Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FAPbI3”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

14 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Amine-Assisted Ligand-Exchange Method to Enhance Photovoltaic Parameters in FAPbI3 Nanocrystal Solar Cells

Perovskite colloidal nanocrystals (PeNCs) have exceptional optoelectronic properties and phase stability, making them promising for photovoltaic applications. However, insulating ligands on PeNC surfaces limit the current density and reduce the power conversion efficiency (PCE) in PeNC solar cells (SCs). This study introduces an amine-assisted ligand-exchange (ALE) strategy using 3-phenyl-1-propylamine (3P1P) to effectively remove long ligands from PeNC films. ALE reduced long-chain ligand density without increasing the number of defect states and therefore reduced the exciton-binding energy of FAPbI3 NC films. These changes facilitated exciton dissociation and charge transport in FAPbI3 PeNC SCs. The facilitation of exciton dissociation was due to the increased magnetic dipole interaction between excitons after the ALE process. The use of ALE achieved FAPbI3 PeNC SCs that had an improved short-circuit current density of 17.98 mA/cm2 and a PCE of 15.56% with improved stability after the treatment and negligible hysteresis. This work provides new insight into engineering PeNC films.

amines↗
DOE OSTI2023

Photo-excited charge carrier lifetime enhanced by slow cation molecular dynamics in lead iodide perovskite FAPbI3

Using muon spin relaxation measurements on formamidinium lead iodide [FAPbI3, where FA denotes HC(NH2)2], we show that, among the five structurally distinct phases of FAPbI3 exhibited through two different temperature hysteresis, the reorientation motion of FA molecules is quasi-static below ≈50 K over the time scale of 10−6 s in the low-temperature (LT) hexagonal (Hex-LT, <160 K) phase, which has a relatively longer photo-excited charge carrier lifetime (τc∼10−6 s). In contrast, a sharp increase in the FA molecular motion was found above ≈50 K in the Hex-LT phase, LT-tetragonal phase (Tet-LT, <140 K), the high-temperature (HT) hexagonal phase (Hex-HT, 160–380 K), and the HT-tetragonal phase (Tet-HT, 140–280 K), where τc decreases with increasing temperature. More interestingly, the reorientation motion is further promoted in the cubic phase at higher temperatures (>380/280 K), while τc is recovered to comparable or larger than that of the LT phases. These results indicate that there are two factors that determine τc, one related to the local reorientation of cationic molecules that is not unencumbered by phonons and the other to the high symmetry of the bulk crystal structure.

Physics↗
DOE OSTI2021

Impact of Humidity and Temperature on the Stability of the Optical Properties and Structure of MAPbI3, MA0.7FA0.3PbI3 and (FAPbI3)0.95(MAPbBr3)0.05 Perovskite Thin Films

In situ real-time spectroscopic ellipsometry (RTSE) measurements have been conducted on MAPbI3, MA0.7FA0.3PbI3, and (FAPbI3)0.95(MAPbBr3)0.05 perovskite thin films when exposed to different levels of relative humidity at given temperatures over time. Analysis of RTSE measurements track changes in the complex dielectric function spectra and structure, which indicate variations in stability influenced by the underlying material, preparation method, and perovskite composition. MAPbI3 and MA0.7FA0.3PbI3 films deposited on commercial fluorine-doped tin oxide coated glass are more stable than corresponding films deposited on soda lime glass directly. (FAPbI3)0.95(MAPbBr3)0.05 films on soda lime glass showed improved stability over the other compositions regardless of the substrate, and this is attributed to the preparation method as well as the final composition.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Polaron and Spin Dynamics in Organic–Inorganic Lead Halide Perovskite Nanocrystals

Long-lived carrier population and spin-based behavior in lead halide perovskite nanocrystals (NCs) are very interesting for implementing photovoltaic devices with efficiencies exceeding the Shockley–Queisser limit and quantum information processing, respectively. However, a comprehensive understanding of polaron-mediated charge carrier interactions and an accurate description of the spin-polarized states for spintronics are still lacking. Herein, the carrier and spin interactions are studied under controlled conditions in FAPbI 3 and Cs 0.01 FA 0.99 Pb(Br 0.11 I 0.89 ) 3 NCs through ultrafast transient absorption (TA) spectroscopy. At early timescales, TA spectrum shows an asymmetric derivative feature originating from the hot carrier-induced spectral redshift in FAPbI 3 NCs (55 ± 3 meV) and Cs0.01FA0.99Pb(Br0.11I0.89)3 NCs (54 ± 2 meV) at the bandedges that stabilizes to 9 ± 1 and 11 ± 2 meV, respectively, at 1 ps due to the polaron formation. The kinetic analysis indicates that the polaron populations in FAPbI3 and Cs 0.01 FA 0.99 Pb(Br 0.11 I 0.89 ) 3 NCs decay with an average lifetime of 657 ± 34 and 532 ± 28 ps, respectively. The circular polarization-resolved TA reveals that polaron formation can control spin relaxation in NCs, thus providing a powerful tool to explore the development of their prospective applications in spintronics.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Exploring Transport Behavior in Hybrid Perovskites Solar Cells via Machine Learning Analysis of Environmental-Dependent Impedance Spectroscopy

Hybrid organic–inorganic perovskites are one of the promising candidates for the next-generation semiconductors due to their superlative optoelectronic properties. However, one of the limiting factors for potential applications is their chemical and structural instability in different environments. Herein, the stability of (FAPbI3)0.85(MAPbBr3)0.15 perovskite solar cell is explored in different atmospheres using impedance spectroscopy. An equivalent circuit model and distribution of relaxation times (DRTs) are used to effectively analyze impedance spectra. DRT is further analyzed via machine learning workflow based on the non-negative matrix factorization of reconstructed relaxation time spectra. This exploration provides the interplay of charge transport dynamics and recombination processes under environment stimuli and illumination. The results reveal that in the dark, oxygen atmosphere induces an increased hole concentration with less ionic character while ionic motion is dominant under ambient air. Under 1 Sun illumination, the environment-dependent impedance responses show a more striking effect compared with dark conditions. In this case, the increased transport resistance observed under oxygen atmosphere in equivalent circuit analysis arises due to interruption of photogenerated hole carriers. The results not only shed light on elucidating transport mechanisms of perovskite solar cells in different environments but also offer an effective interpretation of impedance responses.

36 MATERIALS SCIENCE↗
DOE OSTI2023

The Role of SnO2 Processing on Ionic Distribution in Double-Cation-Double Halide Perovskites

Moving toward a future of efficient, accessible, and less carbon-reliant energy devices has been at the forefront of energy research innovations for the past 30 years. Metal-halide perovskite (MHP) thin films have gained significant attention due to their flexibility of device applications and tunable capabilities for improving power conversion efficiency. Serving as a gateway to optimize device performance, consideration must be given to chemical synthesis processing techniques. Therefore, how does common substrate processing techniques influence the behavior of MHP phenomena such as ion migration and strain? Here, we demonstrate how a hybrid approach of chemical bath deposition (CBD) and nanoparticle SnO2 substrate processing significantly improves the performance of (FAPbI3)0.97(MAPbBr3)0.03 by reducing micro-strain in the SnO2 lattice, allowing distribution of K+ from K-Cl treatment of substrates to passivate defects formed at the interface and produce higher current in light and dark environments. X-ray diffraction reveals differences in lattice strain behavior with respect to SnO2 substrate processing methods. Through use of conductive atomic force microscopy (c-AFM), conductivity is measured spatially with MHP morphology, showing higher generation of current in both light and dark conditions for films with hybrid processing. Additionally, time-of-flight secondary ionization mass spectrometry (ToF-SIMS) observed the distribution of K+ at the perovskite/SnO2 interface, indicating K+ passivation of defects to improve the power conversion efficiency (PCE) and device stability. We show how understanding the role of ion distribution at the SnO2 and perovskite interface can help reduce the creating of defects and promote a more efficient MHP device.

conductive atomic force microscopy↗
DOE OSTI2021

Hot Carrier Redistribution, Electron-Phonon Interaction, and Their Role in Carrier Relaxation in Thin Film Metal-Halide Perovskites

Temperature dependent (4–295 K) photoluminescence and transmission spectra are analyzed to study the effect of changing the different components of a perovskite compound, be it A, B, or X. Four different films are compared: FAMAPbSnI3, FAPbI3, FAMAPbI3, and FAPbBr3. The low temperature results highlight the changes that occur, especially underlying ones that are easily masked at room temperature. The overall Stokes shift is of similar magnitude at room temperature for the three Pb only based samples. This is governed by the interaction strength GLO, phonon energy ELO, and exciton binding energy Eex. One exception to this behavior is the Sn based FAMAPbSnI3 film, which shows a lack of Stokes shift between the absorption and photoluminescence. However, the strong absorption (more than 100 meV) below the band gap is indicative of an excitonic feature that has a large density of states. Transient absorption measurements confirm the trends observed in continuous wave (CW) measurements; the three Pb only films all show the convolution of an excitonic feature within 20 meV of the band gap as a contributing factor to the photobleach along with a region of high energy photoinduced absorption (PIA). However, the behavior for the Sn based film is notably different (just as it is in the CW measurements) with an unusual low energy PIA and a lack of high energy PIA. The large unusual low energy PIA is attributed to the large sub-band-gap absorption observed in the CW transmission/absorption measurements. Notably, regardless of interchanging components, the slow cooling of carriers in metal-halide perovskites shows little effect of GLO, ELO, and Eex. As such, here it is proposed that while the initial cooling of carriers is attributed to LO phonons, the overall cooling of carriers is dominated by the intrinsic low thermal conductivity of all metal-halide perovskites, which limits the dissipation of acoustic phonons in these systems

2D perovskites↗
DOE OSTI2022

Development and Prospects of Halide Perovskite Single Crystal Films

Halide perovskite single crystal (HPSC) films have demonstrated extraordinary performance in solar cells, photodetectors, and lighting applications, owing to the high carrier mobility, long carrier diffusion length, tunable bandgap, and large light absorption coefficients of these materials. Here, the recent development of the major HPSC thin films is reviewed systematically, including MAPbI 3 , α-FAPbI 3 , MAPbBr 3 , CsPbBr 3 , with special emphasis on different classes of fabrication methods and thin-film characteristics. So finally, the conclusion and prospects in this field are discussed in detail. It is anticipated that the HPSC thin films will lead to a compelling future for the rising electronic applications.

MAPbI3↗
DOE OSTI2021

Combined Precursor Engineering and Grain Anchoring Leading to MA-Free, Phase-Pure, and Stable α-Formamidinium Lead Iodide Perovskites for Efficient Solar Cells

a-Formamidinium lead iodide (a-FAPbI 3 ) is one of the most promising candidate materials for high-efficiency and thermally stable perovskite solar cells (PSCs) owing to its outstanding optoelectrical properties and high thermal stability. However, achieving a stable form of a-FAPbI 3 where both the composition and the phase are pure is very challenging. In this work, we report on a combined strategy of precursor engineering and grain anchoring to successfully prepare methylammonium (MA)-free and phase-pure stable a-FAPbI 3 films. The incorporation of volatile FA-based additives in the precursor solutions completely suppresses the formation of non-perovskite d-FAPbI 3 during film crystallization. Grains of the desired a-phase are anchored together and stabilized when 4-tert-butylbenzylammonium iodide is permeated into the a-FAPbI 3 film interior via grain boundaries. This cooperative scheme leads to a significantly increased efficiency close to 21% for FAPbI 3 perovskite solar cells. Moreover, the stabilized PSCs exhibit improved thermal stability and maintained ~90 % of their initial efficiency after storage at 50 degrees C for over 1600 hours.

14 SOLAR ENERGY↗
DOE OSTI2025

Low-dimensional carbon materials decorated FAPbI 3 for carbon-based perovskite solar cells

Carbon nanomaterials are at the forefront of research in perovskite solar cells (PSCs) due to their exceptional electrical, optical, and stability properties. Their diverse applications include serving as interfacial layers, additives, hole and electron transport materials, and back electrodes. While the influence of various low-dimensional carbon nanomaterial structures on crystallinity, optical and electrical performance, and overall device efficiency has been a topic of interest, it has not been thoroughly explored until now. In this study, we effectively integrated carbon quantum dots (CQDs), multi-walled carbon nanotubes (MWCNTs), and graphene into the FAPbI 3 photoactive layer using a two-step sequential deposition method. Our experiments revealed marked improvements in the photovoltaic performance of PSCs that incorporated all three types of carbon nanomaterials. In particular, the data shows significant enhancements in power conversion efficiency, demonstrating the effectiveness of these materials in optimizing device functionality. Notably, MWCNTs distinguished themselves by exhibiting a remarkable potential for enhancing long-term stability. This finding underscores the importance of selecting the right carbon nanomaterials for future PSC developments, paving the way for more reliable and efficient solar energy solutions. As a result, our research highlights the critical role of carbon nanomaterials in advancing perovskite solar technology.

14 SOLAR ENERGY↗
DOE OSTI2024

Supramolecular design principles in pseudohalides for high-performance perovskite solar mini modules

In this work, we reveal the role of non-covalent interactions, which are known to play important roles in supramolecular phenomena, in achieving efficient perovskite surface and grain boundary passivation. By using a series of pseudohalides, we find that trifluoroacetate (TFA - ) provides the strongest binding to iodide vacancies by means of non-covalent hydrogen bonding and dispersion interactions. By exploiting additional non-covalent dispersion and hydrophobic interactions in aromatic 3,3-diphenylpropylammonium (DPA + ), we present a dual-ion passivation strategy that not only minimizes the non-radiative recombination center and local chemical inhomogeneities but also induces preferentially oriented growth of α-FAPbI 3 lattice. Further, this leads to an outstanding power conversion efficiency (PCE) of 25.63% with an exceptional open-circuit voltage of 1.191 V in a perovskite solar cell with a small area, while perovskite solar mini modules with aperture areas of 25 and 64cm 2 achieved PCE of 22.47% (quasi-steady-state [QSS]-certified 20.50%) and 20.88%, respectively, with outstanding stability under high-humidity conditions.

14 SOLAR ENERGY↗
DOE OSTI2021

Phase transition dynamics in one-dimensional halide perovskite crystals

Triiodide perovskites CsPbI 3 , CsSnI 3 , and FAPbI 3 (where FA is formamidinium) are highly promising materials for a range of optoelectronic applications in energy conversion. However, they are thermodynamically unstable at room temperature, preferring to form low-temperature (low-T) non-perovskite phases with one-dimensional anisotropic crystal structures. While such thermodynamic behavior represents a major obstacle toward realizing high-performance devices based on their high-temperature (high-T) perovskite phases, the underlying phase transition dynamics are still not well understood. Here we use in situ optical micro-spectroscopy to quantitatively study the transition from the low-T to high-T phases in individual CsSnI 3 and FAPbI 3 nanowires. We reveal a large blueshift in the photoluminescence (PL) peak (~38 meV) at the low-T/high-T two-phase interface of partially transitioned FAPbI 3 wire, which may result from the lattice distortion at the phase boundary. Compared to the experimentally derived activation energy of CsSnI 3 (~1.93 eV), the activation energy of FAPbI 3 is relatively small (~0.84 eV), indicating a lower kinetic energy barrier when transitioning from a face-sharing octahedral configuration to a corner-sharing one. Further, the phase propagation rate in CsSnI 3 is observed to be relatively high, which may be attributed to a high concentration of Sn vacancies. Furthermore, our results could not only facilitate a deeper understanding of phase transition dynamics in halide perovskites with anisotropic crystal structures, but also enable controllable manipulation of optoelectronic properties via local phase engineering.

36 MATERIALS SCIENCE↗