Measurement of the super 10 B/n, alpha/ super 7 Li, super 7 Li' relative cross sections in the kev region.
Boron 10 absorption cross sections from counting ratios measurements of boron trifluoride proportional counter used to monitor neutron fluxes
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Boron 10 absorption cross sections from counting ratios measurements of boron trifluoride proportional counter used to monitor neutron fluxes
Shielding material containing Boron 10 and gadoliunium for neutron absorption has been developed to reduce interference from low energy neutrons in measurement of fission neutron spectrum using Li-6 fast neutron spectrometer.
Energetic neutron measurements remain a challenge for space science investigations and radiation monitoring for human exploration beyond LEO. We are investigating a new composite scintillator design that uses Li6 glass scintillator embedded in a PVT block. A comparison between Li6 and Boron 10 loaded scintillators are being studied to assess the advantages and shortcomings of these two techniques. We present the details of the new Li6 design and results from the comparison of the B10 and Li6 techniques during exposures in a mixed radiation field produced by high energy protons interacting in a target material.
The detectors were fabricated from a Ge:Ga wafer from Eagle-Pitcher with a room temperature resistivity of approx. 12ohms cm. The wafer is approximately 2 inches in diameter and 0.061 inches thick. The contact material was ion implanted with Boron using 10 to the 14th power ions/sq cm at 25 Kev and 2 x10 to the 14th power ions/sq cm at 50 Kev. The crystal was then sputter-cleaned and metallized first with sputtered Ti and then sputter Au. In addition to the usual infrared measurements of responsivity and noise, measurements were made of the detectors' response to ionizing radiation.
The relative abundances of cosmic-ray nuclei in the charge range boron through nickel over the energy range 1-10 GeV per amu were measured with a balloon-borne detector. The instrument consists of a scintillation and Cerenkov counter telescope with a multiwire proportional chamber hodoscope and has been flown in four high-altitude balloon flights. Good charge resolution (sigma = 0.2 charge units at iron) and high statistical accuracy have been achieved. These data are used to derive the energy dependence of the leakage path length using the leaky box model of propagation and confinement in the galaxy. This energy dependence is found to be best fit by lambda = E(tot) exp -n, where n = 0.49 + or - 0.06 over 1-10 GeV per amu. Relative abundances at the source are consistent with an energy-independent composition.
Explore the source record for details and available documents.
Several new types of back surface field (BSF) cells were designed and fabricated. These include boron and phosphorus diffused BSF cells, single crystal epitaxially grown BSF cells and chemically vapor deposited (CVD) polycrystalline BSF cells. Boron diffusion yielded 10 ohm-cm BSF cells with 0.6 volt open-circuit voltages and collection efficiencies equal to those previously reported for aluminum alloying. The epitaxially grown cells also exhibited high open-circuit voltages and collection efficiencies and may be more radiation damage resistant. The polycrystalline cells had very high internal series resistance. No direct relationship was found to exist between collection efficiency and open-circuit voltage, V sub oc in BSF cells. Results indicate that the V sub oc effect is not caused simply by the mechanism of blocking of minority carriers.
Several new types of back surface field (BSF) cells were designed and fabricated. These include boron and phosphorus diffused BSF cells, single crystal epitaxially grown BSF cells and chemically vapor deposited (CVD) polycrystalline BSF cells. Boron diffusion yielded 10 ohm-cm BSF cells with 0.6 volt open-circuit voltages and collection efficiencies equal to those previously reported for aluminum alloying. The epitaxially grown cells also exhibited high open-circuit voltages and collection efficiencies and may be more radiation damage resistant. The polycrystalline cells had very high internal series resistance. No direct relationship was found to exist between collection efficiency and open-circuit voltage in BSF cells.
An experimental investigation was made of the application of holographic interferometry to the nondestructive detection of unbonded areas (flaws) in bonded panels. Flaw detection results were compared with results obtained with an ultrasonic flaw detector. Holography, with panel deformation accomplished by a reduction in ambient pressure, is less sensitive for flaws beneath 5 and 10 plies of boron-epoxy than the ultrasonic method, though it does have its operational advantages. A process for the manufacture of bonded panels which incorporate known unbonded areas was also developed. The unbonded areas were formed without the use of foreign materials, which makes the method suitable for the construction of reference standards for bonded panels whenever needed for the proper setup of ultrasonic flaw-detection instruments.
Boron (dose, 2 x 10 to the 17th ions/sq cm) was implanted into high purity iron, AISI 316 austenitic stainless steel, and AISI 440C martensitic stainless steel, at 40 keV. The film structure of implanted samples was examined and characterized by contrast and diffraction analyses utilizing transmission electron microscopy. The effect of B(+) ion implantation on the corrosion behavior was studied using the potentiodynamic polarization technique. Tests were performed in deaerated 1 N H2SO4 and 0.1 M NaCl solutions. Scanning electron microscopy was used to examine the morphology of the corroded surfaces after testing.
The feasibility of a novel p(+)-Si(1-x)Ge(x)-p-Si heterojunction internal photoemission (HIP) IR detector is demonstrated. A degenerately doped p(x)-Si(1-x)Ge(x) layer is required for strong IR absorption to generate photoexcited holes. The Si(1-x)Ge(x) layers are grown by molecular beam epitaxy, with boron concentrations up to 10 to the 20th/cu cm achieved by using an HBO2 source. Photoresponse at wavelengths ranging from 2 to 10 microns has been obtained with quantum efficiencies above 1 percent. The tailorable cutoff wavelength of the HIP detector has been demonstrated by varying the Ge composition ratio in the Si(1-x)Ge(x) layers.
PtSi/Si Schottky-barrier devices detecting long-wavelength infrared (LWIR) photons demonstrated. Essential feature of one of these devices is p+ "doping spike"; layer of Si about 10 Angstrom thick, located at PtSi/Si interface, and doped with electron acceptors (boron atoms) at concentration between 5 x 10(19) and 2 x 10(20) cm(-3). Doping spikes extend cutoff wavelengths of devices to greater values than otherwise possible.
The assumption that boron is a moderately volatile element is examined. It was demonstrated that interior pieces of chondrites contain significantly less boron than had been thought to be indigenous to this type of meteorite. The mean and range of boron abundances in 16 internal pieces of 10 chondrites were significantly smaller than in 126 pieces of 40 chondrites with unknown terrestrial histories. A new value of the cosmic abundance of boron was determined using the geometric average of the results from interior pieces of 10 chondrites. Based upon the thermodynamic assessment of the cosmochemical properties of boron by Cameron, et al. Anders and Ebihara assumed that boron was a moderately volatile element. They renormalized the data of Curtis et al. to a chondrule free basis and thus inferred that the cosmic abundance of boron was about 3 times greater than that proposed by Curtis, et al. To resolve these differences in data, the relative abundances of several elements including boron were measured in 38 carefully prepared interior pieces of 26 different chondrites. Correlation between boron and sulfur abundances, indicate that, contrary to the conclusions of Cameron, et al., boron is not a moderately volatile element.
The work performed over the period of September 1971 to August 1972 to develop production processes for fabrication of lithium doped P/N cells is described. The BCl3 diffusion without 02 was selected as the optimum diffusion process for fabrication of lithium doped cells. An 8-2-7 (warm up - deposition - drive-in time in minutes) diffusion schedule at 1055 C was used for the first two lots (300 cells each) delivered to JPL. Cell efficiencies ranged from 11.0 to 13.7% based on an AMO of 135.3 mW/sq cm. These high efficiencies were obtained using from 10 to 40 cells per boron diffusion; increasing the quantity beyond 40 resulted in lower outputs. At this point, the emphasis was placed on investigation of a BCl3 with 02 diffusion. Through evaluation of the effects of diffusion time and temperature, gas flow rates, and desposition plus drive-in vs. continuous deposition and no drive-in cycles, diffusion parameters were determined which produced short circuit currents of 136 + or - 4 mA for ten cells spaced along 12 in. of the diffusion boat. The quantity was increased to 60, 100, and 150 cell diffusions with no more variation in cell short circuit current than observed with 10 cells.
Preliminary results of the Applications Technology Satellite-6 (ATS-6) solar cell flight experiment to isolate and identify solar cell degradation mechanisms resulting from particulate radiation and to obtain specific design data applicable to extended synchronous spacecraft missions are presented. The experiment includes 80 individual cells representing 16 different solar cell/cover glass configurations. Most of the cells are 0.030 cm thick boron doped n/p cells with 10 ohm cm resistivity and solder-coated AgTi contacts. The voltage-current characteristics were measured regularly. The data for the first 325 days of flight show short circuit currents 1-8% higher than measurements made with solar simulations. Maximum power varied between -1 and +6%. After 50 days in orbit the degradation of short circuit current due to ultraviolet effects was determined to be about 2%. All cells except those with fluorinated ethylene propylene covers performed well after 325 days.
The Dow Corning process consists of the carbothermic reduction of silica to produce silicon that is then purified by unidirectional solidification. The process has produced silicon of semiconductor quality with respect to all elements except boron and phosphorus at about 10 ppma and aluminum at 0.1 ppma. Solar cells produced from this silicon gave AM0 conversion efficiencies of 11%. A process cost analysis is presented.
Silicon: Gallium infrared detector assemblies were designed, fabricated, and tested using techniques representative of those employed for hybrid arrays to determine the suitability of this candidate technology for infrared astronomical detector array applications. Both the single channel assembly and the assembly using a 32 channel CMOS multiplexer are considered. The detector material was certified to have a boron background of less than 10 to the 13th power atoms/sq cm counter doped with phosphorus. The gallium concentration is 2 x 10 to the 16th power atoms/cu cm.
Low-energy ion implantation processes for the automated production of silicon solar cells were investigated. Phosphorus ions at an energy of 10 keV and dose of 2 x 10 to the 15th power/sq cm were implanted in silicon solar cells to produce junctions, while boron ions at 25 keV and 5 x 10 to the 15th power were implanted in the cells to produce effective back surface fields. An ion implantation facility with a beam current up to 4 mA and a production throughput of 300 wafers per hour was designed and installed. A design was prepared for a 100 mA, automated implanter with a production capacity of 100 MW sub e/sq cm per year. Two process sequences were developed which employ ion implantation and furnace or pulse annealing. A computer program was used to determine costs for junction formation by ion implantation and various furnace annealing cycles to demonstrate cost effectiveness of these methods.