Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ELECTROLYSIS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Techno-economic analysis of offshore wind PEM water electrolysis for H 2 production

A model for producing hydrogen via offshore wind electrolysis was developed and the levelized costs of both energy and hydrogen were calculated. Here, this model calculated the cost of hydrogen produced by offshore wind and showed that the levelized cost of energy for hydrogen production and transportation to shore could be lower than for electricity transmission from offshore wind farms, using real wind data from a particular location. Therefore, direct coupling of the electrolysis system with offshore wind turbine is more advantageous than transmitting electricity to shore and then producing hydrogen via traditional electrolysis; the cost of hydrogen from offshore wind electrolysis is estimated to be $\$2.09$/kg, vs $\$3.86$/kg from traditional electrolysis using wind power.

08 HYDROGEN↗

Solid Oxide Based Electrolysis and Stack Technology with Ultra-High Electrolysis Current Density (>3A/cm 2 ) and Efficiency

Hydrogen, a valuable commodity gas, is increasingly recognized as an important fuel and energy storage pathway of the future. This project aims to develop an innovative solid oxide based electrolysis cell and stack technology with ultra-high steam electrolysis current (>3A/cm 2 ) for potentially ultra-low-cost, highly efficient hydrogen production from diverse renewable sources. In this project, solid oxide based high power density cells (HiPoD cells) were developed. Those cells demonstrated capability of operating at ultra-high electrolysis current density of 6 A/cm 2 at 1.67V. During a long term steady state electrolysis test, a HiPoD cell was operated for more than 1000 hours at 3 A/cm 2 with a low degradation rate of 1.8% per 1000 hours. A 20-cell electrolysis stack was built using HiPoD cells and an ultra-compact, low-cost stack design platform. This stack was used to explore the boundaries of high current density electrolysis operation and achieved an incredible stack current density of 3 A/cm 2 with an average cell voltage of only 1.493 V. The stack was further operated in steady-state electrolysis at 2 A/cm 2 for more than 1000 hours with an overall degradation of 0.57% per 1000 hours. With an improved understanding of electrolysis operation at ultra-high current density, a new compact stack architecture (CSA) design with scalability up to 55 kW (or 38 kg H 2 per day) was tested. A number of 45-cell CSA stack was built and demonstrated 10 kW and 245 g/hr hydrogen production at 1.8 A/cm 2 electrolysis current density. In addition to cell and stack development, a preliminary system design was developed by integrating the inputs from electrochemistry, cell/stack performance data, and system level implications of configuration and operational parameters. A module design was created based on a circular array of six stacks surrounded in a cool pressure vessel. Further architectural and controls strategies such as stack power control and instrumentation were determined through the development of the module. A comprehensive techno-economic study of an ultra-high current density SOEC system integrated with renewable energy sources has been conducted. To determine the estimated cost of hydrogen for the system, the H2A Current Distributed Hydrogen Production Model version 3.101 was applied. Annual system production cases at both commercial and industrial electricity rates as per the H2A model was analyzed. The option of meeting DOE 2020 Advanced Electrolysis Technologies targets were discussed. Feedstock electricity represents the bulk of projected hydrogen cost with either electricity rate. At an annual production volume of 250 units, H2A hydrogen cost of $2.3/kg can be achieved at electricity cost around 3.5¢/kWh.

08 HYDROGEN↗

Operando X-Ray Diffraction During High Temperature Electrolysis

This work presents the design, development, and deployment of an operando X-ray diffraction (XRD) system for high-temperature electrolysis (HTE), enabling real-time characterization of solid oxide electrolysis cells (SOECs) under true operational conditions. The integration of an HTE test stand within a synchrotron radiation environment, mimicking the conditions of a laboratory setup, aims to enhance our understanding of the degradation processes affecting the performance and longevity of SOECs. Utilizing a custom furnace and a high precision motor stack assembly at the Stanford Synchrotron Radiation Lightsource (SSRL), the system revealed unparalleled insights into the structural evolution of SOEC components through various operational stages, including initial heat ramp, cell reduction, fuel ramp, and wet electrolysis. Initial results demonstrate the significant impact of the initial heating and cooling on secondary phase formation within the SOEC, highlighting the utility of operando XRD for developing more efficient and durable hydrogen production technologies.

08 HYDROGEN↗

Voltage cycling as a dynamic operation mode for high temperature electrolysis solid oxide cells

Solid Oxide Electrolysis Cells (SOECs) have emerged as a promising technology for the efficient production of H2 via high-temperature electrolysis. However, power input from dynamic energy sources remains a significant challenge for their long-term stability. It is important to analyze the tolerance of cells under dynamic operation conditions. This study focuses on evaluating the impact of voltage cycling on the performance and durability of electrode-supported SOECs. We explore the operational limits and degradation mechanisms of SOECs subjected to various voltage conditions and find that the cells have high tolerance for dynamic voltage. Voltage cycling between 1.3 V and 1.5 V for 9000 cycles does not damage the cell. Conversely, cycling to higher voltages (≥1.7 V) results in accelerated degradation. Advanced characterization is used to screen for various degradation modes post operation. Within the oxygen electrode, XRD and STEM EDS find compositional and phase evolution in all voltage cycled samples including increased decomposition of the air electrode resulting in cation migration. Microstructural analysis of the fuel electrode from nano-CT data shows minimal change throughout the sample set and no evidence of Ni migration, indicating the fuel electrode is stable and not impacted by cycling to higher voltages within the timeframe studied.

Zhu, Zhikuan↗

Perspectives on Low-Temperature Electrolysis and Potential for Renewable Hydrogen at Scale

Hydrogen is an important part of any discussion on sustainability and reduction in emissions across major energy sectors. In addition to being a feedstock and process gas for many industrial processes, hydrogen is emerging as a fuel alternative for transportation applications. Renewable sources of hydrogen are therefore required to increase in capacity. Low-temperature electrolysis of water is currently the most mature method for carbon-free hydrogen generation and is reaching relevant scales to impact the energy landscape. However, costs still need to be reduced to be economical with traditional hydrogen sources. Operating cost reductions are enabled by the recent availability of low-cost sources of renewable energy, and the potential exists for a large reduction in capital cost withmaterial and manufacturing optimization. This article focuses on the current status and development needs by component for the low-temperature electrolysis options.

08 HYDROGEN↗

TESTING AND PERFORMANCE ANALYSIS OF NASA 5 CM BY 5 CM BI-SUPPORTED SOLID OXIDE ELECTROLYSIS CELLS OPERATED IN BOTH FUEL CELL AND STEAM ELECTROLYSIS MODES

A series of 5 cm by 5 cm bi-supported Solid Oxide Electrolysis Cells (SOEC) were produced by NASA for the Idaho National Laboratory (INL) and tested under the INL High Temperature Steam Electrolysis program. The results from the experimental demonstration of cell operation for both hydrogen production and operation as fuel cells is presented. An overview of the cell technology, test apparatus and performance analysis is also provided. The INL High Temperature Steam Electrolysis laboratory has developed significant test infrastructure in support of single cell and stack performance analyses. An overview of the single cell test apparatus is presented. The test data presented in this paper is representative of a first batch of NASA's prototypic 5 cm by 5 cm SOEC single cells. Clearly a significant relationship between the operational current density and cell degradation rate is evident. While the performance of these cells was lower than anticipated, in-house testing at NASA Glenn has yielded significantly higher performance and lower degradation rates with subsequent production batches of cells. Current post-test microstructure analyses of the cells tested at INL will be published in a future paper. Modification to cell compositions and cell reduction techniques will be altered in the next series of cells to be delivered to INL with the aim to decrease the cell degradation rate while allowing for higher operational current densities to be sustained. Results from the testing of new batches of single cells will be presented in a future paper.

08 HYDROGEN↗

Simple Electrolyzer Model Development for High-Temperature Electrolysis System Analysis Using Solid Oxide Electrolysis Cell

An electrolyzer model for the analysis of a hydrogen-production system using a solid oxide electrolysis cell (SOEC) has been developed, and the effects for principal parameters have been estimated by sensitivity studies based on the developed model. The main parameters considered are current density, area specific resistance, temperature, pressure, and molar fraction and flow rates in the inlet and outlet. Finally, a simple model for a high-temperature hydrogen-production system using the solid oxide electrolysis cell integrated with very high temperature reactors is estimated.

99 GENERAL AND MISCELLANEOUS↗

Nanoporous Iridium Nanosheets for Polymer Electrolyte Membrane Electrolysis

The growth of the hydrogen economy is predicated on advancements in electrochemical energy technologies, with water electrolysis as a key component to the technological portfolio. Much of the focus on anode catalyst development for polymer electrolyte membrane water electrolyzers (PEMWE) is centered on activity as controlled by compositional and morphological impacts on reactant/intermediate/product adsorption. However, the effectiveness of this strategy is found to be limited upon integration of these materials into PEMWE membrane electrode assemblies (MEA). Regardless of catalyst activity, the combination of electrode inhomogeneity, ionomer integration, and high density of oxide-oxide interfaces yields significant performance losses associated with poor catalytic electrode conductivity. Here many of these limitations are addressed through the development of a unique catalyst morphology composed of nanoporous Ir nanosheets (npIr(x)-NS) that exhibit high catalytic activity for the anodic oxygen evolution reaction and superior electrode electronic conductivity in comparison to a commercial IrO2 nanoparticle catalyst. The utility of the npIr(x)-NS is demonstrated through incorporation into PEMWE MEAs where their performance exceeds that of commercial catalyst coated membranes at loadings as low as 0.06 mg(Ir) cm(-2) while exhibiting a negligible loss in performance following 50 000 accelerated stress test cycles.

Polymer Electrolyte Membrane Electrolysis↗

An all-oxide electrolysis cells for syngas production with tunable H 2 /CO yield via co-electrolysis of H 2 O and CO 2

High-rate production of syngas with tunable H 2 /CO and coke-free operation is achieved in a solid-oxide electrolysis cell (SOEC). Prior to operation, controlled pre-reduction of La 0.7 Sr 0.3 Fe 0.9 Ni 0.1 O 3-δ (LSFNi) cathode is used to trigger the in-situ exsolution of Ni-Fe alloy nanoparticles with an average size of ~45 nm uniformly distributed and socketed on LSFNi backbone, enabling efficient co-electrolysis of H 2 O and CO 2 to H 2 and CO. At 1.5 V, the current density reaches ~1.0 A cm-2 at 750 °C and ~2.4 A cm -2 at 850 °C with near 100% Faradaic Efficiency. We demonstrate the feasibility of tuning the output H 2 /CO ratio by nearly two orders of magnitude (from ~0.1 to ~7) by manipulating H 2 O/CO 2 ratio of feed gas, operating temperature, and current density. Finally, stable operation for >100 h is obtained without evidence of carbon deposition, although high current density operation leads to observable deterioration of anode/electrolyte interface due to the rapid oxygen evolution.

25 ENERGY STORAGE↗

Synergistic Coupling of Proton Conductors BaZr 0.1 Ce 0.7 Y 0.1 Yb 0.1 O 3–δ and La 2 Ce 2 O 7 to Create Chemical Stable, Interface Active Electrolyte for Steam Electrolysis Cells

For the first time, proton conductors BaZr 0.1 Ce 0.7 Y 0.1 Yb 0.1 O 3–δ (BZCYYb) and La 2 Ce 2 O 7 (LCO) are combined to create an interface active and steam-tolerant electrolyte for high-performance proton-conducting solid oxide electrolysis cells. LCO shows good chemical compatibility with BZCYYb. The readily fabricated LCO/BZCYYb bilayer electrolyte can be densified at a temperature of as low as 1300 °C versus ~1600 °C for the benchmark steam-stable BaZr 0.8 Y 0.2 O 3–δ electrolyte. With Pr 2 NiO 4+δ as the anode and Ni as the cathode catalyst, this bilayer electrolyte cell yields a current density of 975 and 300 mA/cm 2 under a 1.3 V applied potential at 700 and 600 °C, respectively. This performance is among the best of all H-SOECs equipped with a chemically stable electrolyte so far. A BZCYYb layer in the bilayer electrolyte promotes the hydrogen evolution reaction at the cathode side, resulting in a 108% improvement over the cell without this layer. The LCO layer, on the other hand, effectively protects this functional BZCYYb layer from the high concentration of steam in a practical SOEC operation condition. The cell without the LCO layer shows degradation in terms of an increased electrolyzing potential from 1.07 to 1.29 V during a constant 400 mA/cm 2 operation at 700 °C. In contrast, the bilayer electrolyte cell maintains the same electrolyzing potential of 1.13 V under the same conduction for a 102 h operation. These findings demonstrate that this synergic bilayer electrolyte design is a vital strategy to overcome the dilemma between performance and stability faced by the current benchmark Zr- or Ce-rich Ba(CeZr)O 3–δ electrolysis cells to achieve excellent performance and stability at the same time.

36 MATERIALS SCIENCE↗

Improving the performance for direct electrolysis of CO 2 in solid oxide electrolysis cells with a Sr 1.9 Fe 1.5 Mo 0.5 O 6– δ electrode via infiltration of Pr 6 O 11 nanoparticles

Direct CO 2 electrolysis using solid oxide electrolysis cells (CO 2 -SOECs) holds promise to efficiently convert carbon dioxide to carbon monoxide and oxygen. Cathodes with desirable catalytic activity and chemical stability play a critical role in the development of direct CO 2 -SOECs. Although Sr 2 Fe 1.5 Mo 0.5 O 6–δ (SFM) has exhibited promise for direct CO 2 -SOECs due to its redox stability, it suffers from insufficient activity for the CO 2 reduction reaction (CO 2 RR). Here we report interface engineering of nanosized Pr 6 O 11 on the SFM cathode obtained through infiltration to promote the CO 2 RR performance for direct CO 2 -SOECs. The effect of Pr 6 O 11 loading on the performance of the CO 2 RR is systematically investigated. At 800 °C, the current density of the Pr 6 O 11 infiltrated SFM cathode with an optimum Pr 6 O 11 loading of 14.8 wt% reaches 1.61 A cm –2 at 1.5 V, more than double that of the SFM cathode (0.76 A cm –2 ) under the same operating conditions. X-ray photoelectron spectroscopy (XPS) characterization and in situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) analysis indicate that the adsorption ability of CO 2 on the SFM cathode has been significantly improved by the formation of Pr 6 O 11 . Temperature-programmed desorption (TPD) of CO 2 measurements further manifest that a 14.8 wt% Pr 6 O 11 -SFM cathode has better CO desorption capacity. In addition, polarization resistance of the SFM cathode has significantly decreased with the addition of Pr 6 O 11 . Three-electrode measurement was used to analyze the improved electrode kinetics. Finally, these results demonstrate that the formation of Pr 6 O 11 in the SFM cathode through infiltration is a promising approach for increasing CO 2 RR activity for CO 2 -SOECs.

03 NATURAL GAS↗

Formation of carbon–nitrogen bonds in carbon monoxide electrolysis

The electroreduction of CO 2 is a promising technology for carbon utilization. Although electrolysis of CO 2 or CO 2 -derived CO can generate important industrial multicarbon feedstocks such as ethylene, ethanol, n-propanol and acetate, most efforts have been devoted to promoting C–C bond formation. Here, we demonstrate that C–N bonds can be formed through co-electrolysis of CO and NH 3 with acetamide selectivity of nearly 40% at industrially relevant reaction rates. Full-solvent quantum mechanical calculations show that acetamide forms through nucleophilic addition of NH 3 to a surface-bound ketene intermediate, a step that is in competition with OH – addition, which leads to acetate. Here, the C–N formation mechanism was successfully extended to a series of amide products through amine nucleophilic attack on the ketene intermediate. This strategy enables us to form carbon–heteroatom bonds through the electroreduction of CO, expanding the scope of products available from CO 2 reduction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Conditions for stable operation of solid oxide electrolysis cells: oxygen electrode effects

Solid oxide electrolysis cells (SOECs) convert renewable electricity to fuels with efficiency substantially higher than other electrolysis technologies. However, questions remain regarding degradation mechanisms that limit SOEC long-term stability. One of the key degradation mechanisms is oxygen electrode delamination; although prior studies have improved the understanding of this mechanism, it is still difficult to predict how degradation depends on SOEC materials and operating conditions, i.e., temperature, voltage, and current density. Here we present a study aimed at developing a quantitative understanding of oxygen electrode delamination. Experimentally, a life test study of symmetric and full cells with yttria-stabilized zirconia (YSZ) electrolytes and Gd-doped ceria (GDC) barrier layers was done with three different perovskite oxygen electrode materials. Fracture was observed at the perovskite–GDC interface above a critical current density and below a critical operating temperature. A theory is presented that combines a calculation of the effective oxygen pressure across the electrolyte with an estimation of the pressure required for fracture. Fracture is correctly predicted for a critical oxygen partial pressure of ~7200 atm and an associated electrode overpotential of ~0.2 V, occurring at the electrode/GDC interface because of the relatively low perovskite fracture toughness. As a result, damage at the GDC/YSZ interface was also observed in some cases and explained by a peak in the oxygen pressure at this interface.

30 DIRECT ENERGY CONVERSION↗

Critical Review of Platinum Group Metal-Free Materials for Water Electrolysis: Transition from the Laboratory to the Market : Earth-abundant borides and phosphides as catalysts for sustainable hydrogen production

To combat the global problem of carbon dioxide emissions, hydrogen is the desired energy vector for the transition to environmentally benign fuel cell power. Water electrolysis (WE) is the major technology for sustainable hydrogen production. Despite the use of renewable solar and wind power as sources of electricity, one of the main barriers for the widespread implementation of WE is the scarcity and high cost of platinum group metals (pgms) that are used to catalyse the cathodic hydrogen evolution reaction (HER) and the anodic oxygen evolution reaction (OER). Hence, the critical pgm-based catalysts must be replaced with more sustainable alternatives for WE technologies to become commercially viable. This critical review describes the state-of-the-art pgm-free materials used in the WE application, with a major focus on phosphides and borides. Several emerging classes of HER and OER catalysts are reviewed and detailed structure-property correlations are comprehensively summarised. The influence of the crystallographic and electronic structures, morphology and bulk and surface chemistry of the catalysts on the activity towards OER and HER is discussed.

Chemistry↗