Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “HT9”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Investigation of temperature dependence of fracture toughness in high-dose HT9 steel using small-specimen reuse technique

The temperature dependence of fracture toughness in HT9 steel irradiated to 3–145 dpa at 380–503 degrees*C was investigated using miniature three-point bend (TPB) fracture specimens. A miniature-specimen reuse technique has been established: the tested halves of subsize Charpy impact specimens with dimensions of 27 mm *3mm* 4 mm were reused for this fracture test campaign by cutting a notch with a diamond-saw in the middle of each half, and by fatigue-precracking to generate a sharp crack tip. It was confirmed that the fracture toughness of HT9 steel in the dose range depends more strongly on the irradiation temperature than the irradiation dose. At an irradiation temperature <430 *degreesC, the fracture toughness of irradiated HT9 increased with the test temperature, reached an upper shelf of 180—200 MPa*m^.5 at 350–450 degrees*C, and then decreased with the test temperature. At an irradiation temperature >430 degrees*C, the fracture toughness was nearly unchanged up to about 450 *degreesC and decreased slowly with test temperatures in a higher temperature range. Such a rather monotonic test temperature dependence after high-temperature irradiation is similar to that observed for an archive material generally showing a higher degree of toughness. A brittle fracture without stable crack growth occurred in only a few specimens with relatively lower irradiation and test temperatures. In this discussion, these TPB fracture toughness data are compared with previously published data from 12.7 mm diameter disc compact tension (DCT) specimens.

Baek, Jong-Hyuk↗

Radiation-induced swelling and radiation-induced segregation & precipitation in dual beam irradiated Ferritic/Martensitic HT9 steel

Highlights: • The depth-dependence of radiation-induced cavities was characterized in self-ion irradiated HT9 co-implanted with He. • The injected interstitial effect was revealed to suppress cavity swelling in the vicinity of the damage peak. • ChemiSTEM elemental maps revealed the segregation of Ni at cavity surfaces and its possible synergistic influence on swelling was discussed. - Abstract: Ferritic/Martensitic HT9 steel was irradiated at 432 °C to 16.6 displacements per atom (dpa) (at the depth of 600 nm) using a defocused beam of 5 MeV Fe{sup ++} ions, while co-implanted with 3.22 appm He at the same depth. The helium concentration profile was designed so to follow the damage curve with a 0.22 appm He/dpa ratio at the depth from 300 to 1000 nm in the material. The depth-dependence of the cavity size and number density were characterized by both transmission electron microscopy (TEM) and scanning transmission electron microscopy (STEM) imaging methods. A comparison between the two techniques was done showing good agreement. Cavity number density and the resulting swelling were found to be suppressed by the injected interstitial effect in the vicinity of the ion induced damage peak. The region between 300 and 750 nm depth which excludes the injected interstitial effect was thus proposed for improved cavity swelling analysis. The swelling ratio in this region was found to be ~(0.86–1.02) × 10{sup − 2}%/dpa. In addition, ChemiSTEM characterization revealed radiation-induced segregation occurring throughout the irradiated region and precipitation of G-phase particles. Segregation of Ni to cavity surfaces was also observed and its possible synergistic influence on swelling was discussed.

36 MATERIALS SCIENCE↗

Transmission electron microscopy characterization of the fuel-cladding chemical interactions in HT9 cladded U-10Zr fuel

Fuel cladding chemical interaction (FCCI) is a key phenomenon needs to be better understood to establish the design basis for U-10Zr metallic fuel performance. Characterizing the microstructure and chemical composition of FCCI at micron and sub-micron scale is critically important toward a more mechanistic understanding of FCCI phenomenon and its potential effects on cladding integrity and metallic fuel performance. This paper, by using transmission electron microscopy, investigated the FCCI region in HT9 cladded U-10Zr fuel irradiated to 5.7% FIMA burnup at a peak inner cladding temperature of 615 °C in Fast Flux Test Facility (FFTF). Four distinct layers are identified in the FCCI region. The migration of Fe into the fuel side leads to the formation of several U-Zr-Fe ternary phases, including ?-Fe0.5Zr0.32U0.18, e-Fe0.3Zr0.4U0.3, and ?-Fe0.06Zr0.23U0.71, mingled with UFe2, U6Fe, and U phase at various Fe penetration depth up to ~ 150 µm. On the cladding side, grain coarsening and significant lanthanides infiltration along grain boundaries are observed. Laves phase, (Fe,Cr)2(Mo,W), which typically does not exist in fresh HT9, is identified in a wide radial range in the cladding. The typical HT9 martensitic lath structure and pre-existing M23C6 precipitates disappear, partially or completely, depending on the radial distance from the fuel-cladding interface. Those microstructural and compositional changes could cause mechanical degradation in the HT9 cladding. The present characterization results will improve the understanding of FCCI phenomenon and facilitate the development of microstructure-informed FCCI modeling for metallic fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Irradiation dose and temperature dependence of fracture toughness in high dose HT9 steel from the fuel duct of FFTF

To expand the knowledge base for fast reactor core materials, fracture toughness has been evaluated for high dose HT9 steel using miniature disk compact tension (DCT) specimens. The HT9 steel DCT specimens were machined from the ACO-3 fuel duct of the Fast Flux Test Facility (FFTF), which achieved high doses in the range of 3–148 dpa at 378–504 C. The static fracture resistance (J-R) tests have been performed in a servohydraulic testing machine in vacuum at selected temperatures including room temperature, 200 C, and each irradiation temperature. Brittle fracture with a low toughness less than 50 MPa pm occurred in room temperature tests when irradiation temperature was below 400 C, while ductile fracture with stable crack growth was observed when irradiation temperature was higher. No fracture toughness less than 100 MPa pm was measured when the irradiation temperature was above 430 C. It was shown that the influence of irradiation temperature was dominant in fracture toughness while the irradiation dose has only limited influence over the wide dose range 3–148 dpa. A slow decrease of fracture toughness with test temperature above room temperature was observed for the nonirradiated and high temperature (>430 *C) irradiation cases, which indicates that the ductile–brittle transition temperatures (DBTTs) in those conditions are lower than room temperature. A comparison with the collection of existing data confirmed the dominance of irradiation temperature in the fracture toughness of HT9 steels.

Byun, Thak Sang↗

Impact properties of irradiated HT9 from the fuel duct of FFTF

This paper reports Charpy impact test data for the ACO-3 duct material (HT9) from the Fast Flux Test Facility (FFTF) and its archive material. Irradiation doses for the specimens were in the range of 3– 148 dpa and irradiation temperatures in the range of 378–504 *C. The impact tests were performed for the small V-notched Charpy specimens with dimensions of 3 * 4 * 27 mm at an impact speed of 3.2 m/s in a 25 J capacity machine. Irradiation lowered the upper-shelf energy (USE) and increased the transition temperatures significantly. The shift of ductile–brittle transition temperatures (DDBTT) was greater after relatively low temperature irradiation. The USE values were in the range of 5.5–6.7 J before irradiation and decreased to the range of 2–5 J after irradiation. Lower USEs were measured for lower irradiation temperatures and specimens with T-L orientation. The dose dependences of transition temperature and USE were not significant because of the radiation effect on impact behavior nearly saturated at the lowest dose of about 3 dpa. A comparison showed that the lateral expansion of specimens showed a linear correlation with absorbed impact energy, but with large scatter in the results. Size effect was also discussed to clarify the differences in the impact property data from subsize and standard specimens as well as to provide a basis for comparison of data from different specimens. The USE and DDBTT data from different studies were compared.

Byun, Thak Sang↗

Void swelling of conventional and composition engineered HT9 alloys after high-dose self-ion irradiation

Ferritic/martensitic (F/M) steels are being considered as potential structural materials for next generation nuclear reactors, and variants of the alloy HT9 are some of the most promising candidates. In this study, two conventional and two composition engineered HT9 alloys were irradiated using 3.5 MeV Fe 2+ up to 600 peak displacement-per-atom (dpa) at 450 °C. Void swelling and microstructure evolution were characterized for each alloy and compared. The two conventional HT9 alloys (INL and ACO3) showed similar void swelling behavior due to their similar elemental composition and processing conditions. The INL HT9 exhibited a maximum of 2.4% swelling and the ACO3 HT9 showed a maximum of 2.8% swelling at 342 and 393 average local dpa, respectively. On the other hand, the two-composition engineered HT9 alloys with varying N contents (10 ppm for low N and 440 ppm for high N) showed disparate swelling behavior. The low N HT9 exhibited a maximum of 4.6% swelling, while the high N HT9 showed a maximum of 0.7% swelling at 342 average local dpa. Changes in the N content also affected Ni/Si rich G-phase formation. The low N HT9 showed a larger size and lower density of G-phase precipitates compared with the high N HT9 after 600 peak dpa irradiation. This study compares the void swelling behavior of the ion irradiated four current HT9 alloys to extremely high doses, with the void swelling data from neutron irradiated HT9 alloys. Furthermore, the comparison lends critical insights into how well these current alloys can withstand high neutron fluxes in future reactors, especially since the low N and high N HT9 alloys have never been exposed to such high doses before.

36 MATERIALS SCIENCE↗

Comparison of void swelling of ferritic-martensitic and ferritic HT9 alloys after high-dose self-ion irradiation

In this work, ferritic-martensitic (F/M) HT9 along with fully ferritic HT9 specimens were irradiated using self-ions to 600 peak displacement-per-atom (dpa) at 450 °C. To investigate and minimize the carbon contamination effect on void swelling, two identical F/M HT9 specimens were prepared: one without a coating and the other one with a tungsten and silver coating on the surface prior to irradiation. The specimen without a coating showed carbide formation in the matrix, resulting from carbon contamination during irradiation, with no voids observed. The coated sample did not form matrix carbides, and voids were observed within the irradiated region. The same coating was applied to the ferritic HT9, and void swelling results of both the F/M HT9 and the ferritic HT9 alloys were compared after irradiation. The F/M HT9 exhibited a maximum of 2.6% swelling, while the ferritic HT9 showed a maximum of 0.8% swelling at a 400–500 nm depth, equivalent to 334 local dpa. The results were correlated with the instability of carbides in the ferritic HT9 under irradiation. Carbides in the F/M HT9 and the ferritic HT9 are both M23C6, but the matrix carbides in the ferritic HT9 were less stable under the irradiation, compared to the ones on the grain boundaries in the F/M HT9. The study shows the impact of chemistry on the void swelling which overpowers the microstructural factors such as grain size and phase.

36 MATERIALS SCIENCE↗

Small-scale mechanical testing and characterization of fuel cladding chemical interaction between HT9 cladding and advanced U-based metallic fuel alloy

Fuel cladding chemical interactions (FCCI) occurred on the interface between the nuclear metal fuel and cladding is the primary cause of cladding wastage, weakening cladding mechanical integrity, and placing fuel and cladding at risk. Although the microstructural and phase information of FCCI has been fairly understood, mechanical properties remain less studied due to limited reaction volume. Here, through a combining of advanced electron microscopy characterizations and small-scale mechanical testing techniques, including indentation and micro-tensile testing, this study investigated the microscale mechanical properties of FCCI between the ferritic/martensitic (F/M) HT9 cladding and an advanced Uranium (U)-based metallic fuel irradiated at the Advanced Test Reactor to 2.2% FIMA with peak inner cladding temperature reached to 650 °C. Mechanical testing results show significant hardening and embrittlement in the FCCI region. The brittle fracture of FCCI specimen is mainly attributed to the formation of nano-crystallized intermetallic σ-FeCr phase. Whereas mechanical softening was revealed in the unreacted HT9 matrix due to irradiation-induced microstructural and microchemical evolution, specifically, the disappearance of martensitic lath structure and the formation of Fe 2 Mo Laves phase precipitation which consumed the solid solution strengthening Mo from the F/M HT9 matrix. Due to the achieved high cladding temperature, this fuel pin is of particular significance for revealing the high-temperature irradiation effect on the mechanical properties of HT9 cladding. Therefore, the outcomes of this study are expected to contribute to the development of multi-scale mechanical behavior modeling of HT9 cladding for Generation IV reactors which requires cladding to run at higher temperature (above 600 ?).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

HT9 swelling in high burnup fast reactor fuel pin components

The irradiation-induced void swelling of HT9 stainless steel has been observed many times, but there are little data available to quantify the amount of swelling expected as a function of neutron exposure and temperature. This is further complicated by potential heat-to-heat chemical variations or heat treatment conditions during fabrication. Herein, this paper summarizes the results of most of the relevant previously completed studies, then focuses on the swelling behavior of HT9 mixed-oxide fuel cladding and wrapper wire irradiated to high neutron exposures. Note that the hexagonal duct used for the ACO-3 experiment (in the Fast Flux Test Facility, or FFTF) was also made from HT9 and has been studied previously by other researchers. The cladding enables a wider range of operating temperatures. Immersion density and transmission electron microscopy were used to identify a peak in the amount of swelling located axially, just below core centerline, for both the cladding and the wire. The peak roughly coincided with a peak seen in the cladding diameter profile. The wrapper wire showed enhanced swelling compared to the cladding, likely due to over-tempering during wire fabrication heat treatment. The grains showed decreased martensitic structure were larger in size. These data do not provide for the means to fully characterize the swelling of HT9, but do provide further insight into the factors controlling it. The onset of breakaway swelling was not indicated in this data.

36 MATERIALS SCIENCE↗

Nd, SbNd and Sb 3 Nd 4 and their interactions with the cladding alloy HT9

Lanthanide fission products, such as neodymium, formed during the irradiation of metallic fuels are known to cause deleterious effects from chemical interactions occurring at the fuel-cladding interface; a phenomenon known as fuel-cladding chemical interaction (FCCI). The use of fuel-based additives that bind with the lanthanide elements within the fuel meat, alleviating their interactions at the fuel-cladding interface, is one potential method proposed to mitigate the FCCI phenomenon and extend the burnup potential of such metallic fuel systems. In this study, antimony (Sb) is evaluated as one such additive, and neodymium (Nd) is used to represent the lanthanides. A Sb-Nd alloy is fabricated, which consists of two intermetallic phases, SbNd and Sb 3 Nd 4 . Isothermal diffusion couple experiments are carried out at 675 °C for 24 h between Nd and the Fe-12Cr based HT9 cladding alloy. The results are compared against similar diffusion couple experiments carried out between the Sb-Nd alloy and also HT9. Inter-diffusion between Nd/HT9 diffusion couple is characterized and the phases Fe 17 Nd 5 and Fe 17 Nd 2 were found to form whereas no interactions were observed in the Sb-Nd/HT9 diffusion couple. The lack of compound forming tendencies between Fe, the primary alloying constituent of HT9, and SbNd is elucidated through density functional theory (DFT) calculations on enthalpy of mixing, aligning well with the experimental observations. Lastly, the strong binding of Nd with Sb appears to be favorable, alleviating Nd interactions with HT9 constituent elements.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Microchemical evolution of irradiated additive-manufactured HT9

The microstructural responses under 5 MeV Fe2 + single-ion-beam irradiation of three conditions of additive-manufactured (AM) HT9 steel using a powder-based directed energy deposition (DED) technique with and without postbuild heat treatments were investigated. Besides the observed dislocation loop formation and the absence of cavities at the irradiation condition of 50 dpa at 460 °C, Ni/Si/Mn-rich precipitates are found to form in all three conditions of AM-HT9, whereas Cu-rich clusters that arise from Cu uptake from the DED process are only observed in the heat-treated conditions, and not in the as-built (ASB) condition. Coprecipitation of the Cu- and Ni/Si/Mn-rich clusters occur near defect sinks such as line dislocations and grain boundaries in the heat-treated AM-HT9. The variation in microchemical evolution can be directly linked to the starting sink strength of the three AM-HT9 conditions, and the ASB condition with higher sink strength suppressed the responses observed in the postbuild heat-treated specimens.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Evaluation of Sb-Nd and Te-Nd phases within the U-Zr fuel matrix and their interactions with HT9 alloy

Antimony (Sb) and tellurium (Te) were investigated as potential additives for U-10Zr (wt.%) metallic fuel to limit the fuel-cladding chemical interaction (FCCI) with HT-9 alloy. Neodymium (Nd) was utilized to simulate the formation of lanthanide-based solid fission products which are known to play a detrimental role in FCCI. Fuel alloys of U-Zr-Sb-Nd and U-Zr-Te-Nd were evaluated in their annealed condition and compared against their as-cast conditions. Isothermal diffusion couple experiments were performed between U-Zr-Nd, U-Zr-Sb-Nd, and U-Zr-Te-Nd against the cladding alloy HT9 to evaluate the effectiveness of the additives to stabilize Nd within the fuel alloys, as well as investigate the interaction regions that form between the different fuel alloys and HT9. Further, SbNd and Sb 3 Nd 4 , and TeNd are found to be the primary neodymium-based phases formed in the U-Zr-Sb-Nd and U-Zr-Te-Nd alloys, respectively. The zirconium-based phase, Zr 2 Sb, is also found to form within the former alloy. All phases were found to remain stable through the diffusion experiments and exhibited no interaction with HT9 constituent elements. Preferential interaction between Nd with additivities Te and Sb compared to constituting elements in HT9 was further verified based on density functional theory (DFT) calculated enthalpy of mixing.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

FFTF HT9 Cladding Microstructure Characterization

The sodium-cooled fast reactor (SFR) is a promising candidate for next generation nuclear reactors, operating at extreme conditions which include high temperatures (>500?C core outlet temperature) and significant neutron damage. High-Cr martensitic HT9 steel is an excellent candidate for SFR cladding and duct material due to its compatibility with liquid sodium, good thermal conductivity, resistance to void swelling, and strong creep rupture strength [1-4].However, the harsh in-core environment of SFRs can cause complex microstructural changes and mechanical property degradation in HT-9. Ensuring the safe use of HT9 cladding for metallic fuel requires both a thorough understanding of its mechanical response to microstructure evolution as well as reliable microstructure-sensitive modeling predictions. Microstructure-sensitive modeling of high temperature creep behavior in HT9 cladding for SFR applications currently lack experimental data to model the phenomena accurately. To fill this need, methods to perform microstructural characterization have been developed and performed on HT9.

36 MATERIALS SCIENCE↗

Diffusion behavior of lanthanide-additive compounds (Ce 4 Sb 3 , Ce 2 Sb, and CeTe) against HT9 and Fe

Antimony and tellurium have been identified as promising additives in metallic fuel, which can immobilize free-lanthanide fission products into stable intermetallic compounds in order to mitigate the fuel-cladding chemical interaction. Ce 4 Sb 3 , Ce 2 Sb, and CeTe are the primary compounds formed by Sb or Te with the lanthanide Ce present in the fuel. If these compounds are present at the outer periphery of the fuel, they will come in contact with and react with the cladding after the fuel swells. The present study investigates the reactivity of these compounds with two cladding materials, HT9 and Fe. The diffusion couple tests between these compounds and HT9 or Fe were conducted at 853 K. Scanning electron microscopy and transmission electron microscopy were used to analyze the morphology, microstructure, and phase distribution of the diffusion region. It was observed that the diffusion region thickness formed by the three compounds was significantly reduced compared to free Ce. Moreover, there was no observed diffusion or reaction between Ce 4 Sb 3 or Ce 2 Sb with either HT9 or Fe. CeTe was found to diffuse and react with HT9, forming Cr 3 Te 4 and TeFe at the diffusion region, as well as to penetrate into Fe, mainly by intergranular diffusion.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Preliminary Characterization and Mechanical Performance of Additively Manufactured HT9

Laser-blown powder deposition of HT9 was performed to evaluate the feasibility of using advanced manufacturing to fabricate creep strength enhanced ferritic steels. The as-printed materials were tensile tested at room temperature, 330°C, and 550°C to provide a baseline value for the strength levels. The as-fabricated strengths are then compared with wrought materials in the published literature. The strength parameters for the as-fabricated HT9 was found to be significantly higher than that of wrought HT9 without sacrifice in ductility. Two different heat treatment cycles, deemed ACO3 and FCRD, involving two different austentizing temperatures (1065°C and 1040°C) and tempering temperatures (750°C and 760°C) were then evaluated. The heat-treated samples were also tensile tested and were found to show strength and ductility parameters which closely mimicked that of the wrought HT9 literature data. Detailed multi-scale characterization was performed at various length scales. The as-fabricated structure showed a refined martensitic structure with a significant fraction of δ-ferrite present. Closer examination using TEM showed a refined distribution of carbides (predominantly M 23 C 6 and MX or M2X), which would have precipitated during the deposition process. Upon heat treatment, it was seen that the precipitates were more homogenous and refined in the case of the specimens heat treated according to the ACO 3 cycle although there was no significant difference in the strength or the hardness results. However, the specimens heat-treated per the FCRD cycle showed significantly smaller prior austenite grains (measure and give quantitative numbers), which could result in better Charpy toughness. However, the toughness was not evaluated and will be performed in the future. In addition, possible thermos-mechanical treatments (TMT) to refine the grain structure and improve the toughness without compromising the ductility will also be evaluated in the future.

36 MATERIALS SCIENCE↗

Microstructural Characterization of High Dose Irradiated HT9

The present report provides a short summary of the recent efforts to irradiate various HT9 heats and compositions to a high damage level (>500 peak dpa) and characterize the changes to the microstructure. The majority of the data reported here will focus on characterizing the “INL” HT9 heat. This particular heat was chosen due to its high volume fraction of tempered martensite (>90%) in the microstructure. The results show that very little swelling is present in INL HT9 up to doses up to 600 peak dpa. Voids are only observed in the near surface region. Some carbides are also observed to accompany the irradiation. Comparison of void swelling with published neutron irradiation shows good agreement. Additional investigations into the response of delta ferrite grains show a very different distribution of voids and significantly higher void swelling compared to the tempered martensite grains.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Cladding Profilometry Analysis of Experimental Breeder Reactor-II Metallic Fuel Pins with HT9, D9, and SS316 Cladding

BISON finite element method fuel performance simulations were conducted using an existing automated process that couples the Fuels Irradiation & Physics Database (FIPD) and the Integral Fast Reactor Materials Information System database by writing input files and comparing the BISON output to post-irradiation fuel pin profilometry measurements contained within the databases. The importance of this work is to demonstrate the ability to benchmark fuel performance metallic fuel models within BISON using Experimental Breeder Reactor-II fuel pin data for a number of similar pins, while building off previous modeling efforts. Changes to the generic BISON input file include implementing pin specific axial power and flux profiles, pin specific fluences, frictional contact, and irradiation-induced volumetric swelling models for cladding. A statistical analysis of irradiation-induced volumetric swelling models for HT9, D9, and SS316 was performed for experiments X421/X421A, X441/X441A, and X486. Between these three experiments, there were 174 post-irradiation examination (PIE) profilometries used for validating the swelling models presented using a standard error of the estimate (SEE) method. Implementation of the volumetric swelling models for D9 and SS316 claddings was found to have a significant impact on the BISON profilometry simulated, where HT9 clad pins had an insignificant change due to low fluence values. BISON profilometry simulated for HT9, D9, and SS316 fuel pins agreed with PIE profilometry measurements, with assembly SEE values being 4.4 × 10−3 for X421A, 2.0 × 10−3 for X441A, and 2.8 × 10−3 for X486. D9 clad pins in X421/X421A had the highest SEE values, which is due to the BISON simulated profilometry being shifted axially. While this work accomplished its purpose to demonstrate the modeling of multiple fuel pins from the databases to help validate models, the results suggest that the continued development of metallic fuel models is necessary for qualifying new metallic fuel systems to better capture some physical performance phenomena, such as the hot pressing of U-Pu-Zr and the fuel cladding chemical interaction.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗