Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “IMPREGNATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Recent progress and tests of radiation resistant impregnation materials for Nb{sub 3}Sn coils

Fermilab is collaborating with Lawrence Berkeley National Laboratory (LBNL) and Brookhaven National Laboratory (BNL) (US-LARP collaboration) to develop a large-aperture Nb{sub 3}Sn superconducting quadrupole for the Large Hadron Collider (LHC) luminosity upgrade. An important component of this work is the development of materials that are sufficiently radiation resistant for use in critical areas of the upgrade. This paper describes recent progress in characterization of materials, including the baseline CTD101K epoxy, cyanate ester blends, and Matrimid 5292, a bismaleimide-based system. Structural properties of “ten stacks” of cable impregnated with these materials are tested at room and cryogenic temperatures and compared to the baseline CT-101K. Experience with potting 1 and 2 meter long coils with Matrimid 5292 are described. Test results of a single 1-m coil impregnated with Matrimid 5292 are reported and compared to similar coils impregnated with the traditional epoxy.

43 PARTICLE ACCELERATORS↗

A Model for Tow Impregnation and Consolidation for Partially Impregnated Thermoset Prepregs

The formation and transport of voids in composite materials remains a key research area in composite manufacturing science. Knowledge of how voids, resin, and fiber reinforcement propagate throughout a composite material continuum from green state to cured state during an automated tape layup process is key to minimizing defects induced by void-initiated stress concentrations under applied loads for a wide variety of composite applications. This paper focuses on modeling resin flow in a deforming fiber tow during an automated process of partially impregnated thermoset prepreg composite material tapes. In this work, a tow unit cell based model has been presented that determines the consolidation and impregnation of a thermoset prepreg tape under an input pressure profile. A parametric study has been performed to characterize the behavior of varying tow speed and compaction forces on the degree of consolidation. Results indicate that increased tow consolidation is achieved with slower tow speeds and higher compaction forces although the relationship is not linear. The overall modeling of this project is motivated to address optimization of the 'green state' composite properties and processing parameters to reduce or eliminate 'cured state' defects, such as porosity and de-lamination. This work is partially funded by the Department of Energy under Award number DE-EE0001367.

36 MATERIALS SCIENCE↗

A Model for Tow Impregnation and Consolidation for Partially Impregnated Thermoset Prepregs

The formation and transport of voids in composite materials remains a key research area in composite manufacturing science. Knowledge of how voids, resin, and fiber reinforcement propagate throughout a composite material continuum from green state to cured state during an automated tape layup process is key to minimizing defects induced by void-initiated stress concentrations under applied loads for a wide variety of composite applications. This paper focuses on modeling resin flow in a deforming fiber tow during an automated process of partially impregnated thermoset prepreg composite material tapes. In this work, a tow unit cell based model has been presented that determines the consolidation and impregnation of a thermoset prepreg tape under an input pressure profile. A parametric study has been performed to characterize the behavior of varying tow speed and compaction forces on the degree of consolidation. Results indicate that increased tow consolidation is achieved with slower tow speeds and higher compaction forces although the relationship is not linear. The overall modeling of this project is motivated to address optimization of the 'green state' composite properties and processing parameters to reduce or eliminate 'cured state' defects, such as porosity and de-lamination. This work is partially funded by the Department of Energy under Award number DE-EE0001367.

36 MATERIALS SCIENCE↗

Critical transverse compressive stresses of straight and bent CORC® wires with and without impregnation

CORC® wires are a promising superconductor for accelerator magnet applications. While their excellent uniaxial tensile properties have been well established, potential degradation under transverse compression remains a concern for accelerator magnets, in which transverse compression is a primary stress experienced by superconductors. To evaluate the critical transverse compressive stresses of rare-earth barium copper oxide conductors, we developed an experimental system that enables testing of samples both with and without impregnation in liquid nitrogen. Furthermore, because bending strain induced during coil winding may influence the critical compressive response of CORC® wires, the apparatus was also modified to allow testing under the bending condition. In this study wires were tested for five configurations: (1) straight, non-impregnated, (2) bent, non-impregnated, (3) straight, Stycast 2850 FT-impregnated, (4) bent, Stycast 2850 FT-impregnated, and (5) bent, paraffin wax-impregnated. The transverse pressures corresponding to 3% and 5% reductions in the critical current are reported. In conclusion, the effects of wire bending and impregnation on the critical transverse pressure are analyzed, and the implications for transverse stress levels in accelerator magnet conductors are discussed.

CORC® wire↗

Stepwise impregnation of bimetallic catalysts for carbon nanotube synthesis

Supported bimetallic catalysts are widely used for carbon nanotube (CNT) synthesis, yet the effects of impregnation procedure remain underexplored. Here, we investigated how the sequence of metal impregnation affects CNT synthesis. We prepared cobalt-molybdenum (Co-Mo) bimetallic catalysts on alumina supports via co- and stepwise impregnation, then compared their CNT synthesis performance under identical conditions. Stepwise-impregnated catalysts exhibited higher carbon yields than those prepared by co-impregnation. Notably, impregnating Mo after Co achieved the highest yield despite the lowest BET surface area. Synchrotron X-ray diffraction and visible/UV-Raman spectroscopy revealed that only this catalyst contained Al 2 (MoO 4 ) 3 with a MoO 4 structure. X-ray photoelectron spectroscopy clarified the surface chemistry: the catalyst with the highest CNT productivity exposed Mo entirely as Mo 6+ in Al 2 (MoO 4 ) 3 and CoMoO 4 , whereas the others contained both Mo 4+ and Mo 6+ . The MoO x species like Al 2 (MoO 4 ) 3 is known to suppress Co sintering during CNT synthesis, delaying catalyst deactivation and enhancing the carbon yield. Moreover, an inverse relationship was observed between carbon yield and the CoMoO 4 content. This is attributed to the consumption of catalytically active Co during CoMoO 4 formation, which reduces active sites for CNT growth. ICP-OES further confirmed higher Co and Mo loadings for stepwise catalysts, contributing to superior catalyst performance. The extent of CoMoO 4 formation strongly depended on the metal introduction sequence. In conclusion, this trend is illustrated by considering the relationship between the point of zero charge of support and the pH of the metal precursor solutions.

36 MATERIALS SCIENCE↗

Silica-coated multi-walled carbon nanotubes impregnated with polyethyleneimine for carbon dioxide capture under the flue gas condition

In this study, silica-coated multi-walled carbon nanotubes impregnated with polyethyleneimine (PEI) were prepared via a two-step process: (i) hydrolysis of tetraethylorthosilicate onto multi-walled carbon nanotubes, and (ii) impregnation of PEI. The adsorption properties of CO{sub 2} were investigated using CO{sub 2} adsorption–desorption isotherms at 298 K and thermogravimetric analysis under the flue gas condition (15% CO{sub 2}/85% N{sub 2}). The results obtained in this study indicate that CO{sub 2} adsorption increases after impregnation of PEI. The increase in CO{sub 2} capture was attributed to the affinity between CO{sub 2} and the amine groups. CO{sub 2} adsorption–desorption experiments, which were repeated five times, also showed that the prepared adsorbents have excellent regeneration properties. - Graphical abstract: Fabrication and CO{sub 2} adsorption process of the S-MWCNTs impregnated with PEI. - Highlights: • Silica coated-MWCNT impregnated with PEI was synthesized. • Amine groups of PEI gave CO{sub 2} affinity sites on MWCNT surfaces. • The S-MWCNT/PEI(50) exhibited the highest CO{sub 2} adsorption capacity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

X-ray computed tomography of microstructure evolution during matrix impregnation and curing in unidirectional fiber beds

Microstructural evolution during axial impregnation and subsequent curing of a preceramic polymer in unidirectional ceramic fiber beds is studied using X-ray computed tomography. The principal goal is to identify connections between void locations, void sizes, local fiber bed porosity, fiber movement, and impregnation conditions. The degree of saturation after impregnation is found to increase with instantaneous capillary number. But, because of the need to create pathways for gas escape during curing, fiber beds with high saturation after impregnation show the largest reductions in saturation during curing. Notwithstanding, saturation after curing increases with instantaneous capillary number. Voids tend to form in the largest channels between fibers, where the local fiber bed porosity is high, during both impregnation and curing. Here, void formation is typically accompanied by fiber movement that increases both the local fiber bed porosity near voids and the overall non-uniformity in the fiber bed, as measured by local porosity entropy.

(A - Material) fibers↗

Pd-impregnated SYT/LDC composite as sulfur-tolerant anode for solid oxide fuel cells

An Sr 0.88 Y 0.08 TiO 3-δ (SYT)/ La 0.4 Ce 0.6 O 1.8 (LDC) composite impregnated with Pd was evaluated as a sulfur-tolerant anode for the La 0.8 Sr 0.2 Ga 0.83 Mg 0.17 O 3-δ (LSGM)-supported cells. The impregnation of Pd into the porous SYT/LDC anode was found to significantly enhance the anode performance. With the addition of 1.5 wt % Pd into the anode, the anodic overpotential was reduced to about half of the original value. The single cell with the Pd-impregnated SYT/LDC anode showed a maximum power density of 1006 and 577 mW/cm 2 at 850 and 800°C in dry H 2 , respectively, which was more than twice of that prior to impregnation. The Pd-impregnated composite anode exhibited good tolerance to sulfur, with essentially no decay in performance in H 2 containing up to 50 ppm H 2 S.

25 ENERGY STORAGE↗

A new ductile, tougher resin for impregnation of superconducting magnets

A major remaining challenge for Nb 3 Sn high field magnets is their training due to random temperature variations in the coils. The main objective of our research is to reduce or eliminate it by finding novel impregnation materials in replacement of the epoxies currently used. An organic olefin-based thermosetting dicyclopentadiene resin, C 10 H 12 , commercially available in Japan as TELENE® by RIMTEC, was used to impregnate a short Nb 3 Sn undulator coil developed by ANL and FNAL. This magnet reached short sample limit after only two quenches, compared with ∼100 when CTD-101K® was used. Ductility, i.e. the ability to accept large strains, and toughness were identified as key properties to achieve these results. In addition, we have been investigating whether mixing TELENE with high heat capacity ceramic powders such as Gd 2 O 3 , Gd 2 O 2 S, and HoCu 2 , increases the specific heat (C p ) of impregnated Nb3Sn superconducting magnets. The viscosity, heat capacity, thermal conductivity, and other physical properties of TELENE with high-C p powder fillers were measured in this study as a function of temperature and magnetic field. The TELENE-87 wt%Gd 2 O 2 S had a peak in C p between 4.3 K and 5.3 K at fields between 0 and 8 T. We have also investigated the effect on the mechanical properties of pure and mixed TELENE under 10 MGy of gamma ray irradiation at the Takasaki Advanced Radiation Research Institute in Takasaki, Japan. TELENE-87 wt%Gd 2 O 2 S exhibited exceptional radiation resistance. Impregnating an undulator coil with TELENE mixed with Gd 2 O 2 S powder will verify whether the coils' thermal stability further improves, or whether its low diffusivity will require engineering the material with high-thermal conductivity components. Short magnet training will lead to better magnet reliability, lower magnet margins, lower risk and substantial saving in accelerators' commissioning costs. Part of this study is supported by the U.S.-Japan Science and Technology Cooperation Program in high energy physics operated by MEXT in Japan and DOE in the U.S.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Visible light absorption of TiO{sub 2} materials impregnated with tungstophosphoric acid ethanol–aqueous solution at different pH values. Evidence about the formation of a surface complex between Keggin anion and TiO{sub 2} surfaces

Graphical abstract: - Highlights: • TPA impregnation on TiO{sub 2} particles was done at different initial pH values. • Powders characterization evidenced the possible existence of TPA–TiO{sub 2} complexes. • Keggin anion complexed on TiO{sub 2} would be responsible of visible light absorption. - Abstract: TiO{sub 2} particles prepared by the sol–gel method were impregnated at different pH values (1.0, 2.0, 5.0 and 10.0) with a water–ethanol solution (50% V/V) of tungstophosphoric acid (TPA) (0.012 M). Similar preparation was carried out to synthesize TiO{sub 2} impregnated with [WO{sub 4}]{sup 2−} (TiW). These materials were characterized by different techniques such as UV–vis diffuse reflectance spectroscopy (UV–vis DRS), magic angle spinning nuclear magnetic resonance of {sup 31}P ({sup 31}P MAS NMR), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), Fourier transform Raman spectroscopy (FT-Raman). Results revealed that TPA–TiO{sub 2} materials exhibit visible light absorption only when impregnation was done at pH 1.0 (TiTPA1) and 2.0 (TiTPA2). TiW powder did not show visible light absorption. XRD patterns show the presence of peaks at 2θ = 25.4° (1 0 1), 37.9° (0 0 4), 47.8° (2 0 0) and 54.3° associated to the anatase phase. Solid NMR, FT-IR and FT-Raman characterization showed that TiTPA1 and TiTPA2 samples contain Keggin ([PW{sub 12}O{sub 40}]{sup 3−}) and lacunary anions ([PW{sub 11}O{sub 39}]{sup 7−}) respectively. On the other hand, FT-Raman results revealed a blue shifting and broadening of the band at 141 cm{sup −1} corresponding to anatase TiO{sub 2} and moreover, a broadening of bands at 900–1100 cm{sup −1} attributed to Keggin structures of TPA. Both spectral changes could be related to the formation of a surface complex between the Keggin anion of TPA and TiO{sub 2} surfaces. This interaction should be responsible for visible light absorption.

36 MATERIALS SCIENCE↗

Bio-inspired surfactant assisted nano-catalyst impregnation of Solid-Oxide Fuel Cell (SOFC) electrodes

A bio-inspired surfactant was utilized to assist in the efficient impregnation of a nano-CeO₂ catalyst throughout both porous Solid Oxide Fuel Cells (SOFC’s) electrodes simultaneously. The process included the initial modification of electrode pore walls with a polydopamine film. The cell was then submersed into a cerium salt solution. The amount of nano-CeO₂ deposited per impregnation step increased by 3.5 times by utilizing this two-step protocol in comparison to a conventional drip impregnation method. The impregnated cells exhibited a 20% higher power density than a baseline cell without the nano-catalyst at 750°C (using humid H₂ fuel).

25 ENERGY STORAGE↗

Microfluidic Sensors with Impregnated Fluorophores for Simultaneous Imaging of Spatial Structure and Chemical Oxygen Gradients

Inside surfaces of polystyrene microfluidic structures were impregnated with the oxygen sensing dye (PtTFPP) using a solvent-induced fluorophore impregnation (SIFI) method. By this technique, microfluidic oxygen sensors are obtained that enable simultaneous imaging of both chemical oxygen gradients and the physical structure of the microfluidic interior. A gentle method of fluorophore impregnation using acetonitrile solutions of PtTFPP at 50oC was developed leading to 10 micron deep region containing fluorophore. This region is localized at the surface to sense oxygen in the interior fluid during use. Regions of the device that do not contact the interior fluid pathways lack fluorophores and are dark in fluorescent imaging. The technique was demonstrated on straight microchannel and pore network devices, the latter having pillars of 300 µm diameter spaced center to center at 340 µm providing pore throats of 40 µm. Sensing within channels or pores, and imaging across the pore network devices were performed using a Lambert LIFA-P frequency domain fluorescence lifetime imaging system on a Leical microscope platform. Calibrations of different devices prepared by the SIFI method were indistinguishable. Gradient imaging showed fluorescent regions corresponding to the fluid pore network, dark pillars, and fluorescent lifetime varying across the gradient, thus providing both physical and chemical imaging. More generally, the SIFI technique can impregnate the interior surfaces of other polystyrene containers, such as cuvettes or cell and tissue culture containers, to enable sensing interior conditions.

microfluidic, sensor, imaging, oxygen↗

Fabrication of Impregnated-Electrode-Type Polyatomic Ion Source with Ionic Liquid

Three types of ionic liquid ion source characterized by needle-type, capillary-needle-type and impregnated-electrode-type emitters were fabricated and demonstrated. The ion emission of a pure ionic liquid was demonstrated for the capillary-needle- and impregnated-electrode-type emitters. The emission stability of the impregnated-electrode-type emitter is currently insufficient for the shallow implantation of carbon due to occasional discharge. However, the impregnated-electrode-type emitter showed the largest emission current of 14 {mu}A at 6 kV among these emitters. This was considered to be caused by the relatively high feedability of the ionic liquid obtained from the emitter tip made of porous copper.

43 PARTICLE ACCELERATORS↗

Enhanced Bioconversion in Herbaceous Feedstocks from Impregnation of Co-Catalytic Lewis Acid and Deacetylation and Mechanical Refining

Improvements in conversion processes are needed to further reduce process complexity, biorefinery capital and operating (CAPEX/OPEX) costs, lower enzyme usage. Previous work has demonstrated that deacetylation and mechanical refining (DMR) process effectively deconstructs herbaceous biomass while producing highly digestible lignocellulosic slurries, with high titers of monomeric sugars, at reduced enzyme loadings (Poster 553 Chen at al,). We evaluated a co-catalytic approach using three Lewis acids: Fe+2, Fe+3, and Al+3, in sulfate form, at 1 mM, 5 mM and 10 mM concentrations. Lewis acids were impregnated into corn stover, followed by deacetylation with NaOH, and mechanically refined, prior to enzymatic hydrolysis (EH). Lower concentrations of Lewis acid positively impacted EH yield, increasing concentration lowered EH yield. Likewise Lewis acid treatment was more effective when combined with deacetylation than with deacetylation or Lewis acid treatment, alone. Comparing the effectiveness of the three Lewis acids identified ferrous iron more effective than ferric or aluminum (Fe+2 > Fe+3> Al+3) sulfate. Enzymatic hydrolysis sugar (glucose and xylose) concentration was higher 8% and 13%, respectively, in Fe2+ impregnated corn stover compared to the control. Refining energy required for PFI milling was reduced by ~25% with Fe+2 impregnation. However, treatment with Fenton treatment of the Fe2+ impregnated, deacetylated and PFI milled corn stover resulted in lower yields. for monomeric glucose and xylose due to non-specific degradation of carbohydrates and lignin.

09 BIOMASS FUELS↗