Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FIGS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

First Results from Faint Infrared Grism Survey (Figs): First Simultaneous Detection of Ly Alpha Emission and Lyman Break From a Galaxy at Z =7.51

Galaxies at high redshifts provide a valuable tool to study cosmic dawn, and therefore it is crucial to reliably identify these galaxies. Here, we present an unambiguous and first simultaneous detection of both the Lyman-Alpha emission and the Lyman break from a z = 7.512 +/- 0.004 galaxy, observed in the Faint Infrared Grism Survey (FIGS). These spectra, taken with G102 grism on Hubble SpaceTelescope (HST), show a significant emission line detection (6 Sigma) in two observational position angles (PA), with Lyman-Alpha line flux of 1.06 +/- 0.19 x 10(exp -17) erg s(exp -1) cm(exp -2). The line flux is nearly a factor of four higher than in the archival MOSFIRE spectroscopic observations. This is consistent with other recent observations implying that ground-based near-infrared spectroscopy underestimates total emission line fluxes, and if confirmed, can have strong implications for reionization studies that are based on ground-based Lyman-Alpha measurements. A 4-Alpha detection of the NV line in one PA also suggests a weak Active Galactic Nucleus (AGN), and if confirmed would make this source the highest-redshift AGN yet found.These observations from the Hubble Space Telescope thus clearly demonstrate the sensitivity of the FIGS survey, and the capability of grism spectroscopy to study the epoch of reionization.

Faint Galaxy Z=7.51↗

Sm-Nd dating of Fig Tree clay minerals of the Barberton greenstone belt, South Africa

Sm-Nd isotopic data from carbonate-derived clay minerals of the 3.22-3.25 Ga Fig Tree Group, Barberton greenstone belt, South Africa, form a linear array corresponding to an age of 3102 +/- 64 Ma, making these minerals the oldest dated clays on Earth. The obtained age is 120-160 m.y. younger than the depositional age determined by zircon geochronology. Nd model ages for the clays range from approximately 3.39 to 3.44 Ga and almost cover the age variation of the Barberton greenstone belt rocks, consistent with independent evidence that the clay minerals are derived from material of the belt. The combined isotopic and mineralogical data provide evidence for a cryptic thermal overprint in the sediments of the belt. However, the highest temperature reached by the samples since the time of clay-mineral formation was <300 degrees C, lower than virtually any known early Archean supracrustal sequence.

Non-NASA Center↗

FIGS: spectral fitting constraints on the star formation history of massive galaxies since the cosmic noon

We constrain the stellar population properties of a sample of 52 massive galaxies – with stellar mass log (M(s)/M(⊙)) ≳ 10.5 – over the redshift range 0.5 < z < 2 by use of observer-frame optical and near-infrared slitless spectra from Hubble Space Telescope’s ACS and WFC3 grisms. The deep exposures (∼100 ks) allow us to target individual spectra of massive galaxies to F160W = 22.5 AB. Our spectral fitting approach uses a set of six base models adapted to the redshift and spectral resolution of each observation, and fits the weights of the base models, including potential dust attenuation, via a Markov Chain Monte Carlo method. Our sample comprises a mixed distribution of quiescent (19) and star-forming galaxies (33). We quantify the width of the age distribution (Δt) that is found to dominate the variance of the retrieved parameters according to principal component analysis. The population parameters follow the expected trend towards older ages with increasing mass, and Δt appears to weakly anticorrelate with stellar mass, suggesting a more efficient star formation at the massive end. As expected, the redshift dependence of the relative stellar age (measured in units of the age of the Universe at the source) in the quiescent sample rejects the hypothesis of a single burst (aka monolithic collapse). Radial colour gradients within each galaxy are also explored, finding a wider scatter in the star-forming subsample, but no conclusive trend with respect to the population parameters.

Ignacio Ferreras↗

Thermodynamic and Diffusion Model Estimates on Metamorphic Temperatures and Timescales for Basaltic Eucrite GRA 98098

Introduction: HED meteorites are thought to rep-resent igneous rocks from Vesta’s basaltic crust and preserve evidence of early crustal metamorphism. Determining the temperatures and timescales of thermal metamorphism is important for reconstructing crustal evolution in the early solar system. Here, we study basaltic eucrite Graves Nunataks (GRA) 98098, which has been identified as a highly metamorphosed eucrite [1]. We present new estimates on metamorphic temperatures determined via thermodynamic modeling as well as the initial results from diffusion models constraining timescales of thermal metamorphism. Sample Description: GRA 98098 is an unbrecciated eucrite with a granoblastic plagioclase and pyroxene mineralogy. Millimeter to cm-long lathes of tridymite cross-cut and poikilitically enclose plagioclase and pyroxene [1,this work]. Pyroxene grains have exsolved into Ca-rich (~Wo38En29Fs33) and Ca-poor (~Wo4.5En36Fs59.5) lamellae. Both unzoned and zoned plagioclase grains are observed. Unzoned plagioclase grains are found solely with tridymite laths. These grains have ~An92 compositions. The cores of the zoned plagioclase grains have the same composition and thin, relatively sodic rims (~An67), (Fig. 1). The bulk sample is unusually enriched in highly in-compatible elements and has one of the most fractionated REE patterns reported [1]. Maximum metamorphic temperatures of 985±78°C have been estimated using two-pyroxene thermometry [2]. Methods: Thermodynamic modeling. Thermodynamic models were constructed using the software Perple_X, which employs a Gibbs free energy minimization in order to determine the most stable phase assemblage for a given bulk rock composition [3]. Bulk composition was calculated using mineral com-positions acquired via EMPA (this study) and the observed abundancies present in the thin section. Two bulk compositions were estimated; 1) includes all phases present in the thin section, (assumes that all phases are present during metamorphism), 2) excludes tridymite from the bulk calculation (assumes that tridymite was not present during metamorphism). In order to determine whether metamorphic equilibria was achieved and estimate temperatures of metamorphism, we compared measured pyroxene compositions with thermodynamically predicted compositions [4, Fig. 2]. Diffusion Modeling. Several time-temperature de-pendent diffusion profiles were calculated in order to determine the best match for XAn chemical profiles observed at the edges of the zoned plagioclase (Fig. 3). We assumed that the start condition was a stepwise gradient at the plagioclase/pyroxene interface. We also assumed an average diffusion coefficient (D) and a constant temperature using the equation in [5]. D was determined for two temperatures (T = 1060ºC; near eucrite solidus [6] and T = 985ºC; metamorphism reported in [4]) and then XAn was calculated as a function of distance from plagioclase core to rim using an error function solution to Fick’s second law. Results: Thermodynamic model results are summarized in Fig. 2. For a bulk composition that includes all phases in the thin section, pyroxene endmember compositions plot in the following temperature ranges: Fs ~660-860ºC, En~1000ºC & 1150ºC, and Wo~760-900ºC (Fig. 2a). For a bulk composition that excludes tridymite from the peak metamorphic assemblage (i.e., the bulk composition minus the contribution from tridymite), a temperature range could not be determined for the Fs component of pyroxene. For Wo, T~760-900ºC and En, T~1000ºC & 1150ºC (Fig. 2b). Fig. 3 summarizes the diffusion model results. For T = 1060°C & 985°C, the most appropriate time interval was estimated based on which diffusion curve most matched (solid lines, Fig. 3) the EMPA data. For T = 1060°C, the best looking match was t = 500 ka. For T = 985°C, the best match was t = 7 Ma. Discussion and future work: Temperature estimates from thermodynamic models are not conclusive because the temperature ranges determined for pyroxene endmember stability do not overlap (colored fields in Fig. 2), thus implying that there is disequilibrium between pyroxene crystals and the bulk composition considered [4]. Thus, additional exploration is needed to define a metamorphically equilibrated do-main that accurately records peak temperature. The utility of defining metamorphically equilibrated do-mains to improve the accuracy and level of detail elucidated regarding the petrogenetic history of metamorphose samples has been demonstrated previously [4,7]. We suggest that in the case of Fig. 2a, the thin section composition is not representative of the length scales over which metamorphic equilibrium was achieve and in the case of Fig. 2b, the assumption that tridymite was not present during metamorphism was incorrect. However, results from thermodynamic models can provide insight into the relative timing of mineral and compositional textures. For example from texture alone, it is unclear whether tridymite was igneous in origin and represents the last bits of melt in a crystallizing magma chamber, or if it formed during (and possibly initiated) open system thermal metamorphism. The latter could be consistent with a partial melt hypothesis [8,9] while the former implies that simple fractional crystallization can yield the textures present in GRA 98098. The lack of coincidence be-tween pyroxene endmember compositions in Fig. 2b suggest that the bulk composition minus tridymite was not the assemblage in equilibrium with the pyroxene, suggesting that tridymite was present during metamorphism and formed during igneous crystallization. We conclude that the development of the Na-rich plagioclase rims likely occurred during or immediately after peak thermal metamorphism, because eucrites of similar metamorphic grade and texture have unzoned plagioclase (~An92) [2,4,8], and Na zoning is only observed in the plagioclase not included in the tridymite. This suggests that the zoning formed after tridymite formation, and therefore after igneous crystallization. Thus, the timescales calculated via diffusion modeling possibly represent the time interval over which thermal metamorphism occurred. Cooling rates approximated for the Vestan crust predict that the crust cooled below 300°C around 35-40 Ma after formation[10]. This is consistent with our modeling results that predict formation of the Na rich plagioclase rims occurring at higher temperatures over a period of 0.5 to 7 Ma years. Future work. Additional thermodynamic modeling work will focus on selecting an equilibrated bulk rock domain in which to elucidate metamorphic conditions. Diffusion models currently provide a minimum time-scale, since diffusion slows down as the system cools. Future work with will focus on integrating cooling into the diffusion models and constraining the depth at which thermal metamorphism occurs because it could be used to determine whether the range of time-scales calculated for thermal metamorphism are consistent with the geologic environment.

J S Gorce↗

Surface Habitat Systems

The Surface Habitat Systems (SHS) Focused Investment Group (FIG) is part of the National Aeronautics and Space Administration (NASA) Johnson Space Center (JSC) effort to provide a focused direction and funding to the various projects that are working on human surface habitat designs and technologies for the planetary exploration missions. The overall SHS-FIG effort focuses on directing and guiding those projects that: 1) develop and demonstrate new surface habitat system concepts, innovations, and technologies to support human exploration missions, 2) improve environmental systems that interact with human habitats, 3) handle and emplace human surface habitats, and 4) focus on supporting humans living and working in habitats on planetary surfaces. The activity areas of the SHS FIG described herein are focused on the surface habitat project near-term objectives as described in this document. The SHS-FIG effort focuses on mitigating surface habitat risks (as identified by the Lunar Surface Systems Project Office (LSSPO) Surface Habitat Element Team; and concentrates on developing surface habitat technologies as identified in the FY08 gap analysis. The surface habitat gap assessment will be updated annually as the surface architecture and surface habitat definition continues to mature. These technologies are mapped to the SHS-FIG Strategic Development Roadmap. The Roadmap will bring to light the areas where additional innovative efforts are needed to support the development of habitat concepts and designs and the development of new technologies to support of the LSSPO Habitation Element development plan. Three specific areas of development that address Lunar Architecture Team (LAT)-2 and Constellation Architecture Team (CxAT) Lunar habitat design issues or risks will be focused on by the SHS-FIG. The SHS-FIG will establish four areas of development that will help the projects prepare in their planning for surface habitat systems development. Those development areas are the 1) surface habitat concept definition, 2) inflatable surface habitat development, and 3) autonomous habitat operations, and 4) cross-cutting / systems engineering. In subsequent years, the SHS-FIG will solicit a call for innovations and technologies that will support the development of these four development areas. The other development areas will be assessed yearly and identified on the SHS-FIG s Strategic Development Roadmap. Initial investment projects that are funded by the Constellation Program Office (CxPO), LSSPO, or the Exploration Technology Development Projects (ETDP) will also be included on the Roadmap. For example, in one or two years from now, the autonomous habitat operations and testbed would collaborations with the Integrated Systems Health Management (ISHM) and Automation for Operations ETDP projects, which will give the surface habitat projects an integrated habitat autonomy testbed to test software and systems. The SHS-FIG scope is to provide focused direction for multiple innovations, technologies and subsystems that are needed to support humans at a remote planetary surface habitat during the concept development, design definition, and integration phases of that project. Subsystems include: habitability, lightweight structures, power management, communications, autonomy, deployment, outfitting, life support, wireless connectivity, lighting, thermal and more.

Kennedy, Kriss J.↗

Fluvial Channel Networks as Analogs for the Ridge-Forming Unit, Sinus Meridiani, Mars

Fluvial models have been generally discounted as analogs for the younger layered rock units of Sinus Meridiani. A fluvial model based on the large fluvial fan provides a possibly close analog for various features of the sinuous ridges of the etched, ridge-forming unit (RFU) in particular. The close spacing of the RFU ridges, their apparently chaotic orientations, and their organization in dense networks all appear unlike classical stream channel patterns. However, drainage patterns on large fluvial fans low-angle, fluvial aggradational features, 100s of km long, documented worldwide by us provide parallels. Some large fan characteristics resemble those of classical floodplains, but many differences have been demonstrated. One major distinction relevant to the RFU is that channel landscapes of large fans can dominate large areas (1.2 million km2 in one S. American study area). We compare channel morphologies on large fans in the southern Sahara Desert with ridge patterns in Sinus Meridiani (fig 1). Stream channels are the dominant landform on large terrestrial fans: they may equate to the ubiquitous, sinuous, elongated ridges of the RFU that cover areas region wide. Networks of convergent/divergent and crossing channels may equate to similar features in the ridge networks. Downslope divergence is absent in channels of terrestrial upland erosional landscapes (fig. 1, left), whereas it is common to both large fans (fig. 1, center) and RFU ridge patterns (fig 1, right downslope defined as the regional NW slope of Sinus Meridiani). RFU ridge orientation, judged from those areas apparently devoid of impact crater control, is broadly parallel with the regional slope (arrow, fig. 1, right), as is mean orientation of major channels on large fans (arrow, fig. 1, center). High densities per unit area characterize fan channels and martian ridges reaching an order of magnitude higher than those in uplands just upstream of the terrestrial study areas fig. 1. In concert with several other regional features, these morphological similarities argue for the RFU as a possibly fluvial unit.

Wilkinson, M. J.↗

Trace Elemental Abundances in Calcium-Aluminum-Rich Inclusions in CV Chondrites

Introduction: Calcium-aluminum-rich inclusions (CAIs), are the first formed solids that define the age of the Solar System [1,2]. CAIs are thought to have condensed from nebular gas [3,4] within the first <1 Ma of Solar System formation [5,6]. CAIs have experienced numerous early Solar System processes including condensation, evaporation, melting, recrystallization, and aqueous alteration [e.g., 7]. The chemical, mineralogical, and textural diversity among CAIs results from a range of chemical and physical processes recorded during nebular and parent body epoch. This study aims to explore the mineralogical, textural, and chemical compositions of CAIs including the trace elemental abundances in CAI phases to determine the early Solar System processes recorded in them. Samples and Analytical Methods: We analyzed one CAI each from CV3 chondrites Northwest Africa (NWA) 5508 designated as ‘Saguaro’, and Northwest Africa (NWA) 12772 designated as ‘Hoopoe’. Back-scatter electron (BSE) images were collected using a Phenom XL scanning electron microscope (SEM) at the Lunar and Planetary Institute (LPI) and the JEOL JXA-8530F electron probe microanalyzer (EPMA) at Johnson Space Center (JSC)-NASA. Additionally, energy dispersive X-ray spectrometry (EDS) elemental maps of select areas for these samples were collected using a 15.0kV beam energy and a 40µA emission current. Using the EPMA, wavelength-dispersive X-ray spectroscopy (WDS) quantitative data were collected. In-situ trace element measurements for both CAIs were determined at JSC-NASA using a Photon Machines 193nm laser ablation system and a Thermo-Scientific Element-XR inductively coupled plasma mass spectrometer (ICP-MS). Analyses consisted of 30s ablations at 10Hz, spot sizes of 20-25µm, and a fluence of 6.0 J/cm2 for anorthite and melilite, and a 3.5 J/cm2 fluence for all other phases. NIST612 was used to correct for instrument drift, while BHVO-2g was used as a primary calibration standard. BCR-2g and in-house mineral standards were regularly measured as unknowns to ensure accuracy. Results: Saguaro is a coarse-grained CAI, ~11 x 6 mm in dimensions. Saguaro contains spinel, Al-rich pyroxene, anorthite, Mg-rich melilite, and minor perovskite in its interior and is therefore classified as a Type B CAI. Individual melilite grains shows normal compositional zoning with an Ak content ranging from ~24 to 54 with no apparent trend from the core to the edge of the CAI. The spinel appears euhedral and occurs both as clusters and as spinel palisades [8]. Two rim sequences surround most of the sample: the inner rim being a Wark-Lovering (WL) rim (~10-35 µm) containing pyroxene, spinel, and melilite (or anorthite), and the outer rim is a finer-grained, thicker (~100 µm), accretionary rim (Fig. 1). The mineral phases in Saguaro record an overall flat REE pattern with an average negative Eu anomaly in pyroxene, and an average positive Eu anomaly in anorthite and melilite respectively. Anorthite, melilite, and pyroxene have a minor depletion in Tm (Fig. 2). The Hoopoe CAI is a compact, coarse-grained ~6 × 4 mm in size. The major mineralogy includes hibonite, spinel, melilite, anorthite, and perovskite. Therefore, it is classified as a compact transitional type A and B. (?)zoning was observed in some hibonites. Individual melilite grains show both reverse and normal zoning, where the Ak content ranges from ~6- to 28. Melilite shows two distinct textures. One texture consisted of smooth melilite that appeared homogenous, while the second appeared to consist of many fine fractures. The spinel also often appears clustered. The WL-rim sequence surrounding Hoopoe is ~25 µm thick and composed of spinel, perovskite, hibonite, and melilite/anorthite. It is then partially surrounded by an outer accretionary rim (~75µm). Like before, refractory metal nuggets appeared concentrated near the WL rims. Other metal assemblages rich in Fe and Ni were also observed. All major mineral phases in Hoopoe display relatively flat REE patterns, except for varying Eu and Tm between phases (Fig. 2). There is a prominent negative Eu anomaly in perovskite and an average positive Eu anomaly in spinel, anorthite, and hibonite respectively (Fig. 2, 3). The mixed phases along the rim of the CAI also display a negative Eu anomaly, and all phases the CAI were depleted in Pb. Discussion: The CV3 CAIs analyzed in this study were classified based on their mineralogy and textures into Type A versus Type B CAIs [10]. Hibonite appears to be pseudomorphically replacing the spinel, (i.e., is hibonite in composition, but appears in the shape of spinel). Spinel palisades. The presence of spinel palisades present in Saguaro are consistent with the melting and recrystallization experienced by this CAI. Trace elemental analyses. Saguaro and Hoopoe display similar trace element patterns to each other, with both appearing generally flat, with anomalies in Eu, and Tm. Melilite and anorthite display positive Eu anomalies in both CAIs, in addition to the hibonite in Hoopoe (Fig. 2). The phases that are depleted in Eu are pyroxene and perovskite in both Saguaro and Hoopoe, respectively (Fig. 3). Given that Eu is volatile in reducing environments [11], this could possibly indicate reducing conditions at the time anorthite and melilite crystallized, with the gas they formed from containing Eu. As these CAIs continued to form, this gas as a result would become depleted in Eu. This also could be supported by the propensity of anorthite and melilite to take up Eu from its surroundings and incorporate it into their structure [12]. In addition, analyzing the assemblage of the phases in the Saguaro, melilite and anorthite (Eu enriched) often surround the pyroxene (Eu depleted) as they are crystallized. This intergrowth of phases and the proximity of the phases would support that the Eu is being incorporated into some phases, preventing it from incorporating into other. Trace elemental analyses of the CAI rims will be evaluated in more detail, as they are complicated by the transient signal being composed of a mixture of mineral phases. Broadly, however, the patterns in the rims of both CAIs are comparable to each other, and for Hoopoe, to the mixed phase patterns in the core (Fig. 3). Other studies have found that CAI rims can be depleted in Ce and Yb [13], however we did not observe these anomalies in the two CAIs discussed here. Given their similarity, the trace elemental analyses of the mixed interior (i.e. core) and rim phases could be interpreted as forming from similar, if not the same, reservoirs. The REE abundance between the rim and core of Hoopoe are also similar, indicating they may have formed from a gas of the same or similar composition. Acknowledgments: We thank the ASU Center for Meteorite Studies for loaning the samples used in this work and Tabb Prissel for his assistance with the analysis. Mouti Al-Hashimi thanks Sam Crossley and Cyrena Goodrich for their help with the LPI SEM training. This work was supported by the LPI Summer Intern Program in Planetary Science and the LPI Cooperative Agreement. References: [1] Connelly J.N. (2012) Science, 338, 651-655. [2] MacPherson G. J. (2014) Treatise on Geochem., 2, 139-179. [3] Grossman L. (1972) GCA, 36, 597-619. [4] Ebel, D.S. (2006) Meteorites and the Early Solar System II (D. S. Lauretta & H. Y. McSween, Eds.) 253-277. [5] MacPherson G. J. (2012) Earth Planet. Sci. Lett., 331-332, 43-54. [6] MacPherson G.J. (2017) GCA, 201, 65-82. [7] Krot A.N. (1995) Meteoritics & Planet. Sci., 30, 748-775. [8] Wark and Lovering (1982) GCA, 46, 2595-2607. [9] Palme H. and Jones A. (2003) Treatise on Geochemistry (H. D. Holland and K. K. Turekian Eds.), 1, 41-61. [10] Grossman L. (1980) Ann. Rev. Earth Planet. Sci., 8, 559-608. [11] Floss C. et al. (1996) GCA, 60, 1975-1997. [12] Mason B. and Martin P. M. (1974) Earth Planet. Sci. Lett., 22, 141-144. [13] Wark B. and Boynton W. V. (2001) Meteoritics & Planet. Sci., 36, 1135-1166.

X Mouti↗

4.32 Billion Year Old Impact Melts at Apollo 14: Dating the Procellarum Basin?

Introduction: Recent work has improved our understanding of lunar crustal structure and basin evolution on the Moon, but its early impact history and implications for solar system dynamics remain poorly established [1,2]. In particular, there is a derth of absolute ages, especially for the period >4.0 Ga, that could be related to basin-forming events. Here we present U-Pb isotopic data for Zr-rich minerals found in impact-melt fragments from Apollo 14 soil sample 14163 that, when combined with previously published data, dates an impact event at 4324±15 Ma. The compositions and ages of these impact-melt fragments provide unique information about the timing of early impact events and the composition of the lunar crust. Results: Fourteen rocklets ranging in size from 1 to 3 mm were extracted from soil 14163. Most are impactmelt rocks with 10-30% clasts of mostly pyroxene and plagioclase (100 to 500 μm) in a crystalline matrix. Textures of the matrix vary from subophitic, formed by intergrowths of 10-20 μm plagioclase and pyroxene crystals, to poikilitic, with plagioclase and pyroxene reaching 20-50 μm size. Some fragments that contain no visible clasts have similar textures are also interpreted as impact-melt rocks. All fragments contain notably large proportions of euhedral to subhedral ilmenite, zircon, apatite/merrillite and less abundant zirconolite and baddeleyite in the melt matrices. These grains often form intricate intergrowths with each other and rock-forming minerals, indicating their crystallization from the melt (Fig. 1). However, some slightly larger (~50 μm) zircon and phosphate grains can be interpreted as relict clasts based on their granular textures and relationships with the surrounding phases (Fig. 1). This implies that zircon and phosphate minerals were present in the target rocks. Some of these grains were profoundly remelted during the impact, which resulted in an oversaturation of the melt in Zr and P and crystallization of new grains of Zrrich minerals and phosphates during melt solidification. The presence of zircon and phosphates indicates that the melts were significantly enriched in KREEP components and ties their provenance to the Procellarum- KREEP Terrane (PKT) [3]. Combined U-Pb zircon data obtained for all fragments form two main clusters on a concordia diagram (Fig. 2), between about 4.3 and 3.9 Ga. Phosphate data mostly concentrate on the younger end of this age range but some analyses are almost as old as the older zircon grains (Fig. 2). Figure 1: Zircon (Zr) and phosphate (Apt; Mer) grains in impact melt fragments from Apollo 14 soil 14161. A-zircon grains crystallized from impact melt; B-phosphate grain inherited from the target; C- granular zircon grains Our interpretation of these data is that all U-rich minerals experienced variable resetting of the U-Pb system, with phosphate, where closure temperature is significantly lower than that in zircon, affected more profoundly by Pb loss than zircon. Our best estimate of the time of formation of zircon and phosphate is based on statistically valid analysis of grains interpreted texturally as grown from the impact melt (Fig. 2). Ten of these analyses define an age of 4324±15 Ma (MSWD=3.0, probability of fit P=0.002). Our best estimate for the time of resetting is obtained by combining data from phosphates that are statistically indistinguishable from 3.9 Ga within the analytical uncertainties. This group is represented by 18 analyses of 15 phosphate grains from different fragments (Fig. 2) and defines an age of 3922±6 Ma (MSWD=1.2, P=0.23). Conversely, a minimum age of the target lithologies, remelted in the impact that produced the rocklets studied here (Fig. 2), can be determined from the five oldest analyses of zircon clasts at 4338±13 Ma (MSWD=1.5, P=0.2), which is indistinguishable from the age of the impact melt within the uncertainties. The obtained ages, combined with textural evidence, imply that the impact melt was formed at 4324±15 Ma, and that it occurred in a zircon-rich target with a minimum age of 4338±13 Ma. Further reworking occurred during a second impact event at 3922±6 Ma. Discussion: The younger age of 3922±6 Ma can be interpreted as the time of the Imbrium impact. The older age of 4324±15 Ma would then be the time of formation of the impact melt, which was then caught in the Imbrium ejecta either at the Apollo 14 landing site or within the target rocks of the Imbrium impact. The presence of abundant accessory phases such as zircons and phosphates is consistent with a substantial KREEP component in the analyzed particles. The current distribution of KREEP on the lunar surface appears to be strongly influenced by Imbrum ejecta [4] so interpretation of the 4.32 Ga age depends in part on assumed structure of the pre-impact crust and distribution of KREEP within the crust. If KREEP was present only in the deep crust at 4.32 Ga, then a basin-scale impact possibly analogous to Imbrium or larger may be necessary to excavate a KREEPy impact melt at this time. However, if KREEPy materials were present closer to the surface perhaps due to redistribution related to Mg-suite magmatism, then smaller impacts might be able to rework KREEPy compositions at shallower depths. The coherence of the data on the particles analysed here suggests a large volume of melt that has been preserved since 4.32 Ga, consistent with a large impact event. Relict zircons and mineral clasts suggests that the igneous crust in the vicinity of this impact was well developed by at least 4.34 Ga, similar to the model age of KREEP and older than the isochron ages of many Mg-suite cumulates [5]. A problem that confronts all lunar sample studies using the current collection is that the pre-Imbrium geology of the PKT (the source of these 4.32 Ga impact melts) is not well constrained. The South Pole-Aitken basin contains regions that are moderately enriched in Th, but its ejecta is Th-poor [6]; therefore these A14 fragments are probably not SPA ejecta. Alternatively, these fragments may represent formation of a hypothesized Procellarum basin [7] although the lack of a clearly defined basin ejecta signature is a potential problem with that interpretation. In any case, they provide a younger limit on the age of lunar differentiation and formation of KREEP within the lunar crust. Figure 2: U-Pb data for zircon and phosphate grains from impact melt fragments. A-all data; B-data used for age calculations. References: [1] Orgel C., Michael G., Fassett C. I., van der Bogert C. H., Riedel C., Kneissl T., and Hiesinger H. (2018) J. Geophys. Res. Planets 123, 748- 762. [2] Evans A. J., Andrews-Hanna J. C., Head J. W., Soderblom J. M., Solomon S. C., and Zuber M. T. (2018) J. Geophys. Planets. 123, 1596-1617. [3] Jolliff, B.L., Gillis, J.J., Haskin, L.A., Korotev, R.L. and Wieczorek, M.A. (2000) J. Geophys. Res: Planets 105, 4197-4216. [4] Haskin L. A. (1998) J. Geophys. Res. Planets 103, 1679-1689. [5] Borg L.E., Gaffney A.M., and Shearer C.K. (2015) MAPS 50, 715-732. [6] Moriarty, D.P., Watkins, R.N., Valencia, S.N., Kendall, J.D., Evans, A.J., Dygert, N. and Petro, N.E. (2021) J. Geophys. Res. Planets 126. [7] Zhu, M.H., Wünnemann, K., Potter, R.W., Kleine, T. and Morbidelli, A. (2019) J. Geophys. Res: Planets 124, 2117-2140

M D Norman↗

Higher Order Chemistry Models in the CFD Simulation of Laser-Ablated Carbon Plumes

Production of single-walled carbon nanotubes (SWNT) has taken place for a number of years and by a variety of methods such-as laser ablation, chemical vapor deposition, and arc-jet ablation. Yet, little is actually understood about the exact chemical kinetics and processes that occur in SWNT formation. In recent time, NASA Johnson Space Center has devoted a considerable effort to the experimental evaluation of the laser ablation production process for SWNT originally developed at Rice University. To fully understand the nature of the laser ablation process it is necessary to understand the development of the carbon plume dynamics within the laser ablation oven. The present work is a continuation of previous studies into the efforts to model plume dynamics using computational fluid dynamics (CFD). The ultimate goal of the work is to improve understanding of the laser ablation process, and through that improved understanding, refine the laser ablation production of SWNT. Fig. 1 shows a basic schematic of the laser-ablation oven at NASA-JSC. Construction of the facility is simple in concept. Two concentric quartz tubes of 1.5 mm thickness form the inner and outer tubes with inside diameters of 2.2 and 5.08 cm respectively. At one end of the inner tube are located two 60 Hz pulsed lasers operating at 1064 nm and 532 nm wavelength with beam diameters of 5 mm aligned coaxially with the longitudinal axis of the inner quartz tube. For standard nanotube production runs, a 10 ns 532 nm pulse is followed 50 ns later by a 10 ns 1064 nm pulse. Each pulse is of 300 mJ energy. A target of carbon graphite with approximately 1% nickel and cobalt catalysts is located at the other end of the inner quartz tube. In the ordinary processing of SWNT, a base flow of 100 sccm of argon is maintained from the laser location and exits past the carbon target at a pressure of 66.7 kPa. These conditions yield a baseline mass flow through the chamber of 2.723x10(exp -6)kg/s of argon. The whole oven facility is heated to a temperature of 1473 K prior to nanotube production runs. Upon laser irradiation, part of the carbon target ablates immediately and forms a carbon vapor plume that penetrates into the argon base flow towards the laser initially at supersonic velocities. In the previous studies either a single carbon species, C3, was used to model the plume development, or a simplified 11 species carbon model reduced down from the Krestinin and Moravsky model for full fullerene chemistry was used. While both of these options yielded significant results, it was felt that the actual chemistry occ&g in the carbon plume might have a greater affect on the plume than assumed. Indeed, in the earlier attempts at modeling the carbon plume, several thermophysical characteristics could never be matched to experimental observations of plume development - mainly the propagation distance of the plume itself. In the present study, two additional chemistry models will be used to duplicate the previous studies simulations of the carbon plume. The first chemistry model used in this study is again a reduced form of the Krestinin and Moravsky rates. However the highest order carbon species allowed has been increased from C6 to C30 - therefore allowing the simulation of up to a half of the standard C60 fullerene. The second chemistry model investigated is a reduced form of a full carbon nanotube model developed at NASA-JSC. The C30 studies have already been accomplished at the present time, and the reduced SWNT model studies are currently underway. To pursue the current study, one sacrifice had to be made in that the simulation grid spacing had to be increased from 0.5 mm spacing to 1 mm spacing for the sake of computational efficiency since computational effort is proportional to the square of the number of grid points multiplied by the number of species considered. propagation that is far more in line with the experimental results observed by Puretzky et al as shown in Fig. 2. e C6 studies had yielded a far greater propagation in previous studies. In addition, chemical species development with the C30 model indicates that many higher order carbon species are produced outside of the plume proper (indicated by plotting contours of the background argon concentrations in Fig. 3) - this result was not observed in previous studies. In fact, some species primarily occurred outside of the plume itself - as shown for C27 in Fig. 4 when it is compared to Fig. 3. It could be asserted that this has occurred because all of the C27 in the plume had already been consumed in the formation of C30, but this does not seem to be indicated over time. Several other factors that arose in the previous studies have also been made more clear by the use of the higher order chemical models - one being that the use of c6 as an indicator species was mistaken. C6 is the only carbon species in the previous studies that was not injected into the flowfield as a boundary condition; it was therefore hoped that this species would provide insight into the formation of higher order carbon species for comparison to full SWNT production. But, when the plot of total mass in the plume is examined on a species by species basis in Fig. 5, it is seen that Cg was a fairly insignificant contributor to the total carbon mass in the plume and would not provide information on higher order carbon formation. the thermophysical characteristics of the carbon plume as well as simulate the carbon plume using the reduced SWNT model to provide an even better simulation of full chemistry effects upon plume propagation.

Scott, C. D.↗

Understanding the Space Weathering of Mercury Through Laboratory Experiments

Introduction: Airless surfaces across the solar system are continually modified by energetic particles from solar wind and micrometeoroid bombardment [1,2]. This process is known as space weathering, and it alters the chemical, microstructural, and optical properties of surface regoliths on airless bodies, including Mercury. On the Moon and S-type asteroids, the reflectance spectral signatures of space weathering include reddening (increasing reflectance with increasing wavelength), darkening (lowering of reflectance), and the attenuation of characteristic absorption bands [2]. Such spectral changes are driven by the production of Fe-bearing nanoparticles(npFe) through both solar wind irradiation and micrometeoroid bombardment. While our understanding of space weathering for the Moon and near-Earth S-types asteroids is advanced, insight into how these processes operate on other planetary bodies is limited. In particular, Mercury experiences a uniquely intense space weathering environment than planetary counterparts at 1 AU, including a moreintense solar wind flux and higher velocity micrometeoroid impacts [4]. Additionally, Mercury has a surface composition unique in the inner solar system, including regions of the surface with very low albedo known as the low reflectance material (LRM), which is enriched in carbon, likely graphite, up to 4wt.% [5].In addition, the concentration of Fe across Mercury’s surface islow (<2 wt.%) compared to the Moonor S-type asteroids asteroids[6]. Our understanding of the effects of space weathering on C-rich and Fe-poor phases is limited. Since Fe plays a critical role inthe development of space weathering characteristicson other airless surfaces(e.g., npFe), its limited availability may significantly affect the development of space weathering features in Mercury surface materials. We can simulate space weathering processes in the laboratory to explore their effects on the microstructural, chemical, and spectral characteristics of Mercury surface materials[7]. Here we used pulsed laser irradiation to simulate the short duration, high-temperature events associated with micrometeoroid impacts. We performed coordinated analyses including reflectance spectroscopy and electron microscopy to investigate the spectral, chemical, and microstructural changes in these mercurian analog samples. Methods: For these experiments, we usedforsteritic olivine with varying FeOcontents, a mineral phase proposed to be abundant on the surface of Mercury. We mixed each sample with graphite to simulate LRM regions of the surface. Wesynthesized the olivinesamplesat 1-bar at NASA’s Johnson Space Centerand prepared pressed powder pellets for laser irradiation [8].We prepared three samples, each with a base layer of olivineto maintain structural integrity and topped witha surface layer containing the graphite-olivine mixture: 1) Sample SC-001 San Carlos olivine(Fo90.91),2)Sample F-S-002 with0.05 wt.% FeO olivine, and 3) F-T-004 with 0.53 wt.% FeO olivine. Each sample was mixed with 5 wt.% powdered graphite and had grain sizes ranging from 45to 125μm. We irradiated each sample usinga pulsed Nd-YAG laser, (l=1064 nm, ~6 ns pulse duration, energy of 48 mJ/pulse) while undervacuumat Northern Arizona University. The laser was rastered1x and then 5x over the surfaceof each sample to simulate progressive space weathering. We collected in situreflectance spectra from the samples after each laser pulse witha Nicolet IS50 Fourier-Transform Infrared spectrometer (lfrom 0.65-2.5 μm). We used an FEI Nova NanoSEM200scanning electron microscope (SEM) and a Hitachi TM4000 Plus benchtop SEM at Purdue University to image the surface morphology and topography of the samples. We extracted thin sections for analysis in the transmission electron microscope(TEM)using the FEI Helios NanoLab 660 focused ion beam (FIB) SEM at the University of Arizona.We performed analysis of the microstructural and chemical characteristics of the samples using the 200 keV JEOL 2500 scanning TEM at Johnson Space Center. Reflectance Spectroscopy Results:Reflectance spectra for each sample are shown in Fig. 1.SC-001:The spectrum of the unirradiated sample exhibits a weak 1.0 μm absorption feature, associated with Fe2+in the olivine,and low overall reflectance (Fig. 1a). Thereflectance and the depth of the absorption band increases after 1x laser raster but are at their lowest after 5x laser rasters.F-T-004:The unirradiated sample has a blue-sloped spectrum with low reflectance without identifiable absorption features (Fig. 1b). With progressive laser irradiation, the sample reflectance increases and becomes strongly red-sloped.F-S-002:The unirradiated sample exhibits a dark, blue-slopedspectrum. The brightness of the sample increases significantly from <0.2average reflectance over >0.8 reflectance in the most irradiated sampleand thespectral slope also becomesslightly reddened (Fig. 1c). Microstructural and Chemical Analysis: Two primary alteration textures were observed in the samples exposed to simulated space weathering: 1) fluffy C-rich,and 2) vesiculated melt. The fluffy C-rich texture is composed oflow-densitydeposits distributed across the surface of the sample(Fig. 2A). Analysis of a FIB section extracted from a low-density C-rich region in sample SC-001 reveals multiple globule-type deposits, discrete from stacked graphite, likely produced via melting from the laser irradiation [9].The vesiculated melt textureis smooth and uniformly distributed across isolated regions of the sample surface. The vesicles measure up to 100s of nmin diameter. Analysis of a FIB section from this texture was extracted from sample F-T-004 reveals a layer of amorphous melt material, close to 100 nm thick and uniform across the FIB section (Fig. 2B). Isolated regions of this melt layer contain small nanoparticles, <5 nm in diameter. Chemical analysis through energy dispersive X-ray spectroscopy reveals the composition of this layer is enriched in Si and depleted in Mg and O compared to the underlying sample. Implications for Space Weathering on Mercury: Previous experiments simulating space weathering of Mercury have showndarkening and reddening of spectra[7,10].However, our use of low-Fe materials and graphite to create a sample set more analogous to the mercurian surface. Our results indicate that sample composition plays a significant and important role in the space weathering of Mercury. In particular, our spectral data demonstrates a strong correlation between spectral slope, Fe content, and simulated space weathering. While the variation in FeO content between samples F-S-002 and F-T-004 is <0.6 wt.%, the spectra deviate from flat to strongly red-sloped(F-T-004). This reddeningmay be linked to the presence of very small nanoparticles observed in the melt textures extracted from sample F-T-004. For the SC-001 sample, the fluffy C-rich textures may be developed by the amalgamation of small graphite particles into these unique morphologies. Such observations indicate that space weathering on Mercury may result in both familiar and new microstructural and chemical characteristics. References: [1]Hapke B. (2001) J. Geophys. Res.-Planet.,106,10039–10073. [2]Pieters C.M. and Noble S.K. (2016) J. Geophys. Res-Planet., 121, 1865–1884. [3] Lucey P.G., and Riner, M.A. (2011) Icarus,212, 451-462.[4]CintalaM.J.(1992)J. Geophys. Res.-Planet.,97,947–973.[5]Klima R.L.et al.(2018)Geophys.Res.Letters, 45, 2945–2953. [6]Nittler L.R., et al. (2011) Science 333, 1847-1850.[7]Sasaki S. and Kurahashi E. (2004) Space weathering on Mercury, Adv.Space Res., 33, 2152-2155.[8] Vander KaadenK.E., et al. (2018) LPSCXLIX, Abstract 1230. [9] McGlaun M.L. et al. (2019) LPSCL, Abstract 2019. [10] TrangD.et al. (2018)LPSCXLIX,Abstract2083

M S Thompson↗

First-results from the Perseverance SHERLOC Investigation: Aqueous Alteration Processes and Implications for Organic Geochemistry in Jezero Crater, Mars

The Perseverance rover landed in Jezero crater, a site selected to fulfill the Mars-2020 mission goals of characterizing the geology of habitable environments and searching for signs of life while collecting samples for return to Earth [1]. Jezero hosted an open-basin lake during the late Noachian/early Hesperian (~3.7 Ga) [1-2], has units associated with the largest carbonate deposit identified on Mars [3-4], and has a well-preserved delta with clay and carbonate-bearing sediments, well-suited to preservation of organics [1,3-4]. Investigating the nature of organics and aqueous environments within their geologic con-text allows us to understand important aqueous processes and determine habitability within Jezero crater. Previous in situ landed measurements of organics could not resolve their spatial and mineralogical con-text [5-6]. Although Martian meteorites lack geological context, the spatial distribution of organic compounds in Martian meteorites have allowed recognition of an association between aqueous processes and organics [7-8]. Here, we show for the first time in-situ associations between carbonate-forming ultramafic alteration process, later stage aqueous sulfate and perchlorate formation, and organics on the Martian surface. Methodology and geological context: We use the Perseverance rover’s SHERLOC instrument (Scanning Habitable Environments with Raman and Lumines-ence of Organics and Chemicals), a deep-ultraviolet fluorescence and Raman scattering spectrometer capable of mapping the organic and mineral composition with a spatial resolution of 100 μm resolution to report the presence of organics and aqueously formed minerals at Jezero crater [9]. These spectral detections were compared with co-located images obtained with the autofocus context imager (ACI) and the WATSON camera for textural analysis [9]. As of writing, the Per-severance rover has abraded five targets that were measured with the SHERLOC instrument. The five targets are located in two different orbitally-identified geological units within the floor of Jezero crater; the Crater Floor Fractured Rough unit (CF-Fr) and the Séítah region within the Crater Floor Fractured 1 unit (CF-F1) [10]. In orbital infrared spectroscopic data, the CF-Fr unit is associated with pyroxene spectral signatures and minor alteration, while the Séítah region is associated with olivine and minor Mg-rich carbonates and clays [3-4,10]. Carbonation of ultramafic protolith recorded within Jezero crater: All scans of abraded targets within the Séítah region reveal strong peaks at 1080–1090 cm−1 consistent with carbonate and peak singlets or doublets at 820–840 cm−1 attributed to olivine (Fig. 1), consistent with orbital infrared observations. Our detailed micron-scale petrographic and spectroscopic evidence shows that these carbonates formed through carbonation of an ultramafic protolith. The supporting observations include: (1) Carbonate cation compositions match those of olivine, suggesting mixed Fe- and Mg-olivine gave rise to mixed Fe- and Mg-carbonates, similar to observations of ultramafic systems on Earth and within Martian meteorites [3-4,7-8]. (2) The ob-served carbonates co-occur with hydrated materials, gypsum, and potentially aqueously-formed phases, amorphous silicates and phosphate. (3) The spectral and textural variation of olivine and carbonate dominated zones and olivine-carbonate mixtures within both primary grains and interstitial zones are expected for carbonated ultramafic protoliths. (4) These mineral associations and textures closely resemble those observed within the ALH84001 and Nakhlite meteorites attributed to olivine carbonation on Mars [6-7]. Taken together, micron-scale SHERLOC documentation of these phenomena bridge previous orbital and meteorite observations and demonstrate in-situ regionally extensive (~106 km2) ultramafic alteration resulting in geo-logical deposition of carbonates. Furthermore, we observe that olivine carbonation was involved in preserving and possibly synthesizing organics, which makes this environment potentially habitable, as previously suggested in [1,3-4] (Fig. 1). Late-stage aqueous perchlorate and sulfate in Jezero crater: An abrasion target within the CF-Fr unit contains combinations of high intensity 950-955 cm−1 peaks and minor 1090-1095 cm−1 and 1150-1155 cm−1 peaks that are spectral fits to anhydrous perchlorate (Fig. 1). Some spectra show a combination of 950-955 cm−1 peaks with equally strong 1010-1020 cm−1 peaks, low intensity broad features at 1120 cm−1, and occasional broad 3450 cm−1 hydration (-OH) features, indicating a mixture of Ca-sulfate and perchlorate that is minimally hydrated (Fig. 1). The detections of per-chlorates within Jezero crater differ from previous measurements (e.g. Phoenix lander, Curiosity rover, Tissint meteorite [7,11]) because they are observed to be intimately related to aqueous processes including sulfate formation, they present as a secondary white void-fill occurring within the interior of the rock, and they are found to likely be Na-perchlorate. implications for their formation: Three different types of organics embedded within three different lithologies were observed within the abraded targets. Organics associated with low intensity ~340 nm fluorescence were widespread within targets with no apparent association to particular minerals (Fig. 1). Organics associated with ~305 nm and ~275 nm fluorescence correlated with sulfates within the Bellegarde target in the CF-Fr unit, while organics associated with high intensity ~340 nm fluorescence correlated with carbonate, phosphate, and amorphous silicate mixtures within the Garde target in the Séítah region (Fig. 1). Although assignment of fluorescence signatures to specific organic compounds is not conclusive, ~340 nm fluorescence is generally more consistent with 2-ring aromatic organics, ~275 nm fluorescence is more consistent with 1-ring aromatic organics, and ~305 nm fluorescence can be created by either 2- or 1-ring aromatics [12]. These observations indicate that the strongest fluorescence signatures interpreted as organics were found in materials associated with aqueous processes, i.e. sulfate- and carbonate-bearing materials, suggesting both brines and ultramafic carbonation aqueous environments were capable of preserving organics on ancient Mars. In Martian meteorites, simple aromatic organics proposed to have been synthesized through aqueous processes can be found within minerals associated with olivine carbonation and in spatial association with perchlorate and sulfate materials [7-8], similar to SHERLOC observations. Hence, we advance an abiotic aqueous synthesis origin for the organics although we cannot rule out the presence of organics from meteoritic in-fall or putative organic biosignatures. Detailed analyses will be required upon return of these materials to Earth.

E L Scheller↗

Coke Deposition and Smoke Formation in Turbojet Engines

In the early development of jet engines, it was occasionally found that excessive amounts of coke or other carbonaceous deposits were formed in the combustion chamber. Sometimes a considerable amount of smoke was noted in the-exhaust gases. Excessive coke deposits may adversely affect jet-engine performance in several ways. The formation of excessive amounts of coke on or just downstream of a fuel nozzle (figs. 116(a) and (b)) changes the fuel-spray pattern and possibly affects combustor life and performance. Similar effects on performance can result from the deposition of coke on primary-air entry ports (fig. 116(c)). Sea-level or altitude starting may be impaired by the deposition of coke on spark-plug electrodes (fig. 116(b)), deposits either grounding the electrodes completely or causing the spark to occur at positions other than the intended gap. For some time it was thought that large deposits of coke in turbojet combustion chambers (fig. 116(a)) might break away and damage turbine blades; however, experience has indicated that for metal blades this problem is insignificant. (Cermet turbine blades may be damaged by loose coke deposits.) Finally, the deposition of coke may cause high-temperature areas, which promote liner warping and cracking (fig. 116(d)) from excessive temperature gradients and variations in thermal-expansion rates. Smoke in the exhaust gases does not generally impair engine performance but may be undesirable from a tactical or a nuisance standpoint. Appendix B of reference 1 and references 2 to 4 present data obtained from full-scale engines operated on test stands and from flight tests that indicate some effects on performance caused by coke deposits and smoke. Some information about the mechanism of coke formation is given in reference 5 and chapter IX. The data indicate that (1) high-boiling fuel residuals and partly polymerized products may be mixed with a large amount of smoke formed in the gas phase to account for the consistency, structure, and chemical composition of the soft coke in the dome and (2) the hard deposits on the liner are similar to petroleum coke and may result from the liquid-phase thermal cracking of the fuel. During the early development period of jet engines, it was noted that the excessive coke deposits and exhaust smoke were generally obtained when fuel-oil-type fuels were used. Engines using gasoline-type fuels were relatively free from the deposits and smoke. These results indicated that some type of quality control would be needed in fuel specifications. Also noted was the effect of engine operating conditions on coke deposition. It is possible that, even with a clean-burning fuel, an excessive amount of coke could be formed at some operating conditions. In this case, combustor redesign could possibly reduce the coke to a tolerable level. This chapter is a summary of the various coke-deposition and exhaust-smoke problems connected- with the turbojet combustor. Included are (1) the effect of coke deposition on combustor life or durability and performance; (2) the effect of combustor design, operating conditions, inlet variables, and fuel characteristics on coke deposition; (3) elimination of coke deposits; (4) the effect of operating conditions and fuel characteristics on formation of exhaust smoke; and (5) various bench test methods proposed for determining and controlling fuel quality.

Hibbard, R. R.↗

Simulation of the December 1998 Stratospheric Major Warming

Prior to 1991, major warmings (defined by increasing zonal mean temperatures and zonal mean easterly winds from 60degN to the pole at 10 hPa) typically occurred approximately once every two Arctic winters; a major warming in mid-Dec. 1998 was the first since Feb. 1991. The Dec. 1998 warming was also the second earliest on record. The earliest, and the only other major warming on record before the end of Dec. was in early Dec 1987; prior to that, the earliest was in late Dec./early Jan. 1984-85. The 1984-85 and 1987 warmings resulted in the warmest and weakest lower stratospheric polar vortices in the 20 years before 1998-99. Fig. 1 compares temperatures and vortex strength in 1998-99 with those in the previous 20 years, using the US National Center for Environmental Prediction (NCEP) record; 1987-88 and 1984-85 are also highlighted. The Dec. 1998 warming had a more pronounced effect on mid-stratospheric temperatures than the Dec. 1987 warming (Fig. 1a), although smaller than that of warmings later in winter (e.g., 1984-85). 10-hPa temperatures fell well below average again in late Jan. 1999 and remained unusually low until an early final warming began in late Feb. 840 K PV gradients (Fig. 1c) set a record minimum in Jan. 1999, but were near average in Feb before the final warming. The effect of the Dec. 1998 warming on lower stratospheric temperatures was comparable to that of other major warmings; there was a brief period of record-high minimum 46-hPa temperatures in early Jan 1999 (Fig. 1b), and temperatures then fell to near average for a short period in mid-Feb. Lower stratospheric PV gradients were the weakest on record during the 1998-99 winter (Fig. 1d). The evolution of the vortex and minimum temperatures during 1998-99 was remarkably similar to that during 1987-88, the only previous year when a major warming was observed before the end of Dec.

Manney, G. L.↗

Proteomic Retrieval from Nucleic Acid Depleted Space-Flown Human Cells

Compared to experiments utilizing humans in microgravity, cell-based approaches to questions about subsystems of the human system afford multiple advantages, such as crew safety and the ability to achieve statistical significance. To maximize the science return from flight samples, an optimized method was developed to recover protein from samples depleted of nucleic acid. This technique allows multiple analyses on a single cellular sample and when applied to future cellular investigations could accelerate solutions to significant biomedical barriers to human space exploration. Cell cultures grown in American Fluoroseal bags were treated with an RNA stabilizing agent (RNAlater - Ambion), which enabled both RNA and immunoreactive protein analyses. RNA was purified using an RNAqueous(registered TradeMark) kit (Ambion) and the remaining RNA free supernatant was precipitated with 5% trichloroacetic acid. The precipitate was dissolved in SDS running buffer and tested for protein content using a bicinchoninic acid assay (1) (Sigma). Equal loads of protein were placed on SDS-PAGE gels and either stained with CyproOrange (Amersham) or transferred using Western Blotting techniques (2,3,4). Protein recovered from RNAlater-treated cells and stained with protein stain, was measured using Imagequant volume measurements for rectangles of equal size. BSA treated in this way gave quantitative data over the protein range used (Fig 1). Human renal cortical epithelial (HRCE) cells (5,6,7) grown onboard the International Space Station (ISS) during Increment 3 and in ground control cultures exhibited similar immunoreactivity profiles for antibodies to the Vitamin D receptor (VDR) (Fig 2), the beta isoform of protein kinase C (PKC ) (Fig 3), and glyceraldehyde-3-phosphate dehydrogenase (GAPDH) (Fig 4). Parallel immunohistochemical studies on formalin-fixed flight and ground control cultures also showed positive immunostaining for VDR and other biomarkers (Fig 5). These results are consistent with data from additional antigenic recovery experiments performed on human Mullerian tumor cells cultured in microgravity (8).

Hammond, D. K.↗

Failure Analysis of T-38 Aircraft Burst Hydraulic Aileron Return Line

During maintenance troubleshooting for fluctuating hydraulic pressures, a technician found that a right hand aileron return line, on the flight hydraulic side, was ruptured (Fig. 1, 2). This tubing is part of the Hydraulic Flight Control Aileron Return Reducer to Aileron Manifold and is suspected to be original to the T-38 Talon trainer aircraft. Ailerons are small hinged sections on the outboard portion of a wing used to generate rolling motion thereby banking the aircraft. The ailerons work by changing the effective shape of the airfoil of the outer portion of the wing [1]. The drawing, Northrop P/N 3-43033-55 (6/1960), specifies that the line is made from 0.375 inch OD, aluminum 5052-0 tubing with a 0.049 inch wall thickness. WW-T-787 requires the tube shall be seamless and uniform in quality and temper [2]. The test pressure for this line is 3000 psi, and the operational pressure for this line is estimated to be between 45 psi and 1500 psi based on dynamic loading during flight. Examination of the fracture surface found evidence of arrest bands originating on the inner diameter (Fig 3). Ductile dimples are observed on the tube fractures (Fig. 4). The etched cross-section revealed thinning and work-hardening in the burst region (Fig. 5). The wall thickness just outside the work-hardened fracture region measured 0.035". Barlow's Formula: P = 2St/D, where P is burst pressure, S is allowable stress, t is wall thickness and D is the outer diameter of tube. Using the ultimate tensile strength of 28 ksi and a measured wall thickness of 0.035 inches at burst, P = 5.2 ksi (burst pressure). Using the yield of 13 ksi (YS) for aluminum 5052-0, plastic deformation will happen at P = 2.4 ksi suggesting plastic deformation occurred at a proof pressure of 3.0 ksi. Conclusion: The burst resulted from high stress, low-cycle fatigue. Evidence of arrest bands originating on the inner diameter. Fracture is predominately shear dimples, characteristic of high load ductile fractures (Fig 6). Section wall reduction in the burst region. Plastic deformation and thinning of the out-of-specification tube wall likely happened during the initial proof testing years ago. Metallography of tubing away from rupture site confirmed tubing was seamless. Based on the tube microstructure, it is likely that the initial wall thickness was about 30 % thinner than the requirement of 0.049 inches. Fracture initiated on the ID and progressed to the OD (shear lip). The tube is made of the correct material of 5052-0 aluminum as verified using Optical Emission Spectroscopy (Table 2). The tubing hardness tested 77 HV100 (77 HRE). This hardness is slightly above the requirement for 70 HRE maximum for aluminum 5052-0 in AMS 2658C [3].

Martinez, J. E.↗

Effect of Inflow Boundary Conditions on Hovering Tilt-Rotor Flows

A study on the effect of inflow turbulence boundary conditions on the local flow on and around a body in flight has been carried out. The study has been carried out using OVERFLOW2 flow solver using the default Spalart-Allmaras turbulence model in OVERFLOW. Many OVERFLOW turbulent flow simulations have been reported using the SA-fv3 model1 over the years. The present study demonstrates that the turbulence levels imposed as a boundary condition (b.c.) in the far-field as implemented in OVERFLOW are not correct. In fact, very low level of turbulence at the far-field boundary as implemented in OVERFLOW results in the SA-fv3 model predicting transition-like profiles on a given body. By choosing sufficiently high levels of the Reynolds number of turbulence, Rt, as a boundary condition, this anomalous behavior of SA-fv3 model is eliminated. Since numerous papers using OVERFLOW have been presented in the literature including that by the author2 using low level of inflow turbulence, it will be beneficial to the CFD community at large and in particular to the OVERFLOW community to understand this effect of the inflow b.c. in the SA-fv3 model. Various results reported over the years in domains such as high-lift applications, drag prediction applications and rotorcraft flow applications can be revisited using the new turbulence inflow boundary condition prescription as suggested in this study. It has been demonstrated in the literature that the effect of inflow turbulence level on the downstream development of flow is too important to be ignored. Demonstrative results are shown and compared with experiment for the case of hovering XV-15 rotor flow at a tip Reynolds number of 4.9 x 10(exp 6) and Mach number of 0.69 in Figs. 1 and 2 below. Fig. 1(a,b) shows skin friction predictions at radial station of r/R = 0.28 corresponding to 5 different inflow boundary conditions obtained with the SA-fv3 model. As the inflow turbulence is increased monotonically, from a value of Rt = 0.1 to 100.0 as shown in Fig. 1, a fully developed turbulent skin friction profile is realized progressively as shown in Fig. 1(b). Similarly skin friction results shown in Fig. 2(a,b) corresponding to radial stations of r/R = 0.72 reinforce the postulate made here that as the inflow turbulence level is increased gradually, fully turbulent on-the-blade simulation is realized uniformly. In the full paper extensive results on skin friction, pressure and velocity profiles as well as the Figure of Merit will be presented and compared with experiment that will illustrate the substantial effect of the inflow boundary conditions on the development of hovering rotor flow downstream.

Kaul, Upender K.↗

Acoustics Reflections of Full-Scale Rotor Noise Measurements in NFAC 40- by 80-Foot Wind Tunnel

The objective of current research is to identify the extent of acoustic time history distortions due to wind tunnel wall reflections. Acoustic measurements from the recent full-scale Boeing-SMART rotor test (Fig. 2) will be used to illustrate the quality of noise measurement in the NFAC 40- by 80-Foot Wind Tunnel test section. Results will be compared to PSU-WOPWOP predictions obtained with and without adjustments due to sound reflections off wind tunnel walls. Present research assumes a rectangular enclosure as shown in Fig. 3a. The Method of Mirror Images7 is used to account for reflection sources and their acoustic paths by introducing mirror images of the rotor (i.e. acoustic source), at each and every wall surface, to enforce a no-flow boundary condition at the position of the physical walls (Fig. 3b). While conventional approach evaluates the "combined" noise from both the source and image rotor at a single microphone position, an alternative approach is used to simplify implementation of PSU-WOPWOP for this reflection analysis. Here, an "equivalent" microphone position is defined with respect to the source rotor for each mirror image that effectively renders the reflection analysis to be a one rotor, multiple microphones problem. This alternative approach has the advantage of allowing each individual "equivalent" microphone, representing the reflection pulse from the associated wall surface, to be adjusted by the panel absorption coefficient illustrated in Fig. 1a. Note that the presence of parallel wall surfaces requires an infinite number of mirror images (Fig. 3c) to satisfy the no-flow boundary conditions. In the present analysis, up to four mirror images (per wall surface) are accounted to achieve convergence in the predicted time histories

Barbely, Natasha Lydia↗