Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “HIGH LIFT DEVICE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Aeroelastic Trim Drag Optimization of Mach 0.8 Transonic Truss-Braced Wing Aircraft using High-Lift Devices and Control Surfaces

This paper presents an aeroelastic trim drag optimization study of the Mach 0.8 Transonic Truss-Braced Wing (TTBW) aircraft using the High-lift devices and control surfaces. An aero-structural analysis solver VSPAERO with transonic small disturbance, integral boundary-layer, and wing-strut interference corrections coupled to mode shapes computed by NASTRAN using the Galerkin method is developed to provide a rapid aircraft aeroelastic performance evaluation. Three different flight conditions corresponding to Mach 0.8 are selected for the aeroelastic trim drag optimization at the design and off-design cruise lift coefficients. The preliminary optimization results show that the TTBW aircraft with the optimized deflection of the high-lift devices and control surfaces achieves a drag reduction of about 8.2 counts, 6.5 counts, and 9.7 counts corresponding to the lift coefficients 0.661, 0.695, and 0.729, respectively. A high-fidelity CFD solver FUN3D is used to verify the aeroelastic trim drag optimization.

TTBW↗
NASA NTRS1966

A summary of recent large-scale research on high-lift devices

A brief summary of recent 40- by 80-foot wind-tunnel investigations of large-scale models equipped with various high-lift devices is presented. The basic high-lift concepts that were investigated were the externally blown flap, the augmentor wing, and the rotating-cylinder flap. The scope of this paper is limited to a discussion of the wind-tunnel results in terms of maximum lift, descent performance, and pitch trim requirements.

WING FLAP↗
NASA NTRS1949

Summary of section data on trailing-edge high-lift devices

A summary has been made of available data on the characteristics of airfoil sections with trailing-edge high-lift devices. Data for plain, split, and slotted flaps are collected and analyzed. The effects of each of the variables involved in the design of the various types of flap are examined and, in cases where sufficient data are given, optimum configurations are deduced. Wherever possible, the effects of airfoil section, Reynolds number, and leading-edge roughness are shown. For single and double slotted flaps, where a large amount of unrelated data are available, maximum lift coefficients of many configurations are presented in tables.

Cahill, Jones F↗
NASA NTRS1948

Summary of Section Data on Trailing-Edge High-Lift Devices

A summary has been made of available data on the characteristics of airfoil sections with trailing-edge high-lift devices. Data for plain, split, and slotted flaps are collected and analyzed. The effects of each of the variables involved in the design of the various types of flap are examined and, in cases where sufficient data are given, optimum configurations are deduced. Wherever possible, the effects of airfoil section, Reynolds number, and leading-edge roughness are shown. For single and double slotted flaps, where a great mass of unrelated date are available, maximum lift coefficients of a large number of configurations are presented in tables.

Source record↗
NASA NTRS1976

Prediction of longitudinal aerodynamic characteristics of STOL configurations with externally blown high lift devices

A theoretical method has been developed to predict the longitudinal aerodynamic characteristics of engine-wing-flap combinations with externally blown flaps (EBF) and upper surface blowing (USB) high lift devices. Potential flow models of the lifting surfaces and the jet wake are combined to calculate the induced interference of the engine wakes on the lifting surfaces. The engine wakes may be circular, elliptic, or rectangular cross-sectional jets, and the lifting surfaces are comprised of a wing with multiple-slotted trailing-edge flaps or a deflected trailing-edge Coanda surface. Results are presented showing comparisons of measured and predicted forces, pitching moments, span-load distributions, and flow fields.

Mendenhall, M. R.↗
NASA NTRS1952

Effect of High-lift Devices on the Low-speed Static Lateral and Yawing Stability Characteristics of an Untapered 45 Degrees Sweptback Wing

Results of a low-speed wind-tunnel investigation to determine the effect of high-lift devices on the static lateral stability derivatives and the yawing derivatives of an untapered 45 degrees sweptback wing are presented. The tests were made in the curved-flow test section of the Langley stability tunnel at a Reynolds number of 1.1 X 10 to the sixth power.

FLAPS, LEADING EDGE - COMPLETE WINGS↗
NASA NTRS1948

The Effect of Boundary-layer Control by Suction and Several High-lift Devices on the Longitudinal Aerodynamic Characteristics of a 47.5 Degree Sweptback Wing-fuselage Combination

An investigation has been made in the Langley full-scale tunnel of a 47.5 degree sweptback wing-fuselage combination equipped for boundary-layer control by suction. The wing aspect ratio was 3.5, the taper ratio was 0.5, and the airfoil sections normal to the quarter-chord line were NACA 64(sub 1)-A112. The wing configurations tested included the wing with various combinations of extensible leading-edge and split flaps. The effect of Reynolds number, suction-slot location and suction flow coefficient on the aerodynamic characteristics was determined for the model at zero yaw over a range of angle of attack.

WING-FUSELAGE COMBINATIONS - AIRPLANES↗
NASA NTRS1979

A three-dimensional viscous/potential flow interaction analysis method for multi-element wings: Modifications to the potential flow code to allow part-span, high-lift devices and close-interference calculations

The description of the modified code includes details of a doublet subpanel technique in which panels that are close to a velocity calculation point are replaced by a subpanel set. This treatment gives the effect of a higher panel density without increasing the number of unknowns. In particular, the technique removes the close approach problem of the earlier singularity model in which distortions occur in the detailed pressure calculation near panel corners. Removal of this problem allowed a complete wake relaxation and roll-up iterative procedure to be installed in the code. The geometry package developed for the new technique and also for the more general configurations is based on a multiple patch scheme. Each patch has a regular array of panels, but arbitrary relationships are allowed between neighboring panels at the edges of adjacent patches. This provides great versatility for treating general configurations.

Maskew, B.↗
NASA NTRS1948

The Effect of Boundary-layer Control by Suction and of Several High-lift Devices on the Aerodynamic Characteristics in Yaw of a 47.5 Degree Sweptback

An investigation has been made in the Langley full-scale tunnel of a 47.5 degree sweptback wing-fuselage combination equipped for boundary-layer control by suction. The wing aspect ratio was 3.5, the taper ratio was 0.5 and the airfoil sections normal to the quarter-chord line were NACA 61(sub 1)-A112. Tests included the plain wing and the wing with various combinations of extensible leading-edge and split flaps. The investigation was made to determine the effect of boundary-layer control by suction on the aerodynamic characteristics in yaw and on the effectiveness of a split-flap-type aileron for a range of angle of attack and suction-flow coefficient at a Reynolds number of 4.2 x 10 (exp 6) corresponding to a Mach number of approximately 0.07.

BOUNDARY LAYER - COMPLETE WINGS↗