Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DEFLECTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2017

Characteristics of a high-power ion beam deflection system necessary to deflect the hypothetical asteroid 2017 PD

The July 2027 impact date for the hypothetical asteroid 2017 PDC, that is the subject of an emergency response exercise, leaves just over ten years to implement a deflection approach. The analyses herein allocates four years to the design, fabrication, assembly, test and launch of a notional high-power Ion Beam Deflection (IBD) vehicle to meet a launch readiness date no later than May 2021. Using this launch date along with estimates for the vehicle mass and performance characteristics of the electric propulsion system, low-thrust trajectory analyses indicate a 2.56-year flight time to rendezvous with 2017 PDC. This would leave 3.6 years to execute the actual deflection phase. A 160-kW IBD vehicle could deflect 2017 PDC by at least one Earth radius within this time provided the asteroid’s actual diameter was less than about 140 m and its density was 2 g/cm3 or less. Larger diameters and/or higher densities would require a higher power IBD vehicle, multiple IBD vehicles, or a longer deflection phase. Ion beam deflection is largely independent of the characteristics of the threat object, but its effectiveness, like all deflection approaches, is sensitive to both the asteroid mass and the time available for deflection. The characteristics of IBD, i.e., large standoff distance between the spacecraft and the asteroid surface, as well as ion beam divergence angles of a few degrees, facilitates the possible simultaneous use of multiple IBD vehicles to improve the performance and robustness of the asteroid deflection. The 65-cm diameter, 20-kW NEXIS ion thruster developed in support of the Jupiter Icy Moons Orbiter mission concept is particularly well suited for application to a high-power IBD system. It has demonstrated an ion beam divergence angle of approximately 2 degrees and operation at 20 kW for over 2,000 hours. Completion of the development and flight qualification of this technology would significantly reduce the risk and time necessary to respond to the discovery of potentially hazardous asteroid in the size range of 50- to 100-m diameter.

Reeves, David↗
NASA NTRS1987

Component mode synthesis and large deflection vibration of complex structures. Volume 2: Single-mode large deflection vibrations of beams and plates using finite element method

A finite element method is presented for the large amplitude vibrations of complex structures that can be modelled with beam and rectangular plate elements subjected to harmonic excitation. Both inplane deformation and inertia are considered in the formulation. Derivation of the harmonic force and nonlinear stiffness matrices for a beam and a rectangular plate element are presented. Solution procedures and convergence characteristics of the finite element method are described. Nonlinear response to uniform and concentrated harmonic loadings and improved nonlinear free vibration results are presented for beams and rectangular plates of various boundary conditions.

Mei, Chuh↗
NASA NTRS1990

Igniter adapter-to-igniter chamber deflection test

Testing was performed to determine the maximum RSRM igniter adapter-to-igniter chamber joint deflection at the crown of the inner joint primary seal. The deflection data was gathered to support igniter inner joint gasket resiliency predictions which led to launch commit criteria temperature determinations. The proximity (deflection) gage holes for the first test (Test No. 1) were incorrectly located; therefore, the test was declared a non-test. Prior to Test No. 2, test article configuration was modified with the correct proximity gage locations. Deflection data were successfully acquired during Test No. 2. However, the proximity gage deflection measurements were adversely affected by temperature increases. Deflections measured after the temperature rise at the proximity gages were considered unreliable. An analysis was performed to predict the maximum deflections based on the reliable data measured before the detectable temperature rise. Deflections to the primary seal crown location were adjusted to correspond to the time of maximum expected operating pressure (2,159 psi) to account for proximity gage bias, and to account for maximum attach and special bolt relaxation. The maximum joint deflection for the igniter inner joint at the crown of the primary seal, accounting for all significant correction factors, was 0.0031 in. (3.1 mil). Since the predicted (0.003 in.) and tested maximum deflection values were sufficiently close, the launch commit criteria was not changed as a result of this test. Data from this test should be used to determine if the igniter inner joint gasket seals are capable of maintaining sealing capability at a joint displacement of (1.4) x (0.0031 in.) = 0.00434 inches. Additional testing should be performed to increase the database on igniter deflections and address launch commit criteria temperatures.

Cook, M.↗
NASA NTRS1959

The Effects of Streamwise-Deflected Wing Tips on the Aerodynamic Characteristics of an Aspect Ratio-2 Triangular Wing, Body, and Tail Combination

An investigation has been conducted on a triangular wing and body combination to determine the effects on the aerodynamic characteristics resulting from deflecting portions of the wing near the tips 900 to the wing surface about streamwise hinge lines. Experimental data were obtained for Mach numbers of 0.70, 1.30, 1.70, and 2.22 and for angles of attack ranging from -5 deg to +18 deg at sideslip angles of 0 deg and 5 deg. The results showed that the aerodynamic center shift experienced by the triangular wing and body combination as the Mach number was increased from subsonic to supersonic could be reduced by about 40 percent by deflecting the outboard 4 percent of the total area of each wing panel. Deflection about the same hinge line of additional inboard surfaces consisting of 2 percent of the total area of each wing panel resulted in a further reduction of the aerodynamic center travel of 10 percent. The resulting reductions in the stability were accompanied by increases in the drag due to lift and, for the case of the configuration with all surfaces deflected, in the minimum drag. The combined effects of reduced stability and increased drag of the untrimmed configuration on the trimmed lift-drag ratios were estimated from an analysis of the cases in which the wing-body combination with or without tips deflected was assumed to be controlled by a canard. The configurations with deflected surfaces had higher trimmed lift-drag ratios than the model with undeflected surfaces at Mach numbers up to about 1.70. Deflecting either the outboard surfaces or all of the surfaces caused the directional stability to be increased by increments that were approximately constant with increasing angle of attack at each Mach number. The effective dihedral was decreased at all angles of attack and Mach numbers when the surfaces were deflected.

Peterson, Victor L.↗
NASA NTRS2008

Deflection-Compensating Beam for use inside a Cylinder

A design concept for a beam for a specific application permits variations and options for satisfying competing requirements to minimize certain deflections under load and to minimize the weight of the beam. In the specific application, the beam is required to serve as a motion-controlled structure for supporting a mirror for optical testing in the lower third portion of a horizontal, cylindrical vacuum chamber. The cylindrical shape of the chamber is fortuitous in that it can be (and is) utilized as an essential element of the deflection-minimizing design concept. The beam is, more precisely, a table-like structure comprising a nominally flat, horizontal portion with vertical legs at its ends. The weights of the beam and whatever components it supports are reacted by the contact forces between the lower ends of the legs and the inner cylindrical chamber wall. Whereas the bending moments arising from the weights contribute to a beam deflection that is concave with its lowest point at midlength, the bending moments generated by the contact forces acting on the legs contribute to a beam deflection that is convex with its highest point at midlength. In addition, the bending of the legs in response to the weights causes the lower ends of the legs to slide downward on the cylindrical wall. By taking the standard beam-deflection equations, combining them with the geometric relationships among the legs and the horizontal portion of the beam, and treating the sliding as a component of deflection, it is possible to write an equation for the net vertical deflection as a function of the load and of position along the beam. A summary of major conclusions drawn from the equation characterization is included.

Goodman, Dwight↗
NASA NTRS2011

Design of Spacecraft Missions to Test Kinetic Impact for Asteroid Deflection

There are currently over 8,000 known near-Earth asteroids (NEAs), and more are being discovered on a continual basis. More than 1,200 of these are classified as Potentially Hazardous Asteroids (PHAs) because their Minimum Orbit Intersection Distance (MOID) with Earth's orbit is <= 0.05 AU and their estimated diameters are >= 150 m. To date, 178 Earth impact structures have been discovered, indicating that our planet has previously been struck with devastating force by NEAs and will be struck again. Such collisions are aperiodic events and can occur at any time. A variety of techniques have been proposed to defend our planet from NEA impacts by deflecting the incoming asteroid. However, none of these techniques have been tested. Unless rigorous testing is conducted to produce reliable asteroid deflection systems, we will be forced to deploy completely untested -- and therefore unreliable -- deflection missions when a sizable asteroid on a collision course with Earth is discovered. Such missions will have a high probability of failure. We propose to address this problem with a campaign of deflection technology test missions deployed to harmless NEAs. The objective of these missions is to safely evaluate and refine the mission concepts and asteroid deflection system designs. Our current research focuses on the kinetic impactor, one of the simplest proposed asteroid deflection techniques in which a spacecraft is sent to collide with an asteroid at high relative velocity. By deploying test missions in the near future, we can characterize the performance of this deflection technique and resolve any problems inherent to its execution before needing to rely upon it during a true emergency. In this paper we present the methodology and results of our survey, including lists of NEAs for which safe and effective kinetic impactor test missions may be conducted within the next decade. Full mission designs are also presented for the NEAs which offer the best mission opportunities.

Hernandez, Sonia↗
NASA NTRSDate not supplied

Wind Tunnel Testing of AFC over a Deflected Aileron on the High-Lift Common Research Model

Active flow control (AFC) using discrete fluidic actuators distributed along the span, just upstream of the deflected aileron of the 10% scale high-lift version of the Common Research Model (CRM-HL), was evaluated during a wind tunnel test in the NASA Langley 14- by 22-Foot Subsonic Tunnel. For this set of experiments, a new outboard section was fabricated incorporating a deflectable aileron. Aileron deflection angles of 0, 7.5, 16, and 25 were investigated. This experimental investigation is in response to a recent study by Boeing potential to use AFC with a drooped aileron during takeoff to improve lift-to-drag ratio (L/D) by as much as 5%, depending on AFC mass flow rate. AFC is used at deflection angles above the nominal deflection of 7.5 to control the resulting flow separation that occurs and potentially improve L/D. Improvements in aircraft low-speed L/D can affect vehicle range and/or payload. Tuft flow visualization data, steady and unsteady surface pressure data, and force and moment data are used to compare the flowfields with and without AFC. Parameters varied include actuator momentum coefficient and aileron deflection angle. The surface pressure and tuft flow visualization results indicate that without AFC, the flow over a majority of the aileron upper surface is separated for aileron deflection angles larger than 7.5. When AFC is applied, the flow is reattached to the aileron. Force and moment results show that a local increase in lift leads to an increase in L/D of at least 3.5% using mass flow rates thought to be available from air sources onboard a commercial transport.

AFC↗
NASA NTRSDate not supplied

Wind Tunnel Testing of AFC over a Deflected Aileron on the High-Lift Common Research Model

Active flow control (AFC) using discrete fluidic actuators distributed along the span, just upstream of the deflected aileron of the 10% scale high-lift version of the Common Research Model (CRM-HL), was evaluated during a wind tunnel test in the NASA Langley 14- by 22-Foot Subsonic Tunnel. For this set of experiments, a new outboard section was fabricated incorporating a deflectable aileron. Aileron deflection angles of 0, 7.5, 16, and 25 were investigated. This experimental investigation is in response to a recent study by Boeing potential to use AFC with a drooped aileron during takeoff to improve lift-to-drag ratio (L/D) by as much as 5%, depending on AFC mass flow rate. AFC is used at deflection angles above the nominal deflection of 7.5 to control the resulting flow separation that occurs and potentially improve L/D. Improvements in aircraft low-speed L/D can affect vehicle range and/or payload. Tuft flow visualization data, steady and unsteady surface pressure data, and force and moment data are used to compare the flowfields with and without AFC. Parameters varied include actuator momentum coefficient and aileron deflection angle. The surface pressure and tuft flow visualization results indicate that without AFC, the flow over a majority of the aileron upper surface is separated for aileron deflection angles larger than 7.5. When AFC is applied, the flow is reattached to the aileron. Force and moment results show that a local increase in lift leads to an increase in L/D of at least 3.5% using mass flow rates thought to be available from air sources onboard a commercial transport.

AFC↗
NASA NTRS1983

Heating measurements on Space Shuttle Orbiter models with differentially deflected elevons

The phase-change paint technique was used to make heat-transfer measurements on five Space Shuttle Orbiter models with differentially-deflected elevons. The outboard elevons were deflected windward through an angle delta when the inboard elevons were deflected through an angle - 2delta, where delta = 0, 5, 10, 15, and 20 deg. The models were tested in air at Mach 6 and Mach 10 with two different flow conditions at each Mach number. Each test was run at three angles of attack; 20, 28, and 35 deg. This study was restricted to the windward side of the wing/elevons area. Multiple chord-wise streaks of high heating often occurred on the wings and sometimes extended to localized spots of high heating on the windward-deflected elevons. The extent of heating was a function of angle of attack and test conditions, but in general differential deflection of the elevons affected the wing heat-transfer coefficient on the order of 40 percent or less whereas the windward elevon heat-transfer coefficient was a function of the deflection angle and could be many times the value determined for the undeflected elevon.

Wells, W. L.↗
NASA NTRS1938

The Torsional and Bending Deflection of Full-Scale Aluminum-Alloy Propeller Blades Under Normal Operating Conditions

The torsional deflection of the blades of three full-scale aluminum-alloy propellers operating under various loading conditions was measured by a light-beam method. Angular bending deflections were also obtained as an incidental part of the study. The deflection measurements showed that the usual present-day type of propeller blades twisted but a negligible amount under ordinary flight conditions. A maximum deflection of about 1/10 degree was found at a v/nd of 0.3 and a smaller deflection at higher values of v/nd for the station at 0.70 radius. These deflections are much smaller than would be expected from earlier tests, but the light-beam method is considered to be much more accurate than the direct-reading-transit method used in the previous test.

Hartman, Edwin P↗
NASA NTRS1961

An Investigation of Wing and Aileron Loads Due to Deflected Inboard and Outboard Ailerons on a 4-Percent-Thick 30 deg Sweptback Wing at Transonic Speeds

An investigation has been conducted in the Langley 16-foot transonic tunnel to determine the changes in wing loading characteristics due to deflections of a plain faired flap-type inboard aileron, a plain faired flap-type outboard aileron, and a slab-sided thickened trailing edge outboard aileron. The test wing was 4 percent thick and had 30 sweep of the quarter chord, an aspect ratio of 3.0, a taper ratio of 0.2, and NACA 65A004 airfoil sections. The loading characteristics of the deflected ailerons were also investigated. The model was a sting-mounted wing-body combination, and pressure measurements over one wing panel (exposed area) and the ailerons were obtained for angles of attack from 0 to 20 at deflections up to +/- 15 deg for Mach numbers between 0.80 and 1.03. The test Reynolds number based on the wing mean aerodynamic chord was about 7.4 x 10(exp 6). The results of the investigation indicated that positive deflection of the plain faired flap-type inboard aileron caused significant added loading over the wing sections outboard of the aileron at all Mach numbers for model angles of attack from 0 deg or 4 deg up to 12 deg. Positive deflection of the two outboard ailerons (plain faired and slab sided with thickened trailing edge) caused significant added loading over the wing sections inboard of the ailerons for different model angle-of-attack ranges at the several test Mach numbers. The loading shapes over the ailerons were irregular and would be difficult to predict from theoretical considerations in the transonic speed range. The longitudinal and lateral center-of-pressure locations for the ailerons varied only slightly with increasing angle of attack and/or Mach number. Generally, the negative slopes of the variations of aileron hinge-moment coefficient with aileron deflection for all three ailerons varied similarly with Mach number at the test angles of attack.

Whitcomb, Charles F.↗
NASA NTRS2005

Deflection-Based Aircraft Structural Loads Estimation with Comparison to Flight

Traditional techniques in structural load measurement entail the correlation of a known load with strain-gage output from the individual components of a structure or machine. The use of strain gages has proved successful and is considered the standard approach for load measurement. However, remotely measuring aerodynamic loads using deflection measurement systems to determine aeroelastic deformation as a substitute to strain gages may yield lower testing costs while improving aircraft performance through reduced instrumentation weight. With a reliable strain and structural deformation measurement system this technique was examined. The objective of this study was to explore the utility of a deflection-based load estimation, using the active aeroelastic wing F/A-18 aircraft. Calibration data from ground tests performed on the aircraft were used to derive left wing-root and wing-fold bending-moment and torque load equations based on strain gages, however, for this study, point deflections were used to derive deflection-based load equations. Comparisons between the strain-gage and deflection-based methods are presented. Flight data from the phase-1 active aeroelastic wing flight program were used to validate the deflection-based load estimation method. Flight validation revealed a strong bending-moment correlation and slightly weaker torque correlation. Development of current techniques, and future studies are discussed.

Lizotte, Andrew M.↗
NASA NTRS2005

Deflection-Based Structural Loads Estimation From the Active Aeroelastic Wing F/A-18 Aircraft

Traditional techniques in structural load measurement entail the correlation of a known load with strain-gage output from the individual components of a structure or machine. The use of strain gages has proved successful and is considered the standard approach for load measurement. However, remotely measuring aerodynamic loads using deflection measurement systems to determine aeroelastic deformation as a substitute to strain gages may yield lower testing costs while improving aircraft performance through reduced instrumentation weight. This technique was examined using a reliable strain and structural deformation measurement system. The objective of this study was to explore the utility of a deflection-based load estimation, using the active aeroelastic wing F/A-18 aircraft. Calibration data from ground tests performed on the aircraft were used to derive left wing-root and wing-fold bending-moment and torque load equations based on strain gages, however, for this study, point deflections were used to derive deflection-based load equations. Comparisons between the strain-gage and deflection-based methods are presented. Flight data from the phase-1 active aeroelastic wing flight program were used to validate the deflection-based load estimation method. Flight validation revealed a strong bending-moment correlation and slightly weaker torque correlation. Development of current techniques, and future studies are discussed.

Lizotte, Andrew M.↗
NASA NTRS1997

Fan Blade Deflection Measurement and Analyses Correlation

Steady deflection measurements were taken of two identical NASA/Pratt & Whitney-designed fan blades while they were rotating in a vacuum in NASA Lewis Research Center's Dynamic Spin Facility. The one-fifth-scale fan blades, which have a tip diameter of 22 in. and a pinroot retention, are of sparshell construction and were unducted for this test. The purpose of the test was to measure the change of the radial deflection of the blade tip and blade angle at selected radial stations along the blade span with respect to rotational speed. The procedure for radial deflection measurement had no precedent and was newly developed for this test. Radial deflection measurements were made to assure adequate tip clearance existed between the fan blades and the duct for a follow-on wind tunnel test. Also, blade angle deflection measurements were desired before pitchsetting parts for the wind tunnel test were finish machined. During the test, laser beams were aimed across the blade path into photodiodes to give signals that were used to determine blade angle change or tip radial deflection. These laser beams were set parallel to the spin axis at selected radial stations.

Mehmed, Oral↗