Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “BUCKLING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1962

BUCKLING AND POST-BUCKLING OF ELASTIC SHELLS

Some theoretical investigations of buckling of elastic shells are surveyed in this report. Only geometrically perfect shells are considered; initial dents and out-of-roundness are not taken into account. Several questions raised by the studies are: (a) Under what conditions is the infinitesimal theory of buckling of shells adequate? (b) How does the energy theory of buckling of shells correlate with the method based on equilibrium equations for bending moments, tensions, and shears in a buckled configuration? (c) How important are nonlinear terms in the tangential displacements u, v in the strain-displacement relations for buckling and post-buckling studies? (d) How important are the boundary conditions for u, v in affecting stability? (e) If a condition of snap-through is approached, how much external work is required to push the shell "over the hump" into the buckled configuration? (f) How reliable are mathematical approximations used previously in the infinitesimal theory of buckling of shells? Tentative and incomplete answers to some of these questions are suggested.

ELASTIC BUCKLING↗
NASA NTRS1944

The inward bulge type buckling of monocoque cylinders I : calculation of the effect upon the buckling stress of a compressive force, a nonlinear direct stress distribution, and a shear force

In the present part I of a series of reports on the inward bulge type buckling of monocoque cylinders the buckling load in combined bending and compression is first derived. Next the reduction in the buckling load because of a nonlinear direct stress distribution is determined. In experiments nonlinearity may result from an inadequate stiffness of the end attachments in actual airplanes from the existence of concentrated loads or cut-outs. The effect of a shearing force upon the critical load is investigated through an analysis of the results of tests carried out at GALCIT with 55 reinforced monocoque cylinders. Finally, a simple criterion of general instability is presented in the form of a buckling inequality which should be helpful to the designer of a monocoque in determining the sizes of the rings required for excluding the possibility of inward bulge type buckling.

Hoff, N J↗
NASA NTRS1944

The inward bulge type buckling of monocoque cylinders II : experimental investigation of the buckling in combined bending and compression

This paper is the second part of a series of reports on the inward bulge type buckling of monocoque cylinders. It presents the results of an experimental investigation of buckling in combined bending and compression. In the investigation it was found that the theory developed in part I of the present series predicts the buckling load in combined bending and compression with the same degree of accuracy as the older theory does in pure bending. In the realm covered by the experiments no systematic variation of the parameter N was observed. The analysis of the test results afforded a check on the theories of buckling of a curved panel. The agreement between experiment and theory was reasonably good. In addition, the effect of the end conditions upon the stress distribution under loads and upon initial stresses was investigated.

LOADS-CYLINDERS, MONOCOQUE-STRESS DISTRIBUTION↗
NASA NTRS1974

Theory of buckling and post-buckling behavior of elastic structures

The present paper provides a unified, general presentation of the basic theory of the buckling and post-buckling behavior of elastic structures in a form suitable for application to a wide variety of special problems. The notation of functional analysis is used for this purpose. Before the general analysis, simple conceptual models are used to elucidate the basic concepts of bifurcation buckling, snap buckling, imperfection sensitivity, load-shortening relations, and stability. The energy approach, the virtual-work approach, and mode interaction are discussed. The derivations and results are applicable to continua and finite-dimensional systems. The virtual-work and energy approaches are given separate treatments, but their equivalence is made explicit. The basic concepts of stability occupy a secondary position in the present approach.

Budiansky, B.↗
NASA NTRS2022

Buckling Test and Analysis of the 8-Foot-Diameter Sandwich Composite Cylinder Test Article CTA8.2 as Part of the Shell Buckling Knockdown Factor Project: Test Dates 5-7 December 2017

It is well known that the buckling response of thin shell structures can be sensitive to small imperfections in the geometry and loading. The NASA Engineering and Safety Center (NESC) Shell Buckling Knockdown Factor Project (SBKF) has the goal of developing buckling design recommendations for select classes of metallic and composite shells. Part of completed SBKF work is described in this report. In particular, the test and analysis results from the second SBKF composite test article, CTA8.2, are described. This test was the second in a series of tests on sandwich composite cylinders that can be used to experimentally validate analysis methods, which in turn can be used to develop analysis-based shell buckling design guidelines for sandwich composite launch-vehicle cylindrical structures. CTA8.2 was an 8-foot diameter honeycomb-core sandwich cylinder that was fabricated and tested at the Marshall Space Flight Center (MSFC). The primary objectives of this test were to interrogate the structural capability of the composite test article, and to verify the test-article design and analysis approach for cylinders subjected to axial compression loads. This report contains the descriptions of the test-article design, fabrication, and test. The pre-test modeling and analysis methods, and corresponding results used in support of the test-article design and test planning, are also described. Additional post-test modeling and analysis efforts and results follow. Selected test results are compared to pre-test predictions and post-test analyses.

Adam Przekop↗
NASA NTRS2022

Buckling Test and Analysis of the 8-foot-diameter Sandwich Composite Cylinder Test Article CTA8.3 as Part of the Shell Buckling Knockdown Factor Project: Test Dates 16~19 December 2019

This report describes work that is part of SBKF-the test and analysis results from the third SBKF cylindrical sandwich composite test article, which was designated SBKF-P3-CYL-CTA8.3. This test was the third in a series of tests on sandwich composite cylinders that can be used to experimentally validate analysis methods, which in turn can be used to develop analysis-based shell buckling design guidelines for sandwich composite launch-vehicle cylindrical structures. The primary objectives of this test were to interrogate the structural capability of the composite test article, and to verify the test-article design and analysis approach for cylinders subjected to axial compression and combined compression and bending loads.

Sandwich composite cylinder↗
NASA NTRS1990

Thermal buckling and post-buckling of symmetric composite plates

The thermally induced buckling and postbuckling behavior of square and rectangular simply supported composite plates is examined using the Rayleigh-Ritz method in conjunction with the second variations of the total potential energy. Spatially uniform and nonuniform temperatures and laminates with material axes that are not aligned with the plate edges (skewed material axes) are considered. Results of the analysis are presented in graphic form.

Meyers, C. A.↗
NASA NTRS1991

Finite element analysis of thermal post-buckling and vibrations of thermally buckled composite plates

A finite-element formulation is presented for the analysis of thermal postbuckling and free vibrations of thermally buckled, thin, rectangular, arbitrarily laminated, composite plates. The thermal load is considered to be a large steady-state temperature change over the plate. The equations of motion are derived from the principle of virtual work. The solution procedures are briefly discussed. Finite-element results are compared with existing isotropic and composite solutions. Examples studied include symmetric and antisymmetric angle-ply laminates and certain symmetric laminates.

Mei, Chuh↗
NASA NTRS1955

On the mechanism of buckling of a circular cylindrical shell under axial compression

The present paper deals with the buckling of a circular cylindrical shell under axial compression from the viewpoint of energy and the characteristics of deformation. It is shown first, both theoretically and experimentally, that the reason why the buckling of a cylindrical shell is quite different from that of a flat plate is attributable to the existence of a nearly developable surface far apart from the original cylindrical surface. Based upon this result, the experimental fact that the buckling is really not general but local, that is, that the buckled region is limited axially to a range of 1.5 times the wave length of the lobe, is explained by the theoretical result that the minimum buckling load is smaller in the local buckling than in the general buckling case. The occurrence of local buckling is affirmed also from the viewpoint of the energy barrier to be jumped over during buckling, and from a comparison of the theoretical post-buckling state with the experimental results. Finally, the local buckling with the load applied by a spring is analyzed, and it is proved that the minimum buckling load increased with an increase of rigidity of the spring.

SHELLS, STRUCTURAL↗
NASA NTRS1994

The buckling response of symmetrically laminated composite plates having a trapezoidal planform area

The focus of this work is the buckling response of symmetrically laminated composite plates having a planform area in the shape of an isosceles trapezoid. The loading is assumed to be inplane and applied perpendicular to the parallel ends of the plate. The tapered edges of the plate are assumed to have simply supported boundary conditions, while the parallel ends are assumed to have either simply supported or clamped boundary conditions. A semi-analytic closed-form solution based on energy principles and the Trefftz stability criterion is derived and solutions are obtained using the Rayleigh-Ritz method. Intrinsic in this solution is a simplified prebuckling analysis which approximates the inplane force resultant distributions by the forms Nx=P/W(x) and Ny=Nxy=0, where P is the applied load and W(x) is the plate width which, for the trapezoidal planform, varies linearly with the lengthwise coordinate x. The out-of-plane displacement is approximated by a double trigonometric series. This analysis is posed in terms of four nondimensional parameters representing orthotropic and anisotropic material properties, and two nondimensional parameters representing geometric properties. For comparison purposes, a number of specific plate geometry, ply orientation, and stacking sequence combinations are investigated using the general purpose finite element code ABAQUS. Comparison of buckling coefficients calculated using the semi-analytical model and the finite element model show agreement within 5 percent, in general, and within 15 percent for the worst cases. In order to verify both the finite element and semi-analytical analyses, buckling loads are measured for graphite/epoxy plates having a wide range of plate geometries and stacking sequences. Test fixtures, instrumentation system, and experimental technique are described. Experimental results for the buckling load, the buckled mode shape, and the prebuckling plate stiffness are presented and show good agreement with the analytical results regarding the buckling load and the prebuckling plate stiffness. However, the experimental results show that for some cases the analysis underpredicts the number of halfwaves in the buckled mode shape. In the context of the definitions of taper ratio and aspect ratio used in this study, it is concluded that the buckling load always increases as taper ratio increases for a given aspect ratio for plates having simply supported boundary conditions on the parallel ends. There are combinations of plate geometry and ply stackling sequences, however, that reverse this trend for plates having clamped boundary conditions on the parallel ends such that an increase in the taper ratio causes a decrease in the buckling load. The clamped boundary conditions on the parallel ends of the plate are shown to increase the buckling load compared to simply supported boundary conditions. Also, anisotropy (the D16 and D26 terms) is shown to decrease the buckling load and skew the buckled mode shape for both the simply supported and clamped boundary conditions.

Radloff, H. D., II↗
NASA NTRSDate not supplied

Nonlinear Buckling Analysis of Tow-Steered Composite Cylinders with Cutouts

The buckling and postbuckling behavior of two composite tow-steered shells with cutouts of different sizes is assessed using nonlinear finite element (FE) analysis and compared to experimental measurements. The cylindrical shells are manufactured using an automated fiber placement system, where the shells’ fiber orientation angles vary continuously around the shell circumference from ±10 degrees on the crown and keel to ±45 degrees on the sides. One shell features thickness variations due to tow overlaps that result from application of all 24 tows during each pass of the fiber placement system. The second shell uses the system’s tow drop/add capability to achieve a more uniform wall thickness without overlaps. Unreinforced cutouts of two different sizes—the first smaller cutout representing a passenger door on a commercial aircraft and the second larger cutout a cargo door—were machined into each of the two cylinders resulting in a total of four test cases. These cylinders were tested in axial compression and buckled elastically in previous work and are now analyzed using nonlinear FE models to compare bifurcation buckling loads as well as the load-displacement response in the prebuckling and postbuckling regimes. For all four shells analyzed, the prebuckling stiffness, buckling load, and deformation mode sequence throughout the loading-unloading cycle is accurately reproduced by the models. In particular, the shells first buckle locally around the cutouts in a stable (super-critical) manner with only a slight decrease in axial stiffness, which occurs due to the favorable load redistribution facilitated by tow steering. The shells then buckle globally in an unstable (sub-critical) manner with diamond-shaped buckles forming to the left and right of the cutouts. The buckling load of all shells with cutouts is at least 82% of the buckling load of the pristine shells without cutouts. Overall, the ability to sustain local buckling phenomena, and the relatively small reductions in global buckling load compared to pristine shells without cutouts, demonstrates the great potential of using tow steering to mitigate the adverse effects of cutouts in axially-compressed shell structures.

composites↗
NASA NTRSDate not supplied

Nonlinear Buckling Analysis of Tow-Steered Composite Cylinders with Cutouts

The buckling and postbuckling behavior of two composite tow-steered shells with cutouts of different sizes is assessed using nonlinear finite element (FE) analysis and compared to experimental measurements. The cylindrical shells are manufactured using an automated fiber placement system, where the shells’ fiber orientation angles vary continuously around the shell circumference from 10 degrees on the crown and keel to 45 degrees on the sides. One shell features thickness variations due to tow overlaps that result from application of all 24 tows during each pass of the fiber placement system. The second shell uses the system’s tow drop/add capability to achieve a more uniform wall thickness without overlaps. Unreinforced cutouts of two different sizes—the first smaller cutout representing a passenger door on a commercial aircraft and the second larger cutout a cargo door—were machined into each of the two cylinders resulting in a total of four test cases. These cylinders were tested in axial compression and buckled elastically in previous work and are now analyzed using nonlinear FE models to compare bifurcation buckling loads as well as the load-displacement response in the prebuckling and postbuckling regimes. For all four shells analyzed, the prebuckling stiffness, buckling load, and deformation mode sequence throughout the loading-unloading cycle is accurately reproduced by the models. In particular, the shells first buckle locally around the cutouts in a stable (super-critical) manner with only a slight decrease in axial stiffness, which occurs due to the favorable load redistribution facilitated by tow steering. The shells then buckle globally in an unstable (sub-critical) manner with diamond-shaped buckles forming to the left and right of the cutouts. The buckling load of all shells with cutouts is at least 82% of the buckling load of the pristine shells without cutouts. Overall, the ability to sustain local buckling phenomena, and the relatively small reductions in global buckling load compared to pristine shells without cutouts, demonstrates the great potential of using tow steering to mitigate the adverse effects of cutouts in axially-compressed shell structures.

Buckling↗
NASA NTRSDate not supplied

Buckling Behavior of Conical-Cylindrical Shells and Design Considerations for Launch-Vehicle Applications

Traditionally, launch vehicles are constructed with a series of buckling-prone thin-walled cylindrical and conical shells, in which the buckling behavior of these shells has been well studied and buckling design guidance exists. Conical-cylindrical shell geometry is now being utilized for launch-vehicle stage adapters and payload adapters due to advances in manufacturing and numerical techniques, but there is no available buckling design guidance for this nontraditional combined geometry. In order to provide design recommendations, the buckling behavior and imperfection sensitivity of conical-cylindrical shells and how it differs from the conical and cylindrical components needs to be better understood. From this premise, it is possible to investigate whether or not the buckling knockdown factor guidelines for conical and cylindrical shells outlined in NASA SP-8019 and NASA SP-8007, respectively, are still applicable. The results in this paper will show that the current recommendations are not appropriate in some cases. In addition, it was observed that the large rotations and displacements near the transition between the cone and cylinder can have a larger effect on the buckling load than the presence of radial imperfections for conical-cylindrical shells, which is different than conical and cylindrical shells. More interesting is the fact that design modifications to increase the buckling capability of a conical-cylindrical shell such as adding reinforcement, which may add mass, will make the shell more sensitive to imperfections. The increased imperfection sensitivity may negate the increase in buckling capability that was thought to be achievable. In the end, it may be more beneficial to design a conical-cylindrical shell in which the buckling behavior is dominated by the more predictable geometric nonlinearity, which may lead to an overall lower buckling load, but a lower knockdown factor may be possible since it will not be as sensitive to the less-known radial imperfections.

Buckling↗
NASA NTRS2013

Buckling Design and Analysis of a Payload Fairing One-Sixth Cylindrical Arc-Segment Panel

Design and analysis results are reported for a panel that is a 16th arc-segment of a full 33-ft diameter cylindrical barrel section of a payload fairing structure. Six such panels could be used to construct the fairing barrel, and, as such, compression buckling testing of a 16th arc-segment panel would serve as a validation test of the buckling analyses used to design the fairing panels. In this report, linear and nonlinear buckling analyses have been performed using finite element software for 16th arc-segment panels composed of aluminum honeycomb core with graphiteepoxy composite facesheets and an alternative fiber reinforced foam (FRF) composite sandwich design. The cross sections of both concepts were sized to represent realistic Space Launch Systems (SLS) Payload Fairing panels. Based on shell-based linear buckling analyses, smaller, more manageable buckling test panel dimensions were determined such that the panel would still be expected to buckle with a circumferential (as opposed to column-like) mode with significant separation between the first and second buckling modes. More detailed nonlinear buckling analyses were then conducted for honeycomb panels of various sizes using both Abaqus and ANSYS finite element codes, and for the smaller size panel, a solid-based finite element analysis was conducted. Finally, for the smaller size FRF panel, nonlinear buckling analysis was performed wherein geometric imperfections measured from an actual manufactured FRF were included. It was found that the measured imperfection did not significantly affect the panel's predicted buckling response

composite structures↗