Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CHEMICAL PREPARATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Phase evolution during reactive flash sintering of Li 6.25 Al 0.25 La 3 Zr 2 O 12 starting from a chemically prepared powder

Here, reactive flash sintering (RFS) of a chemically prepared multiphase precursor powder was performed to fabricate Li 6.25 Al 0.25 La 3 Zr 2 O 12 (Al-LLZO) ceramics. This approach allowed for obtaining single-phase dense samples in a remarkably short processing time of 30 s, at a furnace temperature of 600 °C, with an electric field of 50 V cm -1 and a current limit of 150 mA mm -2 . The ceramics display high bulk conductivity of 0.18 mS cm -1 at room temperature. Furthermore, phase evolution is studied by in-situ X-ray diffraction during: i) conventional heating and ii) RFS under current rate mode. As expected, the intermediate phases progressively dissolved into the Al-LLZO matrix by conventional heating. On the other hand, RFS promoted the growth of the intermediate La 2 Zr 2 O 7 , an effect that was overcome by the thermally driven formation of Al-LLZO at higher temperatures. The observed different reaction pathway suggests that RFS can be used for stabilizing phases that are not thermodynamically favored upon conventional heating.

36 MATERIALS SCIENCE↗

Direct-write, chemically-prepared temperature insensitive dielectrics.

Development of high energy density dielectrics with low temperature coefficients of capacitance that are systems integrable are needed for extreme environment, defense and automotive applications. The synthesis of high purity chemically prepared Ca(Zr,Ti)O3 powders is described and has resulted in the lowering of conventional firing temperatures by over 100 C. Direct write aerosol spray deposition techniques have been used to fabricate high quality single layer and multilayer capacitors from these powders. The dielectric constants of the direct write capacitors are equivalent to those of fired bulk ceramics. Our presentation emphasizes the synthesis, phase evolution and microstructure development that has resulted in dielectrics with energy densities in excess of 3 J/cm3 with less than 1% change in dielectric constant over a 200 C temperature range.

36 MATERIALS SCIENCE↗

Long-term {alpha}- and spontaneous fission measurement of a Rf/Db sample chemically prepared in a {sup 48}Ca on {sup 243}Am experiment

Results from long-term measurements of a chemically separated Db/Rf sample prepared from the products of a {sup 48}Ca on {sup 243}Am irradiation are presented. The sample with the highest spontaneous fission activity out of eight samples produced in the course of chemical experiments performed in 2004 was selected for these measurements. We conclude that there is no evidence for SF-decay originating from heavy actinide isotopes in this sample. Hence, it is appropriate to assign the SF-events observed in this experiment to decay products of {sup 288}115.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Automated Radioanalytical System Incorporating Microwave-Assisted Sample Preparation, Chemical Separation, and Online Radiometric Detection for the Monitoring of Total 99Tc in Nuclear Waste Processing Streams

An automated fluidic instrument is described that rapidly determines the total 99Tc content of aged nuclear waste samples, where the matrix is chemically and radiologically complex and the existing speciation of the 99Tc is variable. The monitor links microwave-assisted sample preparation with an automated anion exchange column separation and detection using a flow-through solid scintillator detector. The sample preparation steps acidify the sample, decompose organics, and convert all Tc species to the pertechnetate anion. The column-based anion exchange procedure separates the pertechnetate from the complex sample matrix, so that radiometric detection can provide accurate measurement of 99Tc. We developed a preprogrammed spike addition procedure to automatically determine matrix-matched calibration. The overall measurement efficiency that is determined simultaneously provides a self-diagnostic parameter for the radiochemical separation and overall instrument function. Continuous, automated operation was demonstrated over the course of 54 h, which resulted in the analysis of 215 samples plus 54 hly spike-addition samples, with consistent overall measurement efficiency for the operation of the monitor. A sample can be processed and measured automatically in just 12.5 min with a detection limit of 23.5 Bq/mL of 99Tc in low activity waste (0.495 mL sample volume), with better than 10% RSD precision at concentrations above the quantification limit. This rapid automated analysis method was developed to support nuclear waste processing operations planned for the Hanford nuclear site.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Tuning the hydrogenation of CO 2 to CH 4 over mechano-chemically prepared palladium supported on ceria

CO 2 methanation reactivity, reaction mechanism, and surface structure were investigated on a mechanochemically prepared Pd/CeO 2 catalyst (PdAcCeO 2 -M), where an oxidative pretreatment (-o) increased methane yield by a factor of two compared to a reductive pretreatment (-h). Methanation rates were maintained for over 48 h and further increased upon oxidative regeneration treatments. The surface species of both PdAcCeO 2 -M-o and PdAcCeO 2 -M-h were explored via in situ CO 2 and CO hydrogenation DRIFTS, where CO hydrogenation effectively models the dissociative CO 2 mechanism (CO 2 → CO → CH 4 ). PdAcCeO 2 -M-o yielded distinct Pd-CO adsorption and the absence of monodentate carbonate at ~ 1400 cm -1 , while AP-XPS showed that PdAcCeO 2 -M-o yielded a unique Pd δ+ contribution at 335.9 eV. By gaining insights from various in situ spectroscopic techniques, and by breaking the CO 2 hydrogenation mechanism into piecewise steps, a deeper understanding of the direct CO 2 reduction towards methane and CO over mechanochemically prepared Pd/CeO 2 catalysts was obtained.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Chemical Preparation, Crystal Structure Reinvestigation and Vibrational Study of CoNa 3 P 3 O 10 ·12H 2 O and X-ray Characterization of the New Anhydrous Triphosphate CoNa 3 P 3 O 10

The triphosphate dodecahydrate of cobalt and sodium CoNa 3 P 3 O 10 ·12H 2 O was prepared by the ion exchange resin process. Its structure was studied by X-ray diffraction and determined in the monoclinic space group P12 1 /c1 with the unit-cell parameters a = 14.6650(5) Å, b=9.1916(3) Å, c = 15.0239(5) Å,β =90.2210(10)°, Z = 4 and V = 2025.13(12) Å 3 . The thermal dehydration of this compound was performed, leading to an anhydrous new form, CoNa 3 P 3 O 10 , which was characterized by X-ray diffraction. The obtained CoNa 3 P 3 O 10 crystallized in monoclinic space group P21/n with the unit-cell parameters a=15,3774 Å, b=7,6988 A°, c=14,2832A°, β=92,9115°. The characteristic IR wavenumbers of the P 3 O 10 5- ions observed in the vibrational spectra were calculated using isotopic substitutions, which confirms the existence of these groups in the studied compound. A comparison between the IR and Raman wavenumbers of CoNa 3 P 3 O 10 ·12H 2 O, CoNa 3 P 3 O 10 and Na 5 P 3 O 10 ·12H 2 was performed. A kinetic study was also made for CoNa 3 P 3 O 10 ·12H 2 O.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Portable Sample Preparation For Chemical and Biological Analysis

Preparing samples for chemical or biological analysis is often time consuming and a critical step function to assure an accurate analysis. This invention provides an automated, hands-free, highly accurate device to prepare industrial, chemical, or biological samples for instrumental analysis methods.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Structure and Properties of SiO{sub x} Films Prepared by Chemical Etching of Amorphous Alloy Ribbons

The structure and the physical properties of amorphous SiO{sub x} films prepared by chemical etching of an iron-based amorphous ribbon alloy have been studied. The neutron diffraction and also the atomicforce and electron microscopy show that the prepared visually transparent films have amorphous structure, exhibit dielectric properties, and their morphology is similar to that of opals. The samples have been studied by differential scanning calorimetry, Raman and IR spectroscopy before and after their heat treatment. It is found that annealing of the films in air at a temperature of 1273 K leads to a change in their chemical compositions: an amorphous SiO{sub 2} compound with inclusions of SiO{sub 2} nanocrystals (crystobalite) forms.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Kondo effect in Co{sub x}Cu{sub 1-x} granular alloys prepared by chemical reduction method

Nanostructured CoCu granular alloys Co{sub x}Cu{sub 1-x} (x ≤ 0.3) have been prepared by chemical reduction method using NaBH{sub 4} as a reducing agent. Electronic transport properties are studied in the temperature range 4-300 K. Resistance exhibits a metallic behavior below room temperature and draws a minimum near 20 K in all the samples except in Co{sub 0.3}Cu{sub 0.7}. This low temperature resistivity minimum diminishes with applied magnetic field. There is also a logarithmic temperature dependence of resistivity at temperatures below 20 K. This phenomenon indicates a Kondo-like scattering mechanism involving magnetic Co impurity spin clusters in Cu host.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Structural and optical properties of Ni-doped CdS thin films prepared by chemical bath deposition method

The structural and optical behavior of undoped Cadmiun Sulphide (CdS) and Ni-doped CdS thinfilms prepared by Chemical Bath Deposition (CBD) technique is reported. The crystallite sizes of the thinfilms have been characterized by X-ray diffraction pattern (XRD). The particle sizes increase with the increase of Ni content in the CdS thinfilms. Scanning Electron Microscope (SEM) results indicated that CdS thinfilms is made up of aggregate of spherical-like particles. The composition was estimated by Energy Dispersive Analysis of X-ray (EDX) and reported. Spectroscopic studies revealed considerable improvement in transmission and the band gap of the films changes with addition of Ni dopant that is associated with variation in crystallite sizes in the nano regime.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Abrupt GaP/Si hetero-interface using bistepped Si buffer

We evidence the influence of the quality of the starting Si surface on the III-V/Si interface abruptness and on the formation of defects during the growth of III-V/Si heterogeneous crystal, using high resolution transmission electron microscopy and scanning transmission electron microscopy. GaP layers were grown by molecular beam epitaxy on vicinal Si (001). The strong effect of the Si substrate chemical preparation is first demonstrated by studying structural properties of both Si homoepitaxial layer and GaP/Si heterostructure. It is then shown that choosing adequate chemical preparation conditions and subsequent III-V regrowth conditions enables the quasi-suppression of micro-twins in the epilayer. Finally, the abruptness of GaP/Si interface is found to be very sensitive to the Si chemical preparation and is improved by the use of a bistepped Si buffer prior to III-V overgrowth.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Oriented SrFe{sub 12}O{sub 19} thin films prepared by chemical solution deposition

Thin films of SrFe{sub 12}O{sub 19} (SrM) were prepared from a solution of iron and strontium alkoxides through the chemical solution deposition method on both amorphous (glassy SiO{sub 2}), and single crystal substrates (Si(100), Si(111), Ag(111), Al{sub 2}O{sub 3}(001), MgO(111), MgAl{sub 2}O{sub 4}(111), SrTiO{sub 3}(111)) substrates. The process of crystallization was investigated by means of powder diffraction, atomic force microscopy and scanning electron microscopy. Magnetization measurements, ferromagnetic and nuclear magnetic resonance were used for evaluation of anisotropy in the films. Whilst amorphous substrates enabled growth of randomly oriented SrM phase, use of single crystal substrates resulted in samples with different degree of oriented growth. The most pronounced oriented growth was observed on SrTiO{sub 3}(111). A detailed inspection revealed that growth of SrM phase starts through the breakup of initially continuous film into isolated grains with expressive shape anisotropy and hexagonal habit. A continuous film with epitaxial relations to the substrate was produced by repeating recoating and annealing. - Graphical Abstract: XRD and AFM patterns of SrFe{sub 12}O{sub 19} thin film epitaxially grown on SrTiO{sub 3}(111) single crystal using seeding layer templating. Highlights: > Single phase SrFe{sub 12}O{sub 19} thin films prepared by chemical solution deposition. > Epitaxial growth on SrTiO{sub 3}(111) with (00l)SrM//(111)SrTiO{sub 3}, <110>SrM//<110>SrTiO{sub 3}). > Seed layer breaks into isolated single crystal islands and serves as a template. > Larger seed grains grow by consuming the grains within the bulk of recoated film.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Charge transfer in crystalline germanium/monolayer MoS 2 heterostructures prepared by chemical vapor deposition

Heterostructuring provides novel opportunities for exploring emergent phenomena and applications by developing designed properties beyond those of homogeneous materials. Advances in nanoscience enable the preparation of heterostructures formed incommensurate materials. Two-dimensional (2D) materials, such as graphene and transition metal dichalcogenides, are of particular interest due to their distinct physical characteristics. There have been recent changes in new research areas related to 2D/2D heterostructures. But, other heterostructures such as 2D/three-dimensional (3D) materials have not been thoroughly studied yet although the growth of 3D materials on 2D materials creating 2D/3D heterostructures with exceptional carrier transport properties has been reported. Here also we report a novel heterostructure composed of Ge and monolayer MoS 2 , prepared by chemical vapor deposition. A single crystalline Ge (110) thin film was grown on monolayer MoS 2 . The electrical characteristics of Ge and MoS 2 in the Ge/MoS 2 heterostructure were remarkably different from those of isolated Ge and MoS 2 . The field-effect conductivity type of the monolayer MoS 2 is converted from n-type to p-type by growth of the Ge thin film on top of it. Undoped Ge on MoS 2 is highly conducting. The observations can be explained by charge transfer in the heterostructure as opposed to chemical doping via the incorporation of impurities, based on our first-principles calculations.

36 MATERIALS SCIENCE↗

Online chemical adsorption studies of Hg, Tl, and Pb on SiO 2 and Au surfaces in preparation for chemical investigations on Cn, Nh, and Fl at TASCA

Online gas-solid adsorption studies with single-atom quantities of Hg, Tl, and Pb, the lighter homologs of the superheavy elements (SHE) copernicium (Cn, Z=112), nihonium (Nh, Z=113), and flerovium (Fl, Z=114), were carried out using short-lived radioisotopes. The interaction with Au and SiO 2 surfaces was studied and the overall chemical yield was determined. Here, suitable radioisotopes were produced in fusion-evaporation reactions, isolated in the gas-filled recoil separator TASCA, and flushed rapidly to an adjacent setup of two gas chromatography detector arrays covered with SiO 2 (first array) and Au (second array). While Tl and Pb adsorbed on the SiO 2 surface, Hg interacts only weakly and reached the Au-covered array. Our results contribute to elucidating the influence of relativistic effects on chemical properties of the heaviest elements by providing experimental data on these lighter homologs.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Oriented Y-type hexagonal ferrite thin films prepared by chemical solution deposition

Thin films of Ba{sub 2}Zn{sub 2}Fe{sub 12}O{sub 22} (Y) hexaferrite were prepared through the chemical solution deposition method on SrTiO{sub 3}(1 1 1) (ST) single crystal substrates using epitaxial SrFe{sub 12}O{sub 19} (M) hexaferrite thin layer as a seed template layer. The process of crystallization was mainly investigated by means of X-ray diffraction and atomic force microscopy. A detailed inspection revealed that growth of seed layer starts through the break-up of initially continuous film into isolated grains with expressive shape anisotropy and hexagonal habit. The vital parameters of the seed layer, i.e. thickness, substrate coverage, crystallization conditions and temperature ramp were optimized with the aim to obtain epitaxially crystallized Y phase. X-ray diffraction Pole figure measurements and Φ scans reveal perfect parallel in-plane alignment of SrTiO{sub 3} substrate and both hexaferrite phases. - Graphical abstract: XRD pole figure and AFM patterns of Ba{sub 2}Zn{sub 2}Fe{sub 12}O{sub 22} thin film epitaxially grown on SrTiO{sub 3}(1 1 1) single crystal using seeding layer templating. - Highlights: • Single phase Y-type hexagonal ferrite thin films were prepared by CSD method. • Seed M layer breaks into isolated single crystal islands and serves as a template. • Large seed grains grow by consuming the grains within the bulk of recoated film. • We explained the observed orientation relation of epitaxial domains. • Epitaxial growth on SrTiO{sub 3}(1 1 1) with relation (0 0 1){sub M,Y}//(1 1 1){sub ST}+[1 0 0]{sub M,Y}//[2 −1 −1]{sub ST}.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Study of the crystallographic phase change on copper (I) selenide thin films prepared through chemical bath deposition by varying the pH of the solution

Copper (I) selenide thin films with orthorhombic and cubic structure were deposited on glass substrates by using the chemical bath deposition technique. The effects of the solution pH on the films growth and subsequently the structural, optical and electrical properties of the films were studied. Films with orthorhombic structure were obtained from baths wherein both metal complex and hydroxide coexist; while films with cubic structure were obtained from baths where the metal hydroxide there is no present. The structural modifications are accompanied by changes in bandgap energy, morphology and electrical resistivity of the films. - Graphical abstract: “Study of the crystallographic phase change on copper (I) selenide thin films prepared through chemical bath deposition by varying the pH of the solution” by M. G. Sandoval-Paz, C. A. Rodríguez, P. F. Porcile-Saavedra, C. Trejo-Cruz. Display Omitted - Highlights: • Copper (I) selenide thin films were obtained by chemical bath deposition. • Orthorhombic to cubic phase change was induced by varying the reaction solution pH. • Orthorhombic phase is obtained mainly from a hydroxides cluster mechanism. • Cubic phase is obtained mainly from an ion by ion mechanism. • Structural, optical and electrical properties are presented as a function of pH.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Local structure analysis of diluted magnetic semiconductor Co and Al co-doped ZnO nanoparticles

In this study, Co and Al ions co-doped ZnO nanoparticles (Zn(Al, Co)O NPs) were prepared by our original chemical preparation method. The obtained samples prepared by this method, were encapsulated in amorphous SiO{sub 2}. X-ray diffraction (XRD) results showed Zn(Al, Co)O NPs had a single-phase nature with hexagonal wurtzite structure. These particle sizes could be controlled to be approximately 30 nm. We investigate the effect that the increase in the carrier has on the magnetization by doping Al to Co-doped ZnO NPs. The local structures were qualitatively analyzed using X-ray absorption fine structure (XAFS) measurements.

36 MATERIALS SCIENCE↗