Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DUCTILITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Prospects for Ductility and Toughness Enhancement of Nial by Ductile Phase Reinforcement

The use of NiAl as a structural material has been hindered by the fact that this ordered intermetallic does not exhibit significant tensile ductility or toughness at room temperature. A critical review of the operative flow and fracture mechanisms in monolithic NiAl has thus established the need for ductile phase toughening in this order system. Progress in ductile phase reinforced intermetallic systems in general and specifically NiAl-based materials has been reviewed. In addition, further clarification of the primary mechanisms involved in the flow and fracture of ductile phase reinforced alloys has evolved from ongoing investigations of several model NiAl-based materials. The mechanical behavior of these model directionally-solidified alloys (Ni-30Al and Ni-30Fe-20Al) are discussed. Finally, the prospects for developing a ductile phase toughened NiAl-based alloy and the shortcomings presently inherent in these systems are analyzed.

Noebe, R. D.↗
NASA NTRS1960

An Exploratory Investigation of Some Factors Influencing the Room-Temperature Ductility of Tungsten

Specimens having an initial diameter of 0.125 inch were cut from commercially pure sintered and swaged tungsten rods. The effect of various surface treatments on the ductility of tungsten was evaluated by the use of a bend test. The criterion used to determine the relative ductilities was the final bend angle of the specimens. Results showed that the bend ductility of the tungsten specimens increased with increasing depths of the surface removed by electropolishing. When specimens electropolished to a depth sufficient to produce a marked increase in the ductility over that of the as-received surface condition were subsequently scratched with emery paper, the ductility achieved by electropolishing was greatly reduced. Removal of similar depths of the surface by grinding as were removed by electropolishing did not produce any appreciable increase in the ductility of the specimens. The ductility of specimens tested in the as-received surface condition and those having an electropolished surface exhibited a great sensitivity to deflection rate, the electropolished specimens being more ductile over the range of deflection rates tested. These exploratory results illustrated qualitatively the importance of surface condition on the room-temperature ductility of tungsten and indicated the importance of relatively fine scratches on the ductility of tungsten.

Stephens, Joseph R.↗
NASA NTRS1983

Microstructural evolution in the HAZ of Inconel 718 and correlation with the hot ductility test

The nickel-base alloy 718 was evaluated to study the role of preweld heat treatment in reducing or eliminating heat-affected zone hot cracking. Three heat treatments were studied using the Gleeble hot ductility test. A modified hot ductility test was also used to follow the evolution of microstructure during simulated welding thermal cycles. The microstructural evolution was correlated with the hot ductility data in order to evaluate the mechanism of hot cracking in alloy 718. The correlation of hot ductility with microstructure showed that recrystallization, grain growth, and dissolution of precipitates did not in themselves cause any loss of ductility during cooling. Ductility loss during cooling was not initiated until the constitutional liquation of NbC particles was observed in the microstructure. Laves-type phases were found precipitated in the solidified grain boundaries but were not found to correlate with any ductility loss parameter. Mechanisms are reviewed which help to explain how heat treatment controls the hot crack susceptibility of alloy 718 as measured in the hot ductility test.

Thompson, R. G.↗
NASA NTRS1982

The strength and ductility of polycrystalline NiAl in tension

Experiments at temperatures from 20 C to 400 C at two strain rates (.0001/s and .000005/s) establish that: (1) at room temperatures, binary and microalloyed ( 1000 ppm La, Y, Mo, Ti) NiAl shows negligible ductility, independent of grain size over the range 5 to 140 micrometers; (2) at 295 C the tensile elongation of binary 51 Ni/49 Al increases from 1% to about 5% upon decreasing the grain size to below approximately 10 micrometers; (3) similarly, at 400 C the ductility increases from about 2% to 15% upon decreasing the grain size to below 15 micrometers; (4) the ductility of fine grained (7 micrometer) binary aggregates deformed at 295 C increases from approximately 5% to 12% upon decreasing the strain rate from .0001/s to .000005/s; (5) partial recrystallization (10% to 20%) of warm extruded binary and microalloyed material imparts 1% to 2% ductility at room temperature where fully recrystallized material is brittle; (6) the yield strength obeys a Hall-Petch relationship; and (7) when ductility is not observed, fracture coincides with yielding. The mechanisms underlying the flow and fracture of NiAl are discussed in terms of the nucleation and growth of microcracks. The concept of a critical grain size is considered in the light of the results.

Schulson, E. M.↗
NASA NTRS1990

Influence of testing environment on the room temperature ductility of FeAl alloys

The effects of testing atmospheres (air, O2, N2, and vacuum) on the room-temperature ductility of Fe-40Al, Fe-40Al-0.5B, and Fe-50Al alloys were investigated. The results confirmed the decrease in room-temperature ductility of Fe-rich FeAl alloys by the interaction of the aluminide with water vapor, reported previously by Liu et al. (1989). The highest ductilities were measured in the atmosphere with the lowest moisture levels, i.e., in vacuum. It was found that significant ductility is still restricted to Fe-rich alloys (Fe-40Al), as the Fe-50Al alloy remained brittle under all testing conditions. It was also found that slow cooling after annealing was beneficial, and the effect was additive to the environmental effect. The highest ductility measurements in this study were 9 percent elongation in furnace-cooled Fe-40Al and in Fe-40Al-0.5B, when tested in vacuum.

Gaydosh, D. J.↗
NASA NTRS1992

Deformation mechanisms of NiAl cyclicly deformed near the brittle-to-ductile transformation temperature

One of the ongoing challenges of the aerospace industry is to develop more efficient turbine engines. Greater efficiency entails reduced specific strength and larger temperature gradients, the latter of which means higher operating temperatures and increased thermal conductivity. Continued development of nickel-based superalloys has provided steady increases in engine efficiency and the limits of superalloys have probably not been realized. However, other material systems are under intense investigation for possible use in high temperature engines. Ceramic, intermetallic, and various composite systems are being explored in an effort to exploit the much higher melting temperatures of these systems. NiAl is considered a potential alternative to conventional superalloys due to its excellent oxidation resistance, low density, and high melting temperature. The fact that NiAl is the most common coating for current superalloy turbine blades is a tribute to its oxidation resistance. Its density is one-third that of typical superalloys and in most temperature ranges its thermal conductivity is twice that of common superalloys. Despite these many advantages, NiAl requires more investigation before it is ready to be used in engines. Binary NiAl in general has poor high-temperature strength and low-temperature ductility. On-going research in alloy design continues to make improvements in the high-temperature strength of NiAl. The factors controlling low temperature ductility have been identified in the last few years. Small, but reproducible ductility can now be achieved at room temperature through careful control of chemical purity and processing. But the mechanisms controlling the transition from brittle to ductile behavior are not fully understood. Research in the area of fatigue deformation can aid the development of the NiAl system in two ways. Fatigue properties must be documented and optimized before NiAl can be applied to engineering systems. More importantly though, probing the deformation mechanisms operating in fatigue will lead to a better understanding of NiAl's unique characteristics. Low cycle fatigue properties have been reported on binary NiAl in the past year, yet those studies were limited to two temperature ranges: room temperature and near 1000 K. Eventually, fatigue property data will be needed for a wide range of temperatures and compositions. The intermediate temperature range near the brittle-to-ductile transition was chosen for this study to ascertain whether the sharp change occurring in monotonic behavior also occurs under cyclic conditions. An effort was made to characterize the dislocation structures which evolved during fatigue testing and comment on their role in the deformation process.

Antolovich, Stephen D.↗
NASA NTRS1991

Ductility of a continuous fiber reinforced aluminum matrix composite

The transverse properties of an aluminum alloy metal matrix composite reinforced by continuous alumina fibers have been investigated. The composite is subjected to both mechanical and cyclic thermal loading. The ductility can vary by an order of magnitude according to the operating conditions. For high mechanical and low thermal loading the ductility is small, for low mechanical and high thermal loading the ductility is an order of magnitude higher. Experiments on a beam in bending confirm that the ductility is strongly dependent on the loading conditions. The observations suggest a means of utilizing the inherent ductility of the matrix.

Jansson, S.↗
NASA NTRS2024

Influence of Ductility on the Performance of Lunar Habitat Structures Under Recurrent Disturbances

This research examines how ductility affects the durability of lunar surface structures against recurring disturbances like moonquakes, micrometeorite impacts, and thermal cycles over an extended period. The structural performance at various levels of ductility was determined by adjusting material parameters and the thickness of a reference multilayered dome structure. Moonquake and micrometeorite impact-induced lateral displacements were estimated using a reduced-order model under a control-oriented dynamic computational modeling framework. The study considered the degradation of the metallic dome’s strength properties over time due to thermal cycles. Fragility curves were generated by assessing the likelihood of reaching three predefined damage levels as a result of multiple hazards. Additionally, a discounted cash flow analysis was conducted to incorporate a financial aspect into the performance comparison. The findings revealed that structures with sufficient ductility capacity have a lower probability of sustaining severe damage or collapsing within a shorter time frame. Hence, having ductile structures in lunar environments is advantageous as it allows the postponement of maintenance and repair actions, thereby conserving scarce resources for more urgent tasks. Moreover, the financial analysis demonstrated that lunar habitats with higher ductile capacities result in larger net present values, offering a higher return on the initial investment.

Arsalan Majlesi↗
NASA NTRS2021

Investigation of Ionic Liquids Isolated Iron for Ductile Iron Castings

As research continues for missions beyond low-Earth orbit, in-situ resource utilization (ISRU) methods are critical. For Lunar and Martian colonization, the ability to manufacture mechanical and structural components with local resources is essential. Ionic liquids (IL) are being studied at NASA Marshall Space Flight Center (MSFC) to harvest elemental metals from meteorites and regolith oxides. In this investigation, the viability of casting ductile iron using ionic liquids sourced iron and nickel was explored given ductile iron’s range of applications and performance as an as-cast alloy. Ingots were produced using commercial elements to simulate the use of IL iron with carbon sourced from the by-products of a life support system currently tested at MSFC. Samples were cast and compared to commercial ductile iron with phase transformation diagrams,microstructures, and hardness. Results showed ionic liquids sourced elements are a viable source of elemental alloying materials for a range of ductile iron alloys.

Ionic Liquids↗
NASA NTRS1983

A brittle to ductile transition in NiAl of a critical grain size

Tensile tests have been carried out on the strongly ordered B2 aluminide NiAl at 400 C to investigate the effect of the grain size on the ductility of the material. It is found that the ductility is very low and essentially independent of the grain size for aggregates of grains larger than about 20 microns; for finer-grained aggregates, the ductility increases sharply with decreasing grain size. Thus, NiAl exhibits a critical grain size below which polycrystalline aggregates are ductile in tension. For all grain sizes, fracture occurs in a brittle manner through a combination of intergranular decohesion and transgranular cleavage.

Schulson, E. M.↗
NASA NTRS1987

Room temperature tensile ductility in powder processed B2 FeAl alloys

It has been shown that it is possible to obtain significant room temperature tensile ductility in FeAl alloys using iron-rich deviations from stoichiometry. A comparison of the room temperature tensile and compressive behaviors of Fe-50 at. pct Al and Fe-40 at. pct Al shows that FeAl is brittle at higher Al contents because it fractures along grain boundaries before general yielding. Lower aluminum contents reduce the yield stress substantially and hence some ductility is observed before fracture. Addition of boron results in measurable improvements in ductility of Fe-40 at. pct Al and is accompanied by an increase in transgranular tearing on the fracture surface, suggesting a grain boundary strengthening mechanism. Increasing the cooling rate following annealing at 1273 K results in a large increase in the yield strength and a corresponding decrease in ductility.

Crimp, M. A.↗
NASA NTRS1989

Ductile-regime turning of germanium and silicon

Single-point diamond turning of silicon and germanium was investigated in order to clarify the role of cutting depth in coaxing a ductile chip formation in normally brittle substances. Experiments based on the rapid withdrawal of the tool from the workpiece have shown that microfracture damage is a function of the effective depth of cut (as opposed to the nominal cutting depth). In essence, damage created by the leading edge of the tool is removed several revolutions later by lower sections of the tool edge, where the effective cutting depth is less. It appears that a truly ductile cutting response can be achieved only when the effective cutting depth, or critical chip thickness, is less than about 20 nm. Factors such as tool rake angle are significant in that they will affect the actual value of the critical chip thickness for transition from brittle to ductile response. It is concluded that the critical chip thickness is an excellent parameter for measuring the effects of machining conditions on the ductility of the cut and for designing tool-workpiece geometry in both turning and grinding.

Blake, Peter N.↗
NASA NTRS1989

Improving the low temperature ductility of NiAl

As part of a study aimed at developing a ductile NiAl-based alloy, ingots of Ni-Fe-Al alloys were cast and hot extruded to rods. The purpose of the iron additions was two-fold viz; to produce a change in the slip vector from 001 to 111 line and, in one alloy, to add a L1(2)-structured ductile second phase. Extruded Ni-20Al-30Fe was two-phase, containing a pro-eutectic B2 phase in a fine lamellar structure of B2+L1(2) phases. Room temperature tensile testing of both single extruded and double extruded alloys resulted in 8-percent and 22-percent plastic elongation and yield stresses of 850 and 760 MPa, respectively. Fracture in both cases occurred by ductile tearing of the eutectic and transgranular cleavage of the proeutectic phase at 1350 MPa. The ductility in double extruded condition is higher than that reported earlier in rapidly solidified wires by Inoue et al. (1984). By comparison, extruded single-phase B2-structured Ni-30Al-20Fe exhibited a fracture strength of 780 MPa, no plasticity, and a mixture of intergranular fracture and transgranular cleavage. This is contrast to earlier work by Inoue et al. where a yield stress of 400 MPa, 5 percent plastic strain, and a mixture of dimple and intergranular fracture was reported.

Guha, Sumit↗
NASA NTRS1991

Flow and fracture behavior of NiAl in relation to the brittle-to-ductile transition temperature

NiAl has only three independent slip systems operating at low and intermediate temperatures whereas five independent deformation mechanisms are required to satisfy the von Mises criterion for general plasticity in polycrystalline materials. Yet, it is generally recognized that polycrystalline NiAl can be deformed extensively in compression at room temperature and that limited tensile ductility can be obtained in extruded materials. In order to determine whether these results are in conflict with the von Mises criterion, tension and compression tests were conducted on powder-extruded, binary NiAl between 300 and 1300 K. The results indicate that below the brittle-to-ductile transition temperature (BDTT) the failure mechanism in NiAl involves the initiation and propagation of cracks at the grain boundaries which is consistent with the von Mises analysis. Furthermore, evaluation of the flow behavior of NiAl indicates that the transition from brittle to ductile behavior with increasing temperature coincides with the onset of recovery mechanisms such as dislocation climb. The increase in ductility above the BDTT is therefore attributed to the climb of the 001 line type dislocations which in combination with dislocation glide enable grain boundary compatibility to be maintained at the higher temperatures.

Noebe, R. D.↗
NASA NTRSDate not supplied

Investigation of Ionic Liquids Isolated Iron for Ductile Iron Castings

As research continues for missions beyond low-Earth orbit, in-situ resource utilization (ISRU) methods are critical. To colonize the Lunar or Martian surface, the ability to manufacture mechanical and structural components with local resources is essential. Ionic liquids are being studied at NASA Marshall Space Flight Center (MSFC) to harvest elemental metals from meteorites and oxides in regolith. In this investigation, the viability of casting ductile iron using ionic liquids sourced iron and nickel was explored given ductile iron’s range of applications and performance as an as-cast alloy. Small ingots were produced using commercial silicon, manganese, and magnesium with carbon sourced from the by-products of a life support system currently being tested at MSFC. Samples were cast and compared to commercial ductile iron with phase transformation diagrams, microstructures, and hardness. Results showed ionic liquids sourced elements are a viable source of elemental alloying materials for a range of ductile iron alloys.

Blake Stewart↗
NASA NTRS1972

Ductile-brittle transition of thoriated chromium.

Unalloyed chromium and chromium containing approximately 3 wt % ThO2 were prepared from powder produced by a chemical vapor deposition process. When rolled to sheet and tested in tension, it was found that the thoriated material had a lower ductile-to-brittle transition temperature (DBTT) than unalloyed chromium. This ductilizing was evident both in the as-rolled condition and after the materials had been annealed for 1 hour at 1200 C. The improved ductility in thoriated chromium may be associated with several possible mechanisms: (1) particles may disperse slip, such that critical stress or strain concentrations for crack nucleation are more difficult to achieve; (2) particles may act as dislocation sources, thus providing mobile dislocations in this normally source-poor material, in a manner similar to prestraining; and (3) particles in grain boundaries may help to transmit slip across the boundaries, thus relieving stress concentrations and inhibiting crack nucleation.

Wilcox, B. A.↗