SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Results of a performance analysis of an airborne Doppler radar wind shear detection system are given in vugraph form. It was concluded that both CO sub 2 and Ho:YAG lasers are feasible for dry microburst applications, but with limited performance in wet microbursts. The Ho:YAG performs better than the CO sub 2 for a set of identical lidar parameters.
The Martian atmosphere has many features in common with the terrestrial mesosphere. Both share similar pressure and temperature ranges, and much of the same chemistry operates in each. For example, the radical species H, OH, and H(sub 2)O, which comprise the odd hydrogen family, are of central importance in the catalytic destruction of CO and O(sub 3) in both atmospheres. The inclusion of recent chemical kinetics data, specifically temperature dependent CO(sub 2) absorption cross-sections, into our one dimensional photochemical model of the Martial atmosphere shows that oxidation of CO by odd hydrogen is too efficient. The incorporation of smaller cross sections for CO(sub 2) leads to an enhanced photolysis rate of water vapor, increasing odd hydrogen to the point where the predicted mixing ratio of CO in our model is substantially less than the observed value of 6.5 x 10(sup -4). Interestingly, most photochemical models of the terrestrial mesosphere underestimate the CO and O(sub 3) densities using currently accepted photodissociation and kinetic rate coefficients. This has also been attributed to an overabundance of odd hydrogen in the models. We shall show that agreement between models and observations of CO in the Martian atmosphere as well as of CO and O(sub 3) in the terrestrial mesosphere can be achieved by revising the rate constants for the reactions OH + HO(sub 2) and CO + OH within their published uncertainties. The fact that similar revisions alleviate discrepancies in both the terrestrial and Martian atmospheres warrants a re-evaluation of these key rate constants at the appropriate temperatures and pressures.
Discussion of laboratory measurements which indicate that the reaction of the thermalized HO(2) radical with CO is exceedingly slow and that this reaction should not, therefore, be of any significance in atmospheric chemistry. The large discrepancy between the new results and data obtained earlier by Westenberg and de Haas (1972) is explained in terms of the reacting hydroperoxyl radical being in a non-Boltzmann distribution in the former study. It appears that the most important reactions of thermalized HO(2) in the atmosphere are those involving the trace gases of NO and sulfur dioxide.
The most commonly used crystal architecture to produce 2 micrometer laser is co-doping Ho and Tm into a single host crystal. In this method, the stored energy transfer from the Tm (3)F4 to the Ho (5)I7 manifold is not fast enough to warrant high efficiency for short pulse applications. By separating the Ho and the Tm ions and doping the Tm in YALO3 and the Ho in YLF, we were able to directly pump the Ho (5)I7 manifold with 1.94 micrometers. The Ho:YLF laser has produced 33 mJ at 2.062 micrometers with a quantum efficiency of 0.88. The performance of each laser will be presented.
A review of Tm and Ho materials is presented, covering some fundamental aspects on the spectroscopy and laser dynamics in both single and co-doped systems. Following an introduction to 2- m lasers, applications and historical development, the physics of quasi-four level lasers, energy transfer and modeling are discussed in some detail. Recent developments in using Tm lasers to pump Ho lasers are discussed, and seen to offer some advantages over conventional Tm:Ho lasers. This article is not intended as a complete review, but as a primer for introducing concepts and a resource for further study.
The radical amplifier as a method for measuring radical concentrations in the atmosphere has received renewed attention lately. In principle, it can measure the total concentration of HO(x) and RO(x) radicals by reacting ambient air with high concentrations of CO (3-10 percent) and NO (2-6 ppmv), and measuring the NO2 produced.
A Pt/SnO2 catalyst has been developed at NASA Langley that is effective for the oxidation of CO at room temperature (1). A mechanism has been proposed to explain the effectiveness of this catalyst (2), but most of the species involved in this mechanism have not been observed under actual catalytic conditions. A number of these species are potentially detectable by Fourier Transform Infrared Spectroscopy (FTIR), e.g., HOSnO sub x, HO sub y PtO sub z, Pt-CO, and SnHCO3. Therefore a preliminary investigation was conducted to determine what might be learned about this particular catalyst by transmission FTIR. The main advantage of FTIR for this work is that the catalyst can be examined under conditions similar to the actual catalytic conditions. This can be of critical importance since some surface species may exist only when the reaction gases are present. Another advantage of the infrared approach is that since vibrations are probed, subtle chemical details may be obtained. The main disadvantage of this approach is that FTIR is not nearly as sensitive as the Ultra High Vacuum (UHV) surface analytical techniques such as Auger, Electron Spectroscopy for Chemical Analysis (ESCA), Electron Energy Loss Spectroscopy (EELS), etc. Another problem is that the assignment of the observed infrared bands may be difficult.
Induced microwave absorption in carbon dioxide studied at frequency of 9260 mc/sec over temperature range from 270 to 500 degrees K and pressures as high as 95 atm
Fourier transform infrared spectrometry (FTIR) and laser ablation inductively coupled plasma mass spectrometry (LA-ICPMS) were used to determine water, rare earth (REE), lithophile (LILE), and high field strength (HFSE) element contents in garnet and pyroxene from mantle xenoliths, Kaapvaal craton, southern Africa. Water enters these nominally anhydrous minerals as protons bonded to structural oxygen in lattice defects. Pyroxene water contents (150-400 ppm in clinopyroxene; 40-250 ppm in orthopyroxene) correlate with their Al, Fe, Ca and Na and are homogeneous within a mineral grains and a xenolith. Garnets from Jagersfontein are chemically zoned for Cr, Ca, Ti and water contents. Garnets contain 0 to 20 ppm H2 Despite the fast diffusion rate of H in mantle m inerals, the observations above indicate that the water contents of mantle xenolith minerals were not disturbed during kimberlite entrainment and that the measured water data represent mantle values. Trace elements in all minerals show various degrees of light REE and LILE enrichments indicative of minimal to strong metasomatism. Water contents of peridotite minerals from the Kaapvaal lithosphere are not related to the degree of depletion of the peridotites. Instead, metasomatism exerts a clear control on the amount of water of mantle minerals. Xenoliths from each location record specific types of metasomatism with different outcomes for the water contents of mantle minerals. At pressures . 5.5 GPa, highly alkaline melts metasomatized Liqhobong and Kimberley peridotites, and increased the water contents of their olivine, pyroxenes and garnet. At higher pressures, the circulation of ultramafic melts reacting with peridotite resulted in co-variation of Ca, Ti and water at the edge of garnets at Jagersfontein, overall decreasing their water content, and lowered the water content of olivines at Finsch Mine. The calculated water content of these melts varies depending on whether the water content of the peridotite (2 wt% HO. 2O) or individual m inerals (<0.5-13 wt% H2O) are used, and also depend on the mineral-melt water partition coefficients. These metasomatic events are thought to have occurred during the Archean and Proterozoic, meaning that the water contents measured here have been preserved since that time and can be used to investigate viscocity and longevity of cratonic mantle roots.
Multi-line studies of CO-12, CO-13, C-18O, HCN, and HCO(+) at 3 mm, 1.3 mm, and 0.8 mm using the Institute for Radio Astronomy in the Millimeter range (IRAM) 30 m telescope, with the IRAM superconductor insulator superconductor (SIS) receivers and the Max Planck Institute for External Physics (MPE) 350 GHz SIS receiver, show that the densities and temperatures of molecular gas in external galaxies change significantly with position. CO-12 measures the densities and temperature of diffuse interclump molecular gas, but not the bulk of the molecular gas. Simple one-component models, with or without external heating, cannot account for the weakness of the CO-12 J = 3 to 2 line relative to J = 2 to 1 and J = 1 to 0. CO-12 does not trace the bulk of the molecular gas, and optical depth effects obviate a straightforward interpretation of CO-12 data. Instead, researchers turned to the optically thin CO isotopes and other molecular species. Isotopic CO lines measure the bulk of the molecular gas, and HCN and HCO(+) pick out denser regions. Researchers find a warm ridge of gas in IC 342 (Eckart et al. 1989), denser gas in the starburst nucleus of IC 342, and a possible hot-spot in NGC 2903. In IC 342, NGC 2146, and NGC 6764, the CO-13 J = 2 to 1 line is subthermally populated, implying gas densities less than or equal to 10(exp 4) cm(-3).
Inherent susceptibility of adhesive bonds to miniscule quantities of contamination can cause undetectable weakened bonds. For this reason, the Federal Aviation Administration (FAA) places strict regulations on adhesively bonded joints in primary aircraft structures. To meet certification requirements aircraft manufactures resort to redundant load paths in the form of fasteners which inherently add weight to the structure and increase manufacturing time. In prior work, a secondary bonding technique called AERoBOND was developed, which utilized off-stoichiometric epoxymatrix resins to facilitate reflow and diffusion of the resin within the joint interface during a secondary bonding/cure process, thus achieving a bond similar to a co-cured joint. However, the AERoBOND process required tight spatial tolerances between the two parts being joined. This study examined the utilization of conventional adhesive with the AERoBOND method to act as a filler in the joint line, effectively reducing the need for tight tolerances on the joining parts and serving as a flexible alternative for existing manufacturing processes. Ultrasonic inspection, optical microscopy, and ASTM International standard tests were performed to analyze the joints for defects and to quantify the mode-I and mode-II interlaminar fracture toughness and short beam strength of the proposed methodology with varying manufacturing parameters. The comprehensive results indicate that the AERoBOND+ method with and without surface preparation performs comparably to co-cured and conventional, adhesively bonded joints when secondary cured in an autoclave with 791 kPa of pressure. As an example, the AERoBOND+ panel without surface preparation bonded with 791 kPa of pressure (referred to as AB+3 throughout paper) had a mode-I fracture toughness (G Ic ) of 0.643 kJ/m 2 and a mode-II fracture toughness (G IIc ) of 4.000 kJ/m 2 in the non-precracked condition and 4.218 kJ/m 2 in the precracked condition at the adhesive-to-prepreg interface. These results were 96%, 142%, and 217%, respectively, of a co-cured baseline panel (referred to as C1 throughout paper).
Studies undertaken in this project have sought to understand lower thermospheric structure and dynamics (less than or equal to 145 km), particularly the processes responsible. This is a region just below the reach of in-situ instruments onboard PVO (Pioneer Venus Orbiter) during the first few diurnal cycles. PVO remote airglow observations (nitric oxide, O2, visible, O 1304A) have been coupled with ground-based observations (CO densities, winds, temperatures, O2 IR nightglow) to address the behavior of lower thermospheric winds and chemistry over 95 to 150 km. This interpretation of PVO and related data is accomplished by using the NCAR Venus thermospheric general circulation model (VTGCM) (Bougher et al., 1988; 1990). This model has been modified over the last two years to improve its ability to calculate O, CO, and O2 densities, temperatures, nightglow, and subsolar-to-antisolar and zonal winds over 95 to 150 km (Bougher and Borucki, 1992). Our VTGCM studies show that: (1) O2 visible and IR nightglow distributions can be used to trace lower thermosphere / upper mesosphere winds over 100-130 km. Typically, weak zonal winds (less than or equal to 25 m/sec) and nightglow maximum patches near 0100 LT prevail. Occasionally, strong zonal winds (30-60 m/sec) and airglow patches peaking near 0300 LT characterize the Venus lower thermosphere. (2) It is clear that the dynamics of the Venus 90-130 km region is highly variable on time scales as short as an hour. This is most likely due to the time variable nature of upward propagating gravity waves, which grow in amplitude and eventually break. The resulting turbulence gives rise to local time variable eddy diffusion and momentum drag, both of which strongly impact global density and nightglow distributions. (3) The oxygen chemistry (O, O2, etc.) over 90-120 km is strongly dependent on HO(x) and CLO(x) tracer species that must be properly included in any coupled chemical dynamical model. (4) The density profiles of light species (O, CO, N, He) are strongly affected by large-scale transport by the winds. Strong eddy diffusion is not a suitable model parameterization for approximating these light species, especially for extrapolation into the region below 140 km where PVO in-situ data is lacking. Instead, the fully coupled chemical dynamical VTGCM model should be used to improve estimates of densities within the VTS3 empirical model (Hedin et al., 1983) below 140 km.
Over the time period of this NASA grant the PI has helped plan and execute in the PEM-Tropics A field program. He has also helped organize and co-chair three data workshops which have focused on the detailed analysis of PEM-Tropics A data. His direct participation in these analyses has led to his major involvement in 10 manuscripts, 5 of which are in print, 3 in press, and 2 submitted. A complete list of papers is included in the report.
Mineral/melt partition coefficients have been widely used to provide insights into magmatic processes. Olivine is one of the most abundant and important minerals in the lunar mantle and mare basalts. Yet, no systematic olivine/melt partitioning data are available for lunar conditions. We report trace element partition data between host mineral olivine and its melt inclusions in lunar basalts. Equilibrium is evaluated using the Fe-Mg exchange coefficient, leading to the choice of melt inclusion-host olivine pairs in lunar basalts 12040, 12009, 15016, 15647, and 74235. Partition coefficients of 21 elements (Li, Mg, Al, Ca, Ti, V, Cr, Mn, Fe, Co, Y, Zr, Nb, Gd, Tb, Dy, Ho, Er, Tm, Yb and Lu) were measured. Except for Li, V, and Cr, these elements show no significant difference in olivine-melt partitioning compared to the data for terrestrial samples. The partition coefficient of Li between olivine and melt in some lunar basalts with low Mg# (Mg# < 0.75 in olivine, or < ~0.5 in melt) is higher than published data for terrestrial * Corresponding author. Email address: youxue@umich.edu 2 samples, which is attributed to the dependence of DLi on Mg# and the lack of literature DLi data with low Mg#. The partition coefficient of V in lunar basalts is measured to be 0.17 to 0.74, significantly higher than that in terrestrial basalts (0.003 to 0.21), which can be explained by the lower oxygen fugacity in lunar basalts. The significantly higher DV can explain why V is less enriched in evolved lunar basalts than terrestrial basalts. The partition coefficient of Cr between olivine and basalt melt in the Moon is 0.11 to 0.62, which is lower than those in terrestrial settings by a factor of approximately 2. This is surprising because previous authors showed that Cr partition coefficient is independent of fO2. A quasi-thermodynamically based model is developed to correlate Cr partition coefficient to olivine and melt composition and fO2. The lower Cr partition coefficient between olivine and basalt in the Moon can lead to more Cr enrichment in the lunar magma ocean, as well as more Cr enrichment in mantle-derived basalts in the Moon. Hence, even though Cr is typically a compatible element in terrestrial basalts, it is moderately incompatible in primitive lunar basalts, with a similar degree of incompatibility as V based on partition coefficients in this work, as also evidenced by the relatively constant V/Cr ratio of 0.039 ± 0.011 in lunar basalts. The confirmation of constant V/Cr ratio is important for constraining concentrations of Cr (slightly volatile and siderophile) and V (slightly siderophile) in the bulk silicate Moon.
A nearby system of interacting galaxies M81-M82-NGC3077 triplet (D = 3.3 Mpc; Freeman & Madore 1988) has been studied using multi-wavelength observations and numerical simulations to obtain a comprehensive understanding on the dynamics and the consequences of tidal interactions in a group environment. The VLA 12-field Mosaic H I observations of 2 x 1.5 deg. region have revealed a vast array of H I filaments which suggests that the severity and extent of tidal disruptions far exceed the previous estimates. A tidal remnant of the former H I disk of M82 extending up to 30 kpc (in projection) is identified for the first time, and the pervasive effects of the tidal disruption are traced into the inner disk by optical and CO observations, including a kinematic trace of a large scale bar potential (Yun, Ho, & Lo 1992). The H I disk of M81 is traced out to 40 kpc in radius, and a large scale (l approx. 20 kpc) velocity anomaly ('High Velocity Trough'), which may be a remnant of a gaseous collision, is found within the disk of M81. The large H I bridge between M81 and NGC 3077 (van der Hulst 1979) is also found to extend approx. greater than 50 kpc further, bending around NGC 3077, toward M82. The total H I detected in this experiment, 5.6 x 10(exp 9) solar mass, represents the majority of the single-dish flux (Appleton, Davies, & Stephenson 1981) and suggests that the bulk of H I found in the region belongs to the three galaxies and the tidal filaments. The impact and details of the tidal interactions have been further examined through the use of numerical techniques. The 'restricted 3-body' approach was used to simulate the observed distribution of tidal H I streamers connecting the three galaxies, and the success of the simulation is further strengthened by the accurate predictions on the gas kinematics.
A 2-.mu.m fiber Amplified Spontaneous Emission (ASE) source provides a wide emission bandwidth and improved spectral stability/purity for a given output power. The fiber ASE source is formed from a heavy metal oxide multicomponent glass selected from germanate, tellurite and bismuth oxides and doped with high concentrations, 0.5-15 wt. %, thulium oxides (Tm.sub.2O.sub.3) or 0.1-5 wt% holmium oxides (Ho.sub.2O.sub.3) or mixtures thereof. The high concentration of thulium dopants provide highly efficient pump absorption and high quantum efficiency. Co-doping of Tm and Ho can broaden the ASE spectrum.
Ground-based microwave spectroscopy measurements of mesospheric CO and H2O vertical mixing ratio profiles are used to infer vertical mixing rates in the upper mesosphere. The CO and H2O data consistently imply vertical eddy diffusion coefficients in the 70- to 85-km region of 100,000-200,000 sq cm/s during spring through summer at midlatidues. Although chemical acceleration of vertical transport is substantial for O and O3, below the mesopause, the divergences of their associated fluxes are modest, with at most a factor of 2 effect on the concentrations of O and O3 for measured variability in gravity wave activity. Comparison of Solar Mesosphere Explorer (SME) O3 data with model results reinforces the conclusions of slow vertical mixing in the upper mesosphere as a consequence of the reduced HO(x) catalytic loss of odd oxygen. The changes in chemical rate constants recommended by Rusch and Eckman (1985), in conjunction with slow vertical mixing, yield good agreement with SME O3 data. The slow vertical mixing deduced in this study is consistent with upper limits obtained from studies of the mesospheric heat budget and could be construed as evidence for an advectively controlled mesosphere. A comparison of the vertical eddy diffusion coefficients for momentum stresses, constituent transport, and heat transport suggests that the eddy Prandtl number must be of order 10.
We present results of a recently completed effort to design, fabricate, and demonstrate a compact lidar transceiver for coherent-detection lidar profiling of winds. The novel high-energy, 2-micron, Ho:Tm:LuLiF laser technology developed at NASA Langley was employed to permit study of the laser technology currently envisioned by NASA for global coherent Doppler lidar measurement of winds in the future. The 250 mJ, 10 Hz compact transceiver was also designed for future aircraft flight. Ground-based wind profiles made with this transceiver will be presented. NASA Langley is currently funded to build complete Doppler lidar systems using this transceiver for the DC-8 and WB-57 aircraft. The WB-57 flights will present a more severe environment and will require autonomous operation of the lidar system. The DC-8 lidar system is a likely component of future NASA hurricane research. It will include real-time data processing and display, as well as full data archiving. We will attempt to co-fly on both aircraft with a direct-detection Doppler wind lidar system being prepared by NASA Goddard Space Flight Center.