Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Failure law”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

The robustness of reliability predictions for series systems of identical components.

The robustness of reliability predictions based on the exponential failure law is investigated under possible deviations within the Weibull family of failure distributions. Regions of robustness are provided for series systems of N identical components, N = 1(1)15; i.e., regions in the space of the Weibull shape parameter, within which one may safely use the exponential prediction procedure and have no more than a prespecified error.

Posten, H. O.↗

Environmental effects and viscoelastic behavior of laminated graphite/epoxy composites

Primarily because of the polymeric matrix, graphite/epoxy composites are viscoelastic materials which exhibit creep and delayed failures. Guided by the time-temperature superposition principle, the authors are developing accelerated characterization techniques to predict the long term compliance behavior and creep rupture strength of composite materials based on short term tests at elevated temperatures. The effect of a post-cure cycle on the compliance and creep rupture strength of composite materials is discussed. The Zhurkov type failure law is applied to experimental creep rupture data of a typical laminate and is shown to correlate the data. A beneficial mechanical strengthening effect is described which significantly affects the failure strengths of specimens which have been under creep loading for a period of time. This aging effect is reversible if the specimen is allowed to recover before being loaded to failure. Other environmental aspects of composite materials are also reviewed.

Dillard, D. A.↗

Analysis of interlaminar fracture in composites under combined loading

Delamination is a predominant failure mode in continuous fiber reinforced laminated composite structures. One type of delamination is the transverse crack tip delamination which originates at the tip of transverse matrix cracks. An analytical model based on the sublaminate approach and fracture mechanics is developed to study the growth of such delaminations. Plane strain conditions are assumed and estimates are provided for the total strain energy release rate as well as the mode 1 and mode 2 contribution. The energy release rate estimates are used in combination with a simple failure law to predict critical delamination growth strains and stresses. These predictions are compared with experimental data on T300/934 Graphite Epoxy (+ or - 25/90 nano seconds) laminates in the range n=.5 to 8. A good agreement is demonstrated for the range of n where the experimental observations indicate transverse crack tip delamination to be the predominant failure mode.

Armanios, Erian A.↗

Earthquake recurrence on the southern San Andreas modulated by fault-normal stress

Earthquake recurrence data from the Pallett Creek and Wrightwood paleoseismic sites on the San Andreas fault appear to show temporal variations in repeat interval. We investigate the interaction between strike-slip faults and auxiliary reverse and normal faults as a physical mechanism capable of producing such variations. Under the assumption that fault strength is a function of fault-normal stress (e.g. Byerlee's Law), failure of an auxiliary fault modifies the strength of the strike-slip fault, thereby modulating the recurrence interval for earthquakes. In our finite element model, auxiliary faults are driven by stress accumulation near restraining and releasing bends of a strike-slip fault. Earthquakes occur when fault strength is exceeded and are incorporated as a stress drop which is dependent on fault-normal stress. The model is driven by a velocity boundary condition over many earthquake cycles. Resulting synthetic strike-slip earthquake recurrence data display temporal variations similar to observed paleoseismic data within time windows surrounding auxiliary fault failures. Our simple model supports the idea that interaction between a strike-slip fault and auxiliary reverse or normal faults can modulate the recurrence interval of events on the strike-slip fault, possibly producing short term variations in earthquake recurrence interval.

Palmer, Randy↗

Techniques for accommodating control effector failures on a mildly statically unstable airplane

Commercial airplanes are becoming increasingly more sophisticated, placing an increasing burden on pilots to detect and resolve the exhaustive set of possible control effector failures. Automatic techniques are needed to either reconfigure an existing control law or restructure a new control law after failure. A discrete control law has been designed for the longitudinal channel of a mildly statically unstable commercial airplane, to track the glideslope during the approach to landing phase of flight. Single effector failures with time delays for failure detection and identification are analyzed for both the reconfigured and restructured control laws, and results are compared with those from previous research using a statically stable airplane. Strategies considered include reconfiguration and restructuring with new flight conditions. Validation of all cases is made using a 6 DOF nonlinear airplane simulation.

Ostroff, A. J.↗

Cumulative creep damage for polycarbonate and polysulfone

The literature for creep to failure cumulative damage laws are reviewed. Creep to failure tests performed on polycarbonate and polysulfone under single and two step loadings are discussed. A cumulative damage law or modified time fraction rule is developed using a power law for transient creep response as the starting point. Experimental results are approximated well by the new rule. Damage and failure mechanisms associated with the two materials are suggested.

Zhang, M.↗

Search for 511 keV electron-positron annihilation radiation from mildly active galaxies using the HEAO 3 gamma-ray spectrometer

The HEAO 3 spacecraft's gamma-ray spectrometer has been used to obtain upper limits to the 511-keV electron-positron annihilation line flux from seven galaxies: M 81/M 82, NGC 4278, M 104, NGC 6500, NGC 2911, and NGC 262. These appear to contain scaled-up versions of the radio source in the galactic center, and their nonthermal activity appears to be confined to the central regions, implying that energetic particles produced in these nuclei do not escape into the low density regions of interstellar or intergalactic space. On the basis of the scaling law adopted, six of these seven galaxies should have been detected above the upper limits obtained for narrow 511 keV emission. Explanations are adduced which account for the scaling law's failure to predict the correct level of radiation annihilation.

Marscher, A. P.↗

Life Limiting Behavior in Interlaminar Shear of Continuous Fiber-Reinforced Ceramic Matrix Composites at Elevated Temperatures

Interlaminar shear strength of four different fiber-reinforced ceramic matrix composites was determined with doublenotch shear test specimens as a function of test rate at elevated temperatures ranging from 1100 to 1316 C in air. Life limiting behavior, represented as interlaminar shear strength degradation with decreasing test rate, was significant for 2-D crossplied SiC/MAS-5 and 2-D plain-woven C/SiC composites, but insignificant for 2-D plain-woven SiC/SiC and 2-D woven Sylramic (Dow Corning, Midland, Michigan) SiC/SiC composites. A phenomenological, power-law delayed failure model was proposed to account for and to quantify the rate dependency of interlaminar shear strength of the composites. Additional stress rupture testing in interlaminar shear was conducted at elevated temperatures to validate the proposed model. The model was in good agreement with SiC/MAS-5 and C/SiC composites, but in poor to reasonable agreement with Sylramic SiC/SiC. Constant shear stress-rate testing was proposed as a possible means of life prediction testing methodology for ceramic matrix composites subjected to interlaminar shear at elevated temperatures when short lifetimes are expected.

Choi, Sung R.↗

Control methods for aiding a pilot during STOL engine failure transients

Candidate autopilot control laws that control the engine failure transient sink rates by demonstrating the engineering application of modern state variable control theory were defined. The results of approximate modal analysis were compared to those derived from full state analyses provided from computer design solutions. The aircraft was described, and a state variable model of its longitudinal dynamic motion due to engine and control variations was defined. The classical fast and slow modes were assumed to be sufficiently different to define reduced order approximations of the aircraft motion amendable to hand analysis control definition methods. The original state equations of motion were also applied to a large scale state variable control design program, in particular OPTSYS. The resulting control laws were compared with respect to their relative responses, ease of application, and meeting the desired performance objectives.

Nelson, E. R.↗

Investigation of control law reconfigurations to accommodate a control element failure on a commercial airplane

The ability of a pilot to reconfigure the control surfaces on an airplane after a failure, allowing the airplane to recover to a safe condition, becomes more difficult with increasing airplane complexity. Techniques are needed to stabilize and control the airplane immediately after a failure, allowing the pilot more time to make longer range decisions. This paper presents a baseline design of a discrete multivariable control law using four controls for the longitudinal channel of a B-737. Non-reconfigured and reconfigured control laws are then evaluated, both analytically and by means of a digital airplane simulation, for three individual control element failures (stabilizer, elevator, spoilers). The simulation results are used to evaluate the effectiveness of the control reconfiguration on tracking ability during the approach and landing phase of flight with severe windshear and turbulence disturbing the airplane dynamics.

Ostroff, A. J.↗

Fault tolerant control laws

A systematic procedure for the synthesis of fault tolerant control laws to actuator failure has been presented. Two design methods were used to synthesize fault tolerant controllers: the conventional LQ design method and a direct feedback controller design method SANDY. The latter method is used primarily to streamline the full-state Q feedback design into a practical implementable output feedback controller structure. To achieve robustness to control actuator failure, the redundant surfaces are properly balanced according to their control effectiveness. A simple gain schedule based on the landing gear up/down logic involving only three gains was developed to handle three design flight conditions: Mach .25 and Mach .60 at 5000 ft and Mach .90 at 20,000 ft. The fault tolerant control law developed in this study provides good stability augmentation and performance for the relaxed static stability aircraft. The augmented aircraft responses are found to be invariant to the presence of a failure. Furthermore, single-loop stability margins of +6 dB in gain and +30 deg in phase were achieved along with -40 dB/decade rolloff at high frequency.

Ly, U. L.↗

Addressing Control Research Issues Leading to Piloted Simulations in Support of the IFCS F-15

This report summarizes the research effort by a team of researchers at West Virginia University in support of the NASA Intelligent Flight Control System (IFCS) F-15 program. In particular, WVU researchers assisted NASA Dryden researchers in the following technical tasks leading to piloted simulation of the 'Gen_2' IFCS control laws. Task #1- Performance comparison of different neural network (NN) augmentation for the Dynamic Inversion (DI) -based VCAS 'Gen_2' control laws. Task #2- Development of safety monitor criteria for transition to research control laws with and without failure during flight test. Task #3- Fine-tuning of the 'Gen_2' control laws for cross-coupling reduction at post-failure conditions. Matlab/Simulink-based simulation codes were provided to the technical monitor on a regular basis throughout the duration of the project. Additional deliverables for the project were Power Point-based slides prepared for different project meetings. This document provides a description of the methodology and discusses the general conclusions from the simulation results.

Napolitano, Marcello↗

Robust Gain-Scheduled Fault Tolerant Control for a Transport Aircraft

This paper presents an application of robust gain-scheduled control concepts using a linear parameter-varying (LPV) control synthesis method to design fault tolerant controllers for a civil transport aircraft. To apply the robust LPV control synthesis method, the nonlinear dynamics must be represented by an LPV model, which is developed using the function substitution method over the entire flight envelope. The developed LPV model associated with the aerodynamic coefficient uncertainties represents nonlinear dynamics including those outside the equilibrium manifold. Passive and active fault tolerant controllers (FTC) are designed for the longitudinal dynamics of the Boeing 747-100/200 aircraft in the presence of elevator failure. Both FTC laws are evaluated in the full nonlinear aircraft simulation in the presence of the elevator fault and the results are compared to show pros and cons of each control law.

Shin, Jong-Yeob↗

A Reliability Model for Ni-BaTiO3-Based (BME) Ceramic Capacitors

The evaluation of multilayer ceramic capacitors (MLCCs) with base-metal electrodes (BMEs) for potential NASA space project applications requires an in-depth understanding of their reliability. The reliability of an MLCC is defined as the ability of the dielectric material to retain its insulating properties under stated environmental and operational conditions for a specified period of time t. In this presentation, a general mathematic expression of a reliability model for a BME MLCC is developed and discussed. The reliability model consists of three parts: (1) a statistical distribution that describes the individual variation of properties in a test group of samples (Weibull, log normal, normal, etc.), (2) an acceleration function that describes how a capacitors reliability responds to external stresses such as applied voltage and temperature (All units in the test group should follow the same acceleration function if they share the same failure mode, independent of individual units), and (3) the effect and contribution of the structural and constructional characteristics of a multilayer capacitor device, such as the number of dielectric layers N, dielectric thickness d, average grain size r, and capacitor chip size S. In general, a two-parameter Weibull statistical distribution model is used in the description of a BME capacitors reliability as a function of time. The acceleration function that relates a capacitors reliability to external stresses is dependent on the failure mode. Two failure modes have been identified in BME MLCCs: catastrophic and slow degradation. A catastrophic failure is characterized by a time-accelerating increase in leakage current that is mainly due to existing processing defects (voids, cracks, delamination, etc.), or the extrinsic defects. A slow degradation failure is characterized by a near-linear increase in leakage current against the stress time; this is caused by the electromigration of oxygen vacancies (intrinsic defects). The two identified failure modes follow different acceleration functions. Catastrophic failures follow the traditional power-law relationship to the applied voltage. Slow degradation failures fit well to an exponential law relationship to the applied electrical field. Finally, the impact of capacitor structure on the reliability of BME capacitors is discussed with respect to the number of dielectric layers in an MLCC unit, the number of BaTiO3 grains per dielectric layer, and the chip size of the capacitor device.

reliability↗

A dynamical model of lithosphere extension and sedimentary basin formation

The effect of convection-induced stresses at the base of the continental lithosphere on surface and extensional deviatoric stresses is investigated. The biaxial strain in the continental lithosphere is controlled by power law creep in the upper and lower crust, brittle failure, and the Dorn plasticity law. The relationship between the lithosphere stress distribution and Moho temperatures is examined. The extension factors, basin subsidence, heat flow, and sediment loading of the lithosphere are studied.

Houseman, G.↗

A comparison of CMG steering laws for High Energy Astronomy Observatories (HEAOs)

A comparison of six selected control moment gyro steering laws for use on the HEAO spacecraft is reported. Basic equations are developed to project the momentum and torque of four skewed, single gimbal CMGs into vehicle coordinates. In response to the spacecraft attitude error signal, six algorithms are derived for controlling the CMG gimbal movements. HEAO performance data are obtained using each steering law and compared on the basis of such factors as accuracy, complexity, singularities, gyro hang-up and failure adaption. Moreover, each law is simulated with and without a magnetic momentum management system. The performance of any steering law is enhanced by the magnetic system. Without magnetics, the gimbal angles get large and there are significant differences in steering law performances due to cross coupling and nonlinearities. The performance of the pseudo inverse law is recommended for HEAO.

Davis, B. G.↗

A Flight Control System Architecture for the NASA AirSTAR Flight Test Infrastructure

A flight control system architecture for the NASA AirSTAR infrastructure has been designed to address the challenges associated with safe and efficient flight testing of research control laws in adverse flight conditions. The AirSTAR flight control system provides a flexible framework that enables NASA Aviation Safety Program research objectives, and includes the ability to rapidly integrate and test research control laws, emulate component or sensor failures, inject automated control surface perturbations, and provide a baseline control law for comparison to research control laws and to increase operational efficiency. The current baseline control law uses an angle of attack command augmentation system for the pitch axis and simple stability augmentation for the roll and yaw axes.

Murch, Austin M.↗