Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CYLINDER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1971

Results of a study of Mach number and Reynolds number effects on the crossflow drag characteristics of ogive cylinders and ogive-cylinder-frustum-cylinders at angles of attack to 30 degrees

An analysis was made to determine the effects of Mach number and Reynolds number on the local and total crossflow drag characteristics of ogive-cylinders and ogive-cylinder-frustum-cylinders at angles of the MSFC 14 in TWT and the LTV 4 ft HSWT, and pressure data obtained in the TWT, at Mach numbers 0.14, 0.8, 1.2, and 2.0, and a wide range of Reynolds numbers. Results indicate that the streamwise Reynolds number, VD/nusin alpha, is an important correlation parameter in the subcritical Reynolds number range at imcompressible speeds and that the crossflow Mach number correlates compressibility effects.

Foley, J. E.↗
NASA NTRS1946

Stresses in and General Instability of Monocoque Cylinders with Cutouts I : Experimental Investigation of Cylinders with a Symmetric Cutout Subjected to Pure Bending

Ten 24S-T alclad cylinders of 20-inch diameter, 45- or 58-inch length, and 0.012-inch wall thickness, reinforced with 24S-T aluminum alloy stringers and rings were tested in pure bending. In the middle of the compression side of the cylinders there was a cutout extending over 19 inches in the longitudinal direction, and over an angle of 45 degrees, 90 degrees, or 135 degrees in the circumferential direction. The strain in the stringers and in the sheet covering was measured with metal electric strain gages. The stress distribution in the cylinders deviate considerably from the linear law valid for cylinders without a cutout. The maximum strain measured was about four-thirds of the value calculated from the Mc/I formula when I was taken as the moment of inertia of the cross section of the portion of the cylinder where the cutout was situated. A diagram is presented containing the strain factors defined as the ratios of measured strain to strain calculated with the Mc/I formula. All the 10 cylinders tested failed in general instability. Two symmetric and one antisymmetric pattern of buckling were observed and the buckling load appeared to be independent of the method of manufacture and the length of the cylinder. The buckling load of the cylinders having cutouts extending over 45 degrees, 90 degrees, and 135 degrees was 66, 47, and 31 percent, respectively, of the buckling load of the cylinder without a cutout.

CYLINDERS, MONOCOQUE-BUCKLING↗
NASA NTRS1987

Endwall heat transfer in the junction region of a circular cylinder normal to a flat plate at 30 and 60 degrees from stagnation point of the cylinder

The objective of this experimental study was to investigate the influence of horseshoe vortex on the heat transfer on a flat plate near the base of a protruding cylinder. The partial shock reflection technique was used to produce the flow Mach number of 0.14 which simulated the mean inlet flow Mach number for the first stage vanes of the turbine after combustor. Fast response thin-film platinum heat gages were used to measure the heat transfer flux for radial distances of 0.75, 0.875, 1.0, 1.125 cylinder diameter. For a low Reynolds number of 20,000, r/D = 0.75, and angular location from the stagnation point = 60 deg, the maximum increase in the heat transfer rate with the cylinder was observed to be approximately 460 percent greater than without the cylinder. On the other hand, the increase in the heat flux for a high Reynolds number of 300,000 was approximately 70 percent greater. For the heat gages located along 30 deg and 60 deg angular locations from the stagnation point, the strong effect of the horseshoe vortex was observed in the junction region. The increase in the heat transfer rate depended on the type of boundary layer and on the boundary layer thickness ahead of the cylinder.

Nagamatsu, H. T.↗
NASA NTRS1947

Some Investigations of the General Instability of Stiffened Metal Cylinders VIII : Stiffened Metal Cylinders Subjected to Pure Torsion

An experimental investigation of the general instability of reinforced thin-walled metal cylinders was carried out at the California Institute of Technology. The basic parameters involved were the spacing and sectional properties of the stiffening elements, the wall thickness, and the diameter of the cylinder. An analysis of the experimental data led to a suitable parameter for estimating the general instability stress of reinforced metal cylinders when subjected to pure torsion loading.

CYLINDERS, THIN - TORSION↗
NASA NTRS1948

The Inward Bulge Type Buckling of Monocoque Cylinders IV : Experimental Investigation of Cylinders Subjected to Pure Bending

Eighteen 24S-T alclad cylinders of 20-inch diameter, with skin thickness varying between 0.012 inch and 0.025 inch and length varying between 40.5 inches and 64 inches, were tested in pure bending. They were reinforced with either 16 or 28 stringers and either 5 or 6 rings. One of the purposes of the investigation was to establish the critical value above which failure would occur by general instability and below which panel instability would take place. This value was found to be between 20 and 40 for cylinders with 16 stringers and between 16 and 74 for cylinders with 28 stringers.

LOADS - CYLINDERS, MONOCOQUE↗
NASA NTRS1947

Some Investigations of the General Instability of Stiffened Metal Cylinders IX : Criterions for the Design of Stiffened Metal Cylinders Subject to General Instability Failures

Results are presented of an experimental investigation of the general instability of reinforced thin-walled metal cylinders subjected to pure bending and pure torsion over a range of geometrical quantities and structural sectional characteristics. Based on the experimental results and an existing theory of unstiffened metal cylinders, parameters were evolved which make possible an estimate of the stress at which general instability will occur for any given stiffened metal structure of circular cross section. (author)

STRESSED SKIN - CYLINDERS, METAL↗
NASA NTRS1938

Some Investigations of the General Instability of Stiffened Metal Cylinders V : Stiffened Metal Cylinders Subjected to Pure Bending

This report summarizes the work that has been carried on in the experimental investigation of the problem of general instability of stiffened metal cylinders subjected to pure bending at the C.I.T. This part of the investigation included tests of 46 sheet-covered specimens. The most significant result was the determination of a new design parameter for the case of a stiffened metal cylinder subjected to pure bending.

LOADS-CYLINDERS, MONOCOQUE↗
NASA NTRS1946

Cylinder-temperature correlation of a single-cylinder liquid-cooled engine

An analysis based on nonboiling forced-convection heat-transfer theory is made of the cooling processes in liquid-cooled engine cylinders. Semiempirical equations that relate the average head and barrel temperatures with the primary engine and coolant parameters are derived. A correlation method based on these equations is applied to data obtained from previously reported investigations, which were conducted over large ranges of engine and coolant conditions with two liquid-cooled cylinders using water and various aqueous ethylene glycol solutions as coolants. Upon evaluation of empirical factors, an equation for the cylinder-head temperature as a function of the engine operating conditions and the flow rate, temperature, and physical properties of the coolants is obtained, which represents the data with good accuracy.

Pinkel, Benjamin↗
NASA NTRS1943

Some Investigations of the General Instability of Stiffened Metal Cylinders IV : Continuation of Tests of Sheet-covered Specimens and Studies of the Buckling Phenomena of Unstiffened Circular Cylinders

This is the fourth of a series of reports covering an investigation of the general instability problem by the California Institute of Technology. The first five reports of this series cover investigations of the general instability problem under the loading conditions of pure bending and were prepared under the sponsorship of the Civil Aeronautics Administration. The succeeding reports of this series cover the work done on other loading conditions under the sponsorship of the National Advisory Committee for Aeronautics. This report is to deal primarily with the continuation of tests of sheet-covered specimens and studies of the buckling phenomena of unstiffened circular cylinders.

CYLINDERS, STEEL↗
NASA NTRS1943

Some Investigations of the General Instability of Stiffened Metal Cylinders VI : Stiffened Metal Cylinders Subjected to Combined Bending and Transverse Shear

This is the sixth of a series of reports covering an investigation of the general instability problem by the California Institute of Technology. The first five reports of this series cover investigations of the general instability problem under the loading conditions of pure bending and were prepared under the sponsorship of the Civil Aeronautics Administration. This report and the succeeding reports of this series cover the work done on other loading conditions under the sponsorship of the National Advisory Committee for Aeronautics. This report summarizes the work that has been carried on in the experimental investigation of the problem of general instability of stiffened metal cylinders subjected to combined bending and transverse shear at the C.I.T. This part of the investigation includes tests on 55 sheet-covered specimens.

TESTING MACHINES↗
NASA NTRS1972

Results of a study of Mach number and Reynolds number effects on the lee side vortex flow field characteristics of an ogive-cylinder-frustum-cylinder at angles of attack to 25 degrees, volume 1

An experimental program was conducted to survey the lee side vortex flow field about an ogive-cylinder-frustum-cylinder at angles of attack to 25 degrees for two Reynolds numbers at Mach number 0.8, and one Reynolds number at Mach number 1.96. The data were obtained using miniature 5-port conical pressure probes calibrated for angle of attack and roll angle over a Mach number range of 0.6 to 3.0. The results are presented here as local flow field properties and circulation strengths for various body stations.

Foley, J. E.↗
NASA NTRS1972

Results of a study of Mach number and Reynolds number effects on the lee side vortex flow field characteristics of an ogive-cylinder-frustum-cylinder at angles of attack to 25 degrees. Volume 2: Appendix

A listing of the data reduction computer program output for the analysis of the lee side vortex flow about an ogive-cylinder-frustum-cylinder is presented. A computed local flow property for the flow field location array at a specific body station and freestream condition is listed. Significant local flow properties are computed. The local circulation strengths in the radial and circumferential directions are analyzed.

Foley, J. E.↗
NASA NTRS1943

Some Investigations of the General Instability of Stiffened Metal Cylinders VII : Stiffened Metal Cylinders Subjected to Combined Bending and Torsion

This report summarizes the work that has been carried on in the experimental investigation of the problem of the general instability of stiffened metal cylinders subjected to combined bending and torsion at the C.I.T. This part of the investigation included tests on 26 sheet-covered specimens. An interaction curve for the case of combined bending and torsion is presented. The results of tests of 17 specimens subjected to pure torsion are also given.

CYLINDERS, METAL - INSTABILITY↗