Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DIE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

The thermal fatigue resistance of H-13 Die Steel for aluminum die casting dies

The effects of welding, five selected surface coatings, and stress relieving on the thermal fatigue resistance of H-13 Die Steel for aluminum die casting dies were studied using eleven thermal fatigue specimens. Stress relieving was conducted after each 5,000 cycle interval at 1050 F for three hours. Four thermal fatigue specimens were welded with H-13 or maraging steel welding rods at ambient and elevated temperatures and subsequently, subjected to different post-weld heat treatments. Crack patterns were examined at 5,000, 10,000, and 15,000 cycles. The thermal fatigue resistance is expressed by two crack parameters which are the average maximum crack and the average cracked area. The results indicate that a significant improvement in thermal fatigue resistance over the control was obtained from the stress-relieving treatment. Small improvements were obtained from the H-13 welded specimens and from a salt bath nitrogen and carbon-surface treatment. The other surface treatments and welded specimens either did not affect or had a detrimental influence on the thermal fatigue properties of the H-13 die steel.

Source record↗
NASA NTRS1981

Sputtered protective coatings for die casting dies

This investigation determined whether selected ion beam sputtered coatings on H-13 die steel would have the potential of improving the thermal fatigue behavior of the steel used as a die in aluminum die casting. The coatings were selected to test candidate insulators and metals capable of providing protection of the die surface. The studies indicate that 1 micrometer thick W and Pt coatings reduced the thermal fatigue more than any other coating tested and are candidates to be used on a die surface to increase die life.

Mirtich, M. J.↗
NASA NTRS1981

Sputtered protective coatings for die casting dies

Three experimental research designs investigating candidate materials and processes involved in protective die surface coating procedures by sputter deposition, using ion beam technologies, are discussed. Various pre-test results show that none of the coatings remained completely intact for 15,000 test cycles. The longest lifetime was observed for coatings such as tungsten, platinum, and molybdenum which reduced thermal fatigue, but exhibited oxidation and suppressed crack initiation only as long as the coating did not fracture. Final test results confirmed earlier findings and coatings with Pt and W proved to be the candidate materials to be used on a die surface to increase die life. In the W-coated specimens, which remained intact on the surface after thermal fatigue testing, no oxidation was found under the coating, although a few cracks formed on the surface where the coating broke down. Further research is planned.

Mirtich, M. J.↗
NASA NTRS1981

Thermal fatigue behavior of H-13 die steel for aluminum die casting with various ion sputtered coatings

Sputtered coatings of Mo, W, Pt, Ag, Au, Co, Cr, Ni, Ag + Cu, Mo + Pt, Si3N4, A1N, Cr3C2, Ta5Si3, and ZrO2 were applied to a 2-inch-square, 7-inch-long thermal fatigue test specimen which was then internally water cooled and alternately immersed in molten aluminum and cooled in air. After 15,000 cycles the thermal fatigue cracks at the specimen corners were measured. Results indicate that a significant improvement in thermal fatigue resistance was obtained with platinum, molybdenum, and tungsten coatings. Metallographic examination indicates that the improvement in thermal fatigue resistance resulted from protection of the surface of the die steel from oxidation. The high yield strength and ductility of molybdenum and tungsten contributed to the better thermal fatigue resistance.

Nieh, C. Y.↗
DOE OSTI2024

Modifikation eines Cu‐Pd‐Schaufelrad‐Metall‐Organischen Gerüsts für die selektive CO 2 ‐Elektroreduktion

Abstract Die Optimierung der Bindungsenergie zwischen dem Intermediat und dem aktiven Zentrum ist ein entscheidender Faktor, um die katalytische Produktselektivität und Aktivität bei der elektrochemischen Kohlendioxidreduktion (CO 2 RR) zu steuern. Es ist bekannt, dass Kupferatome als aktive Zentren CO 2 zu Kohlenwasserstoffen und Sauerstoffverbindungen reduzieren, jedoch unter schlechter Produktselektivität leiden, da mehrere Intermediate nur moderate Bindungsenergien aufweisen. Hier berichten wir über eine Ionenaustauschstrategie zur Konstruktion von Cu−Pd‐Schaufelrad‐Dimeren innerhalb von Cu‐basierten metallorganischen Gerüsten (MOFs), [Cu 3‐x Pdx(BTC) 2 ] (BTC=1,3,5‐Benzoltricarbonsäure), ohne die strukturellen Eigenschaften des MOFs zu verändern. Im Vergleich zum reinen Cu‐MOF ([Cu 3 (BTC) 2 ], HKUST‐1) verlagert der Cu−Pd‐MOF die Produkte der CO 2 ‐Elektroreduktion von einer Vielzahl chemischer Spezies hin zu einer selektiven CO‐Erzeugung. Eine in situ‐Röntgenabsorptions‐Feinstrukturanalyse der Oxidationsstufe des Katalysators und der lokalen Geometrie, kombiniert mit theoretischen Berechnungen, zeigt, dass die Einfügung von Pd in die Knotenpunkte der Cu‐Schaufelradstruktur des MOFs die Adsorption des Schlüsselintermediats COOH* am Cu‐Zentrum fördert. Dies ermöglicht CO‐selektive katalytische Mechanismen und verbessert somit unser Verständnis über das Zusammenspiel von Struktur und Aktivität bei der elektrochemischen CO 2 ‐Reduktion unter Verwendung molekularer Katalysatoren.

Zhang, Ruirui↗
NASA NTRS2010

Three-Dimensional Computed Tomography as a Method for Finding Die Attach Voids in Diodes

NASA analyzes electrical, electronic, and electromechanical (EEE) parts used in space vehicles to understand failure modes of these components. The diode is an EEE part critical to NASA missions that can fail due to excessive voiding in the die attach. Metallography, one established method for studying the die attach, is a time-intensive, destructive, and equivocal process whereby mechanical grinding of the diodes is performed to reveal voiding in the die attach. Problems such as die attach pull-out tend to complicate results and can lead to erroneous conclusions. The objective of this study is to determine if three-dimensional computed tomography (3DCT), a nondestructive technique, is a viable alternative to metallography for detecting die attach voiding. The die attach voiding in two- dimensional planes created from 3DCT scans was compared to several physical cross sections of the same diode to determine if the 3DCT scan accurately recreates die attach volumetric variability

Brahm, E. N.↗
NASA NTRS1978

Development and evaluation of die materials for use in the growth of silicon ribbons by the inverted ribbon growth process, task 2. LSSA project

The results of emission spectroscopic analysis indicate that molten silicon can remain in contact with hot-pressed Si3N4 (99.2 percent theoretical density) for prolonged periods without attaining the impurity content level of the nitride. Although MgO was used as binder, Mg was not found present in the silicon sessile drop in quantities much above the level initially present in the silicon source material. Preliminary experiments with EFG-type dies coated with CVD Si3N4 or CVD SiOxNy indicate that capillary rise does not occur readily in these dies. The same was found to be true of hot-pressed and reaction-sintered Si3N4 obtained commercially. However, when dies were formed by depositing CVD layers on shaped silicon slabs, a column of molten silicon was maintained in each CVD die while being heated in contact with a crucible of molten silicon. Preliminary wetting of dies appears necessary for EFG growth. Several ribbon growth experiments were performed from V-shaped dies.

Duffy, M. T.↗
DOE OSTI2024

Production of Readily Compressible Dies for the Enhanced Sintering of Solids (PRESS) Preliminary Investigations

Non-oxide ceramics, which consist of predominantly carbides, borides, and nitrides, are of great interest to modern engineering because of their resistance to extreme conditions. Properties of such materials include high temperature resistance, high hardness, chemical resistance, and high fracture toughness. However, the main method for manufacturing parts of these materials is by machining cylindrical billets to the desired geometry. Not only does this produce waste, but the cost of machining is high since the part materials are of such high hardness. This method is used because these non-oxide ceramics must be sintered to high density using simultaneous heat and pressure within a hot-pressing unit. These units are inherently restricted to cylindrical geometries. A proposed way to expand the capabilities of a hot-press is by using intermediate compressible dies. This method consists of surrounding a ceramic part green body with a material that will shrink at the same rate as the part and survive the hot-pressing conditions. At the end, the compressible die material would be removed leaving a nearly net shaped hot-pressed part. In this study, graphite powder was investigated as the compressible die material with its shrinkage rate being controlled by particle size mixing. Both ceramic materials and graphite were then cast into parts and compressible dies respectively to show the feasibility of the compressible die hot-pressing method.

36 MATERIALS SCIENCE↗
NASA NTRS1999

Die Attachment for -120 C to +20 C Thermal Cycling of Microelectronics for Future Mars Rovers: An Overview

Active thermal control for electronics on Mars Rovers imposes a serious penalty in weight, volume, power consumption, and reliability. Thus, we propose that thermal control be eliminated for future Rovers. From a functional standpoint there is no reason that the electronics could not operate over the entire temperature range of the Martian environment, which can vary from a low of approximately equal -90 C to a high of approximately equal +20 C during the Martian night and day. The upper end of this range is well within that for conventional electronics. Although the lower end is considerably below that for which conventional--even high-reliability electronics is designed or tested, it is well established that electronic devices can operate to such low temperatures. The primary concern is reliability of the overall electronic system, especially in regard to the numerous daily temperature cycles that it would experience over the duration of a mission on Mars. Accordingly, key reliability issues have been identified for elimination of thermal control on future Mars Rovers. One of these is attachment of semiconductor die onto substrates and into packages. Die attachment is critical since it forms a mechanical, thermal and electrical interface between the electronic device and the substrate or package. This paper summarizes our initial investigation of existing information related to this issue, in order to form an opinion whether die attachment techniques exist, or could be developed with reasonable effort, to withstand the Mars thermal environment for a mission duration of approximately I year. Our conclusion, from a review of literature and personal contacts. is that die attachment can be made sufficiently reliable to satisfy the requirements of future Mars Rovers. Moreover, it appears that there are several possible techniques from which to choose and that the requirements could be met by judicious selection from existing methods using hard solders, soft solders, or organic adhesives. Thus from the standpoint of die attachment. it appears feasible to eliminate thermal control for Rover electronics. We recommend that this be further investigated and verified for the specific hardware and thermal conditions appropriate to Mars Rovers.

Kirschman, Randall K.↗
NASA NTRS2012

Chandra Observations of Dying Radio Sources in Galaxy Clusters

Context. The dying radio sources represent a very interesting and largely unexplored stage of the active galactic nucleus (AGN) evolution. They are considered to be very rare, and almost all of the few known ones were found in galaxy clusters. However, considering the small number detected so far, it has not been possible to draw any firm conclusions about their X-ray environment. Aims. We present X-ray observations performed with the Chandra satellite of the three galaxy clusters Abell 2276, ZwCl 1829.3+6912, and RX J1852.1+5711, which harbor at their center a dying radio source with an ultra-steep spectrum that we recently discovered. Methods. We analyzed the physical properties of the X-ray emitting gas surrounding these elusive radio sources. We determined the global X-ray properties of the clusters, derived the azimuthally averaged profiles of metal abundance, gas temperature, density, and pressure. Furthermore, we estimated the total mass profiles. Results. The large-scale X-ray emission is regular and spherical, suggesting a relaxed state for these systems. Indeed, we found that the three clusters are also characterized by significant enhancements in the metal abundance and declining temperature profiles toward the central region. For all these reasons, we classified RX J1852.1+5711, Abell 2276, and ZwCl 1829.3+6912 as cool-core galaxy clusters. Conclusions. We calculated the non-thermal pressure of the radio lobes assuming that the radio sources are in the minimum energy condition. For all dying sources we found that this is on average about one to two orders of magnitude lower than that of the external gas, as found for many other radio sources at the center of galaxy groups and clusters. We found marginal evidence for the presence of X-ray surface brightness depressions coincident with the fossil radio lobes of the dying sources in A2276 and ZwCl 1829.3+691. We estimated the outburst age and energy output for these two dying sources. The energy power from the AGN outburst is significantly higher than the X-ray luminosity in both clusters. Indeed, it is sufficient that a small fraction of this power is dissipated in the intra-cluster medium to reheat the cool cores.

Murgia, M.↗
DOE OSTI2024

Effect of die design on microstructure and mechanical joint strength in friction self-piercing riveted AA7055-T76 and AA7055-T76

In the present study, a unique friction self-piercing riveting (F-SPR) was applied to join high-strength, low-ductility aluminum alloy (AA) 7055-T76 and AA7055-T76 to mitigate a cracking issue. Also, the effect of die design on both joint formation and the mechanical joint performance were investigated. A crack-free joint was achieved when joining AA7055-T76 and AA7055-T76 by F-SPR. As the bottom diameter of the die increased, the mechanical interlocking distance initially increased then became almost saturated. At the same time, the solid-state bonding gradually disappeared, and the lap-shear fracture changed from bottom aluminum fracture to rivet pull-out with partial bottom aluminum fracture. The average maximum lap-shear joint strength of 11.57 kN and cross tension of 5.65 kN were achieved from the D2 die design owing to the combined contributions from high mechanical interlocking distance and good solid-state bonding at the joint interface. Ultrafine grain refinement was observed at the region next to the rivet shank outer surface and along the materials flow line between the top and bottom aluminum sheet in the rivet cavity. Further, because of the same joint-process parameters, the hardness profile at the joints made by different dies did not show obvious differences. As the distance from the base metal to the rivet outer surface decreased, frictional heat caused the hardness to initially decrease from 190 to 150 HV in the heat-affected zone. Hardness increased up to 175 HV in the thermomechanical affected zone (TMAZ-I) owing to large plastic deformation.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Wire Arc Additive Manufacturing of Lightweight High Pressure Die Casting Tooling

Oak Ridge National Laboratory (ORNL) and Mercury Marine partnered to develop and test methods for additively manufactured tooling for aluminum die casting applications under CRADA agreement NFE-20-08193. Tooling is the largest capital expense for high production casting projects. The lead time for tooling is often measured in months with a typical project taking 9-12 months to realize Production Part Approval Process (PPAP) ready die cast samples. This project demonstrated the technical viability of rapidly produced steel components for high pressure die casting tooling via Wire Arc Additive Manufacturing (WAAM). A 410 stainless steel tool was redesigned and optimized with conformal cooling channels and additively manufactured. The finished tool was tested and used to produce over 4000 parts, which well surpassed expectations. A secondary objective was to evaluate the durability of multi-material additively manufactured (AM) components with conformal cooling. A large multi-material tool (H13 and 410SSNiMo) was manufactured using the same methods showing potential reductions in used material and cost. However, the H13 section sustained material cracking. Further analysis showed that the potential cause was the CTE mismatch of the two materials at higher temperatures. It is also suggested that the material mix can be used if the steel processing temperature does not exceed 600 ̊C.This project has shown high potential for using the WAAM technology for creating AM parts for aluminum dies casting. However, the multi-material approach requires extended study and tests.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2025

Wire Arc Additive Manufacturing of Lightweight High Pressure Die Casting Tooling

Oak Ridge National Laboratory (ORNL) and Mercury Marine partnered to develop and test methods for additively manufactured tooling for aluminum die casting applications under CRADA agreement NFE- 20-08193. Tooling is the largest capital expense for high production casting projects. The lead time for tooling is often measured in months with a typical project taking 9-12 months to realize Production Part Approval Process (PPAP) ready die cast samples. This project demonstrated the technical viability of rapidly produced steel components for high pressure die casting tooling via Wire Arc Additive Manufacturing (WAAM). A 410 stainless steel tool was redesigned and optimized with conformal cooling channels and additively manufactured. The finished tool was tested and used to produce over 4000 parts, which well surpassed expectations. A secondary objective was to evaluate the durability of multi-material additively manufactured (AM) components with conformal cooling. A large multi-material tool (H13 and 410SSNiMo) was manufactured using the same methods showing potential reductions in used material and cost. However, the H13 section sustained material cracking. Further analysis showed that the potential cause was the CTE mismatch of the two materials at higher temperatures. It is also suggested that the material mix can be used if the steel processing temperature does not exceed 600 ˚C. This project has shown high potential for using the WAAM technology for creating AM parts for aluminum dies casting. However, the multi-material approach requires extended study and tests.

36 MATERIALS SCIENCE↗
NASA NTRS1978

Development and Evaluation of Die Materials for Use in the Growth of Silicon Ribbons by the Inverted Ribbon Growth Process. Task 2: LSSA Project

Several ribbon growth experiments were performed from V-shaped dies coated with CVD Si3N4. The most significant result was the ability to perform five consecutive growth runs from the same die without mechanical degradation of the die through temperature cycling. The die was made from vitreous carbon coated with CVD Si3N4. Silicon oxynitride, Si2N2O, was examined with respect to thermal stability in contact with molten silicon. The results of X-ray analysis indicate that this material is converted to both alpha - and beta-Si3N4 in the presence of molten silicon. Experiments on the stability of CVD SiOxNy shoe that this material can be maintained in contact with molten silicon (sessile drop test) for greater than 30 h at 1450 C without total decompositon. These layers are converted mainly to beta-Si3N4.

Duffy, M. T.↗
DOE OSTI2024

Friction stir processing on a strontium modified, thin-wall, vacuum-assisted high-pressure die-cast Aural-5 alloy to improve tensile and fatigue performance

Here, this study explores the application of friction stir processing (FSP) to enhance the material properties of Sr-modified Aural-5 alloy, with a focus on improved tensile and fatigue properties. Aural-5 is a well-known vacuum-assisted high-pressure die-cast (HPDC) Al-Si7-Mg alloy used in the automotive industry to reduce vehicle weight, enhance fuel efficiency, and lower carbon emissions. This alloy modifies its material chemistry with Sr for fine fibrous networks of eutectic silicon and manganese (Mn) to reduce die soldering. It has significantly less iron (Fe) content resulting in the elimination of detrimental needle-shaped Fe-bearing ß-phase intermetallic and improving ductility. The initial microstructure of as-received HPDC Aural-5 exhibits shrinkage porosity in the middle section, a dendritic microstructure with fibrous Al-Si eutectic colonies, a shear-band structure beneath the die-wall, large dendritic externally solidified crystals (ESCs), needle-shaped Mg 2 Si phase and significant second-phase particulates. Some of those microstructural features, such as porosity, ESCs, needle-shaped Mg 2 Si phase, and large second-phase particles, serve as initiation sites for cracks under mechanical loading, resulting in adverse effects on tensile properties, particularly ductility. FSP effectively transforms the microstructure into a wrought configuration with uniform particle distribution by eliminating porosity and disintegrating dendrites, eutectic colonies, ESCs, second-phase particles, and shear-band structures. FSP-driven microstructure modification enhances yield strength and tensile ductility by ~30% and ~35%, respectively. The fatigue life of the material in a bending mode configuration (stress ratio R = 0.1) after FSP exhibits enhancements ranging from 2.0 to 3.9 times that of the original HPDC Aural-5 alloy, depending on the applied stress level.

36 MATERIALS SCIENCE↗