Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CASTING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2017

Casting Characteristics of High Cerium Content Aluminum Alloys

This paper compares the castability of the near eutectic aluminum-cerium alloy system to the aluminum-silicon and aluminum-copper systems. The alloys are compared based on die filling capability, feeding characteristics and tendency to hot tear in both sand cast and permanent mold applications. The castability ranking of the binary Al–Ce systems is as good as the aluminum-silicon system with some deterioration as additional alloying elements are added. In alloy systems that use cerium in combination with common aluminum alloying elements such as silicon, magnesium and/or copper, the casting characteristics are generally better than the aluminum-copper system. In general, production systems for melting, de-gassing and other processing of aluminum-silicon or aluminum-copper alloys can be used without modification for conventional casting of aluminum-cerium alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Co-dependent microstructural evolution pathways in metastable d-ferrite in cast austenitic stainless steels during thermal aging

Cast austenitic stainless steels (CASS) are excellent alloys because they combine high corrosion resistance with high strength and toughness. However, they are susceptible to embrittlement upon long-term thermal aging at elevated temperatures. Thus, the microstructural evolution pathways during thermal aging need to be understood to predict and potentially prevent embrittlement. Atom probe tomography was used to identify and quantify the microstructural evolution pathways of the d-ferrite in different CASS alloys aged for up to 10,000 hours at temperatures between 290 °C and 400 °C. The four steels – CF8, CF8M, CF3, and CF3M – which vary by Mo and C concentration, each experienced spinodal decomposition of the d-ferrite, and precipitation of G-phase clusters and Cu clusters attached to the G-phase. There were large differences in the extent of these features due to their Mo and C concentration. Using radial distribution function analysis, the interactions of constituent elements was found to determine the evolution of these features, with Mo and C specifically influencing the movement of Cr, Ni, Si, Mn, and Cu atoms due to their relative miscibility with these elements. The results will help inform predictive models for the use of duplex stainless steels for extended operation at high temperatures.

Duplex stainless steel, Aging, Spinodal decomposit↗
DOE OSTI2017

Triple Plate Mold Final Report: Optimization of the Mold Design and Casting Parameters for a Thin U-10mo Fuel Casting

This work describes the experiments and modeling that have been performed to improve and try to optimize the simultaneous casting of three plates of U-10wt%Mo in a single coil vacuum induction melting (VIM) furnace. The plates of interest are 280 mm wide by 203 mm tall by 5 mm thick (11" x 8" x 0.2"). The initial mold design and processing parameters were supplied by Y-12. The mold and casting cavity were instrumented with a number of thermocouples, and the casting performed to determine the thermal history of the mold and casting. The resulting cast plates were radiographed and numerous defects identified. Metallography was performed to help identify the nature of the radiographically observed defects. This information was then used to validate a mold filling and solidification model of that casting. Based on the initial casting, good casting design practice, and process simulation of several design alternatives, a revised design was developed with the goal of minimizing casting defects such as porosity. The redesigned mold had a larger hot-top and had its long axis along the horizontal direction. These changes were to try to develop a strong thermal gradient conducive to good feeding and minimization of micro- and macroporosity in the cast plates. An instrumented casting was then performed with the revised mold design and a linear distributor. This design yielded cast plates with significantly less radiographically identified defects. Unfortunately, there was significant variation in plate weight and metal content in their hot-tops. Fluid flow simulations were then performed on this mold/distributor design. This helped identify the issue with this linear distributor design. Additional simulations were then performed on candidate distributor redesigns and a preferred distributor annular design was identified. This improved annular design was used to produce a third instrumented casting with favorable results. These refined designs and their radiographic characterization are compared to the initial design.

36 MATERIALS SCIENCE↗
DOE OSTI2018

On the Steel–Aluminum Hybrid Casting by Sand Casting

Hybrid casting is a well-known technology to join steel inserts and aluminum. In order to achieve a high-performance material-based joining between steel and aluminum, a new PVD Al-Si-(Fe) coating, which consists of two sub-layers, has been successfully developed for high-pressure die casting. This coating system has been investigated further in this work for the sand casting process. By extending the sand casting process to the plaster casting process with preheating possibilities for the coated steel inserts, a material-based connection between steel and aluminum with a tensile shear strength of 7.7 MPa could be created. The ductility of this connection is decreased comparing with the connection manufactured by die casting. SEM and EDS analysis and diffusion experiments show that the difference of mechanical properties between plaster and die casting is caused by the extensive diffusion and the corresponding layer growth at plaster casting. The edge separation in plaster casting is a result of the edge stresses due to the different thermal expansion of steel and aluminum which can be suppressed at high-pressure die casting. To improve the joining properties at sand casting, it is necessary to control the layer diffusion by adding other alloy elements such as Mn into the Al-Si-(Fe) coating layer.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Local Modification of Cast Aluminum Alloys via the Cast-and-Print Process

Casting of aluminum alloys is a cost-effective way to mass manufacture bulk aluminum parts for automotive applications. However, the casting process requires filling of a mold, which imposes some limitations on the geometries that can be successfully cast and limits parts to be a uniform material. Therefore, we proposed that a hybrid casting plus additive manufacturing approach, Cast-and-Print, which could be used to locally modify the properties and geometry of cast parts to create difficult-to-cast, functional features. Here, we report the results of the properties of deposited materials on cast substrate, the properties of the interface of the deposited and cast material, and the application of the Cast-and-Print method to deposit rivet tabs on high-pressure die cast plates. Ultimately, the approach appears viable, but there are engineering challenges present to reliable additive processing of aluminum wires that need to be overcome for successful implementation of the technology.

42 ENGINEERING↗
DOE OSTI2019

Mathematical Modeling on the Influence of Casting Parameters on Initial Solidification at the Meniscus of Slab Continuous Casting

In the current study, the two-dimensional mold model was applied to investigate the influence of different casting parameters on the initial solidification at the meniscus of the continuous casting mold. The profile of the meniscus and the slag rim, and the heat flux on the hot face of the copper plate, were compared with different locations of the mold and different casting parameters. The depth of the oscillation marks and solidified meniscus through simulation was measured with different casting parameters. With the mold oscillating downward from the peak to the valley, the maximum heat flux on the hot face of the copper plate near the meniscus increased from 4.3 to 5.5 MW/m{sup 2}, the thickness of the slag rim decreased from 4.7 to 4.2 mm, and the height of the curved meniscus also decreased. With the increase of casting speed from 1.2 to 1.45 m/min, the maximum speed of the upper backflow increased from 0.6 to 0.8 m/s, and the lowest location of the meniscus at approximately 310 mm from the copper plate decreased from 22 to 12 mm below the meniscus near the nozzle, where the slag entrapment easily occurred. With the increase of the casting speed, casting superheat, and oscillation frequency, and the decrease of the water flow rate in the mold and oscillation amplitude, the thickness of the slag rim decreased. With the increase of casting speed and superheat, and the decrease of the water flow rate in the mold, oscillation frequency, and oscillation amplitude, the depth of the solidified meniscus decreased. The regression equation was fitted to estimate the depth of hooks at the subsurface of slabs.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Hot-Tearing Assessment of Multicomponent Nongrain-Refined Al-Cu Alloys for Permanent Mold Castings Based on Load Measurements in a Constrained Mold

The hot-tearing resistance of multicomponent Al-Cu alloys during permanent mold casting was investigated using a constrained permanent mold in which the load and temperature were measured. The nominal Cu composition was varied from 5 to 8 wt pct. Casting experiments were conducted without adding any grain-refining inoculants. The following variables, which were obtained from the measured load data during casting, were considered to assess the hot-tearing resistance of the Al-Cu multicomponent alloys: “V”-like signature in the load rate variation, load at solidus point, and load rate average over the freezing range. In addition, a hot-tearing criterion based on the variation of the fraction of solid in the late stages of solidification was used. It was found that all criteria considered can accurately predict the alloys with the lowest and highest hot-tear resistance, respectively. It was found that the rate of measured load during casting could be used to indicate substantial hot tearing. However, the load rate variation could not be used to detect when small hot tears were present. Among all the criteria considered, the load at the solidus point shows an excellent agreement with experimentally observed hot-tearing resistance for all but one alloy. The poorly resistant hot-tearing alloys exhibited mainly coarse columnar grains while the most hot-tearing resistant alloys exhibited a much more refined grain microstructure. This is the first study in which good hot-tear resistance is demonstrated for multicomponent Al-Cu alloys with nominal Cu content greater than 7 wt pct.

36 MATERIALS SCIENCE↗
DOE OSTI2020

An Alternative Casting Technique to Improve the Creep Resistance of Cast INCONEL Alloy 740H

The increasing performance requirements of power plant designs, such as advanced-ultra supercritical (A-USC), require the use of Ni-based superalloys to replace high-strength, ferritic-martensitic steels for components subjected to temperatures above 898 K (625 °C) and for austenitic stainless steels components at temperatures above 973 K (700 °C). To date, commercial Ni-based superalloy INCONEL 740H has been shown to be appropriate for use in A-USC power plants as boiler components in a wrought product. However, large complex components in boilers as well as other casings in the turbine and valve chest require castings of a thick-wall nature. Using the alloy in its cast form would be significantly valuable in terms of range of component size, geometry and complexity. Previous investigations revealed short creep lives from cast INCONEL alloy 740H. Here in this investigation, an alternative casting route that utilized a melt procedure resulting in a fine-grain casting, and in conjunction with a computationally optimized homogenization heat treatment, not only controlled the grain size and grain boundary structure but minimized chemistry variability and segregation. A primarily equiaxed and homogenous grain size distribution was obtained from this approach with better repartition of M 23 C 6 carbides along the grain boundaries. Furthermore, better than 38 pct increase was obtained for this material in comparison to the creep life obtained from the best performing conventionally cast material. More importantly, the fine-grain homogenized (FGH) casting route resulted in the Larson–Miller plot for this material that coincided with that of wrought alloy 740. At low creep stresses (with a test still in progress), the FGH casting is resulting in higher values of the LMP than the wrought alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Deformation Behavior of Pure Copper Castings with As-Cast Surfaces for Electrical Parts

Herein, the tensile deformation behavior of pure copper castings with as-cast surfaces was investigated. It was found that small and sufficiently large uniform elongation types corresponded, respectively, to the presence or absence of a Cu-Cu{sub 2}O eutectic phase in the microstructure. Fissure defects were observed near the as-cast surfaces when the eutectic phase was present, probably leading to stress concentration. On the other hand, surface pinholes were observed when the eutectic phase was absent, and these were not prevented by directional solidification. Although the as-cast specimens (non-directionally solidified) exhibited a slightly reduced uniform elongation compared to the machined specimens in the absence of the eutectic phase, the directionally solidified as-cast samples exhibited a uniform elongation that was similar to that of the machined specimens. In addition, micropore arrays were formed along the grain boundaries inside the castings when the eutectic phase was absent, whereas almost no micropores were observed inside the directionally solidified as-cast specimens because the solidification process involved a faster cooling rate and/or higher temperature gradient. These results do not only suggest the existence of surface pinholes but also indicate that microporosity can reduce the cross-sectional area of the specimens, thus, affecting their uniform elongation.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Glovebox Advanced Casting System Casting Optimization

Casting optimization in the GACS included three broad areas; casting of U-10Zr pins, incorporation of an integral FCCI barrier, and development of a permanent crucible coating. U-10Zr casting was improved over last year’s results by modifying the crucible design to minimize contact with the colder mold. Through these modifications casting of a three pin batch was successful. Incorporation of an integral FCCI barrier also was optimized through furnace chamber pressure changes during the casting cycle to reduce gas pressures in the mold cavities which led to three full length pins being cast which incorporated FCCI barriers of three different thicknesses. Permanent crucible coatings were tested against a base case; 1500°C for 10 minutes in a U-20Pu-10Zr molten alloy. None of the candidate coating materials showed evidence of failure upon initial visual examination. In all areas of work a large amount of characterization will be needed to fully determine the effects of the optimization activities. The characterization activities and future work will occur next year.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A New Recycled Al–Si–Mg Alloy for Sustainable Structural Die Casting Applications

The use of secondary aluminum for structural components in the automotive industry is limited by the high Fe contents in recycled alloys which often result in the formation of brittle β-Al 5 FeSi phase which reduces the ductility of aluminum castings. In this study, a new secondary Al-Si-Mg alloy with high Fe content (about 0.44 wt.%) was developed for die casting applications. Based on thermodynamic modeling, manganese was added to obtain a designed Fe-to-Mn ratio of 2 which successfully suppressed the formation of β-Al 5 FeSi phase, by forming α-Al 15 (Fe,Mn) 3 Si 2 phase with rounded or hexagonal morphology. Additionally, a fine needle-like π-Al 8 FeMg 3 Si 2 phase was also formed within the eutectic regions. The new recycled alloy showed comparable mechanical properties in as-cast and heat treated (T5 and T6) conditions to three major primary die cast alloys (≤ 0.2 wt.% Fe) with similar composition. Ductility up to 7.4% from tensile elongation was achieved in as-cast recycled alloy due to the modification and refinement of α-Al 15 (Fe,Mn) 3 Si 2 by Mn and Sr additions. Tensile elongation was further improved to 9.1% after T6 treatment as a result of dissolution of π-Al 8 FeMg 3 Si 2 phase, defragmentation of α-Al 15 (Fe,Mn) 3 Si 2 and the spheroidization of Si phase. This new alloy provides a promising path for increasing usage of recycled aluminum with high Fe content in structural die castings for automotive and other applications.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Comparative Analysis of the Microstructural Features of 28 wt.% Cr Cast Iron Fabricated by Pulsed Plasma Deposition and Conventional Casting

The effect of pulsed plasma deposition (by an electrothermal axial plasma accelerator) followed by post-heat treatment on the structure and microhardness of a 28 wt.% Cr white cast iron is analyzed and discussed with respect to the microstructure of the conventionally cast monolithic counterpart. The cast iron (as deposited on a 14 wt.% Cr cast iron substrate) had a microhardness of 630-750 HV{sub 0.05}; it had layered light contrast/dark contrast structure where dark contrast layers contain fine carbide network. Pulsed plasma deposition followed by heat treatment resulted in a substantial refinement of the microstructure: eutectic M{sub 7}C{sub 3} coarse acicular plates in the conventional cast iron were replaced by fine M{sub 7}C{sub 3}, M{sub 3}C{sub 2}, M{sub 3}C particles (Cr depleted in favor of Fe), while the initial carbide particle of 2-3 μm was reduced to 0.6 μm. Secondary dendrite arm spacing decreased from 15 to 1.3 μm, accordingly. The carbide volume fraction in the post-heat-treated coating remarkably increased with respect to the conventional counterpart resulting in a substantial increase in the coating hardness (1300-1750 HV{sub 0.05}). The heat-treated coating displayed higher resistance to three-body abrasion than the as-deposited coating and similar resistance with that of the conventionally cast iron.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effect of annealing after strip casting on microstructure, precipitates and texture in non-oriented silicon steel produced by twin-roll strip casting

Highlights: • Non-oriented silicon steel with superior magnetic properties was produced by twin-roll strip casting. • The effect of annealing after strip casting on microstructure, precipitates and texture was investigated. • Role of precipitates in microstructure and texture evolution along the entire route was explored. • High magnetic induction and strong λ-fiber texture was obtained by optimizing strip annealing process. - Abstract: A 3.1 mm thick non-oriented Fe-1.0% Si steel as-cast strip was produced by twin-roll strip casting. Samples with/without strip annealing were cold rolled to 0.5 mm and then annealed. The development of microstructure, precipitate and texture was characterized along the entire processing route. It was found that annealing after strip casting had a minor influence on the average grain size and texture of the as-cast strip. A large number of particles precipitated and coarsened during the strip annealing process. Meanwhile, precipitates hindered dislocation slip and crystal rotation such that more significant in-grain shear bands were formed in cold rolled sheets. During recrystallization annealing process, the newly formed fine precipitates in directly cold-rolled sheets consumed stored strain energy and also hindered grain growth. But the initial precipitates in the annealed strip grew further and the effect of pinning of dislocations and grain boundary was lost. Therefore, annealed sheets with strip annealing process showed homogeneous equiaxed grains and the recrystallization texture was characterized by strong λ-fiber texture, which led to high permeability.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Direct Cast U-6Nb – 2017 Progress on Cylindrical Castings

This report describes work to further develop a sound technical basis and best practices for mold design and process parameters for the Direct Casting of U-6wt%Nb components. One major challenge to the production of U-6Nb components is the propensity for niobium segregation during casting and solidification. This is especially true for cylindrical castings where the vertical side walls allow flotation of Nb resulting in severe inverse macrosegregation. In this work, a small (120 mm diameter by 180 mm tall) and large cylinder (250 mm diameter by 310 mm tall) are examined with a focus on reducing, or eliminating, niobium segregation. It is demonstrated that counter gravity casting (top-to-bottom solidification) can be used to minimize segregation in the small cylinder. Attempts to counter gravity cast the large cylinder were unsuccessful, in large part due to size limitations of the current furnace. A path forward for casting of the large cylinders is discussed.

42 ENGINEERING↗
DOE OSTI2019

An integrated two-dimensional modeling method for predicting ductility of thin-walled die cast magnesium

In this paper, a two-dimensional (2D) microstructure-based modeling method is developed in order to predict the ductility of a thin-walled high pressure die cast magnesium (Mg) by considering the three-dimensional (3D) thru-thickness pore distributions. For this purpose, a series of 3D synthetic microstructure-based finite element models and the corresponding 2D models are first generated with various pore volume fractions, pore size distributions and pore shapes. The input material properties for the 2D models are determined based on the 3D cubic model with a spherical pore and the generalized Neuber’s rule. Based on the resulting ductility of the 3D and 2D models, a 3D/2D ductility correlation curve is developed as a function of the characteristics/shape of the input fracture strain curve used in the 3D model. The validity of the ductility correlation curve is examined with casting samples with actual microstructures. Here, the results show that the suggested 2D modeling methodology can be used together with the ductility correlation curve in predicting the ductility of thin-walled Mg castings.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effects of Casting Parameters and Impurity Concentrations on As-Cast U–10Mo

This work investigates the effects of casting parameter changes on as-cast uranium-10 wt% molybdenum alloys on a 1-2kg scale. A commercial tilt-pour vacuum induction melting system was utilized to study the effects of casting atmosphere, total heating time, hold time at maximum temperature, mold temperature, and crucible type on the as-cast microstructure of U-10Mo. Ten thin plates (5.08 mm thick) and four thick plates (25.4 mm and 63.5 mm thick) were cast and analyzed for carbon, oxygen, hydrogen, and nitrogen impurities. Additionally, molybdenum content and primary dendrite length (PDL) of the microstructure was quantified. A statistical evaluation was performed to identify key carbon and oxygen relationships with operating parameters, impurities, and primary dendrite length. Additional factors investigated include: crucible material, time at maximum temperature, total heating time, and pour temperature. Zirconia crucibles reduced carbon content on average by 35%. Additionally, there was a significant statistical association between carbon and oxygen content, between oxygen content and maximum temperature hold time, between mold temperature and PDL, and between PDL, maximum temperature hold time and mold temperature.

Huber, Zachary F.↗
DOE OSTI2023

Cylinder block casting slab core cast geometry for sawcut entrance enhancement

An automobile vehicle engine includes multiple water jackets individually formed in a cast engine block proximate to successive ones of multiple cylinder bores. Multiple cast-in place transition regions are individually formed during a casting operation of the cast engine block at entrances to individual ones of the multiple water jackets. Individual ones of multiple sawcuts open into individual ones of the multiple cast-in place transition regions.

Petrus, Ronald John↗
DOE OSTI2018

Heat Transfer Coefficient at Cast-Mold Interface During Centrifugal Casting: Calculation of Air Gap

During centrifugal casting, the thermal resistance at the cast-mold interface represents a main blockage mechanism for heat transfer. In addition to the refractory coating, an air gap begins to form due to the shrinkage of the casting and the mold expansion, under the continuous influence of strong centrifugal forces. Here, the heat transfer coefficient at the cast-mold interface h has been determined from calculations of the air gap thickness d{sub a} based on a plane stress model taking into account thermoelastic stresses, centrifugal forces, plastic deformations, and a temperature-dependent Young’s modulus. The numerical approach proposed here is rather novel and tries to offer an alternative to the empirical formulas usually used in numerical simulations for a description of a time-dependent heat transfer coefficient h. Several numerical tests were performed for different coating thicknesses d{sub C}, rotation rates Ω, and temperatures of solidus T{sub sol}. Results demonstrated that the scenario at the interface is unique for each set of parameters, hindering the possibility of employing empirical formulas without a preceding experiment being performed. Initial values of h are simply equivalent to the ratio of the coating thermal conductivity and its thickness (~ 1000 Wm{sup −2} K{sup −1}). Later, when the air gap is formed, h drops exponentially to values at least one order of magnitude smaller (~ 100 Wm{sup −2} K{sup −1}).

36 MATERIALS SCIENCE↗