Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FLAME”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Direct numerical simulations of turbulent premixed cool flames: Global and local flame dynamics analysis

The cool flame dynamics, especially in turbulent flows, is of great interest for both practical application and fundamental research. Here, in this study, a series of direct numerical simulations of turbulent premixed n-C 7 H 16 /O 2 /O 3 /N 2 cool flames are performed, with the focus on the influence of turbulence intensity (u'/S L , where S L is the laminar flame speed) on the flame structure as well as the global and local cool flame dynamics. It is found that the cool flame front is considerably wrinkled by turbulence at high u'/S L , leading to significantly thickened turbulent cool flame brush and largely altered local reactivity compared with the reference laminar flame. However, the turbulent flame structure in the temperature space is found to be insensitive to u'/S L . Besides, with increasing u'/S L , the normalized turbulent cool flame speed (S L /S L ) is monotonically increased, attributed to substantial augmentation on the flame surface area (A T /A L ), while the stretching factor (I 0 ) remains almost constant and is smaller than 1. The underlying mechanisms for such variations are revealed through local flame dynamics analysis. Specifically, the local flame displacement speed S d is found to be strongly negatively correlated with flame curvature; meanwhile, such negative correlation and the probability distribution function (PDF) of flame curvature are barely influenced by u'/S L , leading to a weak dependence of I 0 on u'/S L . In contrast, the PDF of the tangential strain rate is found to span a much wider range and shift to the positive side as u'/S L increases, suggesting that the enhanced tangential strain rate is the main cause for the increase in surface area of the turbulent premixed cool flame. Finally, the influence of equivalence ratio on above findings is found to be insignificant, indicating that although the local reactivity of turbulent premixed cool flames is altered due to the differential diffusion, the resultant flame- stretch interaction is insensitive to the equivalence ratio. This study presents some unique cool flame dynamics that are distinct from hot flames, which can help improve the understanding and modeling of turbulent cool flames.

Cool flames↗
DOE OSTI2026

Flame dynamics and kinetic coupling of ammonia and dimethyl-ether in non-premixed cool and warm flames at elevated pressure

Developing advanced low-temperature combustion engines with ammonia-biofuel blends requires a comprehensive understanding of low-temperature flame dynamics and kinetic interactions between ammonia and oxygenated fuels at elevated pressures. This work aims to study the dynamics and kinetics of non-premixed Dimethyl Ether (DME)/Ammonia (NH 3 ) cool and warm flames, and their reignition to hot flames. A counterflow burner is employed to establish DME/NH 3 cool/warm flames at pressures up to 5 atm. The extinction limits of cool flame and the reignition limits of warm flame to hot flame are measured by varying NH 3 concentrations and compared to simulations to quantitatively examine the effects on DME/NH 3 flames. It is found that NH 3 inhibits low-temperature DME oxidation and results in lower cool flame extinction limits. Warm flames in the presence of NH 3 are observed for the first time, revealing a non-monotonic effect of NH 3 addition: a small amount of NH 3 presence enhances warm flame chemistry and promotes reignition to hot flames, while a high NH 3 concentration weakens the warm flame. This trend is further explained by 0-D PSR kinetic simulations and 1-D S-curve flame dynamic calculations. Three flame transition regimes between cool flames (CF), warm flames (WF), and hot flames (HF) by different levels of NH 3 additions at a specific strain rate are identified, namely WFHF reignition, WF-CF transition, and WF extinction. Reaction sensitivity analyses of OH at low temperatures show that NH3 inhibits DME oxidation through OH consumption via H-abstraction and the kinetic couplings of RO 2 /NH 2 , RO 2 /NO x , R/NO x , and O 2 QOOH/NO x further suppress the low-temperature branching. At intermediate-temperatures, NH 2 /NO x /HO 2 coupling promotes warm flames via the pathway NH 2 → H 2 NO → HNO → NO by converting O 2 → HO 2 → OH. At even higher NH₃ concentrations, radical termination reactions of NH 2 + NO/NO 2 and excessive OH consumption via H-abstraction inhibit the flame. The insights into the kinetic coupling between NH 3 and low-temperature chemistry at elevated pressure and its impact on the dynamics of cool-warm-hot flame transitions will contribute to advancing combustion technologies with reduced emissions and improved energy-efficiency.

42 ENGINEERING↗
DOE OSTI2024

High-Speed OH-PLIF Diagnostics of Flame Flashback in Low Swirl Hydrogen-Enriched Flames

This paper reports flashback events observed in hydrogen-enriched flames stabilized in a low swirl burner (LSB) at atmospheric pressure and temperature conditions. The fundamentals of hydrogen-rich stable flames and spatiotemporal investigation of flashback phenomena were observed experimentally using a high-repetition-rate nanosecond (ns)-duration hydroxyl radical planar laser-induced fluorescence (OH-PLIF) diagnostic. Testing was conducted in an optically accessible pre-mixing section of a LSB with inlet pre-mixing velocities ranging from 5 to 10 m/s for methane and hydrogen (50 – 90% by mole) blends. Swirlers with two different turning angles, 26o and 33o, and three different perforated plate hole diameters, 1.08, 1.12 and 1.16 mm, with measured swirl numbers varying from 0.43 to 0.49 were used in this study at atmospheric temperature and pressure inlet conditions. The flashback propensity showed a dependence on the proximity of the lifted flame to the burner exit (termed as lift-off length, L) which was dependent on the pre-mixer velocity (V), hydrogen content (XH2) and equivalence ratio (ϕ) at constant temperature and pressure conditions. High-speed OH-PLIF images revealed lifted flames were first observed at low ϕ/ XH2 condition which then changed to a M-shaped flame attached to burner rim with the increase in ϕ/ XH2. Further increases in ϕ/XH2, depending upon other inlet parameters, triggered flame flashback into the pre-mixing section. Flashback occurred when burning began in the outer shear layer and the leading flame brush propagated into the nozzle. Such spatiotemporally resolved high-speed OH-PLIF imaging provides insights on different stages of flashback in a LSB – flashback initiation, transition of flame propagation from burner exit to the swirler and flashback to flame holding transition. Flame ϕ at flashback showed an expected linearly increasing trend with increasing V and decreasing XH2 and the conclusions drawn aligned well with detailed investigations. For identical inlet conditions, flashback propensity decreased with increasing perforated-plate hole diameter and increasing swirler vane angle.

Parajuli, Pradeep↗
DOE OSTI2026

Flame stabilization in DME spray flames under engine-relevant conditions characterized by OH* chemiluminescence and formaldehyde laser-induced fluorescence

The transient and quasi-steady flame structures of Dimethyl Ether (DME) fuel sprays, produced by a single-hole injector (Spray D), were investigated using Planar Laser-Induced Fluorescence (PLIF) and chemiluminescence imaging in a constant-volume chamber under Engine Combustion Network (ECN) Spray A conditions (900 K ambient temperature, 60 bar ambient pressure, 1500 bar injection pressure, and 22.8 kg/m 3 ambient density). Low-temperature chemical reaction zones were visualized using formaldehyde (CH 2 O) PLIF with 355 nm excitation, while high-temperature flame regions were captured via chemiluminescence imaging of excited-state hydroxyl radicals (OH*). Both transient and quasi-steady flame structures clearly show the transition from CH 2 O to OH*, highlighting the progression from low- to high-temperature combustion, while the position of the flame is displaced for DME compared to reference hydrocarbon n-dodecane. Homogeneous reactor calculations with detailed chemistry and using adiabatic mixing for initial temperature show that CH 2 O peaks are significantly higher for DME at the same equivalence ratio, with a higher heat-release during the cool-flame regime with respect to the fuel heating value. Thus, the cool-flame dynamic as a precursor to high-temperature combustion and flame stabilization exhibit distinct behavior for DME relative to conventional hydrocarbons, and these phenomena are effectively resolved through the soot-free nature of DME and the high-speed, time-resolved diagnostics.

CH2O laser-induced fluorescence↗
DOE OSTI2026

Flame Characterization and Flashback Studies of Hydrogen-Enriched Low-Swirl Flames Using High-Speed OH-PLIF

Here, this paper reports the flashback mechanism observed in hydrogen-enriched flames stabilized in a low-swirl burner (LSB) at atmospheric temperature and pressure. The fundamentals of hydrogen-rich stable flames and spatiotemporal information of flashback phenomena were observed experimentally using a high-repetition-rate nanosecond (ns)-duration hydroxyl planar laser-induced fluorescence (OH-PLIF) diagnostic. Testing was conducted for methane and hydrogen (50–90%H 2 , by mole) blends in an optically accessible LSB premixer with measured swirl numbers varying from 0.43 to 0.49. The flashback propensity showed dependence on liftoff length, which was dependent on premixer velocity (𝑉), hydrogen content (𝑋 H 2 ), and equivalence ratio (𝜙) at constant temperature and pressure. High-speed OH-PLIF images revealed that lifted flames were first observed at low 𝜙/𝑋 H 2 conditions, which were changed to an M-shaped flame attached to the burner rim with an increase in 𝜙/𝑋 H 2 . A further increase in 𝜙/𝑋 H 2 triggered the flame flashback into the premixer. Flame 𝜙 at flashback (𝜙 FB ) showed an expected linearly increasing trend with increasing 𝑉 and decreasing 𝑋 H 2 , and the conclusions drawn aligned well with detailed liftoff length investigations. The 𝜙 FB increased with increasing perforated plate hole diameter and increasing swirler vane angle. The vane angle had little effect on flashback tendency at high premixer velocity.

combustion↗
DOE OSTI2024

High-Speed OH-PLIF Diagnostics of Flame Flashback in Low Swirl Hydrogen-Enriched Flames

Hydrogen-enrichment is a potential strategy to reduce carbon emissions for the development of next-generation lean premixed combustors. However, the higher flashback propensity with hydrogen enrichment owing to the faster chemical kinetics is one of the key challenges in existing natural gas turbine combustors. The fundamentals of stabilized flame dynamics and flashback events in a premixed low swirl burner (LSB) configuration are visualized experimentally using nanosecond (ns)-based high-speed hydroxyl radical planar laser-induced fluorescence (OH-PLIF). Swirlers with two different turning angles, 26 and 33 and three different center-body hole diameters, 1.08, 1.12 and 1.16 mm with measured swirl numbers varying from 0.43 to 0.49 are tested in this study at atmospheric temperature and pressure inlet conditions. The inlet conditions are varied systematically with respect to pre-mixer velocities (V), flame equivalence ratio (ϕ) and hydrogen content (X_(H_2 )) for 50%-90% (H2, by mole) H2/ CH4 reactant mixtures and OH-PLIF characterization is performed in a stable flame at 20 kHz repetition rate. An increase in flashback propensity is observed with increasing ϕ, X_(H_2 ) and decreasing V via detailed investigation of flame lift-off length (L) above the burner rim.

Parajuli, Pradeep↗
DOE OSTI2024

Heat release surrogates for NH 3 /H 2 /N 2 –air premixed flames

The present study investigates the performance of NH, NH 2 , O-atom, and H-atom as heat release rate (HRR) surrogates for NH 3 /H 2 /N 2 –air premixed flame through simulations. The simulations are conducted across different pressures, reactant inlet temperatures, fuel blend compositions, and equivalence ratios. Cantera is used to simulate one-dimensional (1D) freely propagating flames to investigate the spatial correlations of the species with the HRR. PeleLMeX, a low-Mach direct numerical simulation (DNS) code with Adaptive Mesh Refinement (AMR), is used to simulate two-dimensional (2D) flame-vortex interactions to investigate the temporal correlations including stretch effects. Three different mechanisms (Jiang et al. 2020; Glarborg et al. 2018; Okafor et al. 2018) were considered in the 1D flame simulations, whereas only the Jiang mechanism was considered in the flame-vortex simulations. The HRR surrogate performance for the 2D flames is evaluated at two different locations: (1) the centerline and (2) the flame cusp. The cusp is defined as the region in the flame front with the greatest curvature and the centerline encounters the highest tangential strain rate. The 1D flame results suggest that, although there is not uniformly good spatial correlation for HRR across all flame conditions, NH is the best overall as a HRR surrogate for laminar flames. The 2D flame results, however, suggest that O-atom and H-atom have satisfactory temporal correlations at different conditions—the former for rich flames, the latter for high-pressure flames. Furthermore, these simulations provide guidance to experimental measurements of surrogate HRR markers in unsteady multi-dimensional flames using laser diagnostics to detect species such as NH, O-atom, and H-atom.

Ammonia↗
DOE OSTI2026

Biobased Flame Retardants Towards Sustainable Building Materials with Low Embodied Carbon

Incorporation of fire retardants in different types of products is one of the essential steps in the material production process to minimize fire risk and meet fire safety requirements. A variety of commonly used flame retardants based on halogen, mineral, and other compounds has gained popularity due to their efficient flame-retardant behaviors. However, especially in the case of halides, there are numerous toxicity related issues and environmental pollution effects that have urged the building sector to deviate from their use and focus on the development of non-toxic alternatives. Therefore, to enhance the safety of flame retardants, the synthesis of flame retardants from waste feedstocks using phosphorous chemistry with a dual flame-retardant mechanism has been established. A range of waste feedstocks that include cardanol, vanillin, and gallic acids has been converted into a series of flame retardants using a one-step approach by incorporating phosphorous moieties into their structures. The established pathways allow to develop a range of flame-retardant materials by converting waste feedstocks into phosphorous-based materials with inherent flame retardancy. The introduction of abundant aromatic structures from biobased feedstocks enables high charring capabilities in materials in which these biobased flame retardants have been incorporated, increasing their char yields which significantly enhances the flame suppressing properties of the designed materials. Studies show that inclusion of phosphoric moieties into structures allows the displacement of flame enhancing radicals, by releasing non-flammable and non-toxic gases, therefore inhibiting the spread of fire in the gas phase. The resulting biobased flame retardants have been incorporated in wood substrates, foam insulation, and hemp fibers where the results show that only 1-5% of loading of biobased flame retardant suppressed the flame completely. This study represents a novel approach for the development of flame retardants with high performance while utilizing waste feedstocks as a source for their design.

Demchuk, Zoriana [ORNL] (ORCID:0000000326292235)↗
DOE OSTI2025

The composition of gases from a diffusion flame above longleaf pine needle fuel beds

The gas and tar composition of a diffusion flame from longleaf pine needles is currently poorly understood and more data are needed to fill in the gap between pyrolysis data and smoke plume data, thus improving physical and chemical modeling of wildland smoke formation. A pilot experiment to measure light gas and tar composition of such a flame is described for three flame regions: persistent flame (flame base), intermittent flame, and smoke plume. Flame gases from 24 experimental fires were collected in canisters and analyzed using EPA method TO-14A for CO 2 , CO, H 2 , CH 4 , and C 2 to C 7 hydrocarbon gases. Condensed gas (tar) samples were collected and analyzed using GC/MS. Other light gases were measured using FTIR spectroscopy. Results from compositional data analysis suggest significant differences in (relative) concentration of compounds detected in the three regions of the flame. Statistical tests for differences in flame zones were performed using the canister data: Concentration of hydrocarbons relative to CO and CO 2 decreased from the persistent flame zone above the pyrolyzing needles through the intermittent flame region into the flame-free plume. This was likely due to both chemical reactions (oxidation) occurring in the flame as well as the introduction of air into the flame/plume by entrainment.

Biomass↗
DOE OSTI2024

Direct numerical simulation of a high-pressure hydrogen micromix combustor: Flame structure and stabilisation mechanism

A high-pressure hydrogen micromix combustor has been investigated using direct numerical simulation with detailed chemistry to examine the flame structure and stabilisation mechanism. The configuration of the combustor was based on the design by Schefer et al., using numerical periodicity to mimic a large square array. A precursor simulation of an opposed jet-in-crossflow was first conducted to generate appropriate partially-premixed inflow boundary conditions for the subsequent reacting simulation. The resulting flame can be described as an predominantly-lean inhomogeneously-premixed lifted jet flame. Five main zones were identified: a jet mixing region, a core flame, a peripheral flame, a recirculation zone, and combustion products. The core flame, situated over the jet mixing region, was found to burn as a thin reaction front, responsible for over 85% of the total fuel consumption. The peripheral flame shrouded the core flame, had low mean flow with high turbulence, and burned at very lean conditions (in the distributed burning regime). It was shown that turbulent premixed flame propagation was an order-of-magnitude too slow to stabilise the flame at these conditions. Stabilisation was identified to be due to ignition events resulting from turbulent mixing of fuel from the jet into mean recirculation of very lean hot products. Ignition events were found to correlate with shear-driven Kelvin-Helmholtz vortices, and increased in likelihood with streamwise distance. At the flame base, isolated events were observed, which developed into rapidly burning flame kernels that were blown downstream. Further downstream, near-simultaneous spatially-distributed ignition events were observed, which appeared more like ignition sheets. The paper concludes with a broader discussion that considers generalising from the conditions considered here.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Large eddy simulation of lean blow-off in swirl-stabilized flame with the subgrid dissipation concept

The lean blow-off mechanism of the premixed swirl flame is numerically investigated by large eddy simulation (LES) with the subgrid dissipation concept (SDC) combustion model. Three simulated cases cover stable, near blow-off, and transient conditions. Compared with the experiment, the LES-SDC approach captures the flow and combustion features for stable and near blow-off conditions. More importantly, the predictions of the blowoff procedure and duration agree satisfactorily with the experiment, indicating that the LES-SDC approach is a promising tool for predicting strong, unsteady turbulent combustion processes. Further, the numerical results are used to investigate the blow-off mechanism. Two stages in the blow-off procedure are specified. The first is the necking and extinction of the downstream flame surface, and the second is the shrinking of the upstream flame surface. The blow-off mechanism is well explained by the theory of stretched flame extinction. At the end of the recirculation zone, the large negative radial velocity pushes the flame to the central line. The combustion process here can be abstracted as the stretched counter-flame of the reactant-reactant configuration. The excessive flame stretch dominates the flame extinction and triggers the blow-off event. The upstream flame resists the intense stretch with the help of hot product recirculation, and the combustion here can be idealized as the counter-flame of the reactant-product configuration. The alignment of the temperature gradient and flow velocity, together with the excessive stretch, clearly indicates the tendency of flame local extinction. A Damköhler number-based blow-off criterion is raised from the mean flow strain rate and laminar flame bulk extinction strain rate.

42 ENGINEERING↗
DOE OSTI2024

Quantifying the thermal effect and methyl radical production in nanosecond repetitively pulsed glow discharges applied to a methane-air flame

In this work, we investigated non-equilibrium plasma produced by nanosecond repetitively pulsed glow discharges applied across a lean premixed methane-air flame. The flame is stationary, axisymmetric, and laminar. The discharges are applied on the symmetry axis crossing the reactant gases, flame front, and product gases, allowing phase-locked averaged measurements and comparisons with axisymmetric numerical simulations. The thermal effect and methyl radical production are quantified in the discharge in the reactant gas region. One-dimensional, two-beam, hybrid, femtosecond-picosecond, coherent anti-Stokes Raman scattering is used to acquire spatial and temporal profiles of temperature and oxygen-to-nitrogen concentration ratio. Photo-fragmentation laser-induced fluorescence is used to acquire quantitative two-dimensional profiles of methyl radicals in the discharge providing the first quantitative imaging of methyl produced ahead of a flame by plasma-induced methane dissociation. The spatial profiles of temperature and oxygen-to-nitrogen concentration ratio are in steady state, indicating that individual discharges have an insignificant heating effect. Upper and lower bounds of the produced mole fraction of methyl radicals in the plasma are obtained due to uncertainties in the collisional quenching rates of excited state methylidyne radicals in the plasma. The discharges produce a maximum of 600–1100 ppm of methyl radicals upstream of the flame front within 25 ns. This amount is similar to the predicted methyl mole fraction for the flame without plasma and thus represents a significant chemical perturbation to the reactants upstream of the flame front. The produced methyl follows an exponential decay in the first microsecond after the discharge with a decay constant of 8 µs close to the flame, and 0.8 µs further from the flame. The decay then deviates from the exponential curve and the methyl persists for tens of microseconds. The results suggest that for the tested configuration, the thermal effect of individual discharges through fast gas heating is negligible, while active chemical species are produced in large quantities in the reactant gases, upstream of the flame front.

hybrid fs-ps CARS↗
DOE OSTI2024

Flame kinetics at scramjet-engine-relevant conditions: Role of prompt dissociation of weakly-bound radicals

Combustion in high-speed ram-based propulsion engines occurs under distinct thermodynamic conditions of high reactant temperatures (greater than 1000 K) and relatively low pressures (<5 atm). There is a lack of fundamental flame measurements at such conditions that result in adiabatic flame temperatures (T ad ) exceeding 2500 K. In this work, we have measured laminar flame speeds of oxygen-enriched CH 4 /oxidizer mixtures at sub-atmospheric conditions to probe kinetics at high T ad using the isobaric spherically expanding flame approach. Simulations with recent kinetic models revealed increasing differences between data and model predictions with increasing T ad , reaching up to 25 %. Kinetic analyses reveal that at the thermodynamic conditions in these O 2 -enriched flames, i.e., lower pressures and higher T ad , the effects of HCO prompt dissociation are accentuated. In addition to HCO, the prompt dissociations of CH 2 OH and C 2 H 5 are also considered. Here, the prompt dissociations of all three radicals were evaluated and their effects considered in flame speed simulations. Reaction path analysis for the present flames revealed that approximately half of the reaction flux for HCO formation undergoes prompt dissociation to H + CO. Furthermore, these analyses also revealed that the pathways and sensitive reactions are similar between oxygen-enriched fuel/oxidizer mixtures and preheated fuel/air mixtures, if both have similar T ad . Thus, flames of oxygen-enriched mixtures could be a surrogate to probe the flame chemistry of highly preheated mixtures at relatively low pressures that are often encountered in ram-based propulsion engine combustors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Turbulent burning velocity of lean premixed hydrogen/air flames at engine conditions: Effects of turbulence intensity and length scale

For turbulent lean premixed hydrogen flames with strong thermodiffusively instabilities, most previous studies have focused on the influence of turbulence intensity, whereas the role of turbulence length scale is less well understood. Here, this study addresses this gap by conducting direct numerical simulations (DNS) of statistically planar turbulent premixed flames for a lean (ϕ=0.35) hydrogen/air mixture under independently varied turbulence intensity (u') and length scale (l T ) at engine-relevant thermodynamics conditions. Results show that as u' increases, the flame front becomes increasingly wrinkled, forming smaller cellular structures. In contrast, l T variations do not significantly alter the size of these structures. For the turbulent burning velocity (S T ), the normalized S T (i.e., S T /S L , where S L is the laminar flame speed) increases linearly with u', driven by both enhanced flame surface wrinkling (i.e., increased A T /A L ) and enhanced local burning rate (i.e., increased I 0 ). However, increasing l T reduces I 0 , despite a continued increase in A T /A L , resulting in only a marginal increase in S T /S L . To reveal the underlying mechanisms, especially the decreasing trend of I 0 with l T , local flame dynamics analyses are performed. It is found that as l T increases, the interaction between thermodiffusive effects and turbulence weakens due to the reduced tangential strain rate, while the flame curvature remains largely unchanged. This suppresses local reactivity enhancement and thus decreases I 0 , In contrast, an increase in u' enhances the interaction by amplifying both curvature fluctuation and tangential strain rate, leading to increased local reactivity (increased I 0 ). Finally, based on the DNS data, several new scaling models are proposed for the three global properties, S T /S L , A T /A L , and I 0 , and showed improvements compared to existing models. These findings provide new insights into the flame-turbulence interactions in thermodiffusively unstable hydrogen flames. The DNS dataset is also useful for the development of turbulent combustion models applicable to practical engine simulations.

Engine-relevant condition↗
DOE OSTI2024

Temperature effect on turbulent burning velocity of lean premixed hydrogen/air flames

Hydrogen has drawn great attention in recent years as a carbon-free fuel. The turbulent burning velocity (S T ) is an important parameter for the design and modeling of hydrogen-fueled engines given the high propagation speed of hydrogen flames. It has been well documented that S T of hydrogen flames can be dramatically increased by thermo-diffusive effects which are sensitive to thermodynamic conditions. Previous studies have mainly focused on the pressure effect on S T of lean hydrogen flames, while the temperature effect has been largely ignored. Here, in the present study, the turbulent burning velocity for a lean hydrogen/air mixture over a wide range of temperatures (300–641 K) and pressures (1–15 atm) is investigated through direct numerical simulations of statistically planar turbulent premixed flames. Results show that the variation of normalized turbulent burning velocity (S T /S L , where S L is the laminar flame speed) with temperature and pressure is mainly controlled by the variation of the stretching factor I 0 . While S T /S L is only marginally dependent on temperature at the atmospheric pressure, it exhibits a decreasing trend with temperature at an elevated pressure (10 atm). This is associated with different temperature dependencies of flame surface area enlargement at the two different pressures, despite the monotonically decreasing trends of I 0 with temperature at both pressures. In addition, under engine-relevant conditions where the temperature and pressure increase simultaneously, the promotion effect of pressure is found to be largely canceled out by the suppression effect of temperature, leading to only a slight increase in I 0 and S T /S L . The observed trends are further explained through detailed flame dynamic analysis. Furthermore, I 0 at different temperatures and pressures is found to correlate very well with the enhancement of fuel consumption rate in the critically strained laminar flames. The present study elucidates the strong impact of temperature on S T of lean premixed hydrogen/air flames at elevated pressures and provides new insights into the modeling of S T , especially for engine-relevant conditions.

Wang, Yiqing [Argonne National Laboratory (ANL), A↗
DOE OSTI2025

Interactions of a Microdischarge with a Premixed Flame (Final Technical Report)

In this project we introduced an experimental platform that facilitates the study of the two-way interaction of plasma and flame, and the exploration of the impact of the spatial location of the discharge on its kinetics, in a controlled environment. The experimental platform is a mesoscale CH4/air premixed flame burner that also acts as a dielectric barrier discharge (DBD) operated by nanosecond pulsed voltage. A unique feature of this setup is that the DBD utilizes transparent electrodes, made of Indium Tin Oxide (ITO), to unlock optical access along the line-of-sight parallel to the dominant electric field. This platform is suitable to study both the forward problem (impact of plasma-on-flame), which manifests itself as a modified flame speed as well as flame wrinkling; and the backward problem (impact of flame-on-plasma), which includes plasma regime transitions, between microdischarges and uniform modes, driven by the flame passage. Prior work at MIT has focused on electrical measurements and direct imaging studies of the plasma-flame interaction through the ITO electrode. This project, which was awarded experimental runtime at the Low-temperature Plasma Research Facility (PRF) at Sandia National Laboratories, quantifies the flame-plasma interaction through temporally resolved measurement of key radicals (oxygen atom, O) produced by the nanosecond repetitively pused discharge (NRPD) in an individual microdischarge, using two-photon absorption laser-induced fluorescence (TALIF).

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗