Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Helicon waves”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

17 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

First Demonstration of Resonant Pitch-Angle Scattering of Relativistic Electrons by Externally Launched Helicon Waves

Helicon waves (a.k.a whistler waves) satisfying the normal wave-particle cyclotron resonance are observed to limit the growth and maximum energy of relativistic electrons (REs) in low-density Ohmic DIII-D tokamak plasmas. Following the application of helicon waves, pitch-angle scattering of high-energy REs causes an increase in both synchrotron and electron-cyclotron emissions. The hard x-ray emission, a proxy for the RE population, ceases to grow. Energy-resolved hard x-ray measurements also show a striking decrease in the number of high-energy REs (above the resonance at approximately 8MeV) to below the noise floor and an increase in low-energy (∼ 4 MeV) REs. This occurs despite the toroidal electric field remaining high enough to drive exponential RE growth in the absence of helicon waves. Furthermore, these results open new directions for limiting the maximum energy of RE populations in laboratory and fusion plasmas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2003

Helicon Wave Physics Impacts on Electrodeless Thruster Design

Effective generation of helicon waves for high density plasma sources is determined by the dispersion relation and plasma power balance. Helicon wave plasma sources inherently require an applied magnetic field of .01-0.1 T, an antenna properly designed to couple to the helicon wave in the plasma, and an rf power source in the 10-100 s of MHz, depending on propellant choice. For a plasma thruster, particularly one with a high specific impulse (>2000 s), the physics of the discharge would also have to address the use of electron cyclotron resonance (ECR) heating and magnetic expansion. In all cases the system design includes an optimized magnetic field coil, plasma source chamber, and antenna. A preliminary analysis of such a system, calling on experimental data where applicable and calculations where required, has been initiated at Glenn Research Center. Analysis results showing the mass scaling of various components as well as thruster performance projections and their impact on thruster size are discussed.

Gilland, James↗
NASA NTRS2007

Helicon Wave Physics Impacts on Electrodeless Thruster Design

Effective generation of helicon waves for high density plasma sources is determined by the dispersion relation and plasma power balance. Helicon wave plasma sources inherently require an applied magnetic field of .01-0.1 T, an antenna properly designed to couple to the helicon wave in the plasma, and an rf power source in the 10-100 s of MHz, depending on propellant choice. For a plasma thruster, particularly one with a high specific impulse (>2000 s), the physics of the discharge would also have to address the use of electron cyclotron resonance (ECR) heating and magnetic expansion. In all cases the system design includes an optimized magnetic field coil, plasma source chamber, and antenna. A preliminary analysis of such a system, calling on experimental data where applicable and calculations where required, has been initiated at Glenn Research Center. Analysis results showing the mass scaling of various components as well as thruster performance projections and their impact on thruster size are discussed.

Gilland, James H.↗
DOE OSTI2026

Effects of density turbulence on helicon wave propagation in the core plasmas

Radio frequency wave propagation can be significantly affected by density irregularities, such as filaments in the scrape-off layer or instabilities in the core plasma. In this study, we examine the impact of edge turbulence on helicon wave propagation using the Petra-M simulation tool. To analyze the effect of edge turbulence, we utilize a realistic background plasma derived from XGC simulations, which includes spatial density fluctuations at the edge. This focus is particularly relevant for the DIII-D configuration, characterized by edge density turbulence of the core plasmas in a wide pedestal QH-mode. We focus on helicon wave propagation in the core plasma since the slow mode cannot propagate into the core plasma when the density is higher than the lower hybrid resonance, where a wide pedestal QH-mode occurs. The simulation results indicate that edge density fluctuations have a substantial impact on helicon wave coupling due to scattering in the core. We specifically demonstrate that the toroidal mode number and the level of density fluctuations are significant factors influencing scattering. While we have minimized the excitation of slow modes from the antenna, we still observe mode-converted slow modes resulting from the incoming helicon waves. The insights derived from these simulations will inform upcoming tokamak experiments regarding helicon antenna coupling in long pulse scenarios.

Kim, Eun-Hwa [Princeton Plasma Physics Laboratory ↗
DOE OSTI2025

Real-time steerable frequency-stepped Doppler backscattering (DBS) system for local helicon wave electric field measurements on the DIII-D tokamak

A new frequency-stepped Doppler backscattering (DBS) system has been integrated into a real-time steerable electron cyclotron heating launcher system to simultaneously probe local background turbulence (f < 10 MHz) and high-frequency (20–550 MHz) density fluctuations in the DIII-D tokamak. The launcher allows for 2D steering (horizontally and vertically) over wide angular ranges to optimize probe location and wavenumber response. The vertical steering can be optimized during a discharge in real time. The new DBS system employs a programmable frequency synthesizer with adjustable dwell time as a source to launch either O or X-mode polarized millimeter waves. This system can step in real-time over the entire E-band frequency range (60–90 GHz). This combination of capabilities allows for the diagnosis of the complex internal spatial structure of high power (>200 kW) helicon waves (476 MHz) injected from an external antenna during helicon current drive experiments in DIII-D. Broadband density fluctuations around the helicon frequency are observed during real-time scans of measurement location and wavenumber during these experiments. Analysis indicates that these broadband high-frequency fluctuations are a result of backscattering of the DBS millimeter-wave probe beam from plasma turbulence modulated by the helicon wave. It is observed that background turbulence is effectively locally “tagged” with the helicon wave electric field, forming images of the turbulent spectrum in the overall density fluctuation spectrum that appear as high-frequency sidebands of the turbulence. These observations of background turbulence and high-frequency fluctuations open up the possibility of monitoring local helicon wave amplitude by comparing the high-frequency signal amplitude to the simultaneously measured background turbulence. In combination with the real-time measurement location and wavenumber scanning capabilities (offered by real-time frequency-stepping and steering), this allows rapid determination of the spatial distribution of the helicon wave power during steady-state plasma operation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1972

An impedance analysis of double-stream interaction in semiconductors

The electromagnetic waves propagating through a drifting semiconductor plasma are studied from a macroscopic point of view in terms of double-stream interaction. The possible existing waves (helicon waves, longitudinal waves, ordinary waves, and pseudolongitudinal waves) which depend upon the orientation of the dc external magnetic field are derived. A powerful impedance concept is introduced to investigate the wave behavior of longitudinal (space charge) waves or pseudolongitudinal waves in a semiconductor plasma. The impedances due to one- and two-carrier stream interactions were calculated theoretically.

Chen, P. W.↗
DOE OSTI2024

Full-wave simulations on helicon and parasitic excitation of slow waves near the edge plasma

Helicon waves are thought to be promising in various tokamaks, such as DIII-D, because they can penetrate reactor-grade high-density cores and drive the off-axis current with higher efficiency. In the frequency regime ~476 MHz, both slow electrostatic and fast electromagnetic helicon waves can coexist in DIII-D. If the antenna parasitically excites the slow mode, these waves can propagate along the magnetic field line into the scrape-off layer (SOL). Although the importance of the misalignment of the Faraday screen and the electron density in the SOL on the excitation and propagation of slow modes is well known, the conditions for minimizing slow mode excitation have yet to be optimized. Using the Petra-M simulation code in the 2D domain, we analyze the effects of the misalignment of the antenna in the poloidal direction, the misalignment of the Faraday screen in the toroidal direction, and the density in front of the antenna on slow mode generation. Our results suggest that the misalignment of the Faraday screen is a critical factor in reducing the slow mode and that the misalignment angle should be below ~5° to minimize the slow wave excitation. When the electron density is higher than 3.5 x 10 18 m –3 in the SOL, the generation of the slow mode from the antenna is minimized and unaffected by the misalignment of the Faraday screen.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Analysis of runaway electron driven whistler wave instability experiments

Data acquired on the DIII-D tokamak were analyzed. The data are from experiments that were conducted to study an instability that is driven unstable by intense populations of electrons with MeV energies that are known as runaway electrons. The instability is a type of plasma wave called a whistler wave that occurs at frequencies above the ion cyclotron frequency but well below the electron cyclotron frequency. The waves were measured by magnetic fluctuation coils that are embedded in the DIII-D vacuum vessel wall. After upgrades to this diagnostic were completed, new experiments were conducted on July 13, 2020 in order to measure the toroidal mode number of the whistler waves and to extend the frequency of the detected waves. Through the use of mixers, instability between 600-700 MHz was detected. (The initial experiments only measured up to 200 MHz.) Analysis of the data was led by Hari Choudhury, a PhD student at Columbia University. Mr. Choudhury has submitted two papers for publication that include contributions by UC Irvine (UCI) Professor Heidbrink and his graduated PhD student Genevieve DeGrandchamp: “Detailed Characterization of Runaway Electron Driven Whistler Waves in Low-Density DIII-D Discharges” and “First Demonstration of Resonant Pitch-Angle Scattering of Relativistic Electrons by Externally-Launched Helicon Waves.” The first paper, which has been submitted to Physics of Plasmas, has significant contributions to both the data and the interpretation by UCI scientists. In contrast, UCI contributions to the second paper, which has been submitted to Physical Review Letters, are relatively minor.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Understanding carbon sourcing and transport originating from the helicon antenna surfaces during high-power helicon discharge in DIII-D Tokamak

The high-power helicon wave system in the DIII-D tokamak could potentially introduce new plasma–material interaction (PMI) challenges owing to rectified RF sheath potentials that develop near the antenna and surrounding plasma-facing components. We present the first application of the STRIPE (Simulated Transport of RF Impurity Production and Emission) framework to helicon-induced PMIs, extending previous STRIPE studies of ICRH antennas by incorporating net erosion, local re-deposition, and three-dimensional global impurity transport. The integrated workflow couples SOLPS, COMSOL, RustBCA, GITR, and GITRm to simulate carbon erosion, re-deposition, and impurity transport for two experimentally constrained DIII-D H-mode helicon operating scenarios with different antenna–plasma gaps, coupled RF powers, and edge plasma conditions. COMSOL predicts rectified RF sheath potentials of 1–5 kV localized near the lower portion of the antenna, where the magnetic field intersects the surface at grazing incidence. Carbon self-sputtering dominates the erosion source, whereas RF-accelerated D + ions contribute approximately 1% of the total gross erosion. The smaller-gap operating scenario exhibits substantially stronger gross erosion, enhanced local re-deposition (∼12%), and a larger confined carbon inventory owing to increased plasma accessibility and broader RF sheath coverage. Comparison with available DIII-D measurements shows no distinct change in the global carbon signal that correlates with the helicon RF pulse, consistent with the simulations indicating that the helicon-generated carbon source remains small compared with the existing background carbon inventory under the present graphite-wall operating conditions. These results demonstrate the capability of STRIPE to integrate RF sheath modeling, plasma transport, surface interaction physics, and three-dimensional impurity transport for the interpretation of helicon-induced PMIs. The study further identifies the principal sources of modeling uncertainty, including grazing-angle RF sheath physics, slow-wave resolution, plasma-background extrapolation, and trace-impurity transport assumptions, providing a framework for future validation and model development.

Kumar, Atul [Oak Ridge National Laboratory (ORNL),↗
DOE OSTI2026

FullWave — A Full Wave Parallel Code for Modeling RF Fields in Hot Tokamak Plasma

FullWave is a computer code that simulates how radio-frequency (RF) waves travel and deposit energy in the hot plasma inside a fusion reactor. RF waves are used to heat the plasma and drive electrical current, which is essential for sustaining fusion reactions. The code uses a new algorithm that can handle much finer spatial detail than previous codes — more than 100 times finer — while running efficiently on national supercomputers. It incorporates a detailed physics model that captures subtle kinetic effects important for accurate prediction of wave behavior. Under this project, FullWave was extended to cover multiple RF frequency ranges relevant to present and future tokamaks, and validated against experimental parameters from the DIII-D tokamak at General Atomics. Results were published in peer-reviewed journal articles.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Coherent mode and turbulence measurements with a fast camera

This study employs a fast camera with frame rates up to 900,000 fps to measure the transfer of energy across spatial scales in helicon source plasmas and during flux rope mergers and the measurement of azimuthal mode structures in helicon plasmas. By extracting pixel-scale dispersion relations and power spectral density (PSD) measurements, we measure the details of turbulent wave modes and energy distribution across a broad range of spatial scales within the plasma. We confirm the presence of drift waves in helicon plasmas, as well as the existence of strong dissipation regions in the PSD at electron skin depth scales for both helicon and flux rope merger experiments. This approach overcomes many limitations of conventional probes, providing high spatial and temporal resolution, without perturbing the plasma.

Instruments & Instrumentation↗
DOE OSTI2024

First high-power helicon results from DIII-D

Abstract More than 0.6 MW of rf power at 476 MHz has been coupled to DIII-D plasmas by launching helicon (whistler) waves with a traveling-wave antenna (comb-line) in the fast-wave polarization (Van Compernolle et al 2021 Nucl. Fusion 61 116034) which resulted in the observation of electron heating of the core plasma with single-pass absorption based on ray-tracing in L-mode discharges. The coupling performance of the 1.5 m wide 30-element comb-line traveling-wave antenna has been consistent with expectations based on the 2015–2016 experiments on DIII-D with a low-power 12-element prototype (Pinsker et al 2018 Nucl. Fusion 58 106007). The conditioning process that was necessary to carry out high-power experiments is discussed; rf-specific impurities have not been observed. Parametric decay instabilities have been observed and are being investigated as a potential edge absorption mechanism (Porkolab et al 2023 AIP Conf. Proc. 2984 070004).

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1993

Electron cyclotron thruster new modeling results preparation for initial experiments

The following topics are discussed: a whistler-based electron cyclotron resonance heating (ECRH) thruster; cross-field coupling in the helicon approximation; wave propagation; wave structure; plasma density; wave absorption; the electron distribution function; isothermal and adiabatic plasma flow; ECRH thruster modeling; a PIC code model; electron temperature; electron energy; and initial experimental tests. The discussion is presented in vugraph form.

Hooper, E. Bickford↗
NASA NTRS2000

Helicon Plasma Injector and Ion Cyclotron Acceleration Development in the VASIMR Experiment

In the Variable Specific Impulse Magnetoplasma Rocket (VASIMR) radio frequency (rf) waves both produce the plasma and then accelerate the ions. The plasma production is done by action of helicon waves. These waves are circular polarized waves in the direction of the electron gyromotion. The ion acceleration is performed by ion cyclotron resonant frequency (ICRF) acceleration. The Advanced Space Propulsion Laboratory (ASPL) is actively developing efficient helicon plasma production and ICRF acceleration. The VASIMR experimental device at the ASPL is called VX-10. It is configured to demonstrate the plasma production and acceleration at the 10kW level to support a space flight demonstration design. The VX-10 consists of three electromagnets integrated into a vacuum chamber that produce magnetic fields up to 0.5 Tesla. Magnetic field shaping is achieved by independent magnet current control and placement of the magnets. We have generated both helium and hydrogen high density (>10(exp 18) cu m) discharges with the helicon source. ICRF experiments are underway. This paper describes the VX-10 device, presents recent results and discusses future plans.

Squire, Jared P.↗
DOE OSTI2024

Data for "Propagation of EMIC Waves from Shabansky Orbits in the Dayside Magnetosphere"

Full-wave simulations of electromagnetic ion cyclotron waves in a non-dipole compressed magnetic field have been conducted using the Petra-M simulation code. The manuscript investigates the effect of misalignment of the Faraday screen and electron density in the scrape-off layer on the excitation and propagation of fast helicon and slow mode waves.

Magnetosphere: outer↗
DOE OSTI2025

Outlook for active plasma spectroscopy with entangled two-photon absorption

Entangled two-photon absorption (ETPA) exhibits a quantum-enhanced two-photon absorption cross-section and a linear scaling with incident power that exceeds classical two-photon absorption (TPA) at low photon flux. Here, we assess the feasibility and applications of ETPA for active plasma spectroscopy. The ETPA-absorbed power for an Ar + species in a helicon plasma scenario is calculated to be as high as 0.6 nW cm −1 along the incident beam path for nondegenerate-entangled photon pairs that are near-resonant with an intermediate level. The ETPA absorption power exceeds classical TPA and Bremsstrahlung emission, a necessary condition for a feasible fluorescence measurement. Applications of ETPA plasma spectroscopy may include trace impurity detection, ground-state excitation, and continuous-wave pumping for high-bandwidth turbulence measurements. Possible benefits of plasma measurements are less harm to optical components with lower incident flux and reduced stray light that can contaminate optical diagnostics.

active plasma spectroscopy↗
NASA NTRS2004

Recent Progress on the VASIMR Engine

The development of the Variable Specific Impulse Magnetoplasma Rocket (VASIMR) was initiated in the late 1970s to address a critical requirement for fast, high-power interplanetary space transportation. Its high-power and electrodeless design arises from the use of radio frequency (RF) waves to create and accelerate plasma in a magnetic nozzle. While not being a fusion rocket, it borrows heavily from that technology and takes advantage of the natural topology of open-ended magnetic systems. In addition the system lends itself well for Constant Power Throttling (CPT,) an important ability to vary thrust and specific impulse, over a wide operational range, while maintaining maximum power. This allows in-flight mission-optimization of thrust and specific impulse to enhance performance and reduce trip time. A NASA-led, research team, involving industry, academia and government facilities is pursuing the development of this concept in the United States. The technology can be validated, in the near term, in venues such as the International Space Station, where it can also serve as both a drag compensation device and a plasma contactor for the orbital facility. Recent advances in the development of this technology involve the demonstration of efficient propellant utilization in a flowing helicon plasma discharge as well as the experimental verification of single-pass ion acceleration, as predicted by theory I, by coupling RF power to the plasma through ion cyclotron resonance. This paper outlines these and other progress in our understanding of VASIMR physics and presents the concepts for its potential application in NASA's new vision of space exploration.

Chang-Diaz, F. R.↗