Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DOPES & DOPING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Pyrolyzer Assisted Vapor Transport Deposition of Antimony-Doped Cadmium Telluride

In this study, we developed a new method for in situ Sb doping of CdTe thin films combining vapor transport deposition with a Group V pyrolyzer to address Sb doping concentration and doping efficiency. The Sb doped CdSeTe (CdSeTe:Sb) films were deposited in solar cell structures under variations of Sb dopant source heater, vapor pyrolyzer temperature, and Cd vapor excess. Results indicate that although these parameters do not affect the CdTe morphology or crystal structure, they critically influence doping efficiency and trap concentration. Capacitance-voltage measurements show that a higher dopant heater (TD) or pyrolyzer (TP) temperature leads to higher net carrier concentration, achieving a net carrier concentration of 1016 cm-3 and 20% doping efficiency with a TD/TP combination of 600 degrees C/1100 degrees C. By tuning the Cd/Sb flux ratio during CdSeTe:Sb deposition, the lowest defect concentration is achieved at Cd/Sb of 1.4:1, which produced the best VOC CdSeTe:Sb cell. This demonstrates a path to produce high net carrier concentration polycrystalline CdTe thin film with a low concentration of dopant-induced defects.

14 SOLAR ENERGY↗
DOE OSTI2025

High gain and wideband hybrid optical amplifier using bismuth-doped and neodymium-doped fibers for E-band applications

A hybrid dual-stage bismuth-doped fiber and neodymium-doped fiber amplifier with high optical gain and extended bandwidth of operation in the E-band is demonstrated. The amplifier features a maximum gain of 43 dB, output power of 372 mW, and a minimum noise figure of 5.5 dB, and operation wavelength range of 1397–1472 nm, enabled by 153-m of bismuth-doped fiber and two 7-m lengths of neodymium-doped fiber. The demonstration shows the possibility of achieving improved gain bandwidth by combining fiber amplifiers with overlapping gain spectra in the E-band.

Applied optics↗
DOE OSTI2025

Doping topological Dirac semimetal with magnetic impurities: Electronic structure of Mn-doped Cd 3 ⁢As 2

The prospect of transforming a Dirac topological semimetal (TSM) into a Weyl TSM phase, following doping by magnetic impurities, is central to TSM applications. The magnetic field from polarized 𝑑 levels of magnetic impurities produces a field with a sharp local structure. To what extent magnetic impurities act in the same manner as an applied field and what are the effects of such a field on the electronic structure of a Dirac TSM are the subject of this paper. We present electronic structure calculations of bulk Cd 3 ⁢As 2 with substitutional doping of Mn impurities in the dilute alloy range. Quasiparticle 𝐺⁡𝑊 (QS⁢𝐺⁡𝑊) ab initio electronic structure calculations are used in conjunction with 𝑘 · 𝑝 model Hamiltonian calculations. As expected, we observe the splitting of the Dirac points into pairs of Weyl points following the doping with Mn. We also show that the electronic structure of Mn-doped Cd 3⁢ As 2 can be emulated by the electronic structure of pristine Cd 3⁢ As 2 with an appropriate external magnetic field. Some properties of the conductivity of bulk Cd 3 ⁢As 2 for different magnetic field orientations are also investigated. Our results inform future opportunities for unique device functionality based on band structure tuning not found in conventional magnetic Weyl TSM.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Sb doping via drive-in diffusion as an alternative to in-situ doping in VTD

Group-V doping can enhance the efficiency of CdTe photovoltaic devices by increasing the open-circuit voltage (Voc), if long lifetimes can be retained and radiative voltage loss can be avoided. In this preliminary study, ex-situ Sb doping via drive-in diffusion improved grain sizes compared to Sb-free films without CdCl2 treatment. Sb doping did not reduce the carrier lifetime for uniform CdSeTe absorbers. Additionally, the CST-air surface recombination decreased with Sb. No potential fluctuations were observed by PL at this doping level. The [Sb] and carrier concentration for this study are not yet measured so the conclusions drawn are all preliminary

14 SOLAR ENERGY↗
DOE OSTI2025

Fabrication of nanoporous doped metal oxide coatings via selective infiltration of a block copolymer template: The case of Al-doped zinc oxide

Conductive nanoporous conformal coatings are important for various applications including touchscreens, displays, and electrochromic windows, though design of such coating with controlled porosity and composition remains challenging. We propose a sequential infiltration synthesis (SIS) method for the fabrication of nanoporous conductive aluminum-doped zinc oxide (AZO) films by infiltrating block copolymer (BCP) templates, specifically polystyrene-block-polyvinyl pyridine (PS-b-P4VP), with diethyl zinc and trimethyl aluminum precursors. Tunability of both porosity and electrical conductivity is achieved by precisely controlling the swelling behavior of the polymer templates and adjusting the number of SIS cycles. Further, our results reveal that porosity levels can reach up to 80 %, with resistivity as low as ~7.83 Ωcm. Using conductive atomic force microscopy (C-AFM) and Hall effect measurements, we show that lower concentrations of aluminum doping relative to zinc (around 1: 17) results in higher conductivity of the AZO films. Additionally, AZO is based on zinc oxide (ZnO) which is cost-efficient, abundant and less toxic than commonly used transparent conductive oxides such as indium tin oxide (ITO) and fluorine-doped tin oxide (FTO). Therefore, this novel approach opens new possibilities for creating highly porous, conformal, conductive AZO coatings with customizable porosity and composition, making them ideal candidates for diverse optoelectronic applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Doping Dependence of 2-Spinon Excitations in the Doped 1D Cuprate Ba 2 ⁢CuO 3+δ

Recent photoemission experiments on the quasi-one-dimensional Ba-based cuprates suggest that doped holes experience an attractive potential not captured using the simple Hubbard model. This observation has garnered significant attention due to its potential relevance to Cooper pair formation in high-T c cuprate superconductors. To scrutinize this assertion, we examined signatures of such an attractive potential in doped 1D cuprates Ba 2 ⁢CuO 3+δ by measuring the dispersion of the 2-spinon excitations using Cu L 3 -edge resonant inelastic x-ray scattering (RIXS). Upon doping, the 2-spinon excitations appear to weaken, with a shift of the minimal position corresponding to the nesting vector of the Fermi points, q F . Notably, we find that the energy scale of the 2-spinons near the Brillouin zone boundary is substantially softened compared to that predicted by the Hubbard model in one dimension. Finally, such a discrepancy implies missing ingredients, which lends support for the presence of an additional attractive potential between holes.

1-dimensional spin chains↗
DOE OSTI2024

Characterization of n-Type Iodine-Doped and Indium-Doped CdTe/Cd-Se-Te Thin Films Fabricated by Close-Spaced Sublimation Epitaxy

In this study, n-type CdTe thin films, specifically iodine-doped CdTe (CdTe:I), indium-doped CdTe (CdTe:In), and indium-doped Cd-Se-Te (CST:In), were synthesized using close-spaced sublimation epitaxy (CSSE). Characterization techniques secondary ion mass spectrometry (SIMS), electron backscatter diffraction (EBSD), Hall-effect measurements, and time-resolved photoluminescence (TRPL) were employed to analyze the chemical, structural, and electronic properties of these materials. The results indicated epitaxial single crystal CSSE films grew on the single crystal substrates, with carrier density ranging from 10^14 - 10^16 cm -3 , and after post-annealing, the minority-carrier lifetimes reach near the radiative limit. Additionally, a preliminary exploration of homojunction structures with an n- type (CdTe:In /CST:In /CdTe:I) /CdTe:P /Cu /Mo configuration was performed. The best device performance was achieved with CdTe:I including CdS aiding in band alignment, resulting in a power conversion efficiency (..eta..) of 2.61% with open circuit voltage (Voc) of 850 mV, fill factor (FF) of 47.8%, and short-circuit current (Jsc) of 6.44 mA/cm 2 . The observed low Jsc and efficiency may be attributed to a buried junction and a poor interface, due to dopant interdiffusion. Consequently, further investigations focusing on interface optimization, diffusion blocking, and reduced recombination through passivation, are crucial to enhancing the efficiency of CSSE CdTe homojunction devices in the future.

cadmium compounds↗
DOE OSTI2026

Luminescence properties of europium doped and sodium co-doped LiCaAlF 6

This paper serves as a literature review of scintillating thermal neutron detectors, along with a study of sodium and europium doped LiCaAlF 6 (LiCAF) polycrystalline material. A set of polycrystalline LiCAF material was synthesized with 2 molar percent of europium (Eu 2+ ) and co-doped with 0, 1, and 2 molar percent of sodium (Na + ), with a stoichiometric synthesis approach in a glassy-carbon crucible. The quantum yield and photoluminescence spectrum at room temperature was analyzed. For the first time, we have demonstrated that Na-co-doping directly alters the quantum yield. The quantum yield for LiCAF:Eu 2+ , with 0, 1, and 2 molar percent of sodium (Na + ) was 0.578, 0.635, and 0.580, respectively. The photoluminescence (PL) spectrum was also analyzed for all samples. The photo-luminescence excitation (PLE) spectrum showed a maximum at 300 nm, while the emission spectrum showed a maximum at 370 nm, corresponding to the Eu 2+ 5d-4f transitions.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Facet-Dependent Doping and Dopant-Dependent Faceting in Si-Doped GaAsSb Nanowires

Here, we correlate the spatial distributions of Si, Sb, and rotational twins in Si-doped GaAs 1-x Sb x nanowires. GaAs 1-x Sb x nanowires were grown epitaxially on Si(111) substrates by tuning process conditions to achieve repeated nucleation of rotational twins and growth along the [111]B direction; dilute Sb and Si fluxes were chosen to create a sufficient twin density to achieve high yield while avoiding growth of the wurtzite phase. While the impact of Si and Sb on twin density and nanowire growth rate has been previously reported, the facet-dependent incorporation of these species has not been established. Scanning transmission electron microscopy was used to confirm that Sb incorporates preferentially on the (111)B facets relative to {1 ̅1 ̅0} facets prior to nucleation of a rotational twin. With periodic twinning, this facet dependence leads to alternating regions of enriched and depleted Sb concentration attributed to a growth rate-dependent Sb-As-exchange mechanism. Atom probe tomography measurements establish that while Si doping is not perturbed by twinning on (111)B facets, Si and Sb concentrations are anti-correlated for growth on non-(111)B facets. Density functional theory calculations underpin a thermodynamic model that explains the observed anisotropies in dopant incorporation.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Doping in Efficient Polycrystalline CdSeTe Solar Cells via AsCl 3 Vapor Annealing

Doping in cadmium telluride (CdTe) thin-film solar cells is a critical step in producing highly efficient CdTe solar modules. To date, copper (Cu) ex-situ diffusion doping and group V in situ doping (such as arsenic, As) have been effectively used in manufacturing CdTe solar modules. However, Cu doping is prone to rapid degradation, whereas the low activation ratio of the dopants constrains group V in situ doping. Recently, ex-situ group V doping has been developed, showing an improved doping activation ratio through a solution process. Here, in this study, we developed a vapor-based AsCl 3 doping method for diffusion doping of polycrystalline CdSeTe devices. AsCl 3 vapor annealing can promote the diffusion of As into the bulk CdSeTe through a surface chemical reaction between CdTe and AsCl 3 . This approach has led to a long carrier lifetime of over 72 ns, V oc of 850 mV, and power conversion efficiency of ~18% with Au metal electrodes. The vapor-based ex situ group V doping approach offers an effective means to perform group V diffusion doping into the CdSeTe device.

14 SOLAR ENERGY↗
DOE OSTI2025

Ab initio prediction of FeCr sigma (001)/FCC Fe(111) interfacial energy: Effect of interfacial doping of C, B, and N

Interfacial energy plays a crucial role for high-temperature material systems in determining their microstructure evolution and mechanical properties. Optimizing the interfacial energy through doping can improve the stability, performance, and overall functionality of these materials. Here, the present study delivers theoretical investigation on the sigma FeCr (001)//FCC Fe (111) interfacial energy using ab initio methods, focusing on the implications of interfacial doping with important interstitial elements carbon (C), boron (B), and nitrogen (N). The calculated interfacial energy without doping is 0.183J/m 2 . Upon doping, notable reductions in interfacial energy were observed. Doping with B decreased the interfacial energy to 0.046J/m 2 , with single C doping to 0.126J/m 2 , with two C doping to 0.098J/m 2 , and with a single N doping to 0.071J/m 2 . These findings not only shed light on the atomistic origin for the effect of stabilizing the microstructure of stainless steel at elevated temperatures by interstitial doping, but also present a systematic, thorough ab initio approach to predict interfacial doping properties and guide alloy design to enhance the performance and stability.

FeCr sigma phase↗
DOE OSTI2025

Resistivity distribution and donor properties of antimony-doped n -type Czochralski silicon ingots

We investigate antimony (Sb)-doped Czochralski-grown silicon as an alternative n-type substrate for photovoltaic applications, and characterize their axial resistivity distribution, donor properties, and mechanical strength. We find that Sb-doped ingots can achieve a more uniform resistivity distribution along the axial direction compared to P-doped counterparts. Dopant concentration profiles in P-doped ingots can be accurately modelled using the standard Scheil's equation, accounting only for dopant segregation during solidification. In contrast, modelling Sb-doped ingots requires consideration of both dopant segregation and evaporation effects to fit the dopant distribution accurately. Using electron paramagnetic resonance spectroscopy at 9 K, we observe two hyperfine lines in P-doped samples, and six hyperfine lines for Sb 121 and eight for Sb 123 isotopes, with the number of hyperfine lines governed by the nuclear spins. We further identify two-atom Sb clustering in the Sb-doped wafers, confirmed through simulations of the additional weak electron paramagnetic resonance peaks. Finally, we find that 140 μm as-cut planar Sb-doped wafers exhibit slightly higher mechanical strength compared to P-doped wafers.

14 SOLAR ENERGY↗
DOE OSTI2025

Heavy boron doping effects on biaxially tensile strained germanium (>1.5%) investigated via structural characterization, effective lifetime assessment and atomistic modeling

Highly tensile strained germanium (ε-Ge) represents an essential material system for emerging electronic and photonics applications. Moreover, adjusting the doping levels to moderate or high concentrations can effectively tailor the properties of ε-Ge for specific applications. This article combines experimental characterization with a theoretical framework to examine the effects of heavy elemental boron (B) doping on pseudomorphic sub-50 nm ε-Ge. High resolution X-ray diffractometry is used to validate tensile strain levels of 1.53% and 1.68% in Ge epilayers, surpassing the indirect-to-direct band gap crossover point at ∼1.5% biaxial tensile strain. Cross-sectional transmission electron microscopy revealed visual evidence of stacking faults and surface roughening in 1.68% ε-Ge, although a coherent and abrupt Ge/III–V heterointerface is observed, devoid of interfacial misfit dislocations. Effective lifetime measurements demonstrated approximately twofold enhancement in 1.53% B-doped ε-Ge (N B ∼7 × 10 19 cm −3 ) compared to its unstrained B-doped counterpart, while no such improvement was observed in 1.68% B-doped ε-Ge. This lack of enhancement is attributed to the presence of stacking faults and surface roughness within the ε-Ge epilayer. Through density functional theory calculations, we independently demonstrate that substitutional B atoms induce local deformation of Ge–Ge bonds in both unstrained Ge and ε-Ge epilayers, resulting in an additive tensile strain. This phenomenon could potentially lead to dynamic reduction and overcoming of the critical layer thickness for the system, facilitating the nucleation and subsequent glide of 90° leading Shockley partial dislocations, thereby generating stacking faults. In essence, these findings establish an upper limit on the B-doping concentration that can be achieved in highly ε-Ge epilayers, and collectively, offer valuable insights into the significance of heavy doping in Ge-based heterostructures. As such, this study delineates a fundamental constraint for integrating heavily doped ε-Ge in high-performance optoelectronic systems, necessitating precise strain-doping co-optimization to avoid performance degradation.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2024

Impacts of point defects on shallow doping in cubic boron arsenide: A first principles study

Cubic boron arsenide (BAs) stands out as a promising material for advanced electronics, thanks to its exceptional thermal conductivity and ambipolar mobility. However, effective control of p- and n-type doping in BAs poses a significant challenge, mostly as a result of the influence of defects. In the present study, we employed density functional theory (DFT) to explore the impacts of the common point defects and impurities on p-type doping of Be B and Si As , and on n-type doping of Si B and Se As . We found that the most favorable point defects formed by C, O, and Si are C As , O B O As , Si As , C As Si B , and O B Si As , which have formation energies of less than 1.5 eV. While the O impurity detrimentally affects both p- and n-type dopings, C and Si impurities are harmful for n-type dopings, making n-type doping a potential challenge. Interestingly, the antisite defect pair A s B B As benefits both p- and n-type doping. Finally, the doping limitation analysis presented in this study can potentially pave the way for strategic development in the area of BAs-based electronics.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Spatially Enhanced Electrostatic Doping in Graphene Realized via Heterointerfacial Precipitated Metals

Forming heavily-doped regions in 2D materials, like graphene, is a steppingstone to the design of emergent devices and heterostructures. Here, a selective-area approach is presented to tune the work-function and carrier density in monolayer graphene by spatially synthesizing sub-monolayer gallium beneath the 2D-solid. The localized metallic gallium is formed via precipitation from an underlying diamond-like carbon (DLC) film that is spatially implanted with gallium-ions. By controlling the interfacial precipitation process with annealing temperature, spatially precise ambipolar tuning of the graphene work-function is achieved, and the tunning effect preserved upon cooling to ambient conditions. Consequently, charge carrier densities from ≈1.8 × 10 10 cm -2 (hole-doped) to ≈7 × 10 13 cm -2 (electron-doped) are realized, confirmed by in situ and ex situ measurements. The theoretical studies corroborated the role of gallium at the heterointerface on charge transfer and electrostatic doping of the graphene overlayer. Specifically, sub-monolayer gallium facilitates heavy n-doping in graphene. Extending this doping strategy to other implantable elements in DLC provides a new means of exploring the physics and chemistry of highly-doped 2D materials.

36 MATERIALS SCIENCE↗