Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “EPRI”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Assessment of EPRI’s Tan Delta Approach to Manage Cables in Submerged Environments: Statistical Review of EPRI Data

Research conducted by the Electric Power Research Institute (EPRI) and other research institutions have concluded that water-trees are one of the leading degradation mechanisms that contribute to the loss of dielectric insulation strength in medium-voltage cable insulating materials in wet or submerged environments. The electrochemical reactions are caused by the combined effect of water presence and relatively high electrical stress. Records of cable failures provided by the licensees in response to Generic Letter (GL) 2007-01 (NRC 2007) have called into question the reliability of medium voltage cables in wetted or submerged environments. EPRI’s dissipation factor or Tan Delta testing guidelines and acceptance criteria have been adopted by most nuclear power plant operators as the primary tool for condition monitoring of medium voltage cables in wet or submerged environments. EPRI has been collecting member data since late 2009 to analyze and provide feedback to members, validate the EPRI-developed acceptance criteria guidelines, support analysis of test results, recommend appropriate actions for the "action required" category, and gather candidate cables for EPRI-sponsored forensic research on causes for insulation degradation. EPRI has collected data from 37 nuclear sites, which represent 44 operating units. The test results have been organized by insulation type, such as cross-linked polyethylene (XLPE); butyl rubber; black, pink, and brown ethylene-propylene rubber (EPR); and compact insulation (black and pink EPR)1. The data have been analyzed, and follow-up information was obtained from members for “action required” test results. EPRI has also performed correlations between Tan Delta tests and the information gathered under the EPRI forensic research on medium-voltage cables. In addition, EPRI has developed guidance by cable insulation type on how to systematically analyze Tan Delta test results. The analysis described here reviewed the two primary EPRI reports (EPRI 3002000557 and EPRI 3002005321) as well as two precedent EPRI reports (EPRI 1028262 and EPRI 1021070) that were cited in the primary reports. The principal results and conclusions from the project analyses are provided.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

EPRI Research Results: The EPRI Implementation Guide for the NRC BTP on Concentration Averaging and Encapsulation - 17488

The Nuclear Regulatory Commission published Revision 1 of the Branch Technical Position (BTP) on 'Concentration Averaging and Encapsulation' (BTP 2015.) PRI developed an Implementation Guide for applying BTP 2015 to nuclear power plant specific waste streams. This Implementation Guide has been vetted and supported by an EPRI organized working group consisting of industry participants (including utilities subject matter experts, disposal sites, NRC and Agreement State representatives and industry experts) will ensure compliant and consistent application during waste generation, packaging, processing and disposal activities. The Implementation Guide provides for a comparison to previous BTP guidance and provides clarification and common understanding of the key concepts contained within the revised BTP. These include averaging constraints, hot spots, waste streams, waste types, discrete items, blending, solidification, encapsulation and alternative approaches. EPRI published the Implementation Guidance for the Nuclear Regulatory Commission Branch Technical Position on 'Concentration Averaging and Encapsulation, Revision 1' (EPRI Report 3002008189) in the September 2016 and it was made available to the public. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

As-run physics analysis for the EPRI-3 experiment for cycles 155B and 158B

The purpose of this Engineering Calculations Analysis Report (ECAR) is to document the as-run heat generation rates (W/g), flux/fluence, radio-isotopic source term in Curies and grams, decay heat rate in Watts, and specimen DPA for the post-irradiation shipment and examination of the Electric Power Research Institute (EPRI)-3-1 and EPRI-3-2 experiments. EPRI-3-1 was irradiated during cycle 155B ending April 12, 2014. EPRI-3-2, a modification of EPRI-3-1, was irradiated during cycle 158B ending April 1, 2016. Source term, decay heat rate, and DPA calculations were based on scaled Monte Carlo N-Particle (MCNP) calculated fluxes for the EPRI-3-2 experiment. Although EPRI-3-2 is a modification of EPRI-3-1, no significant changes were made in the placement of experiment specimens. Calculated fluxes were scaled using as-run center lobe source powers of the corresponding irradiation cycles for EPRI-3-1 and EPRI-3-2. ORIGEN2 Version 2.2 was used to determine the decay heat rate and source term for the EPRI-3 experiment. The source term analysis was performed as requested by the project staff. The results of this analysis may be used to demonstrate compliance with shipping requirements in the BEA Research Reactor (BRR) cask following irradiation as well as to provide as-run source term to support Post-Irradiation Examination (PIE).

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

EPRI Demonstration of an Autonomous Site Characterization Vehicle - 20523

A substantial effort is applied in performing radiological characterization of structures and land areas during decommissioning of a nuclear facility. This includes multiple surveys of land areas and large structures to support eventual site release under the Multi Agency Survey and Site Investigation Manual (MARSSIM, Reference 1). These surveys are typically performed using manually delivered systems, which is time consuming and labor intensive. Radiological surveys intentionally follow a prescribed protocol with respect to areas covered, scan speeds, responses to elevated readings, required detector offsets, the need for repeat measurements, etc. Based on these attributes, combined with the repetitive effort of performing surveys over large areas, automation of radiological characterization techniques has a high potential to be successful and promises substantial benefit. EPRI has performed a project that resulted in the development and demonstration of an autonomous site characterization system. This EPRI project focused on building surfaces and the surfaces of large land areas as these configurations lend themselves more readily to automated survey. The project included: - Identification of the requirements for an autonomous site characterization system; - A survey of existing control systems that use automation to conduct characterization of structures and land areas. - As no fully adequate systems were identified, a complete system was developed that utilized commercially available detection and analysis systems and a self driving vehicle owned by EPRI. The system was demonstrated at the Kewaunee nuclear power plant site in the fall of 2019. The demonstration included: - Autonomous surveys of floor areas inside the Auxiliary Building at Kewaunee after manually controlled mapping of the survey areas. - For land areas, the vehicle autonomously surveyed areas using travel paths had been preprogrammed onto an internet available map of area. In this case, GPS coordinates from the preprogramming were used for navigation by the vehicles guidance system. This paper summarizes the characterization system development and system demonstration which will also be published in an EPRI report in the first half of 2020. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Baseline Fracture Toughness and CGR Testing of Alloys X-750 and XM-19 (EPRI Phase I)

The Advanced Test Reactor National Scientific User Facility (ATR NSUF) and Electric Power Research Institute (EPRI) formed an agreement to test representative alloys used as reactor structural materials as a pilot program toward establishing guidelines for future ATR NSUF research programs. This report contains results from the portion of this program established as Phase I (of three phases) that entails baseline fracture toughness, stress corrosion cracking (SCC), and tensile testing of selected materials for comparison to similar tests conducted at GE Global Research. The intent of this Phase I research program is to determine baseline properties for the materials of interest prior to irradiation, and to ensure comparability between laboratories using similar testing techniques, prior to applying these techniques to the same materials after having been irradiated at the Advanced Test Reactor (ATR). The materials chosen for this research are the nickel based super alloy X-750, and nitrogen strengthened austenitic stainless steel XM-19. A spare core shroud upper support bracket of alloy X-750 was purchased by EPRI from Southern Co. and a section of XM-19 plate was purchased by EPRI from GE-Hitachi. These materials were sectioned at GE Global Research and provided to INL.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE-NE Light Water Reactor Sustainability Program and EPRI Long-Term Operations Program. Joint Research and Development Plan

Nuclear power has contributed almost 20% of the total amount of electricity generated in the United States over the past two decades. High capacity factors and low operating costs make nuclear power plants (NPPs) some of the most economical power generators available. Further, nuclear power remains the single largest contributor (nearly 70%) of non-greenhouse gas-emitting electric power generation in the United States. Even when major refurbishments are performed to extend operating life, these plants continue to represent cost-effective, low-carbon assets to the nation’s electrical generation capability. By the end of 2014, about one-third of the existing domestic fleet will have passed their 40th anniversary of power operations, and about one-half of the fleet will reach the same 40-year mark within this decade. Recognizing the challenges associated with pursuing extended service life of commercial nuclear power plants, the U.S. Department of Energy’s (DOE) Office of Nuclear Energy (NE) and the Electric Power Research Institute (EPRI) have established separate but complementary research and development programs (DOE-NE’s Light Water Reactor Sustainability [LWRS] Program and EPRI’s Long-Term Operations [LTO] Program) to address these challenges. To ensure that a proper linkage is maintained between the programs, DOE-NE and EPRI executed a memorandum of understanding in late 2010 to “establish guiding principles under which research activities (between LWRS and LTO) could be coordinated to the benefit of both parties.” This document represents the third annual revision to the initial version (March 2011) of the plan as called for in the memorandum of understanding.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Irradiation and PIE of alloys X-750 and XM-19 (EPRI Phase III)

The Nuclear Science User Facilities (NSUF) based at Idaho National Laboratory (INL), along with the Electric Power Research Institute (EPRI), formed an agreement to test representative alloys used as reactor structural materials as a pilot program to establish guidelines for future NSUF research programs. This report contains results from the portion of this program established as Phase III (of three phases), entailing irradiation and post-irradiation examination of select alloys typical of boiling water reactor (BWR) internal structural materials. Phases I and II are the subject of separate reports and represent baseline material test results and irradiation experiment design, respectively. The intent of this Phase III research program is to determine properties for the materials of interest after being irradiated at the Advanced Test Reactor (ATR) to three different target fast (E>1MeV) fluences: 5.0 x 10¹⁹ n/cm², 2.0 x 10²⁰ n/cm², and 1.0 x 10²¹ n/cm². These correspond to irradiation damage levels (displacements per atom [dpa]) of approximately 0.08, 0.30, and 1.4 dpa, which represent comparable levels to (a) a previous study which looked at X-750 irradiated to ~1 x 10¹⁹ n/cm², comparable to the lowest fluence; (b) approximately a medium level of fluence for BWR components; and (c) extended life (60 – 80 years) for BWR components. The materials chosen for this research are the nickel-based alloy X-750 and austenitic stainless steel XM-19. A spare core shroud upper support bracket of alloy X-750 was purchased by EPRI from Southern Co., and a section of XM-19 plate was purchased by EPRI from GE-Hitachi. These materials were sectioned at GE Global Research Center (GE-GRC), and parts were provided to INL for use in this pilot project.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Irradiation and PIE of alloys X-750 and XM-19 (EPRI Phase III)

The Nuclear Science User Facilities (NSUF) based at Idaho National Laboratory (INL), along with the Electric Power Research Institute (EPRI), formed an agreement to test representative alloys used as reactor structural materials as a pilot program to establish guidelines for future NSUF research programs. This report contains results from the portion of this program established as Phase III (of three phases), entailing irradiation and post-irradiation examination of select alloys typical of boiling water reactor (BWR) internal structural materials. Phases I and II are the subject of separate reports and represent baseline material test results and irradiation experiment design, respectively. The intent of this Phase III research program is to determine properties for the materials of interest after being irradiated at the Advanced Test Reactor (ATR) to three different target fast (E>1MeV) fluences: 5.0 x 10¹⁹ n/cm², 2.0 x 10²⁰ n/cm², and 1.0 x 10²¹ n/cm². These correspond to irradiation damage levels (displacements per atom [dpa]) of approximately 0.08, 0.30, and 1.4 dpa, which represent comparable levels to (a) a previous study which looked at X-750 irradiated to ~1 x 10¹⁹ n/cm², comparable to the lowest fluence; (b) approximately a medium level of fluence for BWR components; and (c) extended life (60 – 80 years) for BWR components. The materials chosen for this research are the nickel-based alloy X-750 and austenitic stainless steel XM-19. A spare core shroud upper support bracket of alloy X-750 was purchased by EPRI from Southern Co., and a section of XM-19 plate was purchased by EPRI from GE-Hitachi. These materials were sectioned at GE Global Research Center (GE-GRC), and parts were provided to INL for use in this pilot project.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

As-run physics analysis for the EPRI-2 experiment for cycle 153B

The purpose of this ECAR is to document the as-run physics analysis and source term in Curies and decay heat rate (Watts) for the shipment of the EPRI-2 experiment located in the Center Flux Trap (CFT). EPRI-2 was irradiated during cycle 153B. The experiment irradiation ended on April 13, 2013. The as-run heat rates and flux/fluence results were calculated using the MCNP ATR full core model. The heat rates and flux are calculated based on an average center lobe power of 30.8 MW. The fluence is based on the operating time of 13.45 days. ORIGEN2 Version 2.2 is used to determine the decay heat rate, gamma spectrum, and source term for the EPRI-2 experiment. The source term analysis was performed as requested by the project staff to demonstrate compliance with shipping requirements in the GE-2000 cask following irradiation as well as provide an estimated source term to support Post-Irradiation Examination as needed.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

As-Run Physics Analysis for the EPRI-1 Experiment

The purpose of this ECAR is to document the as-run physics analysis for the Electric Power Research Institute (EPRI)-1 experiment located in the Center Flux Trap (CFT). EPRI-1 was irradiated during cycle 157C. The experiment irradiation ended on February 15, 2015. The as-run heat rates, DPA, and flux/fluence results were calculated using the Monte Carlo N-Particle (MCNP) Advanced Test Reactor (ATR) full core model. The heat rates, DPA, and flux are calculated based on an average center lobe power of 21.1 MW. The fluence and DPA is based on the operating time of 5.4 days. ORIGEN2 Version 2.2 was used to calculate the isotopic concentration in grams for the EPRI-1 experiment. The source term analysis was performed as requested by the project staff. The results of this analysis may be used to support Post-Irradiation Examination (PIE)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Baseline Fracture Toughness and CGR testing of alloys X-750 and XM-19 (EPRI Phase I)

The Advanced Test Reactor National Scientific User Facility (ATR NSUF) and Electric Power Research Institute (EPRI) formed an agreement to test representative alloys used as reactor structural materials as a pilot program toward establishing guidelines for future ATR NSUF research programs. This report contains results from the portion of this program established as Phase I (of three phases) that entails baseline fracture toughness, stress corrosion cracking (SCC), and tensile testing of selected materials for comparison to similar tests conducted at GE Global Research. The intent of this Phase I research program is to determine baseline properties for the materials of interest prior to irradiation, and to ensure comparability between laboratories using similar testing techniques, prior to applying these techniques to the same materials after having been irradiated at the Advanced Test Reactor (ATR). The materials chosen for this research are the nickel based super alloy X-750, and nitrogen strengthened austenitic stainless steel XM-19. A spare core shroud upper support bracket of alloy X-750 was purchased by EPRI from Southern Co. and a section of XM-19 plate was purchased by EPRI from GE-Hitachi. These materials were sectioned at GE Global Research and provided to INL.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

IM3 + EPRI Data Center Load Projections

This dataset contains scenarios of hourly total electricity demand with and without projected loads from data centers over the period 2022-2040. The root projections without data center demands are identical to those documented in Burleyson et al. 2024. In short, those projections encompass hourly electricity demands for 54 Balancing Authorities (BAs) in the United States across a range of eight of weather and socioeconomic scenarios. Refer to the root dataset and accompanying publication, Burleyson et al. 2025, for information about how those projections were generated. For this derivative dataset we used the base loads from the following scenarios: rcp45hotter_ssp3 rcp45hotter_ssp5 rcp85hotter_ssp3 rcp85hotter_ssp5 The root load projections did not reflect the drastic expansion of data centers that has occurred in the last several years to support artificial intelligence and cloud computing. To reflect growth in data center demand, a second set of load projections were created in which we layered in additional data center load projections based on the data center load growth scenarios described in a 2024 report by the Electric Power Research Institute (EPRI): "Powering Intelligence: Analyzing Artificial Intelligence and Data Center Energy Consumption". The EPRI projections from the report are included in this dataset (EPRI_2024_Projections.xlsx). That report contained annual state-level data center load projections for four year-over-year growth rates for data center demands: Low (3.71% annual growth) Moderate (5% annual growth) High (10% annual growth) Higher (15% annual growth) To homogenize the load projections with and without data centers we had to get them to a common scale. The first step was to take the EPRI annual state-level data center energy consumption values and convert them to 8760-hr loads for each year. We did that by assuming a flat (e.g., not weather- or time-sensitive) load profile and distributing the data center loads in each state evenly across all hours in a year. From there the loads were downscaled from the state-level to the county-level using 2019 county-level populations as weights. Finally, the county-level hourly data center loads were summed to the BA-level using the county-to-BA mapping underpinning the root load projections. The net result is 16 (4 weather and socioeconomic scenarios crossed with 4 data center load growth scenarios) unique load projections for the period 2022-2040. The file format follows that of the root dataset with a single additional column "Scaled_TELL_BA_Load_with_DC_MWh" that contains the hourly loads with the added data center loads for a given BA-year-scenario combination. Please refer to the readme file in the root dataset for more information on the file format.

Burleyson, Casey [Pacific Northwest National Labor↗

EPRI Research Results: International Nuclear Power Plant Waste Classification - 17444

Different countries around the globe use varying schemes for the classification of radioactive waste. Many countries develop country specific waste classification schemes based on the International Atomic Energy Agency (IAEA) waste classification framework. The United States of America use the Class A, B, and C waste classification. Additionally, some countries use concentration limits to classify wastes while others use dose rate limits or a combination of concentration and dose rate limits. General comparisons have been made between the IAEA and the United States classification schemes, but a clear and well researched comparison of the international schemes was not evident in the available research data sets. In 2013 Electric Power Research Institute (EPRI) initiated the Comparison of Global Low and Intermediate Level Waste Management Methods project. The objective of the project was to understand how six countries managed their low and intermediate level wastes from generation to disposal. A major task of this project was to conduct a comparison of the international waste classification schemes. EPRI developed a set of reference waste volumes that are representative of nuclear power plant low-level radioactive waste in form and radioactivity concentrations (e.g. dry active waste, high activity resin, low activity resin, high activity filters and low activity filters). These waste volumes were then classified using the waste classification systems in place in several countries around the world. In 2016, EPRI presented a paper providing a status update on this research. This 2017 paper provides the final results of that research, show where comparisons and correlations can be made, and provide a discussion on how this information might inform international radioactive research and development and benchmarking of radioactive waste management strategies, operational experiences, best practices, and technology implementation. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Application of the EPRI depletion reactivity benchmarks - 14423

The EPRI measured-based depletion reactivity benchmarks intend to facilitate the validation of burnup credit by validating the combined effect of changes in isotopic content and cross-sections. In the framework of burnup credit implementation for PWR fuels, this paper proposes to study the application of the EPRI benchmarks for a spent fuel pool criticality evaluation using the French tools: the DARWIN 2.2 depletion package and the CRISTAL V1 criticality safety package, both based on cross-section libraries from the JEF2.2 evaluation. For that purpose, the benchmarks are analyzed using the connection of DARWIN 2.2 with APOLLO2-MORET 4, allowing the determination of the bias for the reactivity decrement. Then, these results are used to define a bias to take into account in the criticality evaluation of a spent fuel pool. In addition, the benefit of the EPRI depletion reactivity benchmarks is assessed through a comparison with the validation approach adopted in France until now. The bias resulting from this latter approach is evaluated by 1) applying, to the calculated nuclides concentrations, isotopic penalizing factors derived from the comparison between calculated values of nuclide concentrations and experimental values obtained from used fuel chemical analyses from French reactors, 2) analyzing representative critical experiments. Additional analysis of the benchmarks using the connection of VESTA 2.1 with MORET 5 is performed as these codes allow calculations of complex 3D geometrical configurations and the use of various nuclear data libraries. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Light Water Reactor Sustainability Program FY13 Status Update for EPRI - RISMC Collaboration

The purpose of the Risk Informed Safety Margin Characterization (RISMC) Pathway research and development (R&D) is to support plant decisions for risk-informed margins management with the aim to improve economics, reliability, and sustain safety of current NPPs. Goals of the RISMC Pathway are twofold: (1) Develop and demonstrate a risk-assessment method coupled to safety margin quantification that can be used by NPP decision makers as part of their margin recovery strategies. (2) Create an advanced "RISMC toolkit" that enables more accurate representation of NPP safety margin. In order to carry out the R&D needed for the Pathway, the Idaho National Laboratory (INL) is collaborating with the Electric Power Research Institute (EPRI) in order to focus on applications of interest to the U.S. nuclear power industry. This report documents the collaboration activities performed between INL and EPRI during FY2013.

97 MATHEMATICS AND COMPUTING↗

Energy Systems Integration Collaborations: NREL + EPRI

This fact sheet highlights work done at the ESIF in collaboration with EPRI. NREL is collaborating with the Electric Power Research Institute (EPRI) to validate the performance of a Spirae-developed advanced microgrid controller capable of managing 1-10 megawatts of aggregated generation capacity. The aim is to develop a commercially viable and flexible microgrid controller, easily adapted to different end-user applications and to a range of electric grid characteristics.

30 DIRECT ENERGY CONVERSION↗

As-Run Physics Analysis for the EPRI Zirconium Growth C Capsule

This engineering calculation and analysis report documents the as-run nuclear-heating term, source-term, and radiation damage (measured in displacements per atom [dpa]) accumulation for the Electric Power Research Institute zirconium growth experiment's C capsule (EPRI-ZG-C). These data have been calculated using MCNP 6.1 and SCALE 6.2.3. These data can be used for: the shipping of the EPRI-ZG-C capsule, the acceptance of the capsule at the Materials and Fuels Complex, and programmatic scientific needs.

36 MATERIALS SCIENCE↗

EPRI Project Update on International Nuclear Power Plant Waste Classification - 16224

Countries around the globe use varying schemes for the characterization of radioactive waste. Many countries use adaptations of the International Atomic Energy Agency (IAEA) waste classification scheme. Other countries use the Class A, B, and C waste classification scheme that was developed in the United States. General comparisons have been made between the IAEA and the United States (U.S.) classification schemes, but a clear and well researched comparison of the two schemes was not evident in the available research data sets. The Electric Power Research Institute (EPRI) Radiation Safety (RS) Program has conducted a technical evaluation that compares these two waste characterization schemes. EPRI developed a set of reference wastes that are representative of nuclear power plant low-level radioactive waste in form and radioactivity concentrations (e.g. dry active waste, high activity resin, low activity resin, high activity filters and low activity filters). These reference wastes were then classified using the waste classification systems in place in several countries around the world. This paper and presentation will provide a summary of that research, show where strong comparisons and correlations can be made, and provide a discussion on how this information might inform the harmonization of global waste classification standards. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗