Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “COMBUSTION EFFICIENCY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1954

A flow calorimeter for determining combustion efficiency from residual enthalpy of exhaust gases

A flow calorimeter for determining the combustion efficiency of turbojet and ram-jet combustors from measurement of the residual enthalpy of combustion of the exhaust gas is described. Briefly, the calorimeter catalytically oxidizes the combustible constituents of exhaust-gas samples, and the resultant temperature rise is measured. This temperature rise is related to the residual enthalpy of combustion of the sample by previous calibration of the calorimeter. Combustion efficiency can be calculated from a knowledge of the residual enthalpy of the exhaust gas and the combustor input enthalpy. An accuracy of +-0.2 Btu per cubic foot was obtained with prepared fuel-air mixtures, and the combustion efficiencies of single turbojet combustors measured by both the flow-calorimeter and heat-balance methods compared within 3 percentage units. Flow calorimetry appears to be a suitable method for determining combustion efficiencies at high combustor temperatures where ordinary thermocouples cannot be used. The method is fundamentally more accurate than heat-balance methods at high combustion efficiencies and can be used to verify near-100-percent efficiency data.

Evans, Albert↗
NASA NTRS1973

Evaluation of magnesium-aluminum eutectic to improve combustion efficiency in low burning rate propellants

A previous investigation indicated that combustion efficiency of low burning-rate propellants could be improved if the aluminum fuel was replaced by aluminum particles coated with a magnesium-aluminum eutectic alloy (ALCAL). The purpose of the present investigation was to evaluate the possibility of improving the combustion efficiency of these propellants by admixing the eutectic with the aluminum rather than coating the aluminum. Tests of three propellants similar in every respect except for the metal fuel were conducted in test motors with 4.54 kg (10 lbm) of propellant. The first propellant used aluminum fuel; the second contained aluminum admixed with magnesium-aluminum eutectic; the third used ALCAL. The test results show the the admixed fuel gave better low burning-rate combustion efficiency than the other two. The test results also showed that the ALCAL was deficient in that much, if not all, of the coating material could be found as the fine particles in a bimodal mix of aluminum and eutectic. The combustion efficiency of low burning-rate aluminized propellants can be significantly improved by mixing a small amount of magnesium-aluminum alloy with the aluminum fuel.

Northam, B. G.↗
NASA NTRS1984

Comparison of combustion efficiencies for ramjet engines

Four different combustion efficiencies commonly used for assessing ramjet engines are compared. The mixture ratios cover a range from stoichiometric to an equivalence ratio of 0.2, and the polyethylene/air propellant system is used. The ratio of effective to ideal temperature rise is taken as reference efficiency. As might be expected, major differences can be observed near stoichiometric and down to equilvalence ratios of 0.5. These are quantitatively demonstrated.

Bergmann, J. W.↗
NASA NTRS1950

Combustion efficiency and altitude operational limits of three liquid hydrocarbon fuels having high volumetric energy content in a J33 single combustor

Combustion efficiency and altitude operational limits were determined in a J33 single combustor for AN-F-58 fuel and three liquid hydrocarbon fuels having high volumetric energy content (decalin, tetralin, and monomethylnaphthalene) at simulated altitude and combustor inlet-air conditions. At the conditions investigated, the combustion efficiency for the four fuels generally decreased with an increase in volumetric energy content. The altitude operational limits for decalin and tetralin fuels were higher than for AN-F-58 fuel; monomethylnaphthalene fuel gave the lowest altitude operational limit.

Stricker, Edward G↗
NASA NTRS1947

Performance Investigation of TG-180 Combustor: I - Instrumentation, Altitude Operational Limits and Combustion Efficiency

A brief investigation has been made of the performance of a single combustor of the TG-180 turboJet engine to determine (a) the altitude operational limits of the engine for two fuels (AN-F-32 and AN-F-28), (b) combustion efficiencies at various simulated conditions of altitude and engine speeds, (c) combustion-outlet temperature distribution for several altitudes at constant engine speed, and (d) the combustor total pressure drop The limits with AN-83-F-32 fuel were found to be approximately 60,000 feet for an engine speed of 6000 rpm and approximately 38,000 feet for an engine speed of 1000 rpm. The results indicated that the altitude operational limits with AN-F-32 fuel are higher over the largest part of the engine-speed range than with AN-F-28 fuel, A combination efficiency of 22 percent was obtained at rated engine speed (7600 rpm) and an altitude of 20,000 feet with AN-F-32 fuel. A change in altitude from 20,000 tm 60,000 feet showed a 20-percent decrease in combustion efficiency while the engine was operating at 760G rpm whereas, at an engine speed of 4000 rpm a change of altitude from 10,000 to 40,000 feet showed a 52-percent decrease in combustion efficiency .

Zettle, Eugene V.↗
NASA NTRS1950

Altitude Test Chamber Investigation of Performance of a 28-inch Ram-jet Engine II : Effects of Gutter Width and Blocked Area on Operating Range and Combustion Efficiency

Altitude-test-chamber investigation of effects of flame-holder blocked area and gutter width on performance of 28-inch diameter ram jet at simulated flight Mach number of 2.0 for altitudes from 40,000 to 55,000 feet was conducted at NACA Lewis laboratory. Ten flame holders investigated covered gutter widths from 1.00 to 2.50 inches and blocked areas from 40.5 to 62.0 percent of combustion-chamber area. Gutter width did not appreciably affect combustion efficiency. Increase in blocked area from 40 to 62 percent resulted in 5- to 10-percent increase in combustion efficiency. Increasing gutter width resulted in improvement in fuel-air-ratio operating range.

Shillito, T B↗
NASA NTRS1976

Simulation of fluidized bed combustors. I - Combustion efficiency and temperature profile

A chemical engineering analysis is made of fluidized-bed combustor (FBC) performance, with FBC models developed to aid estimation of combustion efficiency and axial temperature profiles. The FBC is intended for combustion of pulverized coal and a pressurized FBC version is intended for firing gas turbines by burning coal. Transport phenomena are analyzed at length: circulation, mixing models, drifting, bubble wake lift, heat transfer, division of the FB reactor into idealized mixing cells. Some disadvantages of a coal FBC are pointed out: erosion of immersed heat-transfer tubing, complex feed systems, carryover of unburned coal particles, high particulate emission in off-streams. The low-temperature bed (800-950 C) contains limestone, and flue-gas-entrained SO2 and NOx can be kept within acceptable limits.

Horio, M.↗
NASA NTRS1957

Relation of Turbojet and Ramjet Combustion Efficiency to Second-Order Reaction Kinetics and Fundamental Flame Speed

Theoretical studies of the turbojet and ramjet combustion process are summarized and the resulting equations are applied to experimental data obtained from various combustor tests. The theoretical treatment assumes that one step in the over-all chain of processes which constitute jet-engine combustion is sufficiently slow to be the rate-controlling step that determines combustion efficiency.

Childs, J Howard↗
NASA NTRS1991

Combustion efficiency determined from wall pressure and temperature measurement in a Mach 2 combustor

A study of transverse hydrogen injection behind a rearward facing step in a Mach 2 airflow was conducted to determine the combustion efficiency and the combustor/inlet interactions at the low temperature lean-mixture operational end of a scramjet combustor model. The fuel was injected at sonic conditions into the electrically heated airstream, which was maintained at 850 K or below. The static pressure delivered at the entrance of the combustor ranged between 0.25 to 0.5 atm. Injector configurations included single and staged injectors placed at 3 or 3-and-7 step-heights downstream of the step, respectively, with injector diameters of 1, 1.5, and 2 mm. Ignition was achieved by initially unstarting the test section. The constant area combustor and the low initial temperatures caused thermal choking and upstream interaction to occur at very low equivalence ratios. Typically, most of the fuel was burned in the recirculation region behind the step and around the jets. The effects of initial conditions (temperature and pressure), fuel-to-air dynamic pressure ratio, and boundaries (thermal vs adiabatic) are presented.

Segal, Corin↗
DOE OSTI2024

Active Palladium Structures on Ceria Obtained by Tuning Pd–Pd Distance for Efficient Methane Combustion

Efficiently removing/converting methane via methane combustion imposes challenges on catalyst design: how to design local structures of a catalytic site so that it has both high intrinsic activity and atomic efficiency? By manipulating the atomic distance of isolated Pd atoms, herein we show that the intrinsic activity of Pd catalysts can be significantly improved for methane combustion via a stable Pd 2 structure on a ceria nanorod support. Guided by theory and confirmed by experiment, we find that the turnover frequency (TOF) of the Pd 2 structure with the Pd–Pd distance of 2.99 Å is higher than that of the Pd 2 structure with the Pd–Pd distance of 2.75 Å; at least 26 times that of ceria supported Pd single atoms and 4 times that of ceria supported PdO nanoparticles. The high intrinsic activity of the 2.99 Å Pd–Pd structure is attributed to the conductive local redox environment from the two O atoms bridging the two Pd 2+ ions, which facilitates both methane adsorption and activation as well as the production of water and carbon dioxide during the methane oxidation process. In conclusion, this work highlights the sensitivity of catalytic behavior on the local structure of active sites and the fine-tuning of the metal–metal distance enabled by a support local environment for guiding the design of efficient catalysts for reactions that highly rely on Pt-group metals.

36 MATERIALS SCIENCE↗
NASA NTRS1985

Combustion efficiency of a premixed continuous flow combustor

Exhaust gas temperature, velocity, and composition measurements at various radial locations at the combustor exit are presented for a swirling-flow continuous combustor of a confined concentric jet configuration operating on premixed propane or methane and air. The main objective of the study is to determine the effect of fuel substitution and of changes in outer flow swirl conditions on the combustor performance. It is found that there is no difference in observed properties for propane and methane firing; the use of either of the fuels results in nearly the same exit temperature and velocity profiles and the same efficiency for a given operating condition. A mechanism for combustion is proposed which explains qualitatively the changes in efficiency and pollutant emissions observed with changing swirl.

Anand, M. S.↗