Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “EUTECTIC ALLOY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Thermal reliability of Al-Si eutectic alloy for thermal energy storage

Highlights: • Thermal reliability of material is investigated after long time vacuum thermal cycling. • The latent heat of fusion show almost no change after 1000 thermal cycles. • The thermal conductivity exhibit a good stability after 1000 cycles. • Al-Si eutectic alloy is a potentially good candidate for thermal energy storage applications. - Abstract: The thermal reliability of Al-Si eutectic alloy as phase change materials (PCMs) was investigated through vacuum thermal cycling 250, 500, 750, and 1000 times going through the solid-liquid phase change. The changes in thermal properties of Al-Si eutectic alloy, including melting point, latent heat, specific heat, thermal diffusivity and thermal conductivity, were investigated using differential scanning calorimetric (DSC) and laser flash apparatus. The results revealed that, with increasing the number of cycles, the melting point and latent heat of fusion of the Al-Si eutectic alloy showed almost no changes. Moreover, the thermal conductivity showed an outstanding stability after 1000 thermal cycles. Therefore, it is concluded that the thermal reliability of Al-Si eutectic alloy is more than adequate for long-term performance as a phase change material for thermal energy storage (TES) applications.

36 MATERIALS SCIENCE↗

Mechanical behavior of the directionally solidified gamma/gamma prime - delta eutectic alloy

The eutectic alloy Ni-20.0%Cb-2.5%Al-6.0%Cr was tested in short-term creep and long-term exposure to service conditions to assess its suitability for high temperature turbine blade applications. Long-time exposure showed the lamellar microstructure of the alloy to be exceptionally stable. Other properties tested were notch sensitivity, isothermal and thermomechanical fatigue strength, shear strength, and transverse ductility. It was shown that this alloy is superior to the best currently available directionally solidified superalloys over the temperature/stress conditions encountered in turbine airfoils.

Barkalow, R. H.↗

Directionally solidified iron-base eutectic alloys

Pseudobinary eutectic alloys with nominal compositions of Fe-25Ta-22Ni-10Cr and Fe-15.5Nb-14.5Ni-6.0Cr were directionally solidified at 0.5 centimeter per hour. Their microstructure consisted of the fcc, iron solid-solution, matrix phase reinforced by about 41-volume-percent, hcp, faceted Fe2Ta fibers and 41-volume-percent, hcp, Fe2Nb lamellae for the tantalum- and niobium-containing alloys, respectively. The microstructural stability under thermal cycling and the temperature dependence of tensile properties were investigated. These alloys showed low elevated-temperature strength and were not considered suitable for application in aircraft-gas-turbine blades although they may have applicability as vane materials.

Tewari, S. N.↗

A Directionally Solidified Iron-chromium-aluminum-tantalum Carbide Eutectic Alloy

A eutectic alloy, Fe-13.6CR-3.7Al+9TaC, was directionally solidified in a high gradient furnace, producing a microstructure of alined TaC fibers in an oxidation resistant alpha-iron matrix. Tensile and stress rupture properties, thermal cycling resistance, and microstructures were evaluated. The alloy displays at 1000 C an ultimate tensile strength of 58 MPa and a 100-hour rupture life at a stress of 21 MPa. Thermal cycling to 1100 C induces faceting in the TaC fibers.

Harf, F. H.↗

The microstructure of MnBi/Bi eutectic alloys

Directionally solidified eutectic alloys of the system MnBi/Bi have been investigated with reference to the dependence of the fiber spacing on the growth rate and the interfacial temperature gradient. It is found that the fiber spacing varies as the inverse square root of the growth rate and does not depend on the temperature gradient in contrast to the claims that all faceted/non-faceted eutectics should show a temperature gradient influence.

Ravishankar, P. S.↗

Directionally solidified eutectic alloy gamma-beta

A pseudobinary eutectic alloy composition was determined by a previously developed bleed-out technique. The directionally solidified eutectic alloy with a composition of Ni-37.4Fe-10.0Cr-9.6Al (in wt%) had tensile strengths decreasing from 1,090 MPa at room temperature to 54 MPa at 1,100 C. The low density, excellent microstructural stability, and oxidation resistance of the alloy during thermal cycling suggest that it might have applicability as a gas turbine vane alloy while its relatively low high temperature strength precludes its use as a blade alloy. A zirconium addition increased the 750 C strength, and a tungsten addition was ineffective. The gamma=beta eutectic alloys appeared to obey a normal freezing relation.

Tewari, S. N.↗

Low-temperature bonding with spaced nanorods and eutectic alloys

Bonded surfaces are formed by adhering first nanorods and second nanorods to respective first and second surfaces. The first shell is formed on the first nanorods and the second shell is formed on the second nanorods, wherein at least one of the first nanorods and second nanorods, and the first shell and the second shell are formed of distinct metals. The surfaces are then exposed to at least one condition that causes the distinct metals to form an alloy, such as eutectic alloy having a melting point below the temperature at which the alloy is formed, thereby bonding the surfaces upon which solidification of the alloy.

36 MATERIALS SCIENCE↗

Influence of Growth Rate on Eutectic Spacing, Microhardness, and Ultimate Tensile Strength in the Directionally Solidified Al-Cu-Ni Eutectic Alloy

In this work, the mechanical properties of the Al-Cu-Ni eutectic alloy, Al-32.5 wt pct Cu-1 wt pct Ni, were investigated in terms of the dependency on growth rates. The Al-Cu-Ni eutectic alloy was directionally solidified at a constant temperature gradient, G = 4.93 K mm{sup −1}, with a wide range of growth rates (V = 9.25 to 2056.68 µm s{sup −1}) using a Bridgman-type directional solidification furnace. The eutectic spacing (λ), microhardness (HV{sub T}), and ultimate tensile strength (σ{sub UTS}) were measured with standard techniques. The dependences of λ, HV{sub T}, and σ{sub UTS} on V for directionally solidified Al-Cu-Ni eutectic alloy were experimentally obtained using regression analysis. The results obtained in the present work were compared with the similar experimental results in the literature. Finally, the elastic energy dependence on growth rates for Al-32.5 wt pct Cu-1 wt pct N alloy was determined from their nominal stress–strain plots.

36 MATERIALS SCIENCE↗

Feasibility study of tungsten as a diffusion barrier between nickel-chromium-aluminum and Gamma/Gamma prime - Delta eutectic alloys

Coating systems proposed for potential use on eutectic alloy components in high-temperature gas turbine engines were studied with emphasis on deterioration of such systems by diffusion. A 1-mil thick W sheet was placed between eutectic alloys and a NiCrAl layer. Layered test specimens were aged at 1100 C for as long as long as 500 hours. Without the W barrier, the delta phase of the eutectic deteriorated by diffusion of Nb into the NiCrAl. Insertion of the W barrier stopped the diffusion of Nb from delta. Chromium diffusion from the NiCrAl into the gamma/gamma prime phase of the eutectic was greatly reduced by the barrier. However, the barrier thickness decreased with time; and W diffused into both the NiCrAl and the eutectic. When the delta platelets were alined parallel to the NiCrAl layer, rather than perpendicular, diffusion into the eutectic was reduced.

Young, S. G.↗

Stability of several oxide dispersion strengthened alloys and a directionally solidified gamma/gamma prime-alpha eutectic alloy in a thermal gradient

Thermal gradient testing of three oxide dispersion strengthened alloys (two Ni-base alloys, MA 754 and MA 6000 E, and the Fe-base MA 956) and the directionally solidified eutectic alloy, gamma/gamma prime-alpha, have been conducted. Experiments were carried out with maximum temperatures up to 1200 C and thermal gradients on the order of 100 C/mm. The oxide dispersion strengthened alloys were difficult to test because the thermal stresses promoted crack nucleation and growth; thus the ability of these alloys to maintain a thermal gradient may be limited. The stability of individual fibers in gamma/gamma prime-alpha was excellent; however, microstructural changes were observed in the vicinity of grain boundaries. Similar structures were also observed in isothermally annealed material; therefore thermal gradients do not affect the microstructure of gamma/gamma prime-alpha in any significant manner.

Staniek, G.↗

A feasibility study of a diffusion barrier between Ni-Cr-Al coatings and nickel-based eutectic alloys

Coating systems have been proposed for potential use on eutectic alloy components in high-temperature gas turbine engines. In a study to prevent the deterioration of such systems by diffusion, a tungsten sheet 25 microns thick was placed between eutectic alloys and an Ni-Cr-Al layer. Layered test specimens were aged at 1100 C for as long as 500 h. Without the tungsten barrier the delta phase of the eutectic deteriorated by diffusion of niobium into the Ni-Cr-Al. Insertion of the tungsten barrier stopped the diffusion of niobium from the delta phase. Chromium diffusion from the Ni-Cr-Al into the gamma/gamma-prime phase of the eutectic was greatly reduced by the barrier. However, the barrier thickness decreased with time, and tungsten diffused into both the Ni-Cr-Al and the eutectic. When the delta platelets were aligned parallel rather than perpendicular to the Ni-Cr-Al layer, diffusion into the eutectic was reduced.

Young, S. G.↗

Effect of laser surface remelting on the microstructure and properties of Al-Al2Cu-Si ternary eutectic alloy

Bimodal ultrafine eutectic composites (BUECs) exhibit a good combination of strength and plasticity owing to a dual-hierarchy in eutectic length-scales in the microstructure. The present study investigates the variation of phase, morphology, feature length-scales and modality of microstructures obtained in a Al81Cu13Si6 (at. %) ternary alloy after laser surface remelting. A novel approach of varying component bimodal eutectic volume fractions by controlling the cooling rate of the laser solidification process has been presented. The volume fraction of the fine eutectic matrix has a profound effect on the flow strength. Laser remelted microstructures with volume fractions of the fine eutectic varying from 25 to 40% exhibiting compressive flow strengths ranging from 500 to 900MPa have been obtained. The volume fraction of the fine eutectic decreased with cooling rate and completely ceased to exist at cooling rates greater than 4 × 10 °C/s 4 .

36 MATERIALS SCIENCE↗