Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Energy grids and networks”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Status of wind-energy conversion

The utilization of wind energy is technically feasible as evidenced by the many past demonstrations of wind generators. The cost of energy from the wind has been high compared to fossil fuel systems; a sustained development effort is needed to obtain economical systems. The variability of the wind makes it an unreliable source on a short term basis. However, the effects of this variability can be reduced by storage systems or connecting wind generators to: (1) fossil fuel systems; (2) hydroelectric systems; or (3) dispersing them throughout a large grid network. Wind energy appears to have the potential to meet a significant amount of our energy needs.

Thomas, R. L.↗
NASA NTRS1973

Status of wind-energy conversion

The utilization of wind energy is technically feasible as evidenced by the many past demonstrations of wind generators. The cost of energy from the wind has been high compared to fossil fuel systems. A sustained development effort is needed to obtain economical systems. The variability of the wind makes it an unreliable source on a short-term basis. However, the effects of this variability can be reduced by storage systems or connecting wind generators to fossil fuel systems, hydroelectric systems, or dispersing them throughout a large grid network. The NSF and NASA-Lewis Research Center have sponsored programs for the utilization of wind energy.

Thomas, R. L.↗
NASA NTRS1986

A micrometeoroid deceleration and capture experiment: Conceptual experiment design description

The preliminary conceptual design for a cosmic dust collector is described. For the case of low Earth orbit (LEO), dust particles enter the collector through the collimator at a few volts negative potential due to charging in the ionosphere, at a velocity of 1 to 50 km/sec. The particles then pass through an electron stream and are charged to about 1 KV negative (regardless of incoming polarity). The 1 KV negatively charged particle then passes through three sensing grids coupled to charge sensitive preamps (CSP). The comparison of the two pulses provided by S(1) and S(2) are utilized by the microprocessor to determine the charge, q, on the particle (pulse amplitude) and its velocity, v (by time of flight). The third sensing grid, S(3), is kept at about 20 KV negative so that the dust particle will now be decelerated in passing from S(2) (zero potential) to S(3). S(3) is capacitively coupled to its CSP and the pulse from S(3) is utilized by the microprocessor to determine the particle's energy, E, and therefore its mass, m (again by time of flight) by comparison with the pulses from S(1) and S(2). The microprocessor can now precisely program the high-voltage switching network for the proper timing in the grounding of the successive deceleration grids. As determined by the microprocessor, each successive deceleration grid is grounded just after the dust particle passes, thus reducing the particle's energy by the amount q*100 KV at each stage. The microprocessor also determines at which stage the particle will fall below a certain critical energy where all remaining grids remain unswitched so that the particle will drift to the collector. The collector is kept at about 100V positive and is covered with gold foil to eliminate contamination and is removable for subsequent return to earth for detailed analysis.

Wolfe, J. H.↗
NASA NTRS1996

Immobile Robots: AI in the New Millennium

A new generation of sensor rich, massively distributed, autonomous systems are being developed that have the potential for profound social, environmental, and economic change. These include networked building energy systems, autonomous space probes, chemical plant control systems, satellite constellations for remote ecosystem monitoring, power grids, biosphere-like life support systems, and reconfigurable traffic systems, to highlight but a few. To achieve high performance, these immobile robots (or immobots) will need to develop sophisticated regulatory and immune systems that accurately and robustly control their complex internal functions. To accomplish this, immobots will exploit a vast nervous system of sensors to model themselves and their environment on a grand scale. They will use these models to dramatically reconfigure themselves in order to survive decades of autonomous operations. Achieving these large scale modeling and configuration tasks will require a tight coupling between the higher level coordination function provided by symbolic reasoning, and the lower level autonomic processes of adaptive estimation and control. To be economically viable they will need to be programmable purely through high level compositional models. Self modeling and self configuration, coordinating autonomic functions through symbolic reasoning, and compositional, model-based programming are the three key elements of a model-based autonomous systems architecture that is taking us into the New Millennium.

Williams, Brian C.↗
NASA NTRS1994

Evaluating GCM land surface hydrology parameterizations by computing river discharges using a runoff routing model: Application to the Mississippi basin

To relate general circulation model (GCM) hydrologic output to readily available river hydrographic data, a runoff routing scheme that routes gridded runoffs through regional- or continental-scale river drainage basins is developed. By following the basin overland flow paths, the routing model generates river discharge hydrographs that can be compared to observed river discharges, thus allowing an analysis of the GCM representation of monthly, seasonal, and annual water balances over large regions. The runoff routing model consists of two linear reservoirs, a surface reservoir and a groundwater reservoir, which store and transport water. The water transport mechanisms operating within these two reservoirs are differentiated by their time scales; the groundwater reservoir transports water much more slowly than the surface reservior. The groundwater reservior feeds the corresponding surface store, and the surface stores are connected via the river network. The routing model is implemented over the Global Energy and Water Cycle Experiment (GEWEX) Continental-Scale International Project Mississippi River basin on a rectangular grid of 2 deg X 2.5 deg. Two land surface hydrology parameterizations provide the gridded runoff data required to run the runoff routing scheme: the variable infiltration capacity model, and the soil moisture component of the simple biosphere model. These parameterizations are driven with 4 deg X 5 deg gridded climatological potential evapotranspiration and 1979 First Global Atmospheric Research Program (GARP) Global Experiment precipitation. These investigations have quantified the importance of physically realistic soil moisture holding capacities, evaporation parameters, and runoff mechanisms in land surface hydrology formulations.

Liston, G. E.↗
NASA NTRSDate not supplied

A Neural Network Parametrization of Volumetric Cloud Fraction Profiles Using Satellite Observations and MERRA-2 Reanalysis Meteorological Data

Clouds play a crucial role in regulating the hydrologic cycle and Earth's radiative energy budget, yet they are often poorly represented in global climate models (GCMs). This study applies deep machine learning techniques to develop a physical parameterization of volumetric cloud fraction (VCF), the fraction of a 3-D grid volume occupied by clouds using satellite lidar-radar measurements. The neural network (NN) captures the complicated relationships between observed VCF profiles and collocated meteorological variables from MERRA-2 reanalysis data. Our results show that the NN model, particularly a sequence-to-sequence long short-term memory (LSTM) network with a sixfactor loss function, effectively learns the underlying cloud physical processes. The NN model outperforms MERRA-2 reanalysis in representing low-level clouds in tropical and subtropical regions and low- and middle-level clouds over midlatitude storm-track regions, and also improves VCF histograms. These improvements are reflected in the vertical distributions of zonally, meridionally, and globally averaged VCFs, geographic distributions of low-, middle-, and high-level clouds, and seasonal variations in monthly-mean VCF. Furthermore, the NN predictions effectively capture the El Niño-Southern Oscillation (ENSO) effects and other interannual variations. The NN parameterization is further evaluated through a sensitivity analysis, in which a single predictor is perturbed at a time. This reveals that relative humidity (RH) is the dominant factor influencing variations in globally averaged VCF at low and middle altitudes, followed by temperature. At higher altitudes, temperature becomes the primary driver of VCF through its effect on RH. Changes in wind components had minimal impact on globally averaged VCF.

Shan Zeng↗
NASA NTRS2010

Effects of Lightning and Other Meteorological Factors on Fire Activity in the North American Boreal Forest: Implications for Fire Weather Forecasting

The effects of lightning and other meteorological factors on wildfire activity in the North American boreal forest are statistically analyzed during the fire seasons of 2000-2006 through an integration of the following data sets: the MODerate Resolution Imaging Spectroradiometer (MODIS) level 2 fire products, the 3-hourly 32-kin gridded meteorological data from North American Regional Reanalysis (NARR), and the lightning data collected by the Canadian Lightning Detection Network (CLDN) and the Alaska Lightning Detection Network (ALDN). Positive anomalies of the 500 hPa geopotential height field, convective available potential energy (CAPE), number of cloud-to-ground lightning strikes, and the number of consecutive dry days are found to be statistically important to the seasonal variation of MODIS fire counts in a large portion of Canada and the entirety of Alaska. Analysis of fire occurrence patterns in the eastern and western boreal forest regions shows that dry (in the absence of precipitation) lightning strikes account for only 20% of the total lightning strikes, but are associated with (and likely cause) 40% of the MODIS observed fire counts in these regions. The chance for ignition increases when a threshold of at least 10 dry strikes per NARR grid box and at least 10 consecutive dry days is reached. Due to the orientation of the large-scale pattern, complex differences in fire and lightning occurrence and variability were also found between the eastern and western sub-regions. Locations with a high percentage of dry strikes commonly experience an increased number of fire counts, but the mean number of fire counts per dry strike is more than 50% higher in western boreal forest sub-region, suggesting a geographic and possible topographic influence. While wet lightning events are found to occur with a large range of CAPE values, a high probability for dry lightning occurs only when 500 hPa geopotential heights are above 5700m and CAPE values are near the maximum observed level, underscoring the importance of low-level instability to boreal fire weather forecasts-

Peterson, D.↗
NASA NTRS2021

Improving the CERES SYN Cloud and Flux Products by Identifying GOES-17 Scan Anomalies Using a Convolutional Neural Network

The NASA Clouds and the Earth’s Radiant Energy System (CERES) project relies on top-of-atmosphere (TOA) broadband fluxes derived from geostationary (GEO) satellite imagery to account for the diurnal flux variations between the CERES observation intervals, and thereby produce a synoptic gridded (SYN1deg) product based on continuous temporal observations. Consistent broadband flux derivation depends on accurate radiative property measurements and cloud retrievals, which largely determine the radiance-to-flux conversion process. Therefore, it is important to ensure a high quality of cloud property input in order to maintain a reliable broadband flux record. In Edition 4 of the CERES SYN1deg product, a robust automated image anomaly detection algorithm based on inter-line and inter-pixel differences, spatial variance, and 2-D Fourier analysis has been successful in identifying imagery with linear artifacts, but the line-by-line inspection and cleaning process must still be performed by a human. Therefore, further automation of this quality assurance process is warranted, especially considering the excessive amount of additional cleaning necessitated by the GOES-17 Advance Baseline Imager (ABI) cooling system anomaly. As such, this article highlights advancement of the CERES GEO image artifact cleaning approach based on a convolutional neural network (CNN) for classification of bad scanlines. Once trained, the CNN approach is a computationally inexpensive means to ensure greater consistency in cloud retrievals, and therefore broadband flux derivation, based on GOES-17 measurements.

Benjamin Scarino↗
NASA NTRS1993

Application of multigrid methods to the solution of liquid crystal equations on a SIMD computer

We will describe a finite difference code for computing the equilibrium configurations of the order-parameter tensor field for nematic liquid crystals in rectangular regions by minimization of the Landau-de Gennes Free Energy functional. The implementation of the free energy functional described here includes magnetic fields, quadratic gradient terms, and scalar bulk terms through the fourth order. Boundary conditions include the effects of strong surface anchoring. The target architectures for our implementation are SIMD machines, with interconnection networks which can be configured as 2 or 3 dimensional grids, such as the Wavetracer DTC. We also discuss the relative efficiency of a number of iterative methods for the solution of the linear systems arising from this discretization on such architectures.

Farrell, Paul A.↗
NASA NTRS1992

Semi-coupled flow and thermal analysis of the field joint during rapid pressurization of the redesigned solid rocket motor

A transient, semi-coupled, multi-dimensional thermal and flow analysis methodology was developed to predict the thermal/gas dynamic conditions in the field joint region of the Redesigned Solid Rocket Motor (RSRM). Transient temperature response, pressure history, and combustion gas flow rate (within the field joint region), were of principle interest, in the course of this study. The thermal environment in the field joint was modeled using SINDA, a finite difference based thermal network analyzer. The combustion gas flow boundary condition was generated using the FLAP code; this code performs a transient, lumped-parameter, control volume analysis to solve the mass, momentum, and energy conservation equations. The FLAP computer code was modified to account for erosion of the NBR insulation material, following ignition. An independent grid sensitivity study was conducted to determine an appropriate grid distribution near the wall. The predicted results, obtained using an optimum grid distribution and computer generated flow boundary condition, were compared with subscale test data.

Ghaffarian, Benny↗
NASA NTRSDate not supplied

TPSAS-NF1676L-17940-DND

The NASA/GEWEX SRB (Global Energy and Water Exchanges, Surface Radiation Budget) project produces and archives shortwave and longwave radiation budget flux estimates at the top of the atmosphere and at the Earth's surface. The latest version in the archive, Release 3.0, is available as 3-hourly, 3-hourly-monthly, daily and monthly means continuously over the period from July 1983 to December 2007 on a quasi-equal-area grid system of 44016 grid boxes. SRB Release 4 with further improvements in data quality and higher spatial resolution is being developed. The SRB shortwave/longwave fluxes at the Earth's surface from the algorithm GSW(V3.0)/GLW(V3.1) have been extensively validated against high-quality ground-based observations, in particular observed data from the Baseline Surface Radiation Network (BSRN). Comparisons with nearly 6000 site-months of both shortwave and longwave data from 52 BSRN sites show generally good agreement. In addition, the GEWEX SRB data have also been found to compare favorably with the World Radiation Data Centre (WRDC) data and the Global Energy Balance Archive (GEBA) data. In spite of the fact that the BSRN sites are scattered on all seven continents, the validation of the SRB data over the vast oceans had not been done until recently. In this paper, we present comparisons of the GEWEX-SRB data shortwave/longwave data with observations made on arrays moored in tropical oceans. Specifically, we have data from 21 buoys, or moorings, from Predictions and Research Moored Array in the Atlantic (PIRATA), 14 buoys from the Research Moored Array for African-Asian-Australian Monsoon Analysis and Prediction (RAMA) in the Indian Ocean, 20 buoys from the Tropical Atmosphere Ocean (TAO) array in the Pacific, and 3 buoys from the Woods Hole Oceanographic Institute (WHOI) (2 in the Pacific and 1 in the Atlantic). The data from these buoys span 12 years from 2000 to 2011, though not necessarily continuously. It is found that except for occasional outliers, the majority of the comparable pairs of data points agree well. Further examination of the outliers is necessary to determine whether they can be attributed to wind-driven tilt and/or aerosol accumulation on the instruments. In order to see how the ocean-based validation compares with land-based validation, we made SRB-BSRN monthly mean shortwave/longwave radiation comparisons in the tropical region only, where all the buoys are moored. The results show that in the case of shortwave radiation, the bias error from the ocean-based validation is somewhat larger than its land-based counterpart, but their RMS errors are not significantly different. In the case of longwave radiation, the ocean-based and land-based validations show nearly identical comparison statistics.

Taiping Zhang↗
NASA NTRSDate not supplied

Comparison Study of Machine Learning Techniques to Predict Flight Energy Consumption for Advanced Air Mobility

This paper addresses the need to predict the flight energy consumption of aerial vehicles in the presence of wind using machine learning techniques. The presented work is critical to achieving sustainable and efficient operations for Advanced Air Mobility (AAM) and to evaluating the readiness of the ground-supporting energy infrastructure, e.g., electric grid and AAM portals. The flight energy consumption is described using the "energy per meter" (EPM) metric. We present a comparison study of influential machine learning techniques in predicting EPM using real-world flight test data. We presented new results of using the Decision Tree, Random Forest, and linear regression techniques, along with our previous results using the Recurrent Neural Network and Feed Forward Neural Network techniques. The comparison results show that the Linear Regression method outperforms other methods on the basis of the Mean Squared Error and error variance.

Machine Learning↗
NASA NTRS1995

High energy collimating fine grids

The objective of this project was to demonstrate the fabrication of extremely tight tolerance collimating grids using a high-Z material, specifically tungsten. The approach taken was to fabricate grids by a replication method involving the coating of a silicon grid substrate with tungsten by chemical vapor deposition (CVD). A negative of the desired grid structure was fabricated in silicon using highly wafering techniques developed for the semiconductor industry and capable of producing the required tolerances. Using diamond wafering blades, a network of accurately spaced slots was machined into a single-crystal silicon surface. These slots were then filled with tungsten by CVD, via the hydrogen reduction of tungsten hexafluoride. Following tungsten deposition, the silicon negative was etched away to leave the tungsten collimating grid structure. The project was divided into five tasks: (1) identify materials of construction for the replica and final collimating grid structures; (2) identify and implement a micromachining technique for manufacturing the negative collimator replicas (performed by NASA/JPL); (3) develop a CVD technique and processing parameters suitable for the complete tungsten densification of the collimator replicas; (4) develop a chemical etching technique for the removal of the collimator replicas after the tungsten deposition process; and (5) fabricate and deliver tungsten collimating grid specimens.

Arrieta, Victor M.↗
NASA NTRSDate not supplied

Artificial Neural Network (ANN) Surface Longwave and Shortwave Fluxes Trained on CERES Observations

The Clouds and Earth’s Radiant Energy System (CERES) project provides satellite-based observations of the radiative fluxes and clouds systems. CERES climate quality data products typically take several months of calibration and validation before release to the public. The Fast Longwave and Shortwave Radiative Flux (FLASHFlux) data product was developed to provide key data for the applied sciences and educational users within a week of observation. FLASHFlux achieves this by using simplified calibration, an operational meteorological product from Global Modeling and Assimilation Office (GMAO), and its own surface parameterizations model. The CERES FLASHFlux provides two data products: 1) an hourly Level 2 Single Scanner Footprint (SSF) data separately for Terra and NOAA-20 observations, and 2) a daily Level 3 Time Interpolated and Spatially Averaged (TISA) 1o x 1o gridded data that combines Terra and NOAA-20 observations. Currently, FLASHFlux uses the Langley Parameterized Shortwave Algorithm (LPSA) and Langley Parameterized Longwave Algorithm (LPLA) to derive its surface fluxes (Kratz et al., 2010; Gupta et al, 2001). A new Machine Learning (ML) based approach using Artificial Neural Networks to derive Surface Longwave (LW) & Shortwave (SW) fluxes based on training data from the CERES Clouds Radiative Swath (CRS) product is being investigated to replace LPSA and LPLA in the SSF surface flux products. One of the biggest hurdles in training ML model is model fitting. To overcome the problem of overfitting we use feature engineering that helps in finding the important feature and remove features that are irrelevant to the model. In our training we employed the Leave-One-Feature-Out Importance (LOFO) to evaluate the significance of each feature in our training. We intercompare ANN fluxes against surface fluxes produced from the Fu-Liou model in CRS and the LPSA/LPLA in FLASHFlux SSF. Furthermore, we validated ANN derived fluxes to the Baseline Surface Radiation Network (BSRN).

P C Sawaengphokhai↗
NASA NTRS1986

Analysis of Doppler lidar wind measurements

Doppler lidar and multiple Doppler radar data were obtained in a convectively mixed planetary boundary layer. The lidar measurements were possible due to scattering from existing aerosols; radar reflecting chaff was released in the atmosphere to make it visible to the multiple Doppler radar network. The data were analyzed to obtain detailed horizontal wind structures. The divergence of the horizontal wind was calculated and the anelastic continuity equation integrated to obtain vertical air motions. Differences between the areally averaged quantities and the grid point values provided a measure of the fluctuations in the wind components or the turbulent wind fluctuations. Vertical profiles of the mean winds and quantities related to the turbulent kinetic energy components and the turbulent momentum transfers were also calculated.

Srivastava, R. C.↗
NASA NTRS2006

Long-Term Validation and Variability of the Shortwave and Longwave Radiation Data of the GEWEX Surface Radiation Budget (SRB) Project

In this investigation, we make systematic Surface Radiation Budget-Baseline Surface Radiation Network (SRB-BSRN), Surface Radiation Data Centre (SRB-WRDC) and Surface Radiation Budget-Global Energy Balance Archive (SRB-GEBA) comparisons for both shortwave and longwave daily and monthly mean radiation fluxes at the Earth's surface. We first have an overview of all the comparable pairs of data in scatter or scatter density plots. Then we show the time series of the SRB data at grids in which there are ground sites where longterm records of data are available for comparison. An overall very good agreement between the SRB data and ground observations is found. To see the variability of the SRB data during the 21.5 years, we computed the global mean and its linear trend. No appreciable trend is detected at the 5% level. The empirical orthogonal functions (EOF) of the SRB deseasonalized shortwave downward flux are computed over the Pacific region, and the first EOF coefficient is found to be correlated with the ENSO Index at a high value of coefficient of 0.7083.

Zhang, Taiping↗
NASA NTRS1977

Materials and techniques for spacecraft static charge control

An overview of the design, development, fabrication, and testing of transparent conductive coatings and conductive lattices deposited or formed on high resistivity spacecraft dielectric materials to obtain control static charge buildup on spacecraft external surfaces is presented. Fabrication techniques for the deposition of indium/tin oxide coatings and copper grid networks on Kapton and FEP Teflon films and special frit coatings for OSR and solar cell cover glasses are discussed. The techniques include sputtering, photoetching, silkscreening, and mechanical processes. A facility designed and built to simulate the electron plasma at geosynchronous altitudes is described along with test procedures. The results of material characterizations as well as electron irradiation aging effects in this facility for spacecraft polymers treated to control static charge are presented. The data presents results for electron beam energies up to 30 kV and electron current densities of 30 nA/cm squared. Parameters measured include secondary emission, surface leakage, and through the sample currents as a function of primary beam energy and voltage.

Amore, L. J.↗
NASA NTRS2018

Soil Moisture Active Passive (SMAP) Project Assessment Report for Version 4 of the L4_SM Data Product

This report provides an assessment of Version 4 of the SMAP Level 4 Surface and Root Zone Soil Moisture (L4_SM) product, released on 14 June 2018. The assessment includes comparisons of L4_SM soil moisture and temperature estimates with in situ measurements from core validation sites and sparse networks. The assessment further includes a global evaluation of the internal diagnostics from the ensemble-based data assimilation system that is used to generate the L4_SM product, including observation-minus-forecast (O-F) brightness temperature residuals and soil moisture analysis increments.Together, the core validation site comparisons and the statistics of the assimilation diagnostics areconsidered primary validation methodologies for the L4_SM product. Comparisons against in situ measurements from regional-scale sparse networks are considered a secondary validation methodology because such in situ measurements are subject to upscaling errors from the point-scale to the grid-cell scale of the data product.The Version 4 L4_SM product benefits from an improved land surface modeling system and from retrospective surface meteorological forcing data that are as consistent as possible with the present-day datain terms of their climatology. Specifically, the model changes include revised parameters and parameterizations for (i) the surface energy balance, (ii) recharge from below of the model's surface excess reservoir, and (iii) the snow depletion curve. Updated ancillary inputs include improved datasets for landcover, topography, and vegetation height. The Version 4 algorithm further includes a revised approach to precipitation corrections that improves the precipitation climatology in Africa and the high-latitudes. Moreover, for system calibration the model is forced retrospectively with MERRA-2 reanalysis data, which are more consistent with the near-real time GEOS forward processing (FP) data used during the SMAP period than the retrospective GEOS data that were available for previous L4_SM versions. An analysis of the time-average surface and root zone soil moisture shows that the global pattern ofarid and humid regions is captured by the Version 4 L4_SM estimates. Owing to the changes in the landsurface modeling system, surface soil moisture is typically drier by several volumetric percent in Version 4 compared to Version 3, whereas root zone soil moisture is wetter in Version 4 in some regions and drierin others. Because of these climatological differences, the Version 3 and Version 4 products should not be combined into a single dataset for use in applications.Results from the core validation site comparisons indicate that Version 4 of the L4_SM data product meets the self-imposed L4_SM accuracy requirement, which is formulated in terms of the RMSE after removal of the long-term mean difference (ubRMSE). The overall ubRMSE of the 3-hourly L4_SM dataat the 9 km scale is 0.039 m3 m-3 for surface soil moisture and 0.029 m3 m-3 for root zone soil moisture,below the 0.04 m3 m-3 requirement. The L4_SM estimates are an improvement over estimates from a model-only Nature Run version 7.2 (NRv7.2), which demonstrates the beneficial impact of the SMAP brightness temperature data. Overall, L4_SM surface and root zone soil moisture estimates are more skillful than NRv7.2 estimates, with statistically significant improvements at the 5% level for surface soil moisture R and anomaly R values. Results from comparisons of the L4_SM product to i

Reichle, Rolf H.↗