Multi-Variate Optimization of Gen 3 CSP Falling Particle Receivers Using High-Performance Computing
Explore the source record for details and available documents.
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Explore the source record for details and available documents.
To improve the efficiency and lower the cost of Concentrating Solar Power (CSP) plants, new Generation 3 ‘Gen 3’ CSP concepts using novel salts, solids, or gas heattransfer media envisaged to integrated with a supercritical CO 2 (sCO 2 ) power block at temperatures >715ºC are being investigated. Regardless of the specific pathway, critical components including receivers, piping, and heat-exchangers (HXs) will require the use of heat-resistant nickel-based alloys. Furthermore, the use of age-hardenable alloys, such as INCONEL® alloy 740H® (alloy 740H) may be needed to reduce capital cost. The unique challenges presented by CSP plants to material manufacture, such as small diameter thin-walled tubing in receivers, large diameter thin wall piping, and thin sheet and tubes for HXs can add to the cost to produce such alloys when compared to traditional wrought and cast processing. The goal of this project was to facilitate a reduction of plant cost by developing alternate manufacturing routes and quantifying the performance and economic benefits for alloy 740H in comparison to other candidate nickel-based alloys through fabrication trials, high-temperature mechanical property studies, and interactions with technology developers and codes and standards.
Generation 3 Concentrating Solar Power (CSP) Systems require thermal energy storage that can efficiently receive solar heat and deliver it to a working fluid at temperatures greater than 700°C. For liquid systems, the thermal transfer fluid must be phase stable over large temperature ranges. High temperature molten salts meet this criteria, but are difficult liquids to handle. The high heat and salt content can be very corrosive to several different materials that are wetted by the liquid salt. For power tower collectors, the molten salt must be pumped under high pressure to the top of the collector tower. These pumps have impellers and shafts as part of their rotating elements, and under load, require bearings to control shaft movement while rotating. These high temperature pumps require submerged bearings, and thus bearing materials that can withstand the temperature and molten salt contact over long periods of time. This is essential for keeping pump maintenance costs low, and downtime to a minimum. Long running bearing materials is an enabling technology for integrated liquid systems in Generation 3 CSP Systems. Keeping costs low and systems reliable are critical for the broad adoption of Gen 3 CSP Systems. Hayward Tyler, Inc (HTI) proposed development of journal bearing materials for use in vertical pumps designed for pumping high temperature molten salt on both the hot and cold sides of the solar power tower. To complete this objective, HTI utilized the testing capabilities of Oak Ridge National Laboratory (ORNL) and High Temperature System Design (HTSD). Materials would first be selected for static corrosion testing, then downselected for tribological testing. Successful tribologically tested materials would then be downselected for use in additional test regimes. Ten samples were selected for static corrosion testing. Three passed the static testing regime. Two of these materials were downselected for ball material in tribological testing against three metallic alloys: Sintered Y2O3 Partially Stabilized Zirconia YTZP and Silicon Nitride, Grade 147-31N. HTI also proposed collecting data from a thorough bearing test regime using a test rig designed and built as part of this project, and also a conceptual design for a high temperature molten salt vertical pump. HTI withdrew from the project prior to completion of this work and this report reflects only the work completed prior to withdrawal. The completed work produced two papers, one manuscript submitted for publication, and one paper published in the journal Solar Energy Materials and Solar Cells. The papers are: “Tribological behavior of ceramic-alloy bearing contacts in molten salt lubrication for concentrating solar power” and “Material Selection and Corrosion Studies Of Candidate Bearing Materials For Use In Molten Chloride Salt."
To achieve DOE 2030 SunShot targets that reduce the cost of liquid-based solar by an additional 40% to 70% beyond 2018 costs, a more reliable, highly manufacturable flow valve, capable of achieving operational temperatures of >700°C is required [1]. This paper investigates the development of an innovative high-temperature chloride molten salt valve, with operation up to 750°C. This valve is intended to be employed within Gen 3 CSP liquid-based thermal energy storage (TES) systems as well as Gen 4 modular salt reactor (MSR) technologies. This work details the general design and flow testing of a bellows-seal flow control valve (FCV). This design includes an integrated closed-loop thermal control system to ensure robust design for freeze-thaw cycles. The self-contained thermal management STM system, is unique in the salt valve industry since it is an integrated solution to provide a consistent, repeatable alternative to typical heat tracing. Additionally, the design includes the employment of a novel heat pipe valve stem to facilitate enhanced passive thermal management into the valve assembly. This valve stem heat pipe is designed to facilitate natural circulation within the bonnet to ensure robust operation, during both nominal and transient thermal operation. The valve body and trim will be designed using SS316H, consistent with Flowserve Corporation’s existing product base and is code qualified but will utilize clad material for materials corrosion, manufacturing cost reduction and compatibility to ensure design flexibility. A test campaign was performed in this investigation utilizing a novel 750°C ternary chloride (20%NaCl/40%MgCl2/40%KCl by mol. wt. %) molten salt flow loop. A discussion about the design and installation of the valves within this test bed is provided for this investigation. Valve test results from this study assessed Cv curves as well as multiple actuator cycles, under varying thermodynamic and operational mode conditions, which would be characteristic within a commercial molten salt facility. The results indicate nominal operation for the baseline design, though improved performance and reliability is expected with the full designed FCV.
This work investigates the design criteria considering thermal, structural, and material selection of a ternary chloride (MgCl2-NaCl-KCl) molten salt pump that is capable of running at temperatures above 720 °C. In this work, preliminary testing of salt-wetted hydrodynamic bearings was done to investigate different material pairings including Colmonoy grades, Stellite grades, and a novel Nickel Tungsten Carbide alloy (HybrimetTM NiWC3b) used as a High Velocity Oxygen Fuel (HVOF) coating. The coating has shown to withstand the corrosive nature of the molten salt. The pump wetted components are made of Inconel 625 and features a carbon ring seal (CIRPAC Seal) flooded with a N2 gas flow on the overhead to keep salt vapors from interacting with the external ambient air. A comprehensive pump test program has been completed. Over 90 hours run time pumping hot chloride salts at temperatures up to 720 °C in which enough data was captured to produce performance curves at 3 different operating speeds. This research showcases a promising design for use in the Concentrated Solar Power (CSP) Gen 3 liquid-pathway and sets the ground for further development and use of the HybrimetTM NiWC3b as a competitive alternative to available superalloys.
Thermochemical energy storage (TCES) systems offer several advantages over sensible heat storage via molten salts for concentrating solar power (CSP) including: energy density, cost, indefinite storage time, and no risk of freezing. SR’s TCES system utilizes a CaO-based carbonation reaction at high temperature in a fixed bed heat exchanger reactor. The SunShot APOLLO project focuses on the validation of the calcium oxide sorbent for capacity, durability, system economics, and demonstration of the system at a small pilot scale, including system control and operation in simulated on-sun conditions, discharging at 720°C. Under phase I SR completed evaluation of the sorbent loaded in a single-channel heat exchanger reactor. The major accomplishments of phase II are: Design, fabrication and commissioning of a 4 kWhth pilot plant (50x capacity increase from previous bench scale) with a closed-loop CO 2 system, and a commercially relevant heat exchange reactor. The heat exchange reactor has been designed with state-of-the-art modeling tools to ensure 1) sufficient lifetime of the Incoloy body and 2) performance of the packed bed reactor will be adequate to meet the milestones. The rest of the pilot system has been designed with off-the shelf components to maximize reliability and cost effectiveness. The system is highly instrumented and capable of time resolved, independent measurements of the heat and mass balances respectively. Major developments in the technoeconomic analysis (TEA) include 1) reduction of the cost of membrane gas storage for the near-term and future systems and 2) integration with liquid metal receivers and particle receivers for higher decarbonation temperatures and pressures which reduced the cost of gas compression and increased system efficiency. The result are three scenarios with costs bases of 21.9 dollars, 14.3 dollars, and 10.9 dollars/kWhth corresponding to a real LCOE of 59, 57, 56 dollars/MWhe, respectively. The basic operations of the energy storage system were demonstrated for carbonation (discharging) and decarbonation (charging) over short time periods. Excellent control of the CO 2 mass balance across the reactor was achieved with mass flow controllers and the basic operation of the level control of the CO 2 gas bladder was achieved. The system was apparently free from leaks and operated continuously for 18 days with no mechanical failures, thus meeting milestone 2.5.5. The major shortcomings of the system had to do with the controls which prevented us from deep cycling and or reaching high cycles. We were unable to decarbonate (charge) the system for more than a few minutes at a time, which was much shorter than the design target of 10 hrs. This issue could not be resolved due to facility availability and contract closure. One major finding is that CaO-based TCES is most cost efficient when charged with HTF (heat transfer fluid) temperatures >850°C to reach the round-trip exergy efficiency and system cost targets which are higher temperatures than those considered for Gen 3 CSP. Many of the balance of plant components do not exist today, however we are encouraged by our findings that in general with more work we are able to reduce the capital cost, for example with the membrane gas storage, which is an innovative component in itself. The CaO-based TCES system has potential to meet the latest SunShot 2030 goals of LCOE at 50 dollars/MWhe with capital costs of <11/kWhth.
Thermochemical energy storage (TCES) systems offer several advantages over sensible heat storage via molten salts for concentrating solar power (CSP) including: energy density, cost, indefinite storage time, and no risk of freezing. SR’s TCES system utilizes a CaO-based carbonation reaction at high temperature in a fixed bed heat exchanger reactor. The SunShot APOLLO project focuses on the validation of the calcium oxide sorbent for capacity, durability, system economics, and demonstration of the system at a small pilot scale, including system control and operation in simulated on-sun conditions, discharging at 720°C. Under phase I SR completed evaluation of the sorbent loaded in a single-channel heat exchanger reactor. The major accomplishments of phase II are: Design, fabrication and commissioning of a 4 kWhth pilot plant (50x capacity increase from previous bench scale) with a closed-loop CO 2 system, and a commercially relevant heat exchange reactor. The heat exchange reactor has been designed with state-of-the-art modeling tools to ensure 1) sufficient lifetime of the Incoloy body and 2) performance of the packed bed reactor will be adequate to meet the milestones. The rest of the pilot system has been designed with off-the shelf components to maximize reliability and cost effectiveness. The system is highly instrumented and capable of time resolved, independent measurements of the heat and mass balances respectively. Major developments in the technoeconomic analysis (TEA) include 1) reduction of the cost of membrane gas storage for the near-term and future systems and 2) integration with liquid metal receivers and particle receivers for higher decarbonation temperatures and pressures which reduced the cost of gas compression and increased system efficiency. The result are three scenarios with costs bases of 21.9 dollars, 14.3 dollars, and 10.9 dollars/kWh th corresponding to a real LCOE of 59, 57, 56 dollars/MW he , respectively. The basic operations of the energy storage system were demonstrated for carbonation (discharging) and decarbonation (charging) over short time periods. Excellent control of the CO 2 mass balance across the reactor was achieved with mass flow controllers and the basic operation of the level control of the CO 2 gas bladder was achieved. The system was apparently free from leaks and operated continuously for 18 days with no mechanical failures, thus meeting milestone 2.5.5. The major shortcomings of the system had to do with the controls which prevented us from deep cycling and or reaching high cycles. We were unable to decarbonate (charge) the system for more than a few minutes at a time, which was much shorter than the design target of 10 hrs. This issue could not be resolved due to facility availability and contract closure. One major finding is that CaO-based TCES is most cost efficient when charged with HTF (heat transfer fluid) temperatures >850°C to reach the round-trip exergy efficiency and system cost targets which are higher temperatures than those considered for Gen 3 CSP. Many of the balance of plant components do not exist today, however we are encouraged by our findings that in general with more work we are able to reduce the capital cost, for example with the membrane gas storage, which is an innovative component in itself. The CaO-based TCES system has potential to meet the latest SunShot 2030 goals of LCOE at 50 $/MW he with capital costs of <11/kWh th .
Concentrating Solar-Thermal Power (CSP) components such as piping, valves fittings are required for use at temperatures up to 800°C. These are anticipated to be made using Nickel-based alloys such as Haynes ® 230 ® , Haynes ® 282 ® , or IN ® 740H ® and can contribute significantly to the cost of a CSP Gen 3 plant. Thus, there is a significant motivation to lower the cost of materials and components so that the capital costs can be minimized. In all these cases, the cost of the component has two contributions: 1. Materials cost, and 2. Manufacturing cost. Both materials cost and manufacturing costs must be kept low to attain the lowest possible cost. Materials cost can be lowered by using materials that have the ideal combination of properties at the lowest cost. Another avenue to lower cost is chose a manufacturing process that has the potential to lower the cost. Traditionally tubes are made from billets through a wrought process and can be expensive. An alternative process to consider is the centrifugal casting process where the tube is directly fabricated from molten metal. In this case, the molten metal is poured inside a cylindrical metallic mold with an insulating layer and is spun rapidly. A wide range of sizes (diameter, wall thickness, and length) can be cast using this process. The objective of this project was to develop the process for fabricating pipes and related components using a centrifugal casting process and to measure the properties of alloys fabricated using this process.
This work investigates the design criteria considering thermal, structural, and mate-rial selection of a ternary chloride (MgCl2-NaCl-KCl) molten salt pump that is capable of running at temperatures above 720 °C. In this work, preliminary testing of salt-wetted hydrodynamic bearings was done to investigate different material pairings including colmonoy grades, stellite grades, and a novel NiWC-based alloy (i.e. HybrimetTM NiWC3b) used as a High Velocity Ox-ygen Fuel (HVOF) coating. The coating has shown to withstand the corrosive nature of the salt, and is additionally used to protect a 316L stainless steel pump reservoir. The pump wetted components are made of Inconel 625, and it features a carbon ring seal developed by Flows-erve flooded with a N2 gas flow on the overhead to keep salt vapors from interacting with the external ambient air. This research showcases a promising design for use in the CSP Gen 3 liquid-pathway and sets the ground for further development and use of the HybrimetTM NiWC3b as a competitive alternative to available superalloys. Further work will further characterize the pump by performance & cycle testing in molten salt at higher temperatures.
The primary objective of this report is to determine a viable pipe preheating system for a chloride-salt blend that can preheat the pipe to 450°C and withstand a maximum exposure temperature of 750°C. Preheating involves heating the pipe to a specific desired temperature, called preheat temperature, of the pipe. The temperature is maintained by heated molten salt flowing through the piping system. This report reviews 5-types of pipe preheating systems, of which three pipe preheating systems- MI cable, heat tape, and ceramic fiber heaters, were found to be viable for the Gen 3 Liquid Pathway application. The report reviews the pipe preheating efficiency of conduction verses radiant heat transfer. For each of the 5 types of pipe preheating systems, the report describes the system and addresses installation requirements, temperature control, reliability survey, and pre-construction verification testing for the most applicable preheating system. Under Appendix A, images from design drawings demonstrate pipe routing with the preheating system and insulation attached to the pipe along with pipe guides and pipe supports, as designed using Caesar II finite element analysis within the SNL NSTTF Solar Power Tower.
The primary objective of this report is to determine a viable pipe preheating system for a chloridesalt blend (40%MgCl2/20%NaCl/40%KCI) that can preheat the pipe to 450 °C and withstand a maximum exposure temperature of 740 °C. Preheating involves heating the pipe to a specific desired temperature, called preheat temperature, of the pipe. The temperature is maintained by heated molten salt flowing through the piping system. This report reviews 5-types of pipe preheating systems, of which three pipe preheating systems- MI cable, heat tape, and ceramic fiber heaters, were found to be viable for the Gen 3 Liquid Pathway application. The report reviews the pipe preheating efficiency of conduction verses radiant heat transfer. For each of the 5 types of pipe preheating systems, the report describes the system and addresses installation requirements, temperature control, reliability survey, and pre-construction verification testing for the most applicable preheating system. Under Appendix A, images from design drawings demonstrate pipe routing with the preheating system and insulation attached to the pipe along with pipe guides and pipe supports, as designed using Caesar II finite element analysis within the SNL NSTTF Solar Power Tower.
Performance of Silicon Carbide Fiber Composite Receiver Tubes for Concentrating Solar Power
Abstract not provided.
Abstract not provided.
The Facility to Alleviate Salt Technology Risks (FASTR) is a versatile, high-temperature (>600°C) molten chloride salt test facility designed to enable a variety of testing to advance the Generation 3 (Gen 3) Concentrated Solar Power (CSP) molten salt technology. FASTR includes a salt preparation system and a forced flow test loop with a suite of instrumentation. The FASTR loop is capable of 725°C operation, flow rates of 3–7 kg/s, includes heated and cooled sections, and swappable components to enable testing of future vendor-supplied hardware. The salt preparation system supplies large batches (e.g., 200 kg) of clean salt for use in the FASTR forced convection loop. This report summarizes the planned design and capabilities of FASTR. In addition, a failure modes and effects analysis of the system is reported.
Generation 3 (Gen) concentrating solar power (CSP) systems requires a high operation temperature ≥750°C to increase the power-cycle efficiency towards ≥50%. However, such a high operation temperature poses a notable challenge to high temperature materials. On the receiver side, a critical challenge is the lack of solar selective absorbers that demonstrate both high optical-to-thermal energy conversion efficiency η therm approaching 95% and long-term thermal stability at >750°C in air. Existing solar absorbers either have limited η therm ≤89% or deteriorate significantly within 500 h at 750°C; some of these also require costly vacuum deposition for stringent thickness control. Therefore, it is highly desirable to simultaneously achieve η therm ~95% AND high thermal stability at 750°C for future generations of CSP receivers. This project has investigated and developed low-cost, highly scalable spray-coated transition metal oxide nanoparticle (NP) pigmented solar selective coatings on various types of Inconel alloy tube sections that are thermodynamically stable at 750-800°C in air, maintaining η therm >94.3%(93.2%) under a solar concentration ratio of C=1000 after 60 simulated day-night cycles at 750ºC (800ºC) (1 cycle=12 h at 750 or 800°C and 12h ramping down to 25°C). We have also coated up to 48 inches long receiver tubes for preliminary solar testing under Norwich Technology’s parabolic trough systems, demonstrating notably improved performance in solar heating compared to benchmark Pyromark 2500 coatings. Two key innovations have been developed in this project: (1) We achieved an unprecedented high thermal efficiency >94% by optimizing the d-band optical absorption spectra of transition metal ions, engineering their valences and stoichiometry; (2) We were able to maintain or even slightly increase the efficiency when operating at 750°C in air by engineering the interdiffusion of transition metal ions between the coating and the Inconel substrate to our advantage. Featuring high-temperature solar spectral selectivity and thermodynamic stability in air, as well as low-cost, highly scalable solution-chemical synthesis and spray coating techniques, this innovation in solar selective absorber technology alone accounts for nearly 40% of the targeted reduction in the levelized cost of electricity (LCOE) from the receiver, thermal energy storage, and operation & maintenance combined by 2030, as proposed by the U.S. Department of Energy. For a 110 MWe CSP power plant, this LCOE reduction from the solar selective coating alone transfers to ~$\$ $1.9 M increase in annual profit based on a sales price of 10¢/kWh (or an annual sale of $50 M/year). The high solar absorptance (~98%) NP pigment materials developed in this project are equally applicable to volumetric receivers either as a coating or as bigger ceramic microspheres after sintering, potentially benefiting Gen3 falling particle CSP technologies. All these contributions facilitate the larger scale deployment of CSP systems with energy storage capability to address the intermittency issue of solar energy towards dispatchable solar electricity, bridging the temporal gap between peak solar electricity production and peak electricity consumption. The collaboration with Norwich Technologies and Brayton Energy in this project will also facilitate the future commercialization of this new solar selective coating technology developed in this SIPS project.
The Facility to Alleviate Salt Technology Risks (FASTR) is a versatile, high-temperature (>600°C) molten chloride salt test facility designed to enable a variety of testing to advance the Generation 3 (Gen 3) Concentrated Solar Power (CSP) molten salt technology. FASTR includes a salt preparation system and a forced flow test loop with a suite of instrumentation. The FASTR loop is capable of 725°C operation and flow rates of 3–7 kg/s, and it includes heated and cooled sections and swappable components to enable testing of future vendor-supplied hardware. The salt preparation system supplies large batches (e.g., 200 kg) of clean salt for use in the FASTR forced convection loop. This report summarizes the design and capabilities of FASTR in its as-built form as of December 2022.