Markings in radiographs of 2014 aluminum alloy gas tungsten-arc welds.
Radiographic markings in gas tungsten arc welds of aluminum alloys studied for cause of Laue spots
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Radiographic markings in gas tungsten arc welds of aluminum alloys studied for cause of Laue spots
Handbook has been published which integrates results of 19 research programs involving welding of high-strength aluminum alloys. Book introduces metallurgy and properties of aluminum alloys by discussing commercial alloys and heat treatments. Several current welding processes are reviewed such as gas tungsten-arc welding and gas metal-arc welding.
Bend angles for columbium-base alloys, WC3015 and Cb752, at temperatures between -300 F and +500 F are reported. WC3015 exhibited a bend transition temperature well below -100 F, but was severely embrittled by silicide coatings. Cb 752 exhibited a bend transition temperature below -300 F, and the silicide coating application did not influence bend angle of the substrate. However, coating failure on both alloys was observed at less than 60 deg bend, even at 500 F. The effect of electron beam welding and gas tungsten-arc welding on the properties of WC3015 and Cb752 are also reported. Both techniques are shown to produce a marked reduction in the bend angle of WC3015. Unlike WC3015, ductility is restored in Cb752 after a suitable postweld anneal. Microstructural and hardness tests results for both alloys are reported and discussed.
It is pointed out that over 50 different alloys are used in construction of the space shuttle main engines (SSME). Primary construction of the SSME is by welding or brazing of wrought and cast components. Welding processes involve both gas tungsten-arc welds and electron-beam welds. Electroforming has been developed as a process to fabricate and bond structural members for the SSME. Important aspects in the selection of materials and processes are related to weight saving considerations and the high-pressure hydrogen environment. Special problems and their solution in the case of various engine components are discussed, giving attention to the oxidizer preburner, the high pressure oxidizer turbopump, and the heat exchanger.
Commercially pure titanium is used for low-temperature applications due to good toughness attributed to single-phase microstructure (α). Electron beam welding (EBW) and gas tungsten arc welding (GTAW) processes have been used for welding two grades of commercially pure titanium (Grade 2 and Grade 4). Martensitic microstructure is found to be finer in the case of EBW joint as compared to GTAW joint due to faster rate of cooling in the former process. Weldments have been characterized to study the mechanical behavior at ambient (298 K) and cryogenic temperatures (20 and 77 K). Strength of weldments increases with the decrease in temperature, which is found to be more prominent in case of Grade 4 titanium as compared to Grade 2. Weld efficiency of Grade 4 is found to be higher at all the temperatures (ambient, 77 and 20 K). However, ultimate tensile strength/yield strength ratio is higher for Grade 2 as compared to Grade 4. % Elongation is found to increase/retained at cryogenic temperatures for Grade 2, and it is found to decrease for Grade 4. Electron backscattered diffraction analysis and transmission electron microscopy of deformed samples confirmed the presence of extensive twinning in Grade 2 and the presence of finer martensitic structure in Grade 4. Fractography analysis of tested specimens revealed the presence of cleavage facets in Grade 4 and dimples in specimens of Grade 2. Higher strength in Grade 4 is attributed to higher oxygen restricting the twin-assisted slip, which is otherwise prominent in Grade 2 titanium.
Variable-polarity plasma-arc methods produces better welds at lower cost than gas-shielded tungsten-arc welding in assemblies. Weld porosity very low and costs of joint preparation, depeaking, inspection, and weld repair minimized.
The joints of Incoloy 925 obtained from gas tungsten arc welding (GTAW) with pulsating current utilizing ERNiCrMo-3 and ERNiCrMo-10 were investigated under as-welded and direct aged conditions. The microstructure showed the microsegregation of Nb-Mo-, Ti-rich phases in the weld zone of ERNiCrMo-3 in the as-welded condition. Post-weld heat treatment (PWHT) involving direct aging was carried out on the weldments at 732 °C for 4 h followed by air cooling. On direct aging, the tensile strength of the base metal increases by 40% when compared to the as-received ones. The failures were experienced in the parent metal of Incoloy 925 upon tension testing in as-welded conditions. Although the tensile strength was improved considerably, the failures occurred at the fusion zones, for both the fillers in the direct aged conditions. The joint efficiencies of Incoloy 925 welds employing ERNiCrMo-3 and ERNiCrMo-10 were reported as 95 and 86%, respectively. The impact toughness of the weldments in both the as-welded and PWHT conditions was considerably greater compared to that of the candidate metal.
Several engineering components are fabricated by joining similar or dissimilar materials. In the present investigation, welded joints between low alloy steel and austenitic stainless steel were considered. This assembly is one of the critical components in the heat transport system of water-cooled reactors of nuclear power plants. 309L austenitic stainless steel and IN 182 alloys were used for buttering low alloy steel during fabrication of joints. Weld metal was 308L austenitic stainless steel and IN 182, respectively, for the two assemblies. Buttering by 309L SS was performed by gas tungsten arc welding, and the same was done by shield metal arc welding at the time of applying IN 182. Joining of 304L SS and buttered assembly in both the cases was carried out by shield metal arc welding. Evaluation of Vickers micro-hardness was done across the weld centerline for both joints. Microstructure of different regions was examined for the joints. Apart from conventional destructive tests, ultrasonic evaluation of joints was also carried out to ensure weld integrity. In this respect, ultrasonic velocity in longitudinal and shear mode was measured along the transverse direction of the weld. Young’s modulus was determined using ultrasonic tests as well as from the average hardness of different regions. The obtained Young’s modulus by two different techniques revealed satisfactory co-relation. The Young’s modulus obtained from ultrasonic measurements was used to determine the yield strength of different regions across the welds. This technique proved to be useful in identifying the failure prone area across the welded joint.
The current work was carried out to characterize welding of Inconel 600 superalloy and Monel 400. In the present study, gas tungsten arc welding (GTAW) with four types of filler metals (ENiCu, ENiCu-7, ENiCr-3 and ENiCrFe-3) was utilized. The filler metals were categorized into two groups based on the presence of Cr and Nb in their chemical composition. This paper describes the selection and application of welding consumables in manufacturing dissimilar metal combinations. It was found that (Nb/Cr) ratio and Fe content can affect on the size and amount of carbides. During solidification of ENiCr-3 and ENiCrFe-3 filler metals, Nb leaves dendritic cores and is rejected to inter-dendritic regions because of its high tendency for segregation. However, No brittle Laves phase was detected in the welds. The interface between weld metal and base metal and gradual changes in alloying elements were also investigated by scanning electron microscopy. EDX analysis was also applied for different samples. Microhardness measurements and tensile test were performed on the joints. The average hardness value in the weld metal obtained from ENiCrFe-3 is higher than the other welds. ENiCu-7 weld exhibited the highest tensile strength of 540 MPa and percent elongation of 53% in contrast to ENiCrFe-3 weld with the lowest tensile strength (518 MPa) and percent elongation (39%).
The manuscript presents the investigations carried out on the effect of low-temperature sensitization (LTS) of 304L SS weld metal on its corrosion behavior in simulated groundwater, for its application as a canister material for long-term storage of nuclear vitrified high-level waste in geological repositories. AISI type 304L SS weld pad was fabricated by multipass gas tungsten arc welding process using 308L SS filler wire. The as-welded specimens were subsequently subjected to carbide nucleation and further to LTS at 500 °C for 11 days to simulate a temperature of 300 °C for 100-year life of the canister in geological repositories. Delta ferrite (δ-ferrite) content of the 304L SS weld metal substantially decreased on carbide nucleation treatment and further only a marginal decrease occurred on LTS treatment. The microstructure of the as-welded consisted of δ-ferrite as a minor phase distributed in austenite matrix. The δ-ferrite appeared fragmented in the carbide-nucleated and LTS-treated weld metal. The degree of sensitization measured by double-loop electrochemical potentokinetic reactivation method indicated an increase in carbide nucleation treatment when compared to the as-welded specimens, and further increase occurred on LTS treatment. Potentiodynamic anodic polarization investigations in simulated groundwater indicated a substantial decrease in the localized corrosion resistance of the carbide-nucleated and LTS 304L SS weld metals, when compared to the as-welded specimens. Post-experimental micrographs indicated pitting as the primary mode of attack in the as-welded, while pitting and intergranular corrosion (IGC) occurred in the carbide-nucleated weld metal. LTS-treated weld metal predominantly underwent IGC attack. The decrease in the localized corrosion resistance of the weld metal after LTS treatment was found to have a direct correlation with the degree of sensitization and the weld microstructure. The results are detailed in the manuscript.
In the present work, the influence of heat input on phase balance, residual stresses and corrosion resistance of UNS 32101 lean duplex stainless steel welds has been investigated. Three weldment types were obtained with different heat inputs by varying welding current, using gas tungsten arc welding process. The results revealed that increasing heat input caused a significant microstructural evolution with high austenite fraction in weld metals. The residual stresses were measured on the surface and through the sample’s thickness by x-ray diffraction technique based on Sin{sup 2}ψ method. The results showed an inversely proportional relationship between the heat input and the compressive residual stresses on the surface and through the thickness of the weld metal. Potentiodynamic polarization tests of the different welded joints evaluated in 3.5% NaCl solution exhibited high corrosion resistance of the weld metal produced with the low heat input.
This work articulated the multi-pass, gas tungsten arc welding by adopting pulsating current for joining nitrogen-enhanced, low-carbon austenitic stainless steel, AISI 316L(N). An austeno-ferrite stainless steel (ER2594) and an over-alloyed (ERNiCrMo-3) fillers were employed to join 6-mm-thick plates of AISI 316L(N). Acicular and lathy ferrite in the weld zone of ER2594 and the occurrence of secondary phases in the fusion zone of over-alloyed filler were observed. The notch tensile strength data attested that the joint strength was greater for the welds employing an over-alloyed filler. This study also affirms that the welds obtained with ER2594 filler resulted in better impact toughness (144 J) compared with ERNiCrMo-3 filler and base metal. Also the notch impact toughness of ER2594 weldment is increased to 60% in comparison with that of candidate metal. Corrosion studies were also performed by exposing the coupons in a eutectic salt mixture comprising of 40%K{sub 2}SO{sub 4}-60%NaCl for 50 cycles at 650 °C. It is observed that the weld zone employing over-alloyed filler experienced better high-temperature corrosion resistance compared to the base metal. The specific results of this investigation will be of greater demand to the nuclear and marine applications utilizing these joints.
In February 2016 a leak was identified in the 25H evaporator at the Savannah River Site (SRS). The 25H evaporator is used to manage water volume in high level waste (HLW) tanks during solid salt cake and sludge removal. The location and the cause of the leak were unknown. Orano Federal Services (formerly AREVA Federal Services) applied its robotics expertise and commercial nuclear expertise to perform the inspection. Orano and Framatome (formerly AREVA NP INC) combined a BROKK, a commonly used tracked vehicle with remote control, with the KUKA, an automated robotic arm, commonly used in automobile manufacturing, to perform the partial dismantlement and inspection. Once inspection was complete and the leak was identified, Orano conducted a study on two welding processes: Gas Tungsten Arc (GTA-Tig) and Powder Injection Laser Welding. Based on the inspection of the SRS HLW evaporator's material type being Hastelloy{sup R}, along with the remote repair and material thin wall condition, the Powder Injection Laser Welding was chosen for this application. Orano has developed the remote powder injection laser welding and delivery process that will be used to conduct the repair of the SRS HLW evaporator in the fall of 2017. The process includes robotic delivery of components and robotic performance of the weld. Specialized robotic equipment were developed or adapted from other industries to perform the high hazard job of repairing an eroded section of the evaporator pot. The integration of multiple innovative remote techniques provides a unique solution in a highly radioactive environment. These techniques and innovations can be capitalized upon to solve many different remote repairs on equipment resulting in time savings, reduced dose to personnel, and recovery of initial investment in equipment. (authors)
Highlights: • Number of type I and type II boundaries: H-DMWJ > C-DMWJ > W-DMWJ. • Width carbon depleted zones and carbon enriched zones: H-DMWJ > C-DMWJ > W-DMWJ. • Type I and type II boundaries are susceptible to SCC and cracked during mechanical bending. • C-DMWJ has the best performance while H-DMWJ has the worst one. - Abstract: Low-alloy-steel/buttering (or welding) metal interfaces in safe-end dissimilar metal weld joints (DMWJs) at nuclear power plants are weak parts. To optimize the quality of the safe-end DMWJs used for the construction of domestic nuclear power plants and to improve the welding productivity, a series of DMWJs in full-size have been manufactured by using different gas tungsten arc welding (GTAW) methods. The microstructure, chemical composition distribution and local properties across the SA508/52(M) interfaces in these DMWJs are studied. The high heat input and long high temperature duration during hot-wire GTAW process promote the carbon diffusion and grain boundary migration and hence the DMWJ by hot-wire GTAW has the largest amount of type I and type II boundaries and the widest carbon depleted zones and carbon enriched zones, which resulting in the worst performance among the DMWJs in simulated primary water. Type I and type II boundaries are high angle random grain boundaries (RGBs) and Cr-depleted zones are found along type II boundaries resulting in their high susceptibility to SCC. In addition, these boundaries are prone to be cracked during mechanical bending process.
Herein, an FeCrBSi coating was fabricated via plasma spray on AISI1045 steel, and subsequently, a gas tungsten arc welding (GTA) process was employed to remelt the coating. The microstructure, microhardness, fracture toughness and surface roughness of the coating before and after remelting were investigated, as well as the wear resistance was tested by a UMT-3-type sliding wear apparatus. The results showed that, upon remelting, most defects in the as-sprayed coating were effectively eliminated, the surface roughness decreased by 43%, and the coating–substrate interface bonding changed from mechanical to metallurgical. The phase composition of the as-sprayed coating was primarily α-Fe and a small amount of hard Fe{sub 3}B phase, while the remelted coating consisted of α-Fe and (Fe,Cr){sub 23}C{sub 6} and a small quantity of CrB. In addition, remelting the coating was found to induce a 287.6% increase in the fracture toughness, a 33.4% increase in the average microhardness, and a 47.5% decrease in the wear volume, while the failure mechanism changed from abrasive wear to fatigue wear upon remelting. Therefore, GTA remelting of plasma-sprayed coating was found to be a feasible method to obtain a coating with good wear resistance.
The fabrication of prototype titanium alloy primary and secondary mirror support structures for a proposed experimental three-meter space telescope is discussed. The structure was fabricated entirely of Ti-6Al-4V tubing and plate. Fabrication included the development of procedures including welding, forming, and machining. Most of the structures was fabricated by gas-shielding tungsten-arc (GTA) welding with several major components fabricated by high frequency resistance (HFR) welding.
Applicabilities and limitations of three techniques analyzed. NASA technical memorandum discusses physics of electron-beam, gas/ tungsten-arc, and laser-beam welding. From comparison of capabilities and limitations of each technique with regard to various welding conditions and materials, possible to develop criteria for selecting best welding technique in specific application. All three techniques classified as fusion welding; small volume of workpiece melted by intense heat source. Heat source moved along seam, leaving in wake solid metal that joins seam edges together.
Tool that combines clamp with gas nozzle is aid to tungsten/inert-gas (TIG) welding in hard-to-reach spots. Tool holds work to be welded while directing a stream of argon gas at weld joint, providing an oxygen-free environment for tungsten-arc welding.