Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ELECTRIC DISCHARGES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Experimental study of micro electrical discharge machining discharges

Micro electrical discharge machining ({mu}EDM) is an atmospheric-pressure plasma-assisted technology that uses point-to-plane discharges in liquid dielectrics to remove microscopic quantities of electrically conductive materials. In this work, an innovative {mu}EDM prototype machine was specifically designed and fabricated to produce and control single spark discharges, thus, resolving the typical limitations of (multi-discharge) commercial machines. The work analyses the type of discharge and the micro-plasma electron-density values obtained for 0.5-38 {mu}m gap sizes, 3-10 000 {mu}s pulse durations, 75-250 V low breakdown voltages, and 1-20 A discharge currents, using different combinations of metallic electrodes in oil and in water. Results allow fitting, for micro-scale and low voltages, an empirical law between the maximum gap-size for breakdown, the breakdown voltage, and the effective stress-time. The electron density n{sub e} is obtained by optical emission spectroscopy diagnostics of the H{sub {alpha}}-line Stark broadening (yielding n{sub e}{approx}10{sup 16}-10{sup 17} cm{sup -3}, i.e., ionization degrees of {approx}2 Multiplication-Sign 10{sup -5}-10{sup -4}) and by a semi-empirical resistive plasma model. The model uses the experimental values of several electrical and geometrical quantities, and of the gas pressure estimated as {approx}60 bar-2 kbar from measurements of the plasma mechanical action, obtained using a force sensor. The quantitative information of this phenomenological study can assist the optimization of this micro-fabrication technique.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Search for a ''3.5-eV isomer'' in {sup 229}Th in a hollow-cathode electric discharge

A hollow-cathode electric discharge, a well-established source in optical spectroscopy, was used to populate the ''3.5-eV isomer'' in {sup 229}Th with use of nuclear excitation by electron transition (NEET). The radiochemically purest {sup 229}Th sample was loaded into the hollow cathode in which the electric discharge excited the {sup 229}Th to atomic states some of which could be expected to lie close to the excitation energy of the sought isomer. Although there remain some uncertainties, our experiments indicate that the isomer was populated by NEET and its {alpha} decay observed after switching off the electric discharge with a corresponding isomer half-life 1 min < or approx. T{sub 1/2}{sup m} < or approx. 3 min. From the present NEET condition, the isomer appears to lie between 3 eV and 7 eV. The probability of the isomer population by NEET is discussed.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Effects of the roughness characteristics on the wire tool surface for the electrical discharge machining properties

Wire electrical discharge machining (WEDM) has been investigated to obtain the better discharge machining properties of the removal rate and the surface roughness in a few decades. Recently, it revealed that the rough tool electrodes can improve the WEDM properties for some sort of materials. In this study, the rough wire electrodes using a wet blasting method was developed and evaluated the machining performance for the insulated Si{sub 3}N{sub 4} in the WEDM processes. As the results, it could not recognize the advantage of roughness wire electrode under the high-energy condition, but it found that the electro-conductive layer thickness became thinner in comparison with those of normal wires. On the contrary, it could be obtained the better surface roughness in the low energy condition. It was supposed that the roughed wire surface generates the homogeneous dispersion discharges on the workpiece.

36 MATERIALS SCIENCE↗

2D gasdynamic simulation of the kinetics of an oxygen-iodine laser with electric-discharge generation of singlet oxygen

The kinetic processes occurring in an electric-discharge oxygen-iodine laser are analyzed with the help of a 2D (r, z) gasdynamic model taking into account transport of excited oxygen, singlet oxygen, and radicals from the electric discharge and their mixing with the iodine-containing gas. The main processes affecting the dynamics of the gas temperature and gain are revealed. The simulation results obtained using the 2D model agree well with the experimental data on the mixture gain. A subsonic oxygen-iodine laser in which singlet oxygen is generated by a 350 W transverse RF discharge excited in an oxygen flow at a pressure P = 10 Torr and the discharge tube wall is covered with mercury oxide is simulated. The simulated mixing system is optimized in terms of the flow rate and the degree of preliminary dissociation of the iodine flow. The optimal regime of continuous operation of a subsonic electric-discharge oxygen-iodine laser is found.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

How to increase the efficiency of the electrical discharge method for destruction of nonconductive solid materials

The paper deals with the relevance of using electrical discharge technology for construction works in the city. The technical capabilities of the installation for the multi-borehole electro-discharge splitting off and destruction of rocks and concrete are described. The ways to increase the efficiency of the electrical discharge method for the destruction of solids are proposed. In order to augment the discharge circuit energy, the energy storage is separated into two individual capacitor batteries. The throttle with the inductance of 28.6 μH is installed in one of the batteries, which increases the duration of the channel energy release to 400 μs and the efficiency of electrical discharge splitting off of concrete.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Synthesis of Nickel–Carbon Nanoparticles by Electrical Discharge in Liquid

Composite nickel–carbon nanoparticles were synthesized by electrical discharge in liquid. The synthesis was carried out in water and ethanol under various discharge conditions, including purging the discharge gap with argon. In water, electrical discharge was conducted between graphite and nickel electrodes. In ethanol, two nickel electrodes were used with the liquid acting as the carbon supplier. The size of the particles obtained, their composition, and the production rate depend on the type of working fluid and synthesis duration. It was also shown that the particle production rate in water is greater than in ethanol, and purging the electrode gap with argon reduces this rate two or three times.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Influence of the Distributed Phase of Gas Bubbles on a Pulsed Electrical Discharge in Water

The development of a pulsed electrical discharge in water with vapor–air microbubbles, the volume distribution of which in water is close to uniform, has been studied experimentally. The presence of volumetric microbubbles with an average diameter of ~50 μm and a bulk gas content of no more than 1% does not change the thermal mechanism of the development of the discharge in water with a conductivity of ~300 μS/cm at overvoltages of 1–1.5, the minimum breakdown voltage being ~9 kV. Under these conditions, the determining role is played by the surface bubbles, which change the observed mechanism of the discharge development. The discharge is initiated in the surface bubbles simultaneously on both electrodes. The growth of the cathode channel at a velocity of ~60 m/s leads to the closure of the 1-cm-long gap during a time of ~160 μs.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Electric-Discharge Machining of Polymer Composites

The electric-discharge machining (EDM) of VKU-29 composite is experimentally studied. The influence of the machining conditions on the lateral electrode gap (the difference between the width of the slot in the polymer composite produced by EDM and the width of the tool electrode) is determined. The electrode gap observed in the machining of VKU-29 composite is analogous to that observed in the machining of steel workpieces. It depends on the pulse energy. Comparison of graphite, copper, and composite tool electrodes shows that the best surface quality is obtained in the latter case. In EDM by a composite electrode, no traces of damage or fluffing are seen on the machined surface.

42 ENGINEERING↗

Copper-coated electrodes for electrical discharge machining of 38X2H2MA steel

The use of copper-coated aluminum electrodes in the electrical discharge machining of 38X2H2MA steel is assessed. Such electrodes prove effective. The use of coated electrodes improves the economics of electrical discharge machining by permitting the use of cheaper materials in the electrode core.

36 MATERIALS SCIENCE↗

INTERDEPENDENCE OF ELECTRIC DISCHARGE AND MAGNETOROTATIONAL INSTABILITY IN PROTOPLANETARY DISKS

We study how the magnetorotational instability (MRI) in protoplanetary disks is affected by the electric discharge caused by the electric field in the resistive magnetohydrodynamic. We performed three-dimensional shearing box simulations with various values of plasma beta and electrical breakdown models. We find that the MRI is self-sustaining in spite of the high resistivity. The instability gives rise to the large electric field that causes the electrical breakdown, and the breakdown maintains the high degree of ionization required for the instability. The condition for this self-sustained MRI is set by the balance between the energy supply from the shearing motion and the energy consumed by ohmic dissipation. We apply the condition to various disk models and study where the active, self-sustained, and dead zones of MRI are located. In the fiducial minimum-mass solar-nebula model, the newly found sustained zone occupies only a limited volume of the disk. In the late-phase gas-depleted disk models, however, the sustained zone occupies a larger volume of the disk.

79 ASTRONOMY AND ASTROPHYSICS↗

Electric-discharge high-peak-power CO{sub 2} laser

A new electric-discharge CO{sub 2} laser with a peak power of up to 45 MW and a half-height pulse duration of 50 ns is developed. The short laser pulse was formed using a generator with a semiconductor opening switch. The maximum laser radiation energy reached 6.2 J and the efficiency with respect to the stored energy was 15%. The first peak contained 70% of the energy, and the pulse duration at the base did not exceed 1 {mu}s. (lasers)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Solid-state laser-pumped high-power electric-discharge HF laser

We report the possibility of creating high-power nonchain electric-discharge HF lasers with an all-solid-state pump source. The maximum energy stored in the pump source capacitors based on solid-state FID-switches is 990 J for the open-circuit voltage of 240 kV. The pulse energy of 30 J is obtained in the hydrogen-containing SF{sub 6} mixture at the electric efficiency of the order of 3%. (lasers)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Electric-discharge VUV laser pumped by a solid-state generator

A 193-nm electric-discharge ArF laser pumped by an all-solid-state generator based on a semiconductor switch and a system of magnetic compression of high-voltage pulses is studied. The laser emits 18-ns, 15 mJ pulses at a pulse repetition rate of 1 kHz. (lasers)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Electric Discharge Sintering and Joining of Tungsten Carbide--Cobalt Composite with High-Speed Steel Substrate

Simultaneous electro discharge sintering of high strength structure of tungsten carbide-cobalt composite and connection it with high-speed steel substrate is investigated and suitable operating parameters are defined. Tungsten carbide-cobalt and high-speed steel joining was produced by the method of high voltage electrical discharge together with application of mechanical pressure to powder compact. It was found that the density and hardness of composite material reach its maximum values at certain magnitudes of applied pressure and high voltage electrical discharge parameters. We show that there is an upper level for the discharge voltage beyond which the powder of composite material disintegrates like an exploding wire. Due to our results it is possible to determine optimal parameters for simultaneous electro discharge sintering of WC-Co and bonding it with high-speed steel substrate.

36 MATERIALS SCIENCE↗

Possibility of nonexistence of hot and superhot hydrogen atoms in electrical discharges

Recently, the existence of extremely energetic hydrogen atoms in electrical discharges has been proposed in the literature with large controversy, from the analysis of the anomalous broadening of hydrogen Balmer lines. In this paper, the velocity distribution of H atoms and the profiles of the emitting atom lines created by the exothermic reaction H{sub 2}{sup +}+H{sub 2}{yields}H{sub 3}{sup +}+H+{Delta}E are calculated, as a function of the internal energy defect {Delta}E. The shapes found for the non-Maxwell-Boltzmann distributions resulting in non-Gaussian line profiles raise serious arguments against the existence of hot and superhot H atoms as it has been proposed, at least with those temperatures.

74 ATOMIC AND MOLECULAR PHYSICS↗

More Efficient Electric-Discharge Machining of 38Х2Н2МА Steel

On the basis of experimental data, recommendations are made regarding the electric-discharge machining (EDM) of 38Х2Н2МА alloy-steel parts with improved high-temperature wear resistance. Those recommendations ensure high quality of the machined surface with the highest possible productivity. In the finishing pass, to ensure roughness R{sub a} = 2.4, the following parameters are chosen: voltage U = 100 V; time of pulse action T = 150 µs; and current I = 6 A.

36 MATERIALS SCIENCE↗