Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “III-V semiconductor materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

SolAero 2020: III-V Metamorphic Graded Buffers (CRADA Final Report)

The effort by the National Renewable Energy Laboratory (NREL) for SolAero Technologies Corp (SolAero) will involve helping with four tasks: 1) Supporting the development, characterization, and optimization of metamorphic grades in III-V multi-junction solar cells, 2) Doping of III-V semiconductor materials and junctions, and 3) Incorporating strain balanced layers into solar cells, and 4) high efficiency germanium based solar cells.

14 SOLAR ENERGY↗
DOE OSTI2024

Lithography-Free Mesa Isolation of III–V Solar Cells Through Laser Ablation

Eliminating photolithography from solar cell processing is a significant opportunity for cost reduction for III-V solar cells. Here, in this work, we explore femtosecond laser ablation as an alternative to contact photolithography and wet chemical etching for mesa isolation. We demonstrate both GaAs and GaInP solar cells mesa-isolated by femtosecond laser ablation with minimal to no loss in solar cell performance. We show the best results with a 400 fs UV pulsed laser and a short clean-up etch that also serves as a contact layer removal etch.

14 SOLAR ENERGY↗
DOE OSTI2026

Lithography-Free Mesa Isolation by Laser Ablation for Multijunction III-V Photovoltaic Space Power Generation

Eliminating photolithography from photovoltaic device processing is a significant opportunity for cost reduction and increased manufacturing throughput. In this work, we test femtosecond laser ablation and scribing as an alternative to contact photolithography and wet chemical etching for mesa isolation of multijunction devices. We demonstrate that upright multijunction devices isolated by using the laser as a scribe to cleave through the substrate had virtually no performance loss when compared to a baseline device processed with photolithography. By contrast, devices isolated by laser ablating through the active layers have performance losses that cannot be fully eliminated with postprocess etching. This demonstration of photolithography-free mesa isolation with no performance losses is promising as a pathway to less expensive and higher throughput III-V device manufacturing.

14 SOLAR ENERGY↗
DOE OSTI2025

Deep-learning atomistic semi-empirical pseudopotential model for nanomaterials

The semi-empirical pseudopotential method (SEPM) has been widely applied to provide computational insights into the electronic structure, photophysics, and charge carrier dynamics of nanoscale materials. We present “DeepPseudopot”, a machine-learned atomistic pseudopotential model that extends the SEPM framework by combining a flexible neural network representation of the local pseudopotential with parameterized non-local and spin-orbit coupling terms. Trained on bulk quasiparticle band structures and deformation potentials from GW calculations, the model captures many-body and relativistic effects with very high accuracy across diverse semiconducting materials, as illustrated for silicon and group III-V semiconductors. DeepPseudopot’s accuracy, efficiency, and transferability make it well-suited for data-driven in silico design and discovery of novel optoelectronic nanomaterials.

Lin, Kailai [University of California, Berkeley, C↗
DOE OSTI2024

Self-consistent quasiparticle G W and hybrid functional calculations for Al/InAs/Al heterojunctions: Band offset and spin-orbit coupling effects

The electronic structure of surfaces and interfaces plays a key role in the properties of quantum devices. Here, we study the electronic structure of realistic Al/InAs/Al heterojunctions using a combination of density functional theory with hybrid functionals and state-of-the-art quasiparticle G W (QSGW) calculations. We find a good agreement between QSGW calculations and hybrid functional calculations, which themselves compare favorably well with angle-resolved photoemission spectroscopy experiments. Our paper confirms the need for well-controlled quality of the interfaces to obtain the needed properties of InAs/Al heterojunctions. A detailed analysis of the effects of spin-orbit coupling on the spin splitting of the electronic states shows a linear scaling in k space, related to the two-dimensional nature of some interface states. The good agreement by QSGW and hybrid functional calculations opens the door towards trustable use of an effective approximation to QSGW for studying very large heterojunctions. Published by the American Physical Society 2024

36 MATERIALS SCIENCE↗
DOE OSTI2025

Halide Vapor Phase Epitaxy of Ge from an Elemental Source

Halide vapor phase epitaxy shows promise for low-cost photovoltaic device manufacturing because of its high growth rates and lower cost elemental precursors but previously has not been used to deposit epitaxial Ge. Here, we demonstrate Ge deposition by generating GeCl 2 in situ from solid Ge and HCl in a N 2 ambient. To achieve Ge growth, we inject AsH 3 and PH 3 as sources of active hydrogen to the growth surface to create a driving force for growth. We do not observe Ge growth unless a supply of hydrogen is added, consistent with thermodynamic calculations. Furthermore, we show the hydrogen source must crack readily on the substrate surface to enable growth; relatively stable sources such as H 2 do not cause growth. Unintentional group V doping is one drawback of using AsH 3 and PH 3 to drive the Ge reaction. We observed As or P concentrations in the Ge films ranging from 4 x 10 17 to 1 x 10 18 atoms/cm 3 , concentrations that can drastically influence device characteristics. However, we note there are numerous other "helper molecule" options that can provide active hydrogen without doping or etching the material. This work provides a path forward for Ge deposition for optoelectronic devices from an elemental source.

14 SOLAR ENERGY↗
DOE OSTI2025

Models and Measurements Quantify Photon Recycling, Charge-Carrier Diffusion and Photon Scattering Contributions to Photoluminescence in InP Nanowire Arrays

Nanowire arrays present many unique advantages for solar-to-chemical energy conversion. One possible advantage is that photon recycling between neighboring nanowires has the potential to increase solar energy conversion efficiencies. Here, in this work, we explore three underlying mechanisms of optical and electronic coupling between neighboring nanowires─incident photon scattering, photon recycling, and charge-carrier transport from the photoexcited nanowire to the neighboring nanowire via the underlying substrate─using single nanowire-level microscopy and spectroscopy measurements. We present a comprehensive analysis of light absorption and emission of a single nanowire at open circuit, and subsequent re-absorption and re-emission by a neighboring nanowire. We developed a novel correlated single nanowire microspectroscopy and widefield imaging methodology to spatially resolve photon communication pathways between neighboring nanowires and selectively image re-emitted and reflected photons. We developed unique multiphysics models to couple wave optics and semiconductor photophysics to especially isolate contributions from photon recycling and electronic transport to photon emission from neighboring nanowires. By systematically varying the morphologies of the nanowires modeled, we identified pathways to maximize photon recycling between neighboring nanowires. We concluded that the measured photoluminescence is more strongly influenced by the diffusion of charge carriers as compared to photon recycling in materials with moderate-to-large charge-carrier mobilities (>10 cm 2 V –1 s –1 ), and that photon recycling dictates photoluminescence intensity only when the charge-carrier mobility is low (<1 cm 2 V –1 s –1 ). The experimental and simulation platforms developed herein for photon management strategies can be leveraged by the semiconductor photocatalysis community to enhance solar-to-chemical conversion efficiencies in semiconductor nanowire arrays.

25 ENERGY STORAGE↗
DOE OSTI2025

Near-half-metallic state in the half-Heusler PtMnSb film on a III-V substrate

The interplay between half-metallic ferromagnetism and spin-orbit coupling within the inversion-symmetry-broken structure of half Heuslers provides an ideal platform for various spintronics functionalities. Taking advantage of good lattice matching, it is highly desired to epitaxially integrate promising Heuslers into III-V semiconductor-based devices. PtMnSb is one of the first half Heuslers predicted to be an above-room-temperature half-metal with large spin orbit coupling, however, its half-metallicity and potential as a spintronics material has remained elusive due to lack of high quality samples. Here, in this study, we demonstrate epitaxial growth of single crystal PtMnSb(001) film on GaSb(001) substrates using molecular beam epitaxy. Direct observation of the band structure via angle-resolved photoemission spectroscopy and many-body perturbation theory within the quasi-particle self-consistent GW approximation (QPGW) reveal that PtMnSb hosts rather a near-half-metallic state with both spin bands crossing the Fermi level and with high spin polarization over 90%. Temperature dependence of magnetization also shows an anomalous enhancement below 60 K, which can be associated with the development of such a near-half-metallic state at low temperatures. Epitaxial growth of high crystalline PtMnSb on a III-V paves the way for systematic clarification of its spin transport properties with fine-tuning of strain in heterostructure devices.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Modeling neutral defects in III-V ternary alloys with a special quasirandom structure: Analysis of As- and III-site point defects in InGaAs

While first-principles density functional theory modeling has become a vital tool to investigate defect properties in semiconductors, the lack of crystalline periodicity in pseudobinary random composition alloys, such as In 1−𝑥 ⁢Ga 𝑥 ⁢As, complicates such analyses. We present a simulation strategy to systematically take into account the variability in the local defect environment in order to predict statistical properties of neutral intrinsic defects in In 1−𝑥⁢ Ga 𝑥 ⁢As. We use a comprehensive sampling from a modest-sized 64-atom special quasirandom structure (SQS) to define a statistically representative set of defects, and use a 512-atom hypercell, a 2 × 2 × 2 supercell of SQS supercells, to achieve cell-size convergence. We articulate an equivalent site principle and describe how it constrains atomic chemical reference energies in computation of defect formation energies in pseudobinary alloys. A simple protocol for estimating reference energies for the Ga and In atoms sharing the III site succeeds in obtaining the equivalence of defects at Ga-sites and In sites in the SQS supercell, (<30 meV differences in average formation energies). For III-site defects, such as the As antisite As III , the statistical variability in formation energies is modest, ≈ 0.1–0.2 eV. The variability in formation energy at As-site defects, such as the As vacancy 𝑣 As , can be much larger, >1 eV. The As antisite is shown to be a low-energy defect and the most likely to be present in as-grown materials, just as in GaAs. All other defects are higher-energy defects unlikely to be important in native material, but potentially important in radiation-damaged material. With a strong variability in defect energies, especially on the As-site, explicit consideration of statistical variability due to compositional randomness will be imperative for meaningful and quantitative comparisons to experiment.

Density functional theory↗
DOE OSTI2025

Trap-assisted Auger-Meitner recombination in GaN p-i-n diodes

Most properties of semiconductor devices are dominated by shallow impurities. However, deep defects often play an important role, for instance, in recombination processes or high field transport. While a variety of techniques are available to assess the density and energy levels of impurities, other properties, such as the recombination mechanisms of the defects, escape observation. We report on the direct measurement of hot electrons generated by trap-assisted Auger-Meitner recombination (TAAR) in GaN p-i-n diodes. By performing electron emission spectroscopy (EES) on diodes with surfaces activated to negative electron affinity by cesium, we observe the expected overflow electrons of p-i-n diodes under low current injection. However, when operating the devices at higher current densities, as low as ∼25 A/c⁢m 2 , we measure the emission of high-energy electrons. At variance with the observed hot electrons in light-emitting diodes (LEDs) using EES, the hot electrons generated in p-i-n diodes at our tested currents cannot be from eeh Auger-Meitner recombination due to the diodes' significantly lower carrier densities compared to those in LEDs. During our measurements, we observe the emission of accumulated electrons with energies ∼0.42 eV, ∼0.99 eV, ∼1.43 eV, and ∼2.32 eV above the conduction-band minimum (CBM) at various bias conditions, suggesting the existence of conduction-band features in GaN at these energies where electrons can be long-lived, such as satellite-valley minima and inflection points. We also measure incompletely relaxed hot electrons approaching energies 1.97 ± 0.13 eV and 2.94 ± 0.13 eV above the CBM, as the diodes are biased to high currents, suggesting at least some of the TAAR partaking defects have an energy level ≳1.97 eV and ≳2.94 eV away from either the conduction or valence band edges. Additionally, at our highest operating currents, we measure hot electrons with energies 3.28 ± 0.13 eV above the CBM, providing direct evidence of TAAR processes involving shallow impurities. This unexpected observation of TAAR in GaN p-i-n diodes spotlights the importance of further studies of defects in GaN and the necessity to incorporate the multi-phonon emission, radiative, and TAAR capture steps of defect-assisted recombination cycles into device modeling. Furthermore, this experiment demonstrates the applicability of the simplest semiconductor structures, p-i-n diodes, as a test bed to study the rich recombination physics of semiconductor materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Planarizing Spalled GaAs(100) Surfaces by MOVPE Growth

III-V photovoltaic devices have demonstrated exceptional performance across various applications, with controlled crystal fracturing, known as controlled spalling, emerging as a promising method to reduce costs by enabling substrate reuse. Spalling GaAs(100) substrates, a commonly used substrate in III-V photovoltaics, results in faceted ridges that must be planarized to grow high-quality photovoltaic devices. Here, in this study, we demonstrate that a GaAs(100) wafer offcut toward [$0\bar{11}$] and spalled toward [$011$] can be efficiently planarized by growing C:GaAs by metal-organic vapor phase epitaxy (MOVPE) on the surface, with up to 95% of the nominally deposited material used to fill the valleys between ridges. We find that reducing the offcut to 2° enhances the planarizing capability of C:GaAs. A surface morphology model indicates that the density of surface dangling bonds significantly influences the growth evolution of undoped GaAs surfaces. In contrast, the model suggests that the effectiveness of C:GaAs as a smoothing layer stems from modifying the atomic surface structure and, consequently, the associated sticking coefficients of the facets, which can alter the evolution of surface morphology. Our findings provide guidelines for the epitaxial planarization of semiconductor surfaces and improve the understanding of MOVPE growth on nonplanar surfaces.

14 SOLAR ENERGY↗
DOE OSTI2024

Reductive pathways in molten inorganic salts enable colloidal synthesis of III-V semiconductor nanocrystals

Colloidal quantum dots, with their size-tunable optoelectronic properties and scalable synthesis, enable applications in which inexpensive high-performance semiconductors are needed. Synthesis science breakthroughs have been key to the realization of quantum dot technologies, but important group III-group V semiconductors, including colloidal gallium arsenide (GaAs), still cannot be synthesized with existing approaches. The high-temperature molten salt colloidal synthesis introduced in this work enables the preparation of previously intractable colloidal materials. We directly nucleated and grew colloidal quantum dots in molten inorganic salts by harnessing molten salt redox chemistry and using surfactant additives for nanocrystal shape control. Synthesis temperatures above 425°C are critical for realizing photoluminescent GaAs quantum dots, which emphasizes the importance of high temperatures enabled by molten salt solvents. We generalize the methodology and demonstrate nearly a dozen III-V solid-solution nanocrystal compositions that have not been previously reported.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Metamorphic Epitaxy Solutions for Thermophotovoltaic and Laser Power Conversion Applications

Metamorphic GaInAs enables photovoltaic devices optimized for a wide range of bandgaps between 0.35 and 1.41 eV. We have developed compositionally graded buffers made of GaInP and AlGaInAs to enable growth of these devices on GaAs substrates with low dislocation densities and high performance. We present results for devices grown on both graded buffer materials with device bandgaps in the range 0.58-1.41 eV and compare the benefits and drawbacks of each material system. These results enable high performance for applications such as thermophotovoltaics and optical power transmission using high power lasers.

III-V↗
DOE OSTI2025

Atoms-to-devices models for post-irradiation annealing kinetics in III-V semiconductors

Understanding atomic displacement damage and propagating this understanding into validated defect-aware radiation damage models is a critical step toward achieving predictive, atoms-to-systems assessment of radiation vulnerabilities of microelectronics. These models are essential for evaluating the performance and reliability of nuclear stockpile components or space-based electronics (satellites). The goal of this project was to bridge a fundamental science gap between defect spectroscopies and atomistic modeling of radiation-induced defects on the one hand, and simulations of device response on the other hand, to develop predictive defect-aware damage models for high-fidelity device simulations of radiation-damaged III-V semiconductors.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Correlated X‐Ray and Electron Microscopies of a Single Biphasic GaAs Nanowire

Engineering the properties of semiconductors by changing their crystalline phase is a technologically and economically relevant alternative to doping using foreign elements, with strong potential for photonic and electronic applications. Although major advances have been reported recently for crystal‐phase engineering of III‐V and group IV semiconductor nanowires, interfacing two mismatched crystalline phases in a nanostructure induces several deformation mechanisms, which remain largely unexplored. Here, using state‐of‐the‐art synchrotron X‐ray nanobeam diffraction and transmission electron microscopy, subtle twisting and bending is unveiled within an individual GaAs nanowire containing cubic and hexagonal segments. Their role is discussed in accommodating the inter‐reticular spacing fluctuations, and their variations are correlated to the nanoscale phase distribution and to the effect of the NW support. This study brings direct evidence of a complex combination of deformation mechanisms in biphasic nanowires, which opens a new path to tune the nanowire properties with appealing perspectives for device engineering in nanophotonics and nanomechanics.

III-V semiconductors↗
DOE OSTI2026

Photoelectrode Durability in Two- versus Three-Electrode Configurations: Understanding the Impact of Circuit Configuration on Water-Splitting Stability

Device durability remains a significant challenge in photoelectrochemical (PEC) water splitting under ambient conditions. Yet, a lack of understanding of the test configuration and applied bias effects continue to hinder progress. In this study, we differentiate two-electrode (2E) and three-electrode (3E) configurations for evaluating PEC material durability, focusing particularly on their impacts on photoabsorber solid-state operating conditions. Our results underscore the fallacy of inferring 2E device stability from durability measurements performed solely in 3E configurations. Unmeasured and often misunderstood total circuit bias in 3E tests moderates material degradation, leading to the overestimation of photoelectrode stability compared to short-circuit operation. We demonstrate how the photoabsorber's operating voltage critically governs charge separation, surface stability, and degradation mechanisms during PEC operation. With these findings, we propose a standardized framework for conducting more reliable 3E durability experiments that simulate unassisted performance to help accelerate the development of robust, stable materials for solar-driven water splitting.

08 HYDROGEN↗
DOE OSTI2026

Nickel Interlayer for Improved Silver Complex Inks Metallization in GaAs Photovoltaic Devices

Large areas of III-V photovoltaic panels are essential to supplying operational energy for a growing demand of satellites of strategic importance to the United States military, covering a range of applications. High fabrication costs and low manufacturing throughput are key barriers to meeting the necessary supply, which can in turn jeopardize mission success. At the device level, metallization based on printing of complex metal inks has attracted significant research interest due to its potential to substantially reduce processing costs and increase throughput while achieving electrical performance comparable to those of conventional metallization schemes. For GaAs photovoltaic devices, however, reliable electrical contacting remains challenging due to the formation of an interfacial oxide layer at the metal-semiconductor interface. This oxide barrier severely limits current extraction from the PV absorber, resulting in unacceptably high contact resistance. In this study, we report the introduction of a reactive nickel (Ni) interfacial layer between the silver metal fingers and the GaAs substrate to suppress oxide formation while maintaining a low-resistance electrical interface, and show performance data from fully fabricated GaAs devices incorporating the Ni interlayer. These results demonstrate the potential of reactive Ni ink as an effective interfacial layer for improved electrical contacting in low-cost PV metallization schemes.

14 SOLAR ENERGY↗
DOE OSTI2025

Semiconductor-compatible topological digital alloys

Recently, GeSn alloys have attracted much interest for direct-gap infrared photonics and as potential topological materials which are compatible with the semiconductor industry. However, for photonics, the high-Sn content required leads to low detectivity, associated with poor material quality, and the (>35 %) Sn required for topological properties have been out of reach experimentally. Here, we demonstrate that by patterning the Sn distribution within Ge, the electronic properties have a far greater tunability than is possible with the random alloy. For the GeSn δ-digital alloy (DA) formed by confining Sn atoms in atomic layer(s) along the [111] direction of Ge, we show that ∼ 10 % Sn can lead to a triple-point semimetal. These findings are understood in terms of Sn ordering causing spatial separation of Sn and Ge band edges, leading to band inversion. This mechanism can also lead to a weak topological insulator, Weyl semimetal, and enables tunable direct bandgaps down to 2 meV, covering the entire infrared range. This DA induced topological properties are also identified in compound semiconductors, such as InAs 1-x Sb x , showing the general applicability of the DA design for realizing topological properties on conventional semiconductor platforms. Furthermore, our findings not only point to a new class of currently unexplored topological systems accessible by epitaxy, but also establish the promise of low-Sn GeSn DAs for application as infrared laser diodes and photodetectors in Si photonic integrated circuits and infrared image sensors.

3D topological semimetal↗