Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “EFFECT OF COMPRESSIBILITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2000

Sweep and Compressibility Effects on Active Separation Control at High Reynolds Numbers

This paper explores the effects of compressibility, sweep and excitation location on active separation control at high Reynolds numbers. The model, which was tested in a cryogenic pressurized wind tunnel, simulates the upper surface of a 20% thick GlauertGoldschmied type airfoil at zero angle of attack. The flow is fully turbulent since the tunnel sidewall boundary layer flows over the model. Without control, the flow separates at the highly convex area and a large turbulent separation bubble is formed. Periodic excitation is applied to gradually eliminate the separation bubble. Two alternative blowing slot locations as well as the effect of compressibility, sweep and steady suction or blowing were studied. During the test the Reynolds numbers ranged from 2 to 40 million and Mach numbers ranged from 0.2 to 0.7. Sweep angles were 0 and 30 deg. It was found that excitation must be introduced slightly upstream of the separation region regardless of the sweep angle at low Mach number. Introduction of excitation upstream of the shock wave is more effective than at its foot. Compressibility reduces the ability of steady mass transfer and periodic excitation to control the separation bubble but excitation has an effect on the integral parameters, which is similar to that observed in low Mach numbers. The conventional swept flow scaling is valid for fully and even partially attached flow, but different scaling is required for the separated 3D flow. The effectiveness of the active control is not reduced by sweep. Detailed flow field dynamics are described in the accompanying paper.

Seifert, Avi↗
NASA NTRS2000

Sweep and Compressibility Effects on Active Separation Control at High Reynolds Numbers

This paper explores the effects of compressibility, sweep and excitation location on active separation control at high Reynolds numbers. The model, which was tested in a cryogenic pressurized wind tunnel, simulates the upper surface of a 20% thick Glauert Goldschmied type airfoil at zero angle of attack. The flow is fully turbulent since the tunnel sidewall boundary layer flows over the model. Without control, the flow separates at the highly convex area and a large turbulent separation bubble is formed. Periodic excitation is applied to gradually eliminate the separation bubble. Two alternative blowing slot locations as well as the effect of compressibility, sweep and steady suction or blowing were studied. During the test the Reynolds numbers ranged from 2 to 40 million and Mach numbers ranged from 0.2 to 0.7. Sweep angles were 0 and 30 deg. It was found that excitation must be introduced slightly upstream of the separation region regardless of the sweep angle at low Mach number. Introduction of excitation upstream of the shock wave is more effective than at its foot. Compressibility reduces the ability of steady mass transfer and periodic excitation to control the separation bubble but excitation has an effect on the integral parameters, which is similar to that observed in low Mach numbers. The conventional swept flow scaling is valid for fully and even partially attached flow, but different scaling is required for the separated 3D flow. The effectiveness of the active control is not reduced by sweep. Detailed flow field dynamics are described in the accompanying paper.

Seifert, Avi↗
NASA NTRS1991

A study of compressibility effects on dynamic stall of rapidly pitching airfoils

Results of recent experimental studies into the effect of compressibility on dynamic stall of oscillating airfoils are reviewed. Stroboscopic schlieren images of the strongly unsteady flow field are presented, showing the development of the dynamic stall vortex, and its progression down the airfoil. The effect of varying free-stream Mach number and frequency of oscillation of the airfoil are demonstrated, and examples of local supersonic flow are presented, including the presence of a shock near the leading edge of the airfoil.

Carr, Lawrence W.↗
NASA NTRS1990

Schlieren studies of compressibility effects on dynamic stall of airfoils in transient pitching motion

Compressibility effects on the flowfield of an airfoil executing rapid transient pitching motion from 0 - 60 degrees over a wide range of Mach numbers and pitching rates were studied using a stroboscopic schlieren flow visualization technique. The studies have led to the first direct experimental documentation of multiple shocks on the airfoil upper surface flow for certain conditions. Also, at low Mach numbers, additional coherent vortical structures were found to be present along with the dynamic stall vortex, whereas at higher Mach numbers, the flow was dominated by a single vortex. The delineating Mach number for significant compressibility effects was 0.3 and the dynamic stall process was accelerated by increasing the Mach number above that value. Increasing the pitch rate monotonically delayed stall to angles of attack as large as 27 degrees.

Chandrasekhara, M. S.↗
NASA NTRS1993

Compressibility Effects on the Growth and Structure of Homogeneous Turbulent Shear Flow

Compressibility effects within decaying isotropic turbulence and homogeneous turbulent shear flow have been studied using direct numerical simulation. The objective of this work is to increase our understanding of compressible turbulence and to aid the development of turbulence models for compressible flows. The numerical simulations of compressible isotropic turbulence show that compressibility effects are highly dependent on the initial conditions. The shear flow simulations, on the other hand, show that measures of compressibility evolve to become independent of their initial values and are parameterized by the root mean square Mach number. The growth rate of the turbulence in compressible homogeneous shear flow is reduced compared to that in the incompressible case. The reduced growth rate is the result of an increase in the dissipation rate and energy transfer to internal energy by the pressure-dilatation correlation. Examination of the structure of compressible homogeneous shear flow reveals the presence of eddy shocklets, which are important for the increased dissipation rate of compressible turbulence.

Blaisdell, G. A.↗
NASA NTRS1992

Unsteady blade pressures on a propfan - Predicted and measured compressibility effects

The effect of compressibility on unsteady blade pressures is studied by solving the 3D Euler equations. The operation of the eight-bladed SR7L propfan at 4.75 deg angle of attack was considered. Euler solutions were obtained for three Mach numbers, 0.6, 0.7, and 0.8 and the predicted blade pressure waveforms were compared with flight data. In general, the effect of Mach number on pressure waveforms are correctly predicted. The change in pressure waveforms are minimal when the Mach number is increased from 0.6 to 0.7. Increasing the Mach number from 0.7 to 0.8 produces significant changes in predicted pressure levels. The predicted amplitudes, however, differ from measurements at some transducer locations. Also the predicted appearance of a shock in the highly loaded portion of the blade revolution is not indicated by the measurements. At all the three Mach numbers, the measured (installed propfan) pressure waveforms show a relative phase lag compared to the computed (propfan alone) waveforms due to installation effects. Measured waveforms in the blade tip region show nonlinear variations which are not captured by the present numerical procedure.

Nallasamy, M.↗
NASA NTRS1992

Unsteady blade pressures on a propfan: Predicted and measured compressibility effects

The effect of compressibility on unsteady blade pressures is studied by solving the three-dimensional Euler equations. The operation of the eight-bladed SR7L propfan at a 4.75 deg angle of attack was considered. Euler solutions were obtained for three Mach numbers, 0.6, 0.7 and 0.8, and the predicted blade pressure waveforms were compared with flight data. The comparisons show that in general, the effect of Mach number on pressure waveforms are correctly predicted. The change in pressure waveforms are minimal when the Mach number is increased from 0.6 to 0.7. Increasing the Mach number from 0.7 to 0.8 produces significant changes in predicted pressure levels. The predicted amplitudes, however, differ from measurements at some transducer locations. At all the three Mach numbers, the measured (installed propfan) pressure waveforms show a relative phase lag compared to the computed (propfan along) waveforms due to installation effects. Measured waveforms in the blade tip region show nonlinear variations which are not captured by the present numerical procedure.

Nallasamy, M.↗
NASA NTRS1988

Compressibility effects on flow friction in a fully developed pipe flow

A method was evolved to account for the effects of compressibility in flows through long circular pipes of uniform diameter. Velocity and density variations across the flow cross section were approximated by profile shapes recommended for a flow past flat plates. The wall of the pipe was assumed to have attained an adiabatic condition. An integral method was used to obtain solutions for the governing equations of flow. The method was then used to analyze the detailed pressure measurements made in a long pipe for flow of air at different flow rate settings. Flow friction values derived from these pressure measurements were compared with the standard incompressible pipe flow data available in existing literature.

Murthy, Sreedhara V.↗
NASA NTRS2005

Investigation of Compressibility Effect for Aeropropulsive Shear Flows

Rocket Based Combined Cycle (RBCC) engines operate within a wide range of Mach numbers and altitudes. Fundamental fluid dynamic mechanisms involve complex choking, mass entrainment, stream mixing and wall interactions. The Propulsion Research Center at the University of Alabama in Huntsville is involved in an on- going experimental and numerical modeling study of non-axisymmetric ejector-based combined cycle propulsion systems. This paper attempts to address the modeling issues related to mixing, shear layer/wall interaction in a supersonic Strutjet/ejector flow field. Reynolds Averaged Navier-Stokes (RANS) solutions incorporating turbulence models are sought and compared to experimental measurements to characterize detailed flow dynamics. The effect of compressibility on fluids mixing and wall interactions were investigated using an existing CFD methodology. The compressibility correction to conventional incompressible two- equation models is found to be necessary for the supersonic mixing aspect of the ejector flows based on 2-D simulation results. 3-D strut-base flows involving flow separations were also investigated.

Balasubramanyam, M. S.↗
NASA NTRS1999

Computational Analysis of Compressibility Effects on a High-Lift Wing

The objective of this study was to investigate compressibility effects on a high-lift flowfield by simulating the flow about a three-dimensional multi-element wing. The computations were performed by solving both the incompressible and compressible Navier-Stokes equations (using the INS3D and OVERFLOW codes) on structured, overset grids. Turbulence was modeled via the one-equation, fully turbulent Spalart-Allmaras model. The computational results were validated with surface pressure measurements acquired at the NASA Ames 7- by 10-Foot Wind Tunnel. The geometry used for all computations consisted of an unswept wing in a landing configuration with a half-span flap and a three-quarter-span slat mounted inside a rectangular duct approximating the wind tunnel walls. The solutions were carefully examined to account for effects due to differences in algorithms. Compressibility effects were demonstrated by comparing surface particle traces, sectional pressure coefficient and boundary layer profile plots. It was found that small regions of compressibility near the slat and main-element leading edge can largely impact the flow. Even small compressibility regions can have significant global effects on the circulation and separation of each of the high-lift elements.

Baker, M. David↗
NASA NTRS1941

Compressibility Effects in Aeronautical Engineering

Compressible-flow research, while a relatively new field in aeronautics, is very old, dating back almost to the development of the first firearm. Over the last hundred years, researches have been conducted in the ballistics field, but these results have been of practically no use in aeronautical engineering because the phenomena that have been studied have been the more or less steady supersonic condition of flow. Some work that has been done in connection with steam turbines, particularly nozzle studies, has been of value, In general, however, understanding of compressible-flow phenomena has been very incomplete and permitted no real basis for the solution of aeronautical engineering problems in which.the flow is likely to be unsteady because regions of both subsonic and supersonic speeds may occur. In the early phases of the development of the airplane, speeds were so low that the effects of compressibility could be justifiably ignored. During the last war and immediately after, however, propellers exhibited losses in efficiency as the tip speeds approached the speed of sound, and the first experiments of an aeronautical nature were therefore conducted with propellers. Results of these experiments indicated serious losses of efficiency, but aeronautical engineers were not seriously concerned at the time became it was generally possible. to design propellers with quite low tip. speeds. With the development of new engines having increased power and rotational speeds, however, the problems became of increasing importance.

Stack, John↗
NASA NTRS1991

Fluid Compressibility Effects on the Dynamic Response of Hydrostatic Journal Bearings

A theoretical analysis for the dynamic performance characteristics of laminar flow, capillar/orifice compensated hydrostatic journal bearings is presented. The analysis considers in detail the effect of fluid compressibility in the bearing recesses. At high frequency excitations beyond a break frequency, the bearing hydrostatic stiffness increases sharply and it is accompanied by a rapid decrease in direct damping. Also, the potential of pneumatic hammer instability (negative damping) at low frequencies is likely to occur in hydrostatic bearing applications handling highly compressible fluids. Useful design criteria to avoid undesirable dynamic operating conditions at low and high frequencies are determined. The effect of fluid recess compressibility is brought into perspective, and found to be of utmost importance on the entire frequency spectrum response and stability characteristics of hydrostatic/hybrid journal bearings.

Sanandres, Luis A.↗
NASA NTRS1994

Compressibility Effects on the Passive Scalar Flux Within Homogeneous Turbulence

Compressibility effects on turbulent transport of a passive scalar are studied within homogeneous turbulence using a kinematic decomposition of the velocity field into solenoidal and dilatational parts. It is found that the dilatational velocity does not produce a passive scalar flux, and that all of the passive scalar flux is due to the solenoidal velocity.

Blaisdell, G. A.↗
NASA NTRS2004

Modeling Compressibility Effects in High-Speed Turbulent Flows

Man has strived to make objects fly faster, first from subsonic to supersonic and then to hypersonic speeds. Spacecraft and high-speed missiles routinely fly at hypersonic Mach numbers, M greater than 5. In defense applications, aircraft reach hypersonic speeds at high altitude and so may civilian aircraft in the future. Hypersonic flight, while presenting opportunities, has formidable challenges that have spurred vigorous research and development, mainly by NASA and the Air Force in the USA. Although NASP, the premier hypersonic concept of the eighties and early nineties, did not lead to flight demonstration, much basic research and technology development was possible. There is renewed interest in supersonic and hypersonic flight with the HyTech program of the Air Force and the Hyper-X program at NASA being examples of current thrusts in the field. At high-subsonic to supersonic speeds, fluid compressibility becomes increasingly important in the turbulent boundary layers and shear layers associated with the flow around aerospace vehicles. Changes in thermodynamic variables: density, temperature and pressure, interact strongly with the underlying vortical, turbulent flow. The ensuing changes to the flow may be qualitative such as shocks which have no incompressible counterpart, or quantitative such as the reduction of skin friction with Mach number, large heat transfer rates due to viscous heating, and the dramatic reduction of fuel/oxidant mixing at high convective Mach number. The peculiarities of compressible turbulence, so-called compressibility effects, have been reviewed by Fernholz and Finley. Predictions of aerodynamic performance in high-speed applications require accurate computational modeling of these "compressibility effects" on turbulence. During the course of the project we have made fundamental advances in modeling the pressure-strain correlation and developed a code to evaluate alternate turbulence models in the compressible shear layer.

Sarkar, S.↗
NASA NTRS1991

Compressibility effects on the growth and structure of homogeneous turbulent shear flow

Direct numerical simulations of compressible homogeneous turbulent shear flow are used to provide insight into compressibility effects on turbulence. The simulations show a reduction in the growth rate of the turbulence compared to the incompressible case. Examination of the turbulent kinetic energy budget shows that the reduced growth rate is due to an increase in the dissipation rate due to the divergence of the velocity and to the pressure-dilatation correlation which acts to transfer energy between internal energy and kinetic energy. The structure of the turbulence is also examined. Visualizations of the flowfields reveal the presence of eddy shocklets. These shock structures are important contributors to the increased dissipation of compressible turbulence. A mechanism for the generation of the shocks is suggested.

Blaisdell, G. A.↗
NASA NTRS1974

Compressibility effects in the Kemp-Sears Problem

The effects of including compressibility in the Kemp-Sears problem of aerodynamic interference between moving blade rows are examined. Methods of linearized, subsonic, plane, unsteady flow are adopted. The major new effect is that a resonance appears at certain combinations of flow Mach number, tip Mach number, and blade vane ratios. The resonance is at exactly the Tyler-Sofrin cutoff condition for rotor-stator interaction. At such conditions the unsteady lift on a blade row due to externally imposed nonstationary upwash vanishes. However, the resonance appears to be very sharp and seems to be more significant as an indication that around this condition the unsteady lift changes very rapidly.

Mani, R.↗
NASA NTRS1992

Compressibility effects on large structures in free shear flows

Space-time correlations were used to study compressibility effects on large structures in mixing layers. Two high-Reynolds number mixing layers with M(c) = 0.51 (case 1) and 0.86 (case 2) were studied. The results indicate that the structures in case 1 are similar to those in the incompressible case, but less organized. The structures in case 2 are highly three-dimensional, with a good spatial but a poor temporal orgnization. The streamwise correlations showed a decay rate four to five times greater for case 2 relative to case 1. While the spanwise correlations for case 1 showed trends similar to incompressible mixing layers, the behavior of case 2 was very different. The pressure fluctuations in the fully developed region of case 2 displayed significant rms variation in the spanwise direction with a well-defined pattern. Based on these measurements, the structures in case 2 seem to be of a horseshoe type, transversely spanning the mixing layer with the head in the low-speed side and the legs inclined in both the x-y and the x-z planes.

Samimy, M.↗