Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fuel Economy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Model Year 2021 Fuel Economy Guide

The Fuel Economy Guide is published by the U.S. Department of Energy as an aid to consumers considering the purchase of a new vehicle. The Guide lists estimates of miles per gallon (mpg) for each vehicle available for the new model year. These estimates are provided by the U.S. Environmental Protection Agency in compliance with Federal Law. By using this Guide, consumers can estimate the average yearly fuel cost for any vehicle. The Guide is intended to help consumers compare the fuel economy of similarly sized cars, light duty trucks and special purpose vehicles.

2017 EPA fuel economy↗
DOE OSTI2022

Co-optimized Mixed-Mode Engine and Fuel Demonstrator for Improved Fuel Economy while Meeting Emissions Requirements

Progressively increasing regulatory demands on fuel economy and future global emission standards have led to a focus on advanced engine development to improve overall engine efficiency and fulfill emission requirements. Low temperature combustion (LTC) and gasoline compression ignition (GCI) are promising technologies to achieve these goals and have the advantage of using existing refinery infrastructure and subsequent economies of scale for a robust energy supply. By applying spark ignition (SI) for cold start, LTC for low load operations, and GCI for medium to high load operations, a multimode GCI engine concept was proposed and the fuel formation was co-optimized to maximize fuel economy improvement potential while maintaining ULEV 70 emissions standards. HATCI has successfully demonstrated the feasibility of this multimode GCI engine concept, and confirmed the fuel economy improvement over the baseline SI engine by simulating the FTP75 vehicle drive cycle. In this report, the technical approaches, multimode engine control, and engine test results of both steady state and transitions, CFD modeling, fuel testing, and FTP75 drive cycle simulation results are summarized, followed with technical challenges observed, and recommendations for possible follow-up studies.

02 PETROLEUM↗
DOE OSTI2021

Consumer Guide to Fuel Economy

Learn how good driving habits and maintaining your car can improve your fuel economy, as well as other ways to save fuel. This fact sheet from Energy Saver offers tips for how to save fuel and which driving habits and vehicle maintenance practices will have the greatest effect on your fuel economy.

fuel economy, gas mileage, Energy Saver↗
DOE OSTI2022

Improving the effectiveness and equity of fuel economy regulations with sales adjustment factors

Larger vehicles, such as sports utility vehicles, consume more energy than cars. Their increasing popularity runs contrary to the goal of fuel economy regulations to reduce fossil fuel consumption and greenhouse gas emissions and can be explained by consumer preference and lower regulation stringency, which is due to footprint, truck classification, and the omission of heterogenous lifetime vehicle distance traveled among vehicle classes. This study shows that, for both the US and China, large vehicles travel more, last longer, and are owned by higher income consumers. This means large vehicles and their high-income owners use more fuel and emit more pollutants than represented by current policy and thus raises both policy effectiveness and energy equity concerns. We propose and estimate Sales Adjustment Factors that weigh fuel economy standards based on vehicle lifetime usage and demonstrate the resultant significant improvements in the effectiveness and equity of fuel economy regulations.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2021

Assessment of Technologies for Improving Light-Duty Vehicle Fuel Economy—2025-2035

From daily commutes to cross-country road trips, millions of light-duty vehicles are on the road every day. The transportation sector is one of the United States’ largest sources of greenhouse gas emissions, and fuel is an important cost for drivers. The period from 2025-2035 could bring the most fundamental transformation in the 100-plus year history of the automobile. Battery electric vehicle costs are likely to fall and reach parity with internal combustion engine vehicles. New generations of fuel cell vehicles will be produced. Connected and automated vehicle technologies will become more common, including likely deployment of some fully automated vehicles. These new categories of vehicles will for the first time assume a major portion of new vehicle sales, while internal combustion engine vehicles with improved powertrain, design, and aerodynamics will continue to be an important part of new vehicle sales and fuel economy improvement.This study is a technical evaluation of the potential for internal combustion engine, hybrid, battery electric, fuel cell, nonpowertrain, and connected and automated vehicle technologies to contribute to efficiency in 2025-2035. In addition to making findings and recommendations related to technology cost and capabilities, Assessment of Technologies for Improving Light-Duty Vehicle Fuel Economy - 2025-2035 considers the impacts of changes in consumer behavior and regulatory regimes.

MARCHANT, GARY↗
DOE OSTI2022

Evaluating Class 6 Delivery Truck Fuel Economy and Emissions Using Vehicle System Simulations for Conventional and Hybrid Powertrains and Co-Optima Fuel Blends

The US Department of Energy’s Co-Optimization of Engine and Fuels Initiative (Co-Optima) investigated how unique properties of bio-blendstocks considered within Co-Optima help address emissions challenges with mixing controlled compression ignition (i.e., conventional diesel combustion) and enable advanced compression ignition modes suitable for implementation in a diesel engine. Additionally, the potential synergies of these Co-Optima technologies in hybrid vehicle applications in the medium- and heavy-duty sector was also investigated. In this work, vehicles system were simulated using the Autonomie software tool for quantifying the benefits of Co-Optima engine technologies for medium-duty trucks. A Class 6 delivery truck with a 6.7 L diesel engine was used for simulations over representative real-world and certification drive cycles with four different powertrains to investigate fuel economy, criteria emissions, and performance. Comparisons were made between ultralow-sulfur diesel and a blend of 25% hexyl hexanoate with diesel. Model validation data were informed by 2019 model year Cummins ISB 6.7 L diesel engine maps and transient validation data in a pre-production hybrid configuration and a direct dyno coupled configuration with diesel fuel and a blend of 25% hexyl hexanoate with diesel.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

Toward Human-Centric Transportation and Energy Metrics: Influence of Mode, Vehicle Occupancy, Trip Distance, and Fuel Economy

Traditional metrics measuring transportation and energy outcomes can be augmented to better represent impacts on people's lives and systems-level performance. In this context, this study introduces two novel metrics: road capacity (as number of people traveling and accessing services) and energy intensity (as energy use for people traveling and accessing services). Current national-level distributions of available data in the United States for factors contributing to the two new integrated metrics are used as context to evaluate potential outcomes. These factors include vehicle occupancy, mode share, fuel economy, and trip distance. Variations in input values provide insights on how these factors shape efficiencies in road capacity and energy intensity. Parametric sensitivity analysis indicates that the impact of each input depends upon the metric being evaluated. For the human-centered road capacity mobility metric, increasing vehicle occupancy has the largest effect – twice that of increasing mode share for bike, walk, and transit. For the energy intensity mobility metric, the effect of improving fuel economy is the largest. However, when the focus is on accessibility (instead of mobility), for both metrics the effect of lowering average trip distance is the largest. Additionally, a novel interactive tool to visualize the results for various parameter combinations makes the metrics practitioner ready. The findings suggest that the diffusion of new human-centric metrics that benchmark outcomes associated with road capacity and energy may be significant in motivating new sustainable transportation investments and efficient utilization of infrastructure, mobility assets, and services.

ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2023

Analysis of Uncertainty Impacts on Emissions and Fuel Economy Evaluation for Chassis Dynamometer Testing

This study illustrates a methodology for quantifying the uncertainties encountered in the measurement of tailpipe emissions and in the fuel consumption measurements for light-duty conventional vehicles tested on a four-wheel drive chassis dynamometer. The study leverages high-fidelity experimental data collected over three standard drive cycles, UDDS, HWY and US06, intended to simulate a wide range of operating conditions. Here, a method is developed to estimate the measurement uncertainties in fuel consumption for a test cycle, which occur due to the accumulation of measurement uncertainties propagated through the system. The uncertainty determination model uses statistical analysis and standard propagation techniques to evaluate and combine the uncertainties introduced from various sources (including the vehicle, chassis dynamometer, driver, and instrumentation). The analysis also examines three different experimental methods for determining the fuel consumption: 1) carbon mass balance, 2) volumetric fuel scale and 3) gravimetric fuel scale, and takes into consideration the properties of the instrumentation used. The results show that the most significant influence on the determination of the emissions comes from the concentration measurement, and similarly the biggest impact on the total fuel consumption uncertainty comes from the uncertainty in the determination of the carbon dioxide mass, due to the large presence of this pollutant in the overall emissions. It was found that the fuel consumption uncertainties are in the range of ±1-2% for all three methods analyzed, with the lowest values being obtained for measurements performed using the gravimetric method for all three drive cycles considered.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2024

Assessing Total Cost of Driving Competitiveness of Zero-Emission Trucks

This file includes supporting data on modeled medium and heavy-duty vehicle (MHDV) stock, sales, energy consumption, greenhouse gas (GHG) emissions, and total cost of driving (TCD) for the scenarios presented in "Assessing Total Cost of Driving Competitiveness of Zero-Emission Trucks". It also includes input assumptions for vehicle technology attributes (cost and fuel economy), fuel costs, maintenance costs, and the opportunity cost of charging time for the central scenario and relevant sensitivities. Values are reported at the national (United States) level for all vehicle classes and technologies. Tab 'B' inclues definitions, while data is provided in subsequent sheets.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

Correlation between Sensor Performance, Autonomy Performance and Fuel-Efficiency in Semi-Truck Platoons

Semi-trucks, specifically class-8 trucks, have recently become a platform of interest for autonomy systems. Platooning involves multiple trucks following each n close proximity, with only the lead truck being manually driven and the rest being controlled autonomously. This approach to semi-truck autonomy is easily integrated on existing platforms, reduces delivery times, and reduces green- house gas emissions via fuel economy benefits. Level 1 SAE fuel studies were performed on class-8 trucks operating with the Auburn Cooperative Adaptive Cruise Control (CACC) system, and fuel savings up to 10-12% were seen. Enabling platooning autonomy required the use of radar, global positioning systems (GPS), and wireless vehicle-to-vehicle (V2V) communication. Poor measurements and state estimates can lead to incorrect or missing positioning data, which can lead to unnecessary dynamics and finally wasted fuel. This is especially an issue if deceleration is applied in response to a bad measurement. In this study, a faulty radar was shown to cause a greater than 5% increase in fuel consumption. The mechanism of this fuel consumption increase is investigated and applied to other types of sensor failures to indicate their potential effects on fuel economy. This analysis indicates that poor GPS signals over short time can be largely filtered out, with no real gain or loss of fuel economy. V2V communications were intentionally limited by causing interference, which resulted in dropped communication packets over a small physical area, but not an appreciable impact on fuel economy.

vehicle platooning, sensor performance, semi-auton↗
DOE OSTI2023

Auto Stop-Start Fuel Consumption Benefits

With increasingly stringent regulations mandating the improvement of vehicle fuel economy, automotive manufacturers face growing pressure to develop and implement technologies that improve overall system efficiency. One such technology is an automatic (auto) stop-start feature. Auto stop-start reduces idle time and reduces fuel use by temporarily shutting the engine off when the vehicle comes to a stop and automatically re-starting it when the brake is released, or the accelerator is pressed. As mandated by the U.S. Congress, the U.S. Environmental Protection Agency (EPA) is required to keep the public informed about fuel saving practices. This is done, in partnership with the U.S. Department of Energy (DOE), through the fueleconomy.gov website. The “Fuel-Saving Technologies” and “Gas Mileage Tips” sections of the website are focused on helping the public make informed purchasing decisions and encouraging fuel-saving driving habits. Here, in order to provide users with accurate information about the auto stop-start feature, experiments were conducted to determine its fuel economy effect. Four vehicles were tested both with and without the feature enabled under three test cycles: the Federal Test Procedure (FTP) city fuel economy test, the US06 high acceleration aggressive driving schedule that is often identified as the “Supplemental FTP” driving schedule, and the EPA New York City Cycle (NYCC). The results were compared to measure the fuel economy and consumption effects of using the auto stop-start feature. It was found that the fuel economy improvement varied significantly between drive cycles depending on the amount and percentage of idle time during the test. The largest fuel economy improvements were 7.27% and 26.4% for the FTP and NYCC, respectively.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

Experimental Fuel Consumption Results from a Heterogeneous Four-Truck Platoon

Platooning has the potential to reduce greenhouse gas missions of heavy-duty vehicles. Prior platooning studies have chiefly focused on the fuel economy characteristics and three-truck platoons, and most have investigated aerodynamically homogeneous platoons with trucks of the same trim. For real world application and accurate return on investment for potential adopters, non-uniform platoons and the impacts of grade and disturbances on a platoon’s fuel economy must also be characterized. This study investigates the fuel economy of a heterogeneous four-truck platoon on a closed test track. Tests were run for one hour at a speed of 45 mph. The trucks used for this study are two 2015 Peterbilt 579’s with a Cummins ISX15 and a Paccar MX-13, and two 2009 Freightliner M915A5’s, one armored and the other unarmored. Many analysis methodologies were leveraged to describe and compare the fuel data, including lap-wise and track-segment analysis. The methodology for dividing the data into laps is described in detail. The influence of other factors beyond the aerodynamics of platooning is discussed. CAN fuel rate analysis showed excellent agreement with previous experimental trends for two and three-truck platoons. In general, the indicated fuel economy benefits in this study were 5-11% for following vehicles and 0-4% for the lead vehicle in platoon relative to their baseline fuel consumption. On a cumulative basis, all platoons saved fuel, ranging from 6% to 8% versus the sum of the standalone trucks’ fuel consumption. The practical implications of the fuel economy results are discussed, as well as avenues for future research. Introduction and Motivation platooning is controlled coordination of two or more vehicles in a convoy, sometimes called CACC (Coordinated or Cooperative Adaptive Cruise Control). The distance between vehicles in a platoon can be controlled tightly at no additional fatigue to the driver. Platooning vehicles can also respond quickly to braking events of the leader, much more quickly than the typical human driver’s reaction time of 1-1.5 s. Therefore, vehicles in a platoon can follow each other much more closely than would usually be considered a safe following distance under human operation. It is implied that under very close following conditions, platooning technology must be extremely robust before it is safe for wide-scale implementation. Platooning is under investigation as a fuel-saving technology. Close-following significantly reduces aerodynamic drag for both leading and trailing vehicles. According to the NRC in 2010, aerodynamic drag represents roughly half of a Class-8 truck’s on-highway fuel usage, meaning a 20% reduction in drag roughly equals a 10% reduction in fuel usage, if all other sources of energy loss remain equal (i.e. accessory, rolling resistance, drivetrain, braking). It is by aerodynamics that platooning saves fuel. At risk of oversimplifying the aerodynamics, following (or trailing) vehicles experience reduced wind velocity due to shielding, and the leading vehicles experience an increased aft pressure, especially at distances closer than 75’ (23 m).

greenhouse gas emissions, truck platoon, heavy-dut↗
DOE OSTI2021

Household Transportation Energy Affordability by Region and Socioeconomic Factors

Transportation fuel is an important component of household budgets, as 3.3% of total household expenditures are for vehicle fuel nationwide and over 50% of annual household expenditures on energy are for transportation. These average values vary geographically, and higher energy cost burdens are faced by households with lower incomes. Defining transportation energy affordability burden as the percentage of annual household income spent on vehicle fuel, this study aims to quantify affordability as a function of household characteristics and geography. Here, through analysis at the census tract level, this study (i) projects annual household vehicle miles traveled (VMT) based on demographic factors using machine-learning techniques, (ii) estimates local differences in vehicle fuel economy and fuel price, and (iii) quantifies resulting transportation energy affordability by census tract. This study found that the average burden by tract varies from 0.15% to 8%. The variation in affordability can be largely explained by income level and vehicle fuel efficiency. Suburban and rural households spend more on transportation energy compared with urban households because of the usage of less fuel-efficient vehicle technologies and higher annual VMT. Lower-income groups have a wide distribution of the percentage of income spent on transportation energy, 1.2% to 8%, whereas the range for the highest income group ($125,000+) is from 0.15% to 3.9%. This detailed transportation energy affordability analysis provides a better understanding of regional variations in household travel behavior, helps to determine where fuel-efficient vehicle technologies are more likely to be used, and improves estimates of vehicle ownership costs.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2024

Predicting U.S. federal fleet electric vehicle charging patterns using internal combustion engine vehicle fueling transaction statistics

Utilizing fueling transactions from internal combustion engine vehicles (ICEVs), the authors estimated how frequently midday public charging would be required for U.S. federal fleet battery electric vehicles (BEVs). Fueling transaction summary statistics are more widely available than trip-level telematics data, making this methodology more accessible and transferable to other researchers and fleet managers considering BEV replacements. For example, readers can easily apply a linear model using only the count of back-to-back fueling events at gas stations over 57 straight-line miles apart to predict days exceeding range. This linear regression predicted binned days exceeding 250 miles at 80% accuracy on a hold-out test set from the same fleet as the training data and 66 % accuracy on a new fleet displaying different driving behaviors. The authors additionally provide linear equations for days exceeding 200 and 300 miles as alternative range estimates to account for differences in BEV range and temperature impacts. Beyond the single-feature linear models which readers can apply, the authors tuned and trained other machine learning models on a variety of fueling transaction statistics including consecutive transaction distances, transaction distance from garage, estimated miles traveled from fuel economy and fuel quantity, and transaction periodicity. Utilizing a subset of 1678 light-duty federal fleet vehicles which contained daily vehicle miles traveled (VMT) in addition to fueling statistics, the authors determined which fueling transaction statistics were most relevant in predicting driving days exceeding 250 miles (an approximation of BEV rated driving range). In support of the U.S. federal fleet transition to zero-emission vehicles (ZEVs), the authors used these statistics and machine learning models to predict the frequency of BEV midday charging. After training models on the subset with VMT, the authors predicted days exceeding rated range for 112,902 light-duty vehicles operating in similar circumstances in the federal fleet using a Support Vector Regressor (SVR). In conclusion, they then used the projections as part of the ZEV Planning and Charging (ZPAC) tool to identify optimal candidates for BEVs for the federal fleet. An anonymized version of ZPAC is included in the supplementary materials.

25 ENERGY STORAGE↗
DOE OSTI2024

Coupled Neutronics - Thermal-Hydraulics - Thermomechanics modeling of Molten Chloride Reactor

Molten Salt Reactors (MSRs) are innovative Generation-IV nuclear reactors known for their enhanced safety features, fuel economy, and fuel cycle advancements. However, designing and studying these reactors present unique safety and modeling challenges. The Department of Energy (DOE)'s Nuclear Energy Advanced Modeling and Simulation program addresses these challenges through the development of flexible multi-fidelity, multiphysics simulation tools. This study exemplifies NEAMS tools' capabilities by modeling a chloride-based micro-MSR: Griffin for neutronics simulations, Pronghorn for thermal-hydraulics simulations, and BISON for thermomechanics simulations. These tools are integrated into a comprehensive 3D multiphysics model, successfully capturing steady-state and transient reactor operations. A loss of flow accident is examined as an illustrative example of transient behavior. Additionally, this paper contributes to demonstrating the theoretical feasibility of micro-MSR concepts, which have received less attention compared to other designs. The subsequent sections provide a brief description of the MSR concept studied, an overview of the computational tools used, and present results for both steady-state operation and a loss of flow accident.

42 - ENGINEERING↗