Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Doping”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Pyrolyzer Assisted Vapor Transport Deposition of Antimony-Doped Cadmium Telluride

In this study, we developed a new method for in situ Sb doping of CdTe thin films combining vapor transport deposition with a Group V pyrolyzer to address Sb doping concentration and doping efficiency. The Sb doped CdSeTe (CdSeTe:Sb) films were deposited in solar cell structures under variations of Sb dopant source heater, vapor pyrolyzer temperature, and Cd vapor excess. Results indicate that although these parameters do not affect the CdTe morphology or crystal structure, they critically influence doping efficiency and trap concentration. Capacitance-voltage measurements show that a higher dopant heater (TD) or pyrolyzer (TP) temperature leads to higher net carrier concentration, achieving a net carrier concentration of 1016 cm-3 and 20% doping efficiency with a TD/TP combination of 600 degrees C/1100 degrees C. By tuning the Cd/Sb flux ratio during CdSeTe:Sb deposition, the lowest defect concentration is achieved at Cd/Sb of 1.4:1, which produced the best VOC CdSeTe:Sb cell. This demonstrates a path to produce high net carrier concentration polycrystalline CdTe thin film with a low concentration of dopant-induced defects.

14 SOLAR ENERGY↗
NASA NTRS1996

Effect of variations in the doping profiles on the properties of doped multiple quantum well avalanche photodiodes

The purpose of this study is to use both theoretical and experimental evidence to determine the impact of doping imbalance and symmetry on the physical and electrical characteristics of doped multiple quantum well avalanche photodiodes (APD). Theoretical models have been developed to calculate the electric field valence and conduction bands, capacitance-voltage (CV), and carrier concentration versus depletion depth profiles. The models showed a strong correlation between the p- and n-doping balance inside the GaAs wells and the number of depleted stages and breakdown voltage of the APD. A periodic doping imbalance in the wells has been shown to result in a gradual increase (or decrease) in the electric field profile throughout the device which gave rise to partially depleted devices at low bias. The MQW APD structures that we modeled consisted of a 1 micron top p(+)-doped (3 x 10(exp 18) cm(exp -3)) GaAs layer followed by a 1 micron region of alternating layers of GaAs (500 A) and Al(0.42)Ga(0.58)As (500 A), and a 1 micron n(+) back layer (3 x 10(exp 18) cm(exp -3)). The GaAs wells were doped with p-i-n layers placed at the center of each well. The simulation results showed that in an APD with nine doped wells, and where the 50 A p-doped layer is off by 10% (p = 1.65 x 10(exp 18) cm(exp -3), n = 1.5 x 10(exp 18) cm(exp -3)), almost half of the MQW stages were shown to be undepleted at low bias which was a result of a reduction in the electric field near the p(+) cap layer by over 50% from its value in the balanced structure. Experimental CV and IV data on similar MBE grown MQW structures have shown very similar depletion and breakdown characteristics. The models have enabled us to better interpret our experimental data and to determine both the extent of the doping imbalances in the devices as well as the overall p- or n-type doping characteristics of the structures.

Menkara, H. M.↗
DOE OSTI2025

High gain and wideband hybrid optical amplifier using bismuth-doped and neodymium-doped fibers for E-band applications

A hybrid dual-stage bismuth-doped fiber and neodymium-doped fiber amplifier with high optical gain and extended bandwidth of operation in the E-band is demonstrated. The amplifier features a maximum gain of 43 dB, output power of 372 mW, and a minimum noise figure of 5.5 dB, and operation wavelength range of 1397–1472 nm, enabled by 153-m of bismuth-doped fiber and two 7-m lengths of neodymium-doped fiber. The demonstration shows the possibility of achieving improved gain bandwidth by combining fiber amplifiers with overlapping gain spectra in the E-band.

Applied optics↗
DOE OSTI2025

Doping topological Dirac semimetal with magnetic impurities: Electronic structure of Mn-doped Cd 3 ⁢As 2

The prospect of transforming a Dirac topological semimetal (TSM) into a Weyl TSM phase, following doping by magnetic impurities, is central to TSM applications. The magnetic field from polarized 𝑑 levels of magnetic impurities produces a field with a sharp local structure. To what extent magnetic impurities act in the same manner as an applied field and what are the effects of such a field on the electronic structure of a Dirac TSM are the subject of this paper. We present electronic structure calculations of bulk Cd 3 ⁢As 2 with substitutional doping of Mn impurities in the dilute alloy range. Quasiparticle 𝐺⁡𝑊 (QS⁢𝐺⁡𝑊) ab initio electronic structure calculations are used in conjunction with 𝑘 · 𝑝 model Hamiltonian calculations. As expected, we observe the splitting of the Dirac points into pairs of Weyl points following the doping with Mn. We also show that the electronic structure of Mn-doped Cd 3⁢ As 2 can be emulated by the electronic structure of pristine Cd 3⁢ As 2 with an appropriate external magnetic field. Some properties of the conductivity of bulk Cd 3 ⁢As 2 for different magnetic field orientations are also investigated. Our results inform future opportunities for unique device functionality based on band structure tuning not found in conventional magnetic Weyl TSM.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Sb doping via drive-in diffusion as an alternative to in-situ doping in VTD

Group-V doping can enhance the efficiency of CdTe photovoltaic devices by increasing the open-circuit voltage (Voc), if long lifetimes can be retained and radiative voltage loss can be avoided. In this preliminary study, ex-situ Sb doping via drive-in diffusion improved grain sizes compared to Sb-free films without CdCl2 treatment. Sb doping did not reduce the carrier lifetime for uniform CdSeTe absorbers. Additionally, the CST-air surface recombination decreased with Sb. No potential fluctuations were observed by PL at this doping level. The [Sb] and carrier concentration for this study are not yet measured so the conclusions drawn are all preliminary

14 SOLAR ENERGY↗
DOE OSTI2025

Fabrication of nanoporous doped metal oxide coatings via selective infiltration of a block copolymer template: The case of Al-doped zinc oxide

Conductive nanoporous conformal coatings are important for various applications including touchscreens, displays, and electrochromic windows, though design of such coating with controlled porosity and composition remains challenging. We propose a sequential infiltration synthesis (SIS) method for the fabrication of nanoporous conductive aluminum-doped zinc oxide (AZO) films by infiltrating block copolymer (BCP) templates, specifically polystyrene-block-polyvinyl pyridine (PS-b-P4VP), with diethyl zinc and trimethyl aluminum precursors. Tunability of both porosity and electrical conductivity is achieved by precisely controlling the swelling behavior of the polymer templates and adjusting the number of SIS cycles. Further, our results reveal that porosity levels can reach up to 80 %, with resistivity as low as ~7.83 Ωcm. Using conductive atomic force microscopy (C-AFM) and Hall effect measurements, we show that lower concentrations of aluminum doping relative to zinc (around 1: 17) results in higher conductivity of the AZO films. Additionally, AZO is based on zinc oxide (ZnO) which is cost-efficient, abundant and less toxic than commonly used transparent conductive oxides such as indium tin oxide (ITO) and fluorine-doped tin oxide (FTO). Therefore, this novel approach opens new possibilities for creating highly porous, conformal, conductive AZO coatings with customizable porosity and composition, making them ideal candidates for diverse optoelectronic applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Doping Dependence of 2-Spinon Excitations in the Doped 1D Cuprate Ba 2 ⁢CuO 3+δ

Recent photoemission experiments on the quasi-one-dimensional Ba-based cuprates suggest that doped holes experience an attractive potential not captured using the simple Hubbard model. This observation has garnered significant attention due to its potential relevance to Cooper pair formation in high-T c cuprate superconductors. To scrutinize this assertion, we examined signatures of such an attractive potential in doped 1D cuprates Ba 2 ⁢CuO 3+δ by measuring the dispersion of the 2-spinon excitations using Cu L 3 -edge resonant inelastic x-ray scattering (RIXS). Upon doping, the 2-spinon excitations appear to weaken, with a shift of the minimal position corresponding to the nesting vector of the Fermi points, q F . Notably, we find that the energy scale of the 2-spinons near the Brillouin zone boundary is substantially softened compared to that predicted by the Hubbard model in one dimension. Finally, such a discrepancy implies missing ingredients, which lends support for the presence of an additional attractive potential between holes.

1-dimensional spin chains↗
DOE OSTI2024

Characterization of n-Type Iodine-Doped and Indium-Doped CdTe/Cd-Se-Te Thin Films Fabricated by Close-Spaced Sublimation Epitaxy

In this study, n-type CdTe thin films, specifically iodine-doped CdTe (CdTe:I), indium-doped CdTe (CdTe:In), and indium-doped Cd-Se-Te (CST:In), were synthesized using close-spaced sublimation epitaxy (CSSE). Characterization techniques secondary ion mass spectrometry (SIMS), electron backscatter diffraction (EBSD), Hall-effect measurements, and time-resolved photoluminescence (TRPL) were employed to analyze the chemical, structural, and electronic properties of these materials. The results indicated epitaxial single crystal CSSE films grew on the single crystal substrates, with carrier density ranging from 10^14 - 10^16 cm -3 , and after post-annealing, the minority-carrier lifetimes reach near the radiative limit. Additionally, a preliminary exploration of homojunction structures with an n- type (CdTe:In /CST:In /CdTe:I) /CdTe:P /Cu /Mo configuration was performed. The best device performance was achieved with CdTe:I including CdS aiding in band alignment, resulting in a power conversion efficiency (..eta..) of 2.61% with open circuit voltage (Voc) of 850 mV, fill factor (FF) of 47.8%, and short-circuit current (Jsc) of 6.44 mA/cm 2 . The observed low Jsc and efficiency may be attributed to a buried junction and a poor interface, due to dopant interdiffusion. Consequently, further investigations focusing on interface optimization, diffusion blocking, and reduced recombination through passivation, are crucial to enhancing the efficiency of CSSE CdTe homojunction devices in the future.

cadmium compounds↗
DOE OSTI2026

Luminescence properties of europium doped and sodium co-doped LiCaAlF 6

This paper serves as a literature review of scintillating thermal neutron detectors, along with a study of sodium and europium doped LiCaAlF 6 (LiCAF) polycrystalline material. A set of polycrystalline LiCAF material was synthesized with 2 molar percent of europium (Eu 2+ ) and co-doped with 0, 1, and 2 molar percent of sodium (Na + ), with a stoichiometric synthesis approach in a glassy-carbon crucible. The quantum yield and photoluminescence spectrum at room temperature was analyzed. For the first time, we have demonstrated that Na-co-doping directly alters the quantum yield. The quantum yield for LiCAF:Eu 2+ , with 0, 1, and 2 molar percent of sodium (Na + ) was 0.578, 0.635, and 0.580, respectively. The photoluminescence (PL) spectrum was also analyzed for all samples. The photo-luminescence excitation (PLE) spectrum showed a maximum at 300 nm, while the emission spectrum showed a maximum at 370 nm, corresponding to the Eu 2+ 5d-4f transitions.

36 MATERIALS SCIENCE↗
NASA NTRS1919

Airplane dopes and doping

Cellulose acetate and cellulose nitrate are the important constituents of airplane dopes in use at the present time, but planes were treated with other materials in the experimental stages of flying. The above compounds belong to the class of colloids and are of value because they produce a shrinking action on the fabric when drying out of solution, rendering it drum tight. Other colloids possessing the same property have been proposed and tried. In the first stages of the development of dope, however, shrinkage was not considered. The fabric was treated merely to render it waterproof. The first airplanes constructed were covered with cotton fabric stretched as tightly as possible over the winds, fuselage, etc., and flying was possible only in fine weather. The necessity of an airplane which would fly under all weather conditions at once became apparent. Then followed experiments with rubberized fabrics, fabrics treated with glue rendered insoluble by formaldehyde or bichromate, fabrics treated with drying and nondrying oils, shellac, casein, etc. It was found that fabrics treated as above lost their tension in damp weather, and the oil from the motor penetrated the proofing material and weakened the fabric. For the most part the film of material lacked durability. Cellulose nitrate lacquers, however were found to be more satisfactory under varying weather conditions, added less weight to the planes, and were easily applied. On the other hand, they were highly inflammable, and oil from the motor penetrated the film of cellulose nitrate, causing the tension of the fabric to be relaxed.

PROTECTIVE COATINGS AND COVERINGS↗
DOE OSTI2025

Facet-Dependent Doping and Dopant-Dependent Faceting in Si-Doped GaAsSb Nanowires

Here, we correlate the spatial distributions of Si, Sb, and rotational twins in Si-doped GaAs 1-x Sb x nanowires. GaAs 1-x Sb x nanowires were grown epitaxially on Si(111) substrates by tuning process conditions to achieve repeated nucleation of rotational twins and growth along the [111]B direction; dilute Sb and Si fluxes were chosen to create a sufficient twin density to achieve high yield while avoiding growth of the wurtzite phase. While the impact of Si and Sb on twin density and nanowire growth rate has been previously reported, the facet-dependent incorporation of these species has not been established. Scanning transmission electron microscopy was used to confirm that Sb incorporates preferentially on the (111)B facets relative to {1 ̅1 ̅0} facets prior to nucleation of a rotational twin. With periodic twinning, this facet dependence leads to alternating regions of enriched and depleted Sb concentration attributed to a growth rate-dependent Sb-As-exchange mechanism. Atom probe tomography measurements establish that while Si doping is not perturbed by twinning on (111)B facets, Si and Sb concentrations are anti-correlated for growth on non-(111)B facets. Density functional theory calculations underpin a thermodynamic model that explains the observed anisotropies in dopant incorporation.

36 MATERIALS SCIENCE↗
NASA NTRS1981

Lattice defects in semiconducting Hg/1-x/Cd/x/Te alloys. I - Defect structure of undoped and copper doped Hg/0.8/Cd/0.2/Te. II - Defect structure of indium-doped Hg/0.8/Cd/0.2/Te

Hall effect and mobility measurements were conducted on undoped Hg(0.8)Cd(0.2)Te crystals which were quenched to room temperature after being subjected to equilibration at temperatures ranging from 400 to 655 C in various Hg atmospheres. The variation of the hole concentration in the cooled crystals at 77 K as a function of Hg's partial pressure at the equilibration temperature, together with a comparison of the hole mobility in the undoped samples with that in copper-doped ones, yields a defect model for the undoped crystals according to which they are intrinsic at the equilibration temperatures and the native acceptor defects are doubly ionized. In the second part of this paper, the effects of indium doping are considered. The concentration of electrons obtained in the cooled crystals was found to be lower than the intrinsic carrier concentration at the equilibration temperatures. A defect model is proposed according to which most of the indium is incorporated as In2Te3(s) dissolved in the crystal, with only a small fraction of indium acting as single donors occupying Hg lattice sites.

Vydyanath, H. R.↗
NASA NTRS1984

Engineering and design properties of thallium-doped sodium iodide and selected properties of sodium-doped cesium iodide

Mechanical and thermal properties, not available in the literature but necessary to structural design, using thallium doped sodium iodide and sodium doped cesium iodide were determined to be coefficient of linear thermal expansion, thermal conductivity, thermal shock resistance, heat capacity, elastic constants, ultimate strengths, creep, hardness, susceptibility to subcritical crack growth, and ingot variation of strength. These properties were measured for single and polycrystalline materials at room temperature.

Forrest, K.↗
NASA NTRS1989

An empirical study of the performance of APMOVPE AM0 InP homojunction solar cells as a function of emitter thickness and doping, and base doping

Their excellent radiation resistance and conversion efficiencies greater than 20 percent, measured under global conditions, make InP shallow-homojunction solar cells very attractive for space or terrestrial application. In addition, modeling studies show that, for optimized design, efficiencies of these devices should exceed 20 percent even under AM0 conditions. However, a systematic experimental investigation of the influence of the various cell design parameters on cell performance has not as yet been made. For the n+/p/p+ structures investigated in the previous modeling study, the design parameters include the impurity concentrations and thicknesses of the emitter and base layers. In the work reported here, researchers discuss an experimental investigation of the effects on cell performance of varying the impurity concentrations of the emitter and base and thickness of the emitter.

Wanlass, M. W.↗