-ray diffraction, molecular dynamics, and density functional theory simulations support the conclusion that cations with stronger attraction to MXene flakes can preferentially occupy the MXene nanochannels and hinder other ions via charge or size exclusion. In conclusion, elucidation of ion transport behavior in MXene under complex conditions will allow for more rational design of efficient ion-sieving membranes.

2D Materials↗
DOE OSTI2025

Understanding the Quadrupole Mass Filter and Testing a High-Resolution QMS RGA for ITER

A common type of residual gas analyzer is the quadrupole mass spectrometer. One of the main components within this instrument is a mass filter known as the quadrupole. It is responsible for the selective throughput of the ionized gas particles - by ascending mass number - prior to ion impacts on the analyzer (or detector) surface from which the ion current signal is generated for processing. However, the quadrupole is not fully described in relation to the electric field characteristics and the function as an ion mass separator. This paper describes the basic origins of the electrical design, the intricate assembly criteria, and performance of the quadrupole within the spectrometer. A specialized quadrupole mass spectrometer is part of a configuration for a diagnostic gas analyzer system planned for ITER, a fusion research machine. It has a verified capability, essential as a diagnostic criterion for this reactor project, to successfully deconvolute the mass signals of Helium-4 and deuterium (reactor fuel exhaust gases, separated by only 0.026 atomic mass units), down to a relative three-percent concentration of the former gas. The associated preliminary testing, performed at the Oak Ridge National Laboratory, is also addressed. Finally, one of the key parameters used to express gas concentration, the relative sensitivity factor, will be explained, including an evaluation of dependency on other variables.

Marcus, Chris [ORNL] (ORCID:0000000190139636)↗
DOE OSTI2025

General kinetic ion-induced electron emission model for metallic walls applied to biased Z-pinch electrodes

A kinetic ion-induced electron emission (IIEE) model for general applications is developed to obtain the emitted electron energy spectrum for a distribution of ion impacts on a metallic surface. We assume an ionization cascade mechanism and use empirical models for the ion and electron stopping powers. The emission spectrum and the secondary electron yield (SEY) are validated for a variety of materials. The IIEE model is used to study the effect of IIEE on the plasma-material interactions of Z-pinch electrodes. Un-magnetized Boltzmann-Poisson simulations are performed for a Z-pinch plasma doubly bounded by two biased copper electrodes with and without IIEE at bias potentials from 0 to 9 kV. At the anode, the SEY decreases from 0 to 1 kV, but then increases at higher bias potentials. At the cathode, the SEY is much larger due to higher energy ion bombardment and grows with bias potential. As the bias potential increases, the emitted cathode electrons are accelerated to higher energies into the domain, collisionally heating the plasma. Above 1 kV, the heating is strong enough to increase the plasma potential. Despite SEY greater than 1, only a classical sheath forms as opposed to a space-charge limited or inverse sheath due to the emitted electron flux not reaching the space charge current saturation limits. Furthermore, the current in the emissionless cases saturates to a value lower than experiment. With IIEE, the current does not saturate and continues to increase with the 4 kV case, matching most closely with the experiment.

Carbon based materials↗
DOE OSTI2025

Erosion of high-Z refractory coatings for helicon plasma source window

Proto-MPEX (Materials Plasma Exposure eXperiment), a linear plasma device (LPD), using a high power radio frequency (RF) (⩾100 kW, 13.56 MHz) helicon plasma source, has suffered RF sheath-induced window erosion. The sputtered impurities from the window surface transport toward the downstream target affecting plasma-material interaction studies. The rectified sheath voltage formed was high enough to cause window erosion by light ions due to its low-Z components (e.g. Si 3 N 4 and AlN). Hence, we are proposing impurity mitigation strategies, which involve the application of a Faraday screen to lower the rectified sheath voltage and the application of high-Z refractory coatings on the existing window plasma-facing surface. In this work, we report the erosion of two different coatings, i.e., tantalum oxide (Ta 2 O 5 ) and hafnium oxide (HfO 2 ) on a silicon nitride (Si 3 N 4 ) window material under conditions of low-energy deuterium (D) ion impact, well below the Ta 2 O 5 sputtering energy threshold (i.e. 250 eV). The test samples were RF-biased and exposed to a high D-ion fluence (∼10 26 m −2 ) in Plasma Interaction with Surface Component Experimental Station (PISCES-A) LPD. The experimentally measured sputtering yields of the high-Z refractory coatings below the sputtering energy threshold of Ta 2 O 5 indicate an increased erosion due to the plasma impurities, especially due to oxygen. Improving the vacuum level could reduce the oxygen impurities and increase the lifespan of the coated helicon window for plasma operation. Post-surface analysis indicates no preferential erosion of oxygen or enrichment of the high-Z surface component. This is likely due to an effective energy transfer from the impurity ion for sputtering of the high-Z component in the coating. With the reduced rectified sheath voltage at the window surface and improved vacuum conditions, the proposed high-Z refractory coatings offer a promising solution for reducing window erosion in future MPEX plasma operations at ORNL.

RF bias↗
DOE OSTI2026

Recent advances in plasma control and physics research in the Large Helical Device

The Large Helical Device (LHD), the largest superconducting helical system in the world, is equipped with advanced heating and diagnostic tools, facilitating plasma control and physics research. Data assimilation was employed for electron temperature control using a real-time Thomson scattering system and real time prediction code. A virtual LHD environment enabled visualization of escaping high-energy tritium ions and demonstrated that these ions impact the rear side of the divertor plate. Pioneering results crucial to plasma control have also been achieved. Real-time wall conditioning using Lithium granule dropping improved bulk ion energy and particle transport while simultaneously enhancing the heavy impurity transport. Progress has also been made in the investigation of turbulence-driven transport. At the confinement bifurcation, ion-scale turbulence decreased, while electron-scale turbulence increased. A change in the anisotropy of turbulent eddies was also observed at the confinement bifurcation. Coexistence of local and non-local turbulence was identified in electron-scale turbulence. Non-local turbulence exhibited the rapid spatial propagation of perturbations throughout the plasma, while local turbulence followed the temperature gradient. A transition between drift-wave turbulence and magnetohydrodynamics (MHD) turbulence was observed with the turbulence minimized at the transition condition. Machine learning analysis was employed to evaluate the temperate and density conditions of this turbulence transition. Then, real-time control of fueling and heating was applied to maintain the turbulence transition condition, improving the energy confinement enhancement factor by 20%. In addition, evidence was obtained for collisionless ion heating by energetic-ion-driven geodesic acoustic modes and MHD bursts. These achievements represent unique contributions to the development of fusion reactors.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Cr plasma-material-interaction in PISCES-RF: D thermal release, retention, and erosion

Pure chromium (Cr) targets were exposed to high-flux deuterium (D) plasmas in the Pisces-RF linear plasma device, and measurements of D retention, release, and erosion were subsequently performed. Post-exposure D retention was quantified using temperature-programmed desorption on Cr targets irradiated by 50 eV ions over a broad range of exposure temperatures (423–873 K) and ion fluences (3 × 10 24 – 3 × 10 26 m −2 ). The retained D inventory was observed to decrease rapidly with increased exposure temperature, from approximately ∼7 × 10 20 m −2 at ∼ 420 K, to then saturate near ∼ 10 20 m −2 for exposure temperatures above ∼550 K. Separately, at fixed exposure temperature (∼450 K), D retention was found to have only a weak dependence on increasing ion fluence. Lastly, the erosion of Cr in D plasma was investigated for ion impact energies in the range 40 ≤ E i ≤ 250 eV. Erosion was inferred using optical emission spectroscopy (OES) from the ratio of emission lines (Cr I (425.4 nm)/D I (656.1 nm)) measured close to the target. Conversion of the OES yield data to net erosion yield was made with singular ion energy target mass-loss measurements. These net erosion yield data were then further corrected to obtain gross erosion yield by accounting for a re-deposition factor, computed using a simple model. The gross erosion yield is found to be 2–4 times lower than predicted by SDTrimSP, consistent with that typically observed for light-ion sputtering under high-flux plasma conditions.

Chromium↗
DOE OSTI2025

Impacts of Focused Ion Beam Processing on the Fabrication of Nanoscale Functionalized Probes

Herein, we examine the impact of Ga + ion kinetic energy and the target material type on the extent of ion implantation and structural damage in atomic force microscopy probes made of Al 2 O 3 and ZnO manufactured by focused ion beam (FIB) using scanning transmission electron microscopy and energy-dispersive X-ray mapping. Penetration of Ga into the Al 2 O 3 lattice induced structural distortions and amorphization. For ZnO probes, Ga is uniformly dispersed across the surface, resulting in the formation of distinct clusters. Atom probe tomography further validates the Ga distributions in Al 2 O 3 and ZnO nanoprobes. Complementary Monte Carlo simulations with the transport of ions in the matter program indicated that the introduction of Ga + prompts the generation of cation and anion vacancies, an occurrence more pronounced in Al 2 O 3 compared to ZnO. In conclusion, this study not only enriches the knowledge of ion-matter interactions, but also serves as a practical guide for the fabrication of nanoscale functionalized AFM probes.

Al2O3↗
DOE OSTI2026

Characterization of runaway electron impact on instrumented sacrificial limiters on DIII-D

Instrumented sacrificial limiter heads, both domed (proud) and flat (flush) are used in DIII-D runaway electron (RE) wall strikes to study the wall impact dynamics with high spatial and time resolution. The approximate structure of the RE wetted area and heating depth on the domed limiter heads were predicted qualitatively using orbit-tracking simulations, although a strong left–right asymmetry (about the magnetic field direction) was not captured well by the simulations. It is hypothesized that this difference is perhaps due to the local 3D magnetic field perturbation of the dome limiter head. The average kinetic energy K and pitch angle θ of REs striking the limiter head were estimated from the spatial distribution of local HXR emission and were estimated to be roughly K ≈ 4 MeV and θ ≈ 0.2 rad. These values are roughly consistent with in-plasma values estimated before the loss event, indicating that RE kinetic energy and pitch angle are not drastically altered when transporting to the wall. Large shot–shot variations (1–10 kJ) in energy deposition into the limiter head were observed and were explained by shot–shot variations in locked magneto-hydrodynamics mode toroidal phase. For the largest deposited energies (10 kJ), graphite material failure and explosive dust release was observed, and the depth of material failure at higher energy deposition was successfully reproduced using modelling of volumetric energy deposition and brittle failure. The presence of energetic (keV) level ion impact during the RE wall strike was confirmed by three different surface analysis techniques. The ratio of energetic ion to RE flux appears to be larger on flat surfaces within the RE wetted area, although the energetic ion flux and total energy flux due to energetic ions have not yet been quantified.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

From Cation Order to Disorder: Unlocking Ion Transport Pathways in Li–Zn–Zr–Cl Halospinels

Lithium metal chloride halospinels of the general formula Li 2 MCl 4 are a promising class of earth-abundant ion conductors for all-solid-state batteries. However, poor roomtemperature ionic conductivity has historically limited their use in practical applications. Here, we substitute Zr 4+ into Li 2 ZnCl 4 along the series Li 2−2x/3 Zn 1−x Zr 2x/3 Cl 4 (x = 0, 0.1, 0.3, 0.4, 0.6, 0.9, and 1.0) to understand how cation disorder and vacancy tuning impact ion transport in “normal” halospinels. Aliovalent Zr 4+ substitution increases ionic conductivity by nearly 5 orders of magnitude, from 1.320(3) × 10 −9 S cm −1 in Li 2 ZnCl 4 to 6.74(1)× 10 −5 S cm −1 for x = 0.6. Average and local structure characterization through synchrotron X-ray diffraction (SXRD) and neutron pair distribution function (nPDF) analysis reveal that Zr 4+ redistributes the Zn 2+ and Li + sublattices into previously unoccupied interstitial sites, which form new low-energy hopping pathways that facilitate ion transport. We rationalize the dramatic rearrangement of the cation local structure by considering the coordination preferences of the cations and the potential electrostatic penalties incurred by the higher-valent Zr 4+ cations. This work delivers an atomistic understanding of substitution-induced cation disorder and ion transport properties in a new family of earth-abundant halospinels.

Cardoza, Abby M. [Colorado School of Mines, Golden↗
DOE OSTI2024

Correction: Impact of lanthanide ion complexation and temperature on the chemical reactivity of N , N , N ′, N ′-tetraoctyl diglycolamide (TODGA) with the dodecane radical cation

Correction for ‘Impact of lanthanide ion complexation and temperature on the chemical reactivity of N , N , N ′, N ′-tetraoctyl diglycolamide (TODGA) with the dodecane radical cation’ by Gregory P. Horne et al. , Phys. Chem. Chem. Phys. , 2023, 25 , 16404–16413, https://doi.org/10.1039/D3CP01119D.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2025

Assessment of metadynamic recrystallization in single copper particle impacts by focused ion beam tomography

We study single Cu-on-Cu impacts relevant to cold spray deposition and quantitatively analyze the metadynamic recrystallization (mDRX) that takes place after the impact by virtue of lingering impact adiabatic heat. Unlike prior studies, the current full 3D tomographic analysis of the mDRX volume shows that mDRX is extremely common in such impacts, although it is often missed when examining 2D sections. We also report an unexpected trend: there is a “sour spot” for mDRX at velocities about 20–40 % above the velocity for particle adhesion. This non-monotonic trend is contrary to the expectations based on increasing adiabatic heating with velocity. With a schematic model, we show that the trend can be explained on the basis of heat transfer: cooling of the heat-affected region is limited by transport through the bonded regions at the particle-substrate interface. Thus, bonding has a prominent role in the heat dissipation process and the best bonded particles most rapidly bulk quench, avoiding mDRX. Here, the developed semi-empirical model aligns with the experimental findings and may help inform microstructural evolution during cold spray and post-spray processing.

FIB-SEM tomography↗
DOE OSTI2025

Si content in methacrylamide-containing A- b -(B- r -C) block copolymers and its impact on reactive ion etching properties

Block copolymers (BCPs) of an A-block-(B-random-C) architecture have been explored as materials for nanolithography because the composition and chemistry of the random block enables modification of thermodynamic and wetting properties to meet manufacturing criteria. Here, in this study, A-b-(B-r-C) BCPs created by an amidation reaction of polystyrene-block-poly(pentafluorophenyl methacrylate) (PS-b-PPFMA) with controlled amounts of Si add insight to previous conclusions about the dual contributions of BCP chemistry and reactive ion etch (RIE) gas chemistry on etch properties. We focus on two RIE etch characteristics: organosilicon etch resistance in H 2 /N 2 plasma etching and enhanced removal of non-styrenic structures in an Ar/O 2 etch. Consistent with previous studies, higher amounts of Si result in greater etch resistance under H 2 /N 2 RIE, where at least ∼10 wt. % Si is necessary to exhibit sufficient etch resistance. By contrast, Ar/O 2 etching resulted in etch rates independent of Si content. We observe previously unreported surface roughening aligned with morphological domains during the H 2 /N 2 etch of modified PS-b-PPFMA BCPs. Limited in the amount of allowable Si to attain equal surface energy between blocks, these BCPs are further disqualified in forming a Si-containing mask. However, in an Ar/O 2 etch, the same BCPs exhibit suitable etch contrast and smooth domain structures, forming a uniform PS mask. Ultimately, this study uses the chemical flexibility of these materials to demonstrate the mechanisms of interactions between BCP and etch chemistry that must be considered to design effective materials for pattern transfer applications.

Eom, Christopher J. [University of Chicago, IL (Un↗
DOE OSTI2026

Impact of Nd ions on the chemical kinetic behavior of radiolytic transients in molten LiCl-KCl-NdCl3 salt mixtures

Pyrochemical reprocessing technologies can be used to recover valuable materials from used nuclear fuel (UNF), such as uranium. However, other critical materials, such as fission product neodymium, are challenging to recover from molten chloride eutectic mixtures (LiCl-KCl) due to the presence of multivalent states (Nd2+/Nd3+), disproportionation reactions, and re-dissolution in the molten chloride salt. Understanding, predicting, and controlling these processes is further complicated by the presence of ionizing radiation fields, for which little is known on the interaction of neodymium ions with the radiolytic transients (es– and Cl2.–) in molten LiCl-KCl salt mixtures. Here, chemical kinetics, from integrated electron pulse irradiation and transient absorption spectroscopy, are presented for the reaction of Nd3+ ions with es– and Cl2.– as a function of temperature (400–600 ?).

36 - MATERIALS SCIENCE↗
DOE OSTI2025

Probing the impact of oxygen negative ions on the self-organized pattern in 1 atm DC glow with liquid anode

In an atmospheric DC glow discharge with a liquid anode, the plasma anode glow attached to the grounded liquid surface under certain conditions self-organizes into coherent patterns. Optical emission spectroscopy revealed that the emission consists primarily of the second positive system of nitrogen, N 2 (C-B), whose excitation energy is low and sensitive to changes in the electron energy distribution. In addition to electrons, negative ions can accumulate in the anode sheath and affect the local space charge. It has been speculated that these negative ions play a role in pattern formation at the anode surface. In this work, the role of oxygen negative ions was explored. It was found that the formation of anode patterns requires at least a 7% volume fraction of oxygen in the ambient gas. Results showed that O 2 - is the dominant negative ion species in atmospheric DC glow discharge, with a density of ~10 12 cm -3 . While the presence of oxygen appears to be crucial for pattern formation, this study indicated that patterns still formed without geometric changes even when 62% of negative ions in the plasma were detached by a laser. This suggests that negative ions do not support the patterns, while oxygen's heating effect may induce instability at the anode.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Quantum fluctuations in dense plasma simulations

Molecular dynamics (MD) simulations are a powerful tool for modeling warm and hot dense matter. Density functional theory (DFT) MD simulations are often preferred in dense plasmas in order to accurately model quantum electronic structure. However, DFT-MD simulations neglect interaction effects due to fluctuations in excited states. In this work, we present an MD approach that uses excited state method pseudoatoms to run dense plasma simulations with many different core-electron configurations at classical MD speeds. We also allow for transitions between different configurations in our simulations and find that these fluctuations are especially important for highly excited states. Our results suggest that finite configuration lifetimes that are comparable to the inverse ion plasma frequency need to be accounted for in order to accurately model ion distributions in dense plasma simulations. We also demonstrate that excited state fluctuations have a direct impact on ion plasma microfields, generate different plasma microfields for different excitation levels, and thereby induce absorption–emission line shape asymmetries even in steady-state plasmas.

36 MATERIALS SCIENCE↗