Curing behavior, chain dynamics, and microstructure of high Tg thiol-acrylate networks with systematically varied network heterogeneity
Explore the source record for details and available documents.
99 GENERAL AND MISCELLANEOUS↗
SEARCH · Engineering Papers
Results for “CURING”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Ettringite-Related Dimensional Stability of CO 2 -Cured Portland Cement Mortars
Carbonation curing, where cement is cured in a CO 2 -rich environment, is an emerging technology in the precast industry that promotes CO 2 sequestration in construction materials. It demonstrates good promise for enhancing material strength development, chemical resistance and manufacturing sustainability. A critically important but little studied aspect of carbonation curing is the dimensional stability of the cured materials, which poses a significant impact on longevity of cement-based materials and structures. In this study, we propose to use carbonation curing to substitute the conventional energy-intensive steam curing and time-consuming moisture curing, and examine the dimensional stability of Portland cement mortars manufactured by different curing approaches. The common pathology in precast concrete that potentially creates undesirable expansions, known as Delayed Ettringite Formation (DEF), is particularly investigated. Four curing approaches were examined including moist, steam (maximum temperature at 85°C to purposefully induce DEF), combined steam-carbonation, and carbonation curing in which steam curing was used to verify favorable cement chemistry for DEF and to indicate DEF onset timing. It was found that, among the four curing approaches designed in this study, the carbonation-cured mortars demonstrated the lowest expansion (~0%) whereas the steam-cured mortars showed the highest (>0.6%) after 500 days of storage in saturated limewater. Mortar expansion after the combined steam-carbonation curing (~0.1%) was lower than that of steam curing, but remained higher with respect to the moisture-cured reference. Here, the mineral ettringite was detected at 500 days after all curing approaches. However, larger ettringite crystal size (5-10 μm) with greater dispersion was observed via scanning electron microscopy after steam curing in reference to carbonation curing (< 5 μm). Additionally, the calcium carbonate precipitated by CO 2 carbonation was found to participate in the post-carbonation hydration to promote formation of monocarboaluminate and hemicarboaluminate, which stabilize ettringite and potentially lead to a secondary densification of the mortar microstructure.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Compositional effects on cure kinetics, mechanical properties and printability of dual-cure epoxy/acrylate resins for DIW additive manufacturing
Interest in 3D printing of thermoset resins has increased significantly in recent years. One approach to additive manufacturing of thermoset resins is printing dual-cure resins with direct ink write (DIW). Dual-cure resins are multi-component resins which employ an in situ curable constituent to enable net-shape fabrication while a second constituent and cure mechanism contribute to the final mechanical properties of the printed materials. In this work, the cure kinetics, green strength, printability, and print fidelity of dual-cure epoxy/acrylate thermoset resins are investigated. Resin properties are evaluated as a function of acrylate concentration and in situ UV exposure conditions. The acrylate cure kinetics are probed using photo-differential scanning calorimetry and the impacts of resin composition and UV cure profile on the acrylate extent of conversion are presented. Continuous and pulsed UV cure profiles are shown to affect total conversion due to variances in radical efficiency at different UV intensities and acrylate concentrations. The effects of acrylate concentration on the kinetics of the epoxy thermal cure and the final mechanical properties are also investigated using dynamic mechanical analysis and three-point bend measurements. The glass transition temperature is dependent on formulation, with increasing acrylate content decreasing the T g . However, the room temperature shear moduli, flexural moduli, strength, strain-to-failure, and toughness values are relatively independent of resin composition. The similarity of the final properties allows for greater flexibility in resin formulation and in situ cure parameters, which can enable the printing of complex parts that require high green strength. We found that the in situ UV print intensities and exposure profiles that are necessary to achieve the best print quality are not, in most cases, the conditions that maximize conversion of the acrylate network. Lastly, this highlights the importance of developing optimized resin compositions which enable complete cure of the acrylate network by promoting acrylate dark cure or thermal cure.
36 MATERIALS SCIENCE↗
Residual Stress Developed During the Cure of Thermosetting Polymers: Optimizing Cure Schedule to Minimize Stress
When thermosetting polymers are used to bond or encapsulate electrical, mechanical or optical assemblies, residual stress, which often affects the performance and/or reliability of these devices, develops within the structure. The Thin-Disk-on-Cylinder structural response test is demonstrated as a powerful tool to design epoxy encapsulant cure schedules to reduce residual stress, even when all the details of the material evolution during cure are not explicitly known. The test's ability to (1) distinguish between cohesive and adhesive failure modes and (2) demonstrate methodologies to eliminate failure and reduce residual stress, make choices of cure schedules that optimize stress in the encapsulant unambiguous. For the 828/DEA/GMB material in the Thin-Disk-on-Cylinder geometry, the stress associated with cure is significant and outweighs that associated with cool down from the final cure temperature to room temperature (for measured lid strain, Iε cure I > Iε thermal I). The difference between the final cure temperature and the temperature at which the material gels, T f - T gel , was demonstrated to be a primary factor in determining the residual stress associated with cure. Increasing T f - T gel leads to a reduction in cure stress that is described as being associated with balancing some of the 828/DEA/GMB cure shrinkage with thermal expansion. The ability to tune residual stress associated with cure by controlling T f - T gel would be anticipated to translate to other thermosetting encapsulation materials, but the times and temperatures appropriate for a given material may vary widely.
36 MATERIALS SCIENCE↗
Cement stress and microstructure evolution during curing in semi-rigid high-pressure environments
The process of cement slurry curing into a solid has a direct effect on the initial state of stress in a composite concrete and steel structure. Failure models for critical infrastructure and wellbores could benefit from measurements of this initial stress because it greatly influences structural performance. Here, we present measurements of the initial stress state (total stress, effective stress, and pore pressure) of multiple cement formulations cured under a high-pressure of 40 MPa within a semi-rigid steel pipe. Our results show that cements cured in this restrained environment exhibit dense microstructures with low permeability (nano-Darcy), develop an anisotropic stress state greater than zero and less than the curing pressure, and undergo a staged curing process where hydration and mechanical behaviors evolve from a slurry into a pre-stressed porous medium. Both drained and undrained scenarios were investigated, revealing a feedback from the semi-rigid boundary towards improved cement performance.
36 MATERIALS SCIENCE↗
Ensemble cure kinetics network (ECK-Net): A method to derive cure kinetics of thermosetting resin
This paper introduces an Ensemble Cure Kinetics Network (ECK-Net), a neural network (NN)–based framework for modeling the cure kinetics of thermosetting resins within a phenomenological context. ECK-Net replaces traditional analytic models, which require extensive chemical insight and multiple isothermal/non-isothermal experiments, with a data-driven surrogate that maps nonlinear relationships between temperature, degree of cure, and reaction rate from differential scanning calorimetry data. The proposed approach predicts input-dependent kinetic coefficients of a generalized nth-order reaction equation rather than reaction rates directly, enabling a single unified model to represent various epoxy systems without relying on iso-conversional analysis or predefined functional forms. To ensure robustness, multiple independently trained networks under different random initializations are blended through an ensemble strategy, effectively mitigating the stochastic variability inherent to neural networks. The framework is validated using experimental datasets from multiple resin systems, including aerospace-grade materials (Toray 3900-2, Cycom 5320-1, and Hexcel 8552) and a windmill-grade resin (RIMR 035c). The model accurately reproduces the temporal evolution of the degree of cure under manufacturers’ recommended cure cycles across all tested resins systems, yielding Pearson’s correlation coefficients of 0.992, 0.994, 0.993, 0.997, respectively. To demonstrate process-level applicability, the trained network was implemented within the Abaqus environment to simulate out-of-autoclave (OOA) curing process of the CFRP panel composed of Toray T830H-6K/3900-2D prepreg. The simulation results showed excellent agreement with experimental temperature response (maximum peak temperature, simulation: 189.6 °C, experiment: 188.5 °C) and the final degree of cure (simulation: 0.948, experiment: 0.960 ± 0.013), confirming ECK-Net’s capability as a reliable alternative to conventional cure kinetics modeling methods.
Composite curing↗
Polymerization-Induced Phase Separation in Rubber-Toughened Amine-Cured Epoxy Resins: Tuning Morphology from the Nano- to Macro-scale
Explore the source record for details and available documents.
99 GENERAL AND MISCELLANEOUS↗
Curing agent for polyepoxides and epoxy resins and composites cured therewith
A curing for a polyepoxide is described which contains a divalent aryl radical such as phenylene a tetravalent aryl radical such as a tetravalent benzene radical. An epoxide is cured by admixture with the curing agent. The cured epoxy product retains the usual properties of cured epoxides and, in addition, has a higher char residue after burning, on the order of 45% by weight. The higher char residue is of value in preventing release to the atmosphere of carbon fibers from carbon fiber-epoxy resin composites in the event of burning of the composite.
Serafini, T. T.↗
Characterization of the relationship of the cure cycle chemistry to cure cycle processing properties
Dynamic Dielectric measurements made over a wide range of frequency provide a sensitive and convenient means for monitoring the cure process in thermosets and thermoplastics. The measurement of dielectric relaxation is one of only a few instrumental techniques available for studying molecular properties in both the liquid and solid states. Furthermore, it is probably the only convenient experimental technique for studying the polymerization process of going from a monomeric liquid of varying viscosity to a crosslinked, insoluble, high temperature solid. The objective of the research is to develop on-line dielectric instrumentation for quantitative nondestructive material evaluation and closed loop smart cure cycle control. The key is to relate the chemistry of the cure cycle process to the dielectric properties of the polymer system by correlating the time, temperature, and frequency dependent dielectric measurements with chemical characterization measurements. Measurement of the wide variation in magnitude of the complex permittivity with both frequency and state of cure, coupled with chemical characterization work, have been shown in the laboratory to have the potential to determine: resin quality, composition and age; cure cycle window boundaries; onset of flow and point of maximum flow; extent of and completion of reaction; evolution of volatiles; T sub g; and, crosslinking and molecular weight buildup.
Kranbuehl, D. E.↗
Development of reactive MgO-based Engineered Cementitious Composite (ECC) through accelerated carbonation curing
Not provided.
Construction & Building Technology↗
Carbon fiber/epoxy vitrimer composite patch cured with bio‐based curing agents for one‐step repair metallic sheet and its recyclability
Abstract Vitrimers have gained a great deal of attention from researchers, yet research on its application is still lacking. This study, a novel bio‐based vitrimer was developed from epoxy (EP) and bio‐based curing agents, that is, cashew nut shell liquid (CNSL) and citric acid (CA), and then reinforced by carbon fiber. The vitrimers with different ratios of acid to epoxy (R ratio) at 0.30–0.40 contained ester and ether linkages. All EP/CA/CNSL vitrimers showed the stress relaxation over 70–100°C due to transesterification. The vitrimers were applied as polymer matrices for the carbon fiber composites and then used as repair patches. By using the carbon fiber‐reinforced vitrimer with the R ratio of 0.30, patch repair on a damaged alloy sheet revealed that approximately 98% of the tensile strength of the damaged alloy sheet was recovered. The vitrimer can be dissolved from carbon fiber composite to recover carbon fiber. The recovered carbon fiber retained good tensile strength compared to the pristine composite. Based on this study, the EP/CA/CNSL vitrimers showed the comparable thermomechanical properties with the epoxy vitrimer cured by the petroleum‐based curing agent. The vitrimer composite patch could therefore be an alternative new repair method to extend the service life of damaged structures.
Lorwanishpaisarn, Narubeth↗
Modeling the curing process of thick-section autoclave cured composites
Temperature gradients are significant during cure of large area, thick-section composites. Such temperature gradients result in nonuniformly cured parts with high void contents, poor ply compaction, and variations in the fiber/resin distribution. A model was developed to determine the temperature distribution in thick-section autoclave cured composites. Using the model, long with temperature measurements obtained from the thick-section composites, the effects of various processing parameters on the thermal response of the composites were examined. A one-dimensional heat transfer model was constructed for the composite-tool assembly. The governing differential equations and associated boundary conditions describing one-dimensional unsteady heat-conduction in the composite, tool plate, and pressure plate are given. Solution of the thermal model was obtained using an implicit finite difference technique.
Loos, A. C.↗
Photo-Curing: UV Radiation curing of polymers
The Polymers Branch of the Materials Division is dedicated to the development of high-performance for a variety of applications. Areas of significant interest include high- temperature polymers, low density, and high strength insulating materials, conductive polymers, and high density polymer electrolytes. This summer our group is working diligently on a photo-curing project. There is interest in the medical community feel the need for a new and improved balloon that will be used for angioplasty (a form of heart surgery). This product should maintain flexibility but add many other properties. Like possibly further processability and resistance to infection. Our group intends on coming up with this product by using photo-enolization (or simply, photo-curing) by Diels-Alder trapping. The main objective was to synthesize a series of new polymers by Diels-Alder cycloaddition of photoenols with more elastomeric properties. Our group was responsible for performing the proper photo-curing techniques of the polymers with diacrylates and bismaleimides, synthesizing novel monomers, and evaluating experimental results. We attempted to use a diacrylate to synthesize the polymer because of previous research done within the Polymers Branch here at NASA. Most acrylates are commercially available, have more elastometric properties than a typical rigid aromatic structure has and they contain ethylene oxides in the middle of their structure that create extensive flexibility. The problem we encountered with the acrylates is that they photo chemically and thermally self polymerize and create diradicals at low temperatures; these constraints caused a lot of unnecessary side reactions. We want to promote solely, diketone polymerization because this type of polymerization has the ability to cause very elastic polymers. We chose to direct our attention towards the usage of maleimides because they are known for eliminating these unnecessary side reactions.
Inman, Christina A.↗
Post-print UV curing method for improving the mechanical properties of prototypes derived from two-photon lithography [A post-print UV curing method for improving the mechanical properties of prototypes derived from two-photon polymerization]
Here, two photon polymerization (TPP) is a precise, reliable, and increasingly popular technique for rapid prototyping of micro-scale parts with sub-micron resolution. The materials of choice underlying this process are predominately acrylic resins cross-linked via free-radical polymerization. Due to the nature of the printing process, the derived parts are only partially cured and the corresponding mechanical properties, i.e. modulus and ultimate strength, are lower than if the material were cross-linked to the maximum extent. Herein, post-print curing via UV-driven radical generation, is demonstrated to increase the overall degree of cross-linking of low density, TPP-derived structures.
36 MATERIALS SCIENCE↗
Limited Characterization of Wind Turbine Adhesives [EPIKOTE Resin MGS BPR 135G3/EPIKURE Curing Agent MGS RIMH 134 (H134i) and MGS BP20/EPIKURE Curing Agent MGS BPH 20 (rework adhesive)] and Root Insert Exterior Surface.
The National Rotor Testbed (NRT) is a wind turbine blade research program in the Sandia National Laboratories (SNL) Wind Department that has developed a new blade design. Each blade includes bonded-in, threaded metal root inserts that enable the blades to be bolted onto the wind turbine hub. Prior to installing the flight blades on the turbine, root insert strength verification tests exhibited a subset of failures below the design load on one (NRT-02) of four blades. As part of a root cause analysis for the failures, this work analyzes "scraps" of the epoxy adhesive used to bond the metal inserts into the blade and uses surface topography and x-ray fluorescence (XRF) measurements to characterize the exterior surface of the root insert. Samples were taken from inserts that exhibited both high and low loads at failure, as well as some "control inserts" to monitor the state of the surface throughout the manufacturing process. Differences in the calorimetric response of the adhesive from the separate root inserts are apparent but none of them appear to relate to the pull load required to dislodge the inserts. Two takeaways of note include: In the way that the adhesive is processed, it does not reach full cure; and, Something occurred to sample#10 such that the fully-cured adhesive has a significantly lower T g .
17 WIND ENERGY↗
Characterization of the relationship of the cure cycle chemistry to cure cycle processing properties
Dynamic dielectric analysis (DDA) is used to study curing polymer systems and thermoplastics. Measurements are made over a frequency range of six decades. This wide range of frequencies increases the amount of information which can be obtained. The data is analyzed in terms of the frequency dependence of the complex permittivity epsilon sup *, specific conductivity sigma (ohm/cm) and the relaxation time tau, parameters which are characteristic of the cure state of the material and independent of the size of the sample.
Kranbuehl, D. E.↗
Curing the Divergence in Time-Dependent Density Functional Quadratic Response Theory
While time-dependent density functional theory has emerged as a method of choice for computing electronic spectra and response of molecules and materials, its reliability is hindered by the adiabatic approximation that is commonly made. In this work, we address one problematic aspect that arises from this approximation: an incorrect pole structure in the quadratic response function, leading to unphysical divergences in excited state-to-state transition probabilities and hyperpolarizabilties. We find the form of the exact quadratic response kernel and derive a practical and accurate approximation that cures the divergence. Here, we demonstrate our results on excited state-to-state transition probabilities of a model system and of the LiH molecule.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Structure-to-property relationships in addition cured polymers. 4: Correlations between thermo-oxidative weight losses of norbornenyl cured polyimide resins and their composites
Relationships are identified between the thermo-oxidative stability (TOS) at 316 C of a wide variety of PMR (polymerization of monomeric reactants) addition cured polyimide resins and their corresponding graphite fiber composites. Weight loss results at 316 C confirmed the expected relationship of increasing aliphatic endcap content with decreasing TOS. Moreover, the resin TOS study also showed an unexpected linear correlation of decreasing weight loss to increasing ratio of benzylic diamine to aliphatic endcap in the range of the stoichiometries studied. Only after long term 316 C aging does the dianhydride used with the benzylic diamines become an additional factor in influencing the amount of PMR resin and composite weight losses. Also, the benzylic systems consistently showed much lower resin and composite weight losses at 316 C than the corresponding nonbenzylic norbornenyl resins and composites, except when the nonbenzylic diamine monomer does not contain a connecting group. Instead, this diamine resulted in a 316 C resin and composite weight loss that was only competitive with benzylic type diamines. Results show excellent correlation between TOS of all graphite fiber PMR composites and resins.
Alston, William B.↗