SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
CdCl2 is trigonal omega-like structured and crystallizes in the trigonal R-3m space group. The structure is two-dimensional and consists of three CdCl2 sheets oriented in the (0, 0, 1) direction. Cd2+ is bonded to six equivalent Cl1- atoms to form edge-sharing CdCl6 octahedra. All Cd–Cl bond lengths are 2.68 Å. Cl1- is bonded in a distorted T-shaped geometry to three equivalent Cd2+ atoms.
CdCl2 is trigonal omega-like structured and crystallizes in the triclinic P-1 space group. The structure is two-dimensional and consists of one CdCl2 sheet oriented in the (0, 0, 1) direction. Cd2+ is bonded to six equivalent Cl1- atoms to form edge-sharing CdCl6 octahedra. There are two shorter (2.67 Å) and four longer (2.69 Å) Cd–Cl bond lengths. Cl1- is bonded in a distorted T-shaped geometry to three equivalent Cd2+ atoms.
Cd-excess and CdCl2 treatment effects on Sb-doped CdTe devices
Graphite fibers were intercalated using CdCl2 as a Cl source and Cl2 as carrier gas. Fibers were synthesized with a resistivity-density figure of merit comparable to that of copper. These fibers can withstand practical electrical current densities as high as 54,000 A/sq cm. Their thermal coefficient of resistivity is 0.0016 C, which is approximately 41 percent of those for copper and aluminum.
TCF-21-25048 is a one-year project to quantify the potential attributes of recent NREL inventions where CdTe devices with grain sizes exceeding 100's of microns in lateral dimension can be fabricated using a novel seeded-epitaxial process. A CdSe0.1Te0.9 film is evaporated on commercially available transparent conducting oxide (TCO) where the latter surface roughness (Ra) has been reduced to < 1-nm. After NREL's colossal grain growth (CGG) process, the grain size of this "seed" layer is increased to 100-1000 um. CdTe is then deposited epitaxially resulting in a large-grain CdTe device structure without use of CdCl2. As of this report, we have: Demonstrated the feasibility of using Tec-15 substrates after surface roughness (Ra) reduction (nexTC); Developed reproducible CGG processes for this commercially available substrate; Developed a close-spaced sublimation (CSS) process for CdTe epitaxy using these substrates; Demonstrated that large-grain CdTe films have less sub-band (band tail) absorption than conventional, small-grain CdTe; Demonstrated that large-grain CdTe films (no CdCl2) have carrier lifetimes up to 1.5 ns; Demonstrated that carrier lifetimes in epi-CdTe films (no CdCl2) have comparable lifetimes when compared to the best pX-CdTe films (FSLR) treated with CdCl2; Started making large-grain CdTe devices using CGG templates and epitaxially deposited CdTe.
In state-of-the art polycrystalline CdTe photovoltaics, group-V dopant activation is about 2%. Low activation can create electronic defects and lead to recombination and band tail losses. To develop methods to overcome this limitation, dopant activation was systematically investigated using molecular beam epitaxy (MBE) grown single crystal bilayers of As-doped CdTe on undoped CdTe. Results suggest multiple paths for improved As-activation in polycrystalline CdTe-based devices. It was found that the carrier concentration in this MBE material saturated at ∼3 × 1016 cm−3, with high levels (>50%) of As-activation possible. High activation could be achieved with a post-growth activation temperature of ∼450 °C, when the initial doping level was below the saturation level. However, at typical polycrystalline As incorporation levels (>5 × 1016 cm−3), the excess As is inactive or compensating, requiring elevated temperatures (500–600 °C) to achieve high activation. Oxygen in the annealing ambient was detrimental, while the effect of CdCl2 in the ambient is more case-dependent. A 575 °C activation anneal was combined with a 450 °C CdCl2 treatment to better understand the implications for polycrystalline CdTe. Interestingly, on highly doped samples, processes ending with a high temperature step displayed high activation, while those ending at 450 °C significantly reduced the carrier concentration (with or without CdCl2 in the ambient). Low activation can be restored with another high temperature anneal, allowing reproducible toggling between high and low activation based on the final temperature. Photoluminescence revealed the presence of donor–acceptor pairs in the low activation state that appear to be associated with a compensating defect.
II-VI based thin-film photovoltaics (PV) have experienced substantial commercial success on a foundation of fast large-scale deposition and processing. This type of processing, regardless of material type, nearly always results in small grain (nm to several um diameters) polycrystalline material that, if not for effective grain boundary (GB) and defect passivation, would severely limit PV performance. In the case of CdTe based PV technology, the nearly ubiquitous CdCl2 treatment is used, in part, to passivate the polycrystalline p-type absorber even though Cl is known to (and used to) compensate p-type II-VI materials. Given that VOC is still the most limited performance metric and it can only be improved through higher p-type absorber concentrations, CdCl2 treatments may be holding the technology back. In this talk, we will discuss results related to a process by which small grain CdSeTe material is rapidly transformed into very large grain material (100-1000um diameters, Fig. 1a). This explosive recrystallization, which we have termed colossal grain growth (CGG), occurs by a Cl free process with thin films (<10um) deposited using the same fast deposition techniques the industry has relied on for more than a decade. Our modeling suggests that GB recombination becomes significantly less important at these grain sizes and thus may eliminate the need for a CdCl2 treatment. This result is complimented by previous results of epitaxial growth at high rates on single crystal seed layers. Thin CdSeTe CGG seed layers can be used for rapid epitaxy of CdTe to complete a standard device stack (Fig.1b). This is an optimistic view and the current limitations and challenges related to this process and these materials will also be discussed, including alloy and substrate roughness sensitivity, intragrain material quality, and complex defect chemistry. These challenges are not insignificant but overcoming them may enable a new structural paradigm for thin-film PV.
Advancing optoelectronic and emerging technologies increasingly requires control and design of interfaces between dissimilar materials. However, incommensurate interfaces are notoriously defective and rarely benefit from first-principles predictions, because no explicit atomic-structure models exist. Here, we adopt a bulk crystal structure prediction method to the interface geometry and apply it to SnO2/CdTe heterojunctions without and with the addition of CdCl2, a ubiquitous and beneficial, but abstruse processing step in CdTe photovoltaics. Whereas the direct SnO2/CdTe interface is highly defective, we discover a unique two-dimensional CdCl2 interphase, unrelated to the respective bulk structure. It facilitates a seamless transition from the rutile to zincblende lattices and removes defect-states from the interface bandgap. Implementing the predicted interface electronic structure in device simulations, we demonstrate the theoretical feasibility of bufferless oxide-CdTe heterojunction solar cells approaching the Shockley–Queisser limit. Our results highlight the broader potential of designing atomically thin interlayers to enable defect-free incommensurate interfaces.
Understanding the nature of recombination mechanisms is essential for higher power conversion efficiency in photovoltaic (PV) devices. Here we use a combination of time-resolved terahertz spectroscopy and numerical modeling to determine the bulk Shockley-Read-Hall lifetime and interface and back surface recombination velocities in CdTe thin film stacks. Furthermore, the measurement was facilitated by fabricating wire-grid device structures using conventional laser scribing. Evaluation of a glass/FTO/SnO2/CdS/CdTe stack treated with CdCl2 allowed separation of the CdTe absorber bulk lifetime, 1.6 ns, from the back surface recombination velocity, ~6x10 4 cm/s, and indicated that CdTe/CdS interface recombination velocity had no significant impact on carrier dynamics.
CdCl2CNCl crystallizes in the monoclinic P2_1/m space group. The structure is one-dimensional and consists of two cyanogen chloride molecules and one CdCl2 ribbon oriented in the (0, 1, 0) direction. In the CdCl2 ribbon, Cd2+ is bonded in a square co-planar geometry to four Cl1- atoms. There are two shorter (2.54 Å) and two longer (2.57 Å) Cd–Cl bond lengths. There are two inequivalent Cl1- sites. In the first Cl1- site, Cl1- is bonded in an L-shaped geometry to two equivalent Cd2+ atoms. In the second Cl1- site, Cl1- is bonded in an L-shaped geometry to two equivalent Cd2+ atoms.
CdS films have been prepared by spraying in air solutions of thiourea with either cadmium chloride or cadmium acetate with varying mole ratio and substrate temperature, and subsequently heat treating in oxygen. Substrates included both bare glass or sapphire and transparent conducting oxide-coated sapphire for electrical measurements lateral and transverse to the CdS plane, respectively. Dark resistances of over 10 to the 14th ohms and light-to-dark conductivities of up to 10 to the 7th were obtained using uncoated substrates. The use of Cd(C2H3O2)2 in place of CdCl2 greatly increased the speed of response although with some sacrifice in photoconductivity. Deposition of CdS on ITO-coated surfaces led to greatly reduced dark resistances for the case of CdCl2, but not Cd(C2H3O2)2, presumably due to HCl reaction with the ITO coating in the course of spraying with the former. Ion microprobe analysis detected indium within the CdS films exhibiting low dark resistance. Measurements of the dark and light conductivities at temperatures down to 77 K are given as are the response times for unetched and HCl-etched surfaces.
The effect of high-temperature annealing (HTA) treatments and Cd-excess during the in-situ doping of CdSeTe:Sb is investigated. Optimized treatments eliminate the wurtzite phase from the as-deposited CdSeTe layer, while facilitating Se intermixing and grain size enhancement before CdCl2 treatment. The improved device stack quality results in a VOC improvement of 250 mV. VOC is further improved by tuning the Cd/Sb flux ratio during CdSeTe:Sb deposition. The lowest defect concentration is achieved at Cd/Sb of 1.4:1, which produced the best VOC CdSeTe:Sb cell with VOC = 849mV, despite a decreased carrier concentration due to the harsh CdCl2 treatment.
The impact of high temperature annealing (HTA) treatments on the performance of Sb-doped CdSeTe solar cells containing a CdSe0.25Te0.75/CdTe front stack and a vapor transport (VT) deposited CdTe:Sb absorber was studied. The HTA treatment of the thermally evaporated CdSe0.25Te0.75/CdTe front stack converts the mixed-phase film into a single zinc blende structure through recrystallization of the photo-inactive wurtzite phase. Subsequently, HTA treatment of the full device stack after vapor transport deposition of CdTe:Sb absorber promotes Se-Te intermixing, reduces voids, densifies the full stack and enhances CdTe:Sb grain growth. Comprehensive characterizations revealed that the combined HTA treatments significantly improved film crystallinity, removed the WZ phase in the front stack, enhanced full-stack densification, reduced defect densities, and enhanced carrier dynamics. With HTA treatments, the open-circuit voltage (VOC) of CdSeTe:Sb devices increased from ~ 400 mV to >= 600 mV, and when combined with optimized CdCl2 treatment, VOC reached 849 mV. The net carrier concentrations (NA-ND) of representative devices were NA-ND = 1.5 x 10^15, 1.1 x 10^15, and 3.5 x 10^14 cm-3 for the no-HTA, moderate-HTA, and optimized high-VOC conditions, respectively. Since the highest VOC corresponds to the lowest apparent NA-ND, , which is similar to a Cu-doped-only CdSeTe solar cell (NA-ND ~= 2 x 10^14 cm-3), the data indicate that improved device performance does not result from increased electrically active Sb; instead, it points to structural improvement as the dominant effect of HTA. The findings demonstrate the potential of HTA treatments to improve the structural and electrical properties of CdSeXTe1-X solar cells.
Our previous work has demonstrated that the formation of a penternary cadmium chalcogenide Cd(O,S,Se,Te) region can significantly reduce the front interface recombination in Cd(Se,Te)-based thin-film solar cells. In this work, we have shown that oxygen management during the device fabrication is crucial to form this region. While both the CdS and CdSe layer depositions and the postdeposition CdCl2 treatment should be conducted in the presence of oxygen, the CdTe deposition should be conducted in an oxygen-free atmosphere. Improper oxygen management leads to low device performance due to the formation of a photoinactive Cd(S,Se) region and reduced absorber quality. Additionally, we investigated the carrier transport and collection properties in devices with photoinactive Cd(S,Se) and photoactive Cd(O,S,Se,Te) at the front interface to gain comprehensive understanding of the mechanisms that resulted in improved efficiencies approaching 20%.
The electron density, mobility, bandgap, and band alignment of transparent conducting oxides (TCOs) can be tailored by adjusting composition and stoichiometry, thereby enabling interface engineering for diverse semiconductor applications. For example, solar cell efficiency can change enormously by adjusting TCO properties. At the same time, these TCO properties can shift during the deposition of other layers, anneals, and device operation. An ideal TCO should have tunable but stable electro-optical properties. Here, we deposit SnO 2 , (Mg,Zn)O (MZO), and Ga:(Mg,Zn)O (GMZO) films on glass and measure electro-optical characteristics before and after reducing, inert, oxidizing, and CdCl2 anneals over a range of temperatures. Electron density generally increases in the progression from oxidizing to inert and reducing ambients. SnO 2 is relatively stable compared to MZO but has less flexibility for interface engineering. We investigate GMZO as a similar but more stable alternative to MZO.The addition of Ga to MZO has significant effects on electron density and improves electro-optical stability, which can be advantageous for semiconductor applications. Furthermore, we demonstrate that GMZO can be readily incorporated into solar cells.
The introduction of Se in CdTe solar-cell absorbers has led to multiple beneficial effects in the devices, including an increased short-circuit current and an extended charge-carrier lifetime. A critical manufacturing step of CdSexTe1-x solar cells is CdCl2 annealing at high temperatures, during which Se diffuses through the absorber layer. Understanding the local Se distribution in the absorber and its impact on optical properties of the material is key for the further development of this thin-film solar cell technology. In a multimodal x-ray scanning microscopy approach, we investigated the impact of the annealing temperature of CdSexTe1-x solar cells on the Se distribution and on optical characteristics of the material. For this purpose, we exploited an upgraded x-ray excited optical luminescence (XEOL) detection unit that enables simultaneous spectrally and temporally resolved XEOL mapping at synchrotron facilities that are ideal for studying thin-film solar-cell materials with hard x-rays featuring high penetration depth and lateral resolution.
Development of a new SbCl3-based solution treatment for chloride activation of CdTe-based solar cells is described. Activation was confirmed with CdSeTe:Sb devices exhibiting VOC > 550 mV and JSC > 25 mAcm-2. Treatment optimization showed strong effects of annealing time and temperature on cell properties. Material characterization indicated surface conversion of CdSeTe to CdCl2 and Sb2Te3 with SbCl3 treatment. However, no reaction products were formed with treatment under inert conditions, which was coupled with poor device performance. Drying the SbCl3 films at controlled humidity conditions confirmed that exposure to high relative humidity is critical for CdSeTe activation, through hydrolysis of SbCl3. Mechanistic details of SbCl3 speciation during hydrolysis and annealing to activate CdSeTe are discussed.
Group-V doping can enhance the efficiency of CdTe photovoltaic devices by increasing the open-circuit voltage (Voc), if long lifetimes can be retained and radiative voltage loss can be avoided. In this preliminary study, ex-situ Sb doping via drive-in diffusion improved grain sizes compared to Sb-free films without CdCl2 treatment. Sb doping did not reduce the carrier lifetime for uniform CdSeTe absorbers. Additionally, the CST-air surface recombination decreased with Sb. No potential fluctuations were observed by PL at this doping level. The [Sb] and carrier concentration for this study are not yet measured so the conclusions drawn are all preliminary