Engineering PapersSearch

SEARCH · Engineering Papers

Results for “INDEPENDENT VARIABLE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Machine learning method for enforcing variable independence in background estimation with LHC data: ABCDisCoTEC

A novel solution is presented for the problem of estimating the backgrounds of a signal search using observed data while simultaneously maximizing the sensitivity of the search to the signal. The 'ABCD method' provides a reliable framework for background estimation by partitioning events into one signal-enhanced region (A) and three background-enhanced control regions (B, C, and D) via two smoothly varying, statistically independent variables. In practice, even slight correlations between the two variables can significantly undermine the method's performance. Thus, choosing appropriate variables by hand can present a formidable challenge, especially when background and signal differ only subtly. To address this issue, the ABCD with distance correlation (ABCDisCo) method was developed to construct two learned variables via a neural network trained to provide strong signal-background discrimination with small values of the distance correlation (DisCo) measure between the two learned variables. However, relying solely on minimizing the DisCo can result in learned variables that may not have distributions of background events that are smoothly varying and localized at extreme values, as necessary for the validity of the background estimation. The ABCDisCo training enhanced with closure (ABCDisCoTEC) method is introduced to solve this issue by directly minimizing the nonclosure, expressed as a dedicated differentiable loss term. This extended method is applied to a data set of proton-proton collisions at a center-of-mass energy of 13 TeV recorded by the CMS detector at the CERN Large Hadron Collider. Additionally, given the complexity of the minimization problem with constraints on multiple loss terms, the modified differential method of multipliers is applied and shown to greatly improve the stability and robustness of the ABCDisCoTEC method, compared to grid search hyperparameter optimization procedures.

Hayrapetyan, Aram [Yerevan Phys. Inst.]

The development of the Poincare-similar elements with eccentric anomaly as the independent variable

A new set of element differential equations for the perturbed two-body motion is derived. The elements are canonical and are similar to the classical canonical Poincare elements, which have time as the independent variable. The phase space is extended by introducing the total energy and time as canonically conjugated variables. The new independent variable is, to within an additive constant, the eccentric anomaly. These elements are compared to the Kustaanheimo-Stiefel (KS) element differential equations, which also have the eccentric anomaly as the independent variable. For several numerical examples, the accuracy and stability of the new set are equal to those of the KS solution. This comparable accuracy result can probably be attributed to the fact that both sets have the same time element and very similar energy elements. The new set has only 8 elements, compared to 10 elements for the KS set. Both sets are free from singularities due to vanishing eccentricity and inclination.

Bond, V. R.

Assessment of Relative Velocity as Independent Variable for Space Shuttle First Stage Guidance Attitude Command Tables

The selection of relative velocity as the independent variable for the space shuttle first stage guidance attitude command tables was assessed to support the first stage guidance point design. The criterion for selecting the independent variable for first stage open loop guidance is to reduce or minimize performance dispersions, primarily those affecting structural loads. The products of angle of attack and angle of sideslip times dynamic pressure are used as load indicators, and minimizing their dispersions will indicate a minimum loads dispersion. Relative velocity is shown to be an acceptable steering independent variable.

Kimbrough, M.

A note on independent variables for restricted three-body problems.

In studies of the elliptic restricted three-body problem, the true anomaly of the motion of the primaries is often used as the independent variable. The equations of motion then show invariancy in form from the circular case. It is of interest whether other independent variables exist, such that the invariant form of the equations is maintained. It is found that true anomaly is the only such variable.

Heppenheimer, T. A.

Iterative Strain-Gage Balance Calibration Data Analysis for Extended Independent Variable Sets

A new method was developed that makes it possible to use an extended set of independent calibration variables for an iterative analysis of wind tunnel strain gage balance calibration data. The new method permits the application of the iterative analysis method whenever the total number of balance loads and other independent calibration variables is greater than the total number of measured strain gage outputs. Iteration equations used by the iterative analysis method have the limitation that the number of independent and dependent variables must match. The new method circumvents this limitation. It simply adds a missing dependent variable to the original data set by using an additional independent variable also as an additional dependent variable. Then, the desired solution of the regression analysis problem can be obtained that fits each gage output as a function of both the original and additional independent calibration variables. The final regression coefficients can be converted to data reduction matrix coefficients because the missing dependent variables were added to the data set without changing the regression analysis result for each gage output. Therefore, the new method still supports the application of the two load iteration equation choices that the iterative method traditionally uses for the prediction of balance loads during a wind tunnel test. An example is discussed in the paper that illustrates the application of the new method to a realistic simulation of temperature dependent calibration data set of a six component balance.

Ulbrich, Norbert Manfred

The development of the Poincare-similar elements with true anomaly as the independent variable

In reference 1, the Hamiltonian of the unperturbed two-body problem in extended phase space is established. Depending on the type of time transformation, eight canonical elements were developed with the true anomaly or the eccentric anomaly as the independent variable. These two new sets, DS(phi) and DS(u), however contain singularities for small eccentricities and inclinations. In reference 2, these singularities are removed by a transformation from DS(u) to eight canonical PS(u) elements. In reference 3, the DS(phi) variables are transformed to the PS(phi) elements to remove the singularities. However, no direct relation was established between the eight canonical PS(phi) elements and the Cartesian coordinates. It is the purpose of this report to establish those relations and to develop the perturbed equations of motion in the PS(phi) space. This report also demonstrates the accuracy of this new set when it is applied to numerical orbit prediction problems.

Mueller, A.

FIT: Computer Program that Interactively Determines Polynomial Equations for Data which are a Function of Two Independent Variables

A computer program for interactively developing least-squares polynomial equations to fit user-supplied data is described. The program is characterized by the ability to compute the polynomial equations of a surface fit through data that are a function of two independent variables. The program utilizes the Langley Research Center graphics packages to display polynomial equation curves and data points, facilitating a qualitative evaluation of the effectiveness of the fit. An explanation of the fundamental principles and features of the program, as well as sample input and corresponding output, are included.

Arbuckle, P. D.