Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Constants”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Mineral Scale Formation during Crossflow Reverse Osmosis at Constant Flux and Constant Transmembrane Pressure Conditions

Mineral scale formation on membrane surfaces is a significant challenge in reverse osmosis water purification. Laboratory fouling experiments are typically run such that the transmembrane pressure (TMP) is fixed, and the permeate flux decreases over time as scales accumulate on the membrane surface. However, this change in flux means that the hydrodynamic conditions at the membrane surface are continuously changing, which could affect crystallization and foulant deposition processes. Operating under constant permeate flux conditions, in contrast, is advantageous because it keeps the hydrodynamic conditions relatively consistent, making it possible to compare how membrane properties (e.g., surface chemistry) affect fouling propensity. Industrial reverse osmosis operations are not run strictly in either constant TMP or constant flux mode; while they may start at a constant TMP, feed pressure may be periodically adjusted to maintain permeate water production within a specified range. Here, the scarcity of constant permeate flux reverse osmosis scaling experiments reported in the literature frustrates efforts to compare membrane fouling processes under constant TMP and constant flux conditions. For the first time, the evolution of the fouling layer resistance was compared as a function of cumulative permeate volume per membrane area during constant TMP and constant flux reverse osmosis filtrations. Scaling experiments were conducted by challenging commercial reverse osmosis membranes with a model feed solution nearly saturated with calcium sulfate dihydrate (gypsum). At low fluxes, the increase in fouling layer resistance was quantitatively similar for the two operational modes. In contrast, at high fluxes, the fouling layer resistance increased more rapidly in constant flux filtration than in constant TMP filtration. The mechanism of scale formation in constant TMP and constant flux operation was self-limiting and self-reinforcing, respectively.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Uncertainty quantification in elastic constants of SiC f /SiC m tubular composites using global sensitivity analysis

Silicon carbide fiber and silicon carbide matrix (SiC f /SiC m ) tubes produced through the chemical vapor infiltration process have become a candidate cladding material in nuclear applications. The performance of this composite is influenced by many variables such as braiding angle, porosity, material properties, etc., which vary over a range of values due to the inherent fluctuations in the manufacturing process. In this study, the variability in elastic constants of SiC f /SiC m composite has been quantified through multiscale finite element (FE) simulations, variable screening, and high-fidelity surrogate modeling. The key variables dominantly affecting the elastic constants of SiC f /SiC m tubes were identified using global sensitivity analysis. A surrogate to the high-fidelity FE-based model was used in Monte Carlo simulations to generate a hundred thousand samples from which the uncertainty in elastic constants was assessed. It turned out that the coefficient of variation was less than 10%.

Materials Science↗
DOE OSTI2023

Electrochemistry at Back-Gated, Ultrathin ZnO Electrodes: Field-Effect Modulation of Heterogeneous Electron Transfer Rate Constants by 30× with Enhanced Gate Capacitance

We report steady-state voltammetry of outer-sphere redox species at back-gated ultrathin ZnO working electrodes in order to determine electron transfer rate constants k ET as a function of independently-controlled gate bias, V G . We demonstrate that k ET can be modulated as much as 30-fold by application of V G ≤ 8 V. Key to this demonstration was integrating the ultrathin (5 nm) ZnO on a high dielectric constant (k) insulator, HfO 2 (30 nm), which was grown on a Pd metal gate. The high-k HfO 2 dramatically decreased the required V G values and increased the gate-induced charge in ZnO compared to previous studies. Importantly, the enhanced gating power of the Pd/HfO 2 /ZnO stack meant it was possible to observe a non-monotonic dependence of k ET on V G , which reflects the inherent density of redox acceptor states in solution. Furthermore, this work adds to the growing body of literature demonstrating that electrochemical kinetics (i.e., rate constants and overpotentials) at ultrathin working electrodes can be tuned by V G , independent of the conventional electrochemical working electrode potential.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Thermodynamics of electrolyte solutions near charged surfaces: Constant surface charge vs constant surface potential

Electric double layers are ubiquitous in science and engineering and are of current interest, owing to their applications in the stabilization of colloidal suspensions and as supercapacitors. While the structure and properties of electric double layers in electrolyte solutions near a charged surface are well characterized, there are subtleties in calculating thermodynamic properties from the free energy of a system with charged surfaces. These subtleties arise from the difference in the free energy between systems with constant surface charge and constant surface potential. In this work, we present a systematic, pedagogical framework to properly account for the different specifications on charged bodies in electrolyte solutions. Our approach is fully variational—that is, all free energies, boundary conditions, relevant electrostatic equations, and thermodynamic quantities are systematically derived using variational principles of thermodynamics. We illustrate our approach by considering a simple electrolyte solution between two charged surfaces using the Poisson–Boltzmann theory. Our results highlight the importance of using the proper thermodynamic potential and provide a general framework for calculating thermodynamic properties of electrolyte solutions near charged surfaces. Specifically, we present the calculation of the pressure and the surface tension between two charged surfaces for different boundary conditions, including mixed boundary conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Distance-dependent dielectric constant at the calcite/electrolyte interface: Implication for surface complexation modeling

Hypothesis: The electrical double layer formed at the mineral/electrolyte interface is often modeled using mean-field approaches based on a continuum description of the solvent whose dielectric constant is assumed to decrease monotonically with decreasing distance to the surface. In contrast, molecular simulations show that the solvent polarizability oscillates near the surface similar to the water density profile - as shown previously, for example, by Bonthuis et al. (D.J. Bonthuis, S. Gekle, R.R. Netz, Dielectric Profile of Interfacial Water and its Effect on Double-Layer Capacitance, Phys Rev Lett 107(16) (2011) 166102). Here, we showed that molecular and mesoscale pictures agree by spatially averaging the dielectric constant obtained from molecular dynamics simulations over the distances relevant to the mean-field representation. In addition, the values of capacitances used to describe the electrical double layer in Surface Complexation Models (SCMs) of the mineral/electrolyte interface can be estimated using molecularly informed spatially averaged dielectric constants and positions of hydration layers. Experiments: First, we used molecular dynamics simulations to model the calcite 101¯4/electrolyte interface. Next, by using atomistic trajectories, we calculated the distance-dependent static dielectric constant and water density in the direction normal to the. Finally, we applied spatial compartmentalization consistent with the model of parallel-plate capacitors connected in series to estimate SCM capacitances. Findings: Computationally expensive simulations are required to determine the dielectric constant profile of interfacial water near the mineral surface. On the other hand, water density profiles are readily assessable from much shorter simulation trajectories. Our simulations confirmed that dielectric and water density oscillations at the interface are correlated. Here, we parametrized linear regression models to estimate the dielectric constant directly from the local water density. This is a significant computational shortcut compared to slowly converging calculations relying on total dipole moment fluctuations. The amplitude of the interfacial dielectric constant oscillation can exceed the dielectric constant of the bulk water, suggesting an ice-like frozen state, but only if there are no electrolyte ions. The interfacial accumulation of electrolyte ions causes a decrease in the dielectric constant due to the reduction of water density and re-orientation of water dipoles in ion hydration shells. Finally, we show how to use the computed dielectric properties to estimate SCM's capacitances.

58 GEOSCIENCES↗
DOE OSTI2024

Enhancing the dielectric constant of zwitterionic liquids via dipole moment and anion chemistry

The dielectric constant is a critical parameter in many energy-related applications. Typically, increasing the dielectric constant of soft materials involves adding high dielectric constant polar liquids or inorganic fillers, but there are limitations to this approach due to safety concerns with volatile and flammable solvents and the agglomeration of inorganic fillers. An alternative approach is to add zwitterionic liquids that exhibit exceptionally high dielectric constants with negligible volatility. Here, we report the synthesis of a series of zwitterionic liquids containing an imidazolium cation, exhibiting the highest dielectric constant among all organic molecules (∼350 at 293 K). The cation–anion linkage was tailored in a wide range between three and nine carbons, rendering the zwitterion dipole from 25 to 52 D. Comparing the dielectric constant for zwitterions with different anions (i.e., sulfonylimide, sulfonate, and carboxylate) reveals the beneficial impacts of the delocalized sulfonylimide anion vs the carboxylate anion due to the enlarged molecular dipole and more homogenous liquid morphology. Molecular dipole and liquid morphology are identified as the keys to developing high dielectric constant zwitterionic liquids. The extremely high dielectric constant accessible with the proposed molecular design paves new avenues for developing high dielectric constant zwitterions that act as dielectricizers.

Chemistry↗
DOE OSTI2022

Sensitivity Coefficients Calculated for the Prompt Neutron Decay Constant at or Near Delayed Critical [Abstract]

Experimenters at Los Alamos National Laboratory (LANL) measure the prompt neutron decay constant for many experiments at the National Criticality Experiments Research Center (NCERC) to infer reactivity and the effective neutron multiplication factor. These quantities are very important for nuclear criticality safety and validating nuclear data. Uncertainty in measures of criticality of an experimental configuration can be determined prior to physically performing the experiment by applying first order perturbation theory to Monte Carlo codes, such as MCNP®. The first order perturbation theory produces first derivatives of some nuclear parameter to nuclear data (e.g., cross section data). This first derivative is commonly referred to as a sensitivity coefficient. Currently, the MCNP® software has the capability of computing effective neutron multiplication factor sensitivity coefficients to cross section data. This work builds off of this MCNP® capability and the first order perturbation theory to provide a method of calculating sensitivity coefficients for the prompt neutron decay constant at or near delayed critical to cross section data. The prompt neutron decay constant sensitivity coefficient calculated in this work does not depend on any modification of the MCNP® source code. Prompt neutron decay constant sensitivity coefficient calculations can be used to infer reactivity and effective neutron multiplication factor sensitivity coefficient values as well. By investigating the trends of prompt neutron decay constant sensitivity coefficients for nuclide-reaction pairs across energy spectra, experiments can be designed to maximize or minimize the uncertainty in the prompt neutron decay constant in a particular energy region, which can lead to further optimization studies. Prompt neutron decay constant sensitivity coefficients will be calculated for the Jezebel benchmark. Subsequently, these sensitivity coefficients will be used in a data assimilation process to determine if there is or are optimal experiments that can be performed to provide insight into adjustments of uncertain/inaccurate cross section data. Specifically, the effect of the prompt neutron decay constant sensitivity coefficients on the nuclear data-induced uncertainty in the effective neutron multiplication factor will be examined

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2022

Re-evaluation of rate constants for the reaction N 2 H 4 (+ M) $^→_←$ NH 2 + NH 2 (+ M)

Rate constants for the dissociation/recombination reaction N 2 H 4 (+ M) $^→_←$ NH 2 + NH 2 (+ M) are determined by a combination of quantum-chemical calculations and statistical unimolecular rate theory. Between 1100 and 2500 K, limiting low-pressure rate constants for hydrazine dissociation in the bath gas Ar of k 0 = [Ar] 6.1 × 10 20 (T/1000 K) –7.3 exp (-34490 K/T) cm 3 mol –1 s –1 , limiting high-pressure rate constants of k ∞ = 7.6 × 10 16 (T/1000 K) –1.0 exp(-33600 K/T) s –1 , and center broadening factors of the falloff curves (between 1100 and 1600 K in Ar) of F cent = 0.71 exp(- T/1460 K) + 0.29 exp(- T/21 K) + exp(-13400 K/T) were calculated. Using equilibrium constants K C = 1.7 × 10 3 (T/1000 K) –1.5 exp(-33,460 K/T) mol cm –3 , between 300 and 600 K limiting low-pressure rate constants for the reverse recombination of NH 2 radicals in the bath gas N 2 of k rec,0 = [N 2 ] 4.4 × 10 20 (T/400 K) –6.9 exp (-1630 K/T) cm 6 mol –2 s –1 , limiting high-pressure rate constants of k rec,∞ = 4.4 × 10 13 (T/1000 K) 0.44 exp(-140 K/T) cm 3 mol -1 s –1 , and center broadening factors (between 300 and 600 K in N 2 ) of F cent = exp(- T/1130 K) + exp (-10340 K/T) were obtained. A comparison with experimental results for hydrazine dissociation from the literature suggests incomplete falloff extrapolations toward k ∞ and experimental problems in the determination of k 0 at temperatures above about 1600 K. Finally, implications of the present re-evaluated rate constants for the modeling of high temperature ammonia oxidation kinetics are discussed, showing an only small influence of their precise values on the overall properties of the process.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Investigating the dielectric constant of barium titanate in a polymer-matrix nanocomposite

Barium titanate (BTO) is a ferroelectric material used in capacitors because of its high bulk dielectric constant. However, the impact of the size of BTO on its dielectric constant is not yet fully understood and is highly contested. Here, we present an investigation into the dielectric constant of BTO nanoparticles with diameters ranging between 50 and 500 nm. BTO nanoparticles were incorporated into acrylonitrile butadiene styrene and injection molded into parallel plate capacitors, which were used to determine nanocomposite dielectric constants. The dielectric constants of BTO nanoparticles were obtained by combining experimental measurements with computational results from COMSOL simulations of ABS-matrix nanocomposites containing BTO. The dielectric constant of BTO was observed to be relatively constant at nanoparticle diameters as small as 200 nm but sharply declined at smaller nanoparticle sizes. Overall, these results will be useful in the development of improved energy storage and power conditioning systems utilizing BTO nanoparticles.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Second‐ and Third‐Order Elastic Constants of Inert and Energetic Molecular Crystals From Density Functional Theory

Complete tensors of the second- and third-order elastic constants of the organic molecular crystals acetaminophen, pentaerythritol tetranitrate (PETN), cyclotrimethylene trinitramine (RDX), cyclotetramethylene tetranitramine (HMX), 1,1-diamino-2,2-dinitroethylene (FOX-7), hexanitrohexaazaisowurtzitane (CL-20), and erythritol tetranitrate (ETN) have been calculated using dispersion-corrected density functional theory. The sets of second- and third-order elastic constants are expected to provide a more accurate and reliable description of the behavior of these materials under nonhydrostatic loads than pressure- and volume-dependent second-order elastic constants. The tensors of second-order constants have been compared with experimental data and/or other calculations when possible, and with the exception of results for CL-20 from Brillouin scattering experiments, we find good agreement. The calculated third-order elastic constants of PETN are in very good agreement with the subset of third-order constants derived from experimental wave speed measurements. The elastic anisotropies of the crystals have been estimated using the universal elastic anisotropy index, which shows that the crystals fall into three groups with low anisotropy (PETN, RDX, and CL-20), moderate anisotropy (acetaminophen, HMX, and ETN), and high elastic anisotropy (FOX-7).

36 MATERIALS SCIENCE↗
DOE OSTI2020

Charge transfer rate constants for the carotenoid-porphyrin-C 60 molecular triad dissolved in tetrahydrofuran: The spin-boson model vs the linearized semiclassical approximation

Charge transfer rate constants were calculated for the carotenoid-porphyrin-C 60 (CPC 60 ) molecular triad dissolved in explicit tetrahydrofuran. The calculation was based on mapping the all-atom anharmonic Hamiltonian of this system onto the spin-boson Hamiltonian. The mapping was based on discretizing the spectral density from the time correlation function of the donor–acceptor potential energy gap, as obtained from all-atom molecular dynamics simulations. Different spin-boson Hamiltonians were constructed for each of the possible transitions between the three excited electronic states in two different triad conformations. The rate constants of three possible transitions were calculated via the quantum-mechanically exact Fermi’s golden rule (FGR), as well as a progression of more approximate expressions that lead to the classical Marcus expression. The advantage of the spin-boson approach is that once the mapping is established, the quantum-mechanically exact FGR and the hierarchy of approximations are known in closed form. The classical Marcus charge transfer rate constants obtained with the spin-boson Hamiltonians were found to reproduce those obtained from all-atom simulations with the linearized semiclassical approximation, thereby confirming the equivalence of the two approaches for this system. Furthermore, within the spin-boson Hamiltonian, we also found that the quantum-mechanically exact FGR rate constants were significantly enhanced compared to the classical Marcus theory rate constants for two out of three transitions in one of the two conformations under consideration. The results confirm that mapping to the spin-boson model can yield accurate predictions for charge transfer rate constants in a system as complex as CPC 60 dissolved in tetrahydrofuran.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Predicting Elastic Constants of Refractory Complex Concentrated Alloys Using Machine Learning Approach

Refractory complex concentrated alloys (RCCAs) have drawn increasing attention recently owing to their balanced mechanical properties, including excellent creep resistance, ductility, and oxidation resistance. The mechanical and thermal properties of RCCAs are directly linked with the elastic constants. However, it is time consuming and expensive to obtain the elastic constants of RCCAs with conventional trial-and-error experiments. The elastic constants of RCCAs are predicted using a combination of density functional theory simulation data and machine learning (ML) algorithms in this study. The elastic constants of several RCCAs are predicted using the random forest regressor, gradient boosting regressor (GBR), and XGBoost regression models. Based on performance metrics R-squared, mean average error and root mean square error, the GBR model was found to be most promising in predicting the elastic constant of RCCAs among the three ML models. Additionally, GBR model accuracy was verified using the other four RHEAs dataset which was never seen by the GBR model, and reasonable agreements between ML prediction and available results were found. The present findings show that the GBR model can be used to predict the elastic constant of new RHEAs more accurately without performing any expensive computational and experimental work.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Dissociation-induced depletion of high-energy reactant molecules as a mechanism for pressure-dependent rate constants for bimolecular reactions

In 1922, Lindemann proposed the now-well-known mechanism for pressure-dependent rate constants for unimolecular reactions: reactant molecules with sufficiently high energies dissociate more quickly than collisions can reestablish the Boltzmann distribution of the internal energies of the molecule during its dissociation at low pressures – yielding pressure-dependent rate constants for unimolecular reactions due to the preferential depletion of the high energy states capable of dissociation. In the last century, incredible progress has been made in achieving a far greater understanding of and quantitative predictions for unimolecular and association reactions. In the modern era, pressure-dependent phenomenological rate constants are now nearly universally used to describe the rates of unimolecular and associative reactions in phenomenological kinetic modeling. However, there is a second, more indirect, implication of Lindemann’s mechanism that relates to how these dissociation-induced non-equilibrium distributions impact bimolecular reactions, including non-associative bimolecular reactions – which are generally not considered to have pressure-dependent rate constants. Yet, as we show herein, the same high energy states depleted due to dissociation would otherwise react most rapidly in high-activation-energy bimolecular reactions – yielding a mechanism for pressure-dependent rate constants for bimolecular reactions (including non-associative reactions). Here, we present results from a case study for CH 2 O dissociation, isomerization, and bimolecular reaction with O2 to explore this question. Results from our master equation calculations indicate that the effect of dissociation-induced non-equilibrium distributions on bimolecular reactions can be substantial – even when chemical timescales are well separated from internal energy relaxational timescales (i.e. when the traditional rate constant description would be thought to apply). This effect is found to be more pronounced – and more complex – for bimolecular reactions involving molecular entities whose chemical timescales are merged with the internal energy relaxational timescales. Lastly, we present some ideas for discussion regarding what should be considered as “chemical species” in phenomenological kinetic models.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Stability Constants of Lanthanide-nitrate Complexes in Aqueous Solutions: A Theoretical Study

Calculating stability constants for lanthanide--nitrate complexes in aqueous solution is challenging due to the complex free-energy landscapes of the participating species. In this work, we compare cluster-continuum solvation and condensed-phase approaches using universal machine learning interatomic potentials (MLIPs) for determining the stability constants of lanthanide--nitrate complexes in aqueous solutions. Within the cluster--continuum solvation framework at the B3LYP level of theory, reactions involving lanthanide coordination numbers of both 8 and 9 are found to be relevant. After an empirical linear free-energy correction, the cluster--continuum results fall on the same order-of-magnitude scale as the experimental stability constants. By contrast, MACE-MP0 MLIP underestimates lanthanide hydration numbers and gives PMF-derived stability constants with large deviations from experiment, whereas MACE-MATPES-R2SCAN improves both hydration structure and the stability-constant scale but still does not quantitatively reproduce the detailed lanthanide trend. Across both approaches, nitrate binding is best viewed as a labile coordination motif rather than a fixed mono- or bidentate structure, with hydration-shell structure influencing which configurations are favored. Overall, the cluster--continuum calculations provide a practical semi-quantitative baseline for the experimental stability-constant scale, while the explicit-solvent MLIP benchmarks show clear progress from MACE-MP0 to MACE-MATPES-r2SCAN but also highlight the need for lanthanide-targeted training, fine-tuning, or improved long-range and polarization treatments to obtain predictive thermodynamics for complex aqueous lanthanide chemistry.

Dinpajooh, Mohammadhasan↗