Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “BODIES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Comparing attitude control effectiveness for actuators on two bodies of a six body model of a flexible spacecraft with that for actuators restricted to a single body

A ten rigid body model of a prototype flexible space platform was approximated by a six body model to facilitate comparison of attitude control effectiveness for actuators on two bodies with control effectiveness for actuators restricted to a single body of the same model. Actuators and sensors were found to be required on two of the six bodies for effective attitude control.

Chichester, F. D.↗
NASA NTRS1959

Transonic Aerodynamic Characteristics of a 45 deg Swept Wing Fuselage Model with a Finned and Unfinned Body Pylon Mounted Beneath the Fuselage or Wing, Including Measurements of Body Loads

An investigation of a model of a standard size body in combination with a representative 45 deg swept-wing-fuselage model has been conducted in the Langley 8-foot transonic pressure tunnel over a Mach number range from 0.80 to 1.43. The body, with a fineness ratio of 8.5, was tested with and without fins, and was pylon-mounted beneath the fuselage or wing. Force measurements were obtained on the wing-fuselage model with and without the body, for an angle-of-attack range from -2 deg to approximately 12 deg and an angle-of-sideslip range from -8 deg to 8 deg. In addition, body loads were measured over the same angle-of-attack and angle-of-sideslip range. The Reynolds number for the investigation, based on the wing mean aerodynamic chord, varied from 1.85 x 10(exp 6) to 2.85 x 10(exp 6). The addition of the body beneath the fuselage or the wing increased the drag coefficient of the complete model over the Mach number range tested. On the basis of the drag increase per body, the under-fuselage position was the more favorable. Furthermore, the bodies tended to increase the lateral stability of the complete model. The variation of body loads with angle of attack for the unfinned bodies was generally small and linear over the Mach number range tested with the addition of fins causing large increases in the rates of change of normal-force coefficient and nose-down pitching-moment coefficient. The variation of body side-force coefficient with sideslip for the unfinned body beneath the fuselage was at least twice as large as the variation of this load for the unfinned body beneath the wing. The addition of fins to the body beneath either the fuselage or the wing approximately doubled the rate of change of body side-force coefficient with sideslip. Furthermore, the variation of body side-force coefficient with sideslip for the body beneath the wing was at least twice as large as the variation of this load with angle of attack.

Wornom, Dewey E.↗
NASA NTRS1961

An Investigation of the Influence of Body Size and Indentation Asymmetry of the Effectiveness of Body Indentation in Combination with a Cambered Wing

An investigation has been made of a 450 sweptback cambered wing in combination with an unindented body and a body symmetrically indented with respect to its axes designed for a Mach number of 1.2. The ratio of body frontal area to wing planform area was 0.08 for these wing-body combinations. In order to determine the influence of body size on the effectiveness of indentation, the test data have been compared with previously obtained data for similar configurations having a ratio of body frontal area to wing planform area of 0.04. Also, in order to investigate the relative effectiveness of indentation asymmetry, a specially indented body designed to account for the wing camber and also designed for a Mach number of 1.2 has been included in these tests. The investigation was conducted in the Langley 8-Foot Tunnels Branch at Mach numbers from 0.80 to 1.43 and a Reynolds number of approximately 1.85 x 10(exp 6), based on a mean aerodynamic chord length of 5.955 inches. The data indicate that the configurations with larger ratio of body frontal area to wing planform area had smaller reductions in zero-lift wave drag associated with body indentation than the configurations with smaller ratio of body frontal area to wing planform area. The 0.08-area-ratio configurations also had correspondingly smaller increases in the values of maximum lift-drag ratio than the 0.04-area-ratio configurations. The consideration of wing camber in the body indentation design resulted in a 35.5-percent reduction in zero-lift wave drag, compared with a 21.5-percent reduction associated with the symmetrical indentation, but had a negligible effect on the values of maximum lift-drag ratio.

Patterson, James C., Jr.↗
NASA NTRS1984

Development and application of an analysis of axisymmetric body effects on helicopter rotor aerodynamics using modified slender body theory

A computationally efficient body analysis designed to couple with a comprehensive helicopter analysis is developed in order to calculate the body-induced aerodynamic effects on rotor performance and loads. A modified slender body theory is used as the body model. With the objective of demonstrating the accuracy, efficiency, and application of the method, the analysis at this stage is restricted to axisymmetric bodies at zero angle of attack. By comparing with results from an exact analysis for simple body shapes, it is found that the modified slender body theory provides an accurate potential flow solution for moderately thick bodies, with only a 10%-20% increase in computational effort over that of an isolated rotor analysis. The computational ease of this method provides a means for routine assessment of body-induced effects on a rotor. Results are given for several configurations that typify those being used in the Ames 40- by 80-Foot Wind Tunnel and in the rotor-body aerodynamic interference tests being conducted at Ames. A rotor-hybrid airship configuration is also analyzed.

Yamauchi, G.↗
NASA NTRS1958

Effects of Body Shape on the Drag of a 45 degree Sweptback-Wing-Body Configuration at Mach Numbers from 0.90 to 1.43

An investigation was made of the effects of body shape on the drag of a 45 deg sweptback-wing-body combination at Mach numbers from 0.90 to 1.43. Both the expansion and compression fields induced by body indentation were swept back as the stream Mach number increased from 0.94. The line of zero pressure change was generally tangent to the Mach lines associated with the local velocities over the wing and body. The strength of the induced pressure fields over the wing were attenuated with spanwise distance and the major effects were limited to the inboard 60 percent of the wing semispan. Asymmetrical body indentation tended to increase the lift on the forward portion of the wing and reduce the lift on the rearward portion. This redistribution of lift had a favorable effect on the wave drag due to lift. Symmetrical body indentation reduced the drag loading near the wing-body juncture at all Mach numbers. The reduction in drag loading increased in spanwise extent as the Mach number increased and the line of zero induced pressure became more nearly aligned with the line of maximum wing thickness. Calculations of the wave drag due to thickness, the wave drag due to lift, and the vortex drag of the basic and symmetrical M = 1.2 body and wing combinations at an angle of attack of 0 deg predicted the effects of indentation within 11 percent of the wing-basic-body drag throughout the Mach number range from 1.0 to 1.43. Calculations of the wave drag due to thickness, the wave drag due to lift, and the vortex drag for the basic, symmetrical M = 1.2, and asymmetrical M = 1.4 body and wing combinations predicted the total pressure drag to within 8 percent of the experimental value at M = 1.43.

Olstad, Walter B.↗
NASA NTRS1972

Effects of body shape on the aerodynamic characteristics of an all-body hypersonic aircraft configuration at Mach numbers from 0.65 to 10.6

An experimental investigation was conducted to determine the effects of several variations in body shape on the aerodynamic characteristics of an all-body hypersonic aircraft configuration. The basic configuration had a delta planform with an elliptic cone forebody and an afterbody of elliptic cross section terminating in a straight-line trailing edge. Variations in body shape included the ratio of maximum cross-sectional to body planform area, body leading-edge sweep, and forebody length ratio. In addition, the effects of a thin wing mounted on one of the bodies was investigated, and the aerodynamic characteristics of just the forebodies of two of the configurations were determined. The models had no stabilizing surfaces or propulsion system packages. Ranges of angle of attack (-4 deg to +15 deg) and angle of sideslip (-4 deg to +8 deg) were investigated. Of the four complete bodies, the configuration with the lowest ratio of cross-sectional to body planform area had the highest maximum lift-drag ratio and the greatest level of longitudinal stability at most Mach numbers. All the configurations had positive longitudinal stability near maximum lift-drag ratio at most Mach numbers. With exception of the lowest subsonic Mach numbers, changes in body sweep angle and in forebody length ratio had only minor effects on maximum lift-drag ratio.

Nelms, W. P., Jr.↗
NASA NTRS1984

Analysis of axisymmetric body effects on rotor aerodynamics using modified slender body theory

A modified slender body theory was used in modelling the flowfield around an axisymmetric body at zero angle of attack. The model was defined in an attempt to characterize body-induced effects on helicopter rotor performance and loading using efficient computation methods. The streamfunction for an axial source distribution was applied in the body model, which was then adapted to the helicopter analysis code (CAMRAD). The body-induced velocities were calculated for separate locations on the rotor disk. Three different rotor models in nonuniform inflow with a free wake geometry were considered. Comparison of predictions with data on ellipsoidal and axisymmetric bodies showed good agreement for moderately thick ellipsoidal bodies. Oscillatory blade bending moments were increased by the presence of the body, but overall performance impact was negligible. Computational efficiency was 10-20 percent better than with a potential flow panel code.

Yamauchi, G. K.↗
NASA NTRS1996

Upper Body Venous Compliance Exceeds Lower Body Venous Compliance in Humans

Human venous compliance hypothetically decreases from upper to lower body as a mechanism for maintenance of the hydrostatic indifference level 'headward' in the body, near the heart. This maintains cardiac filling pressure, and thus cardiac output and cerebral perfusion, during orthostasis. This project entailed four steps. First, acute whole-body tilting was employed to alter human calf and neck venous volumes. Subjects were tilted on a tilt table equipped with a footplate as follows: 90 deg, 53 deg, 30 deg, 12 deg, O deg, -6 deg, -12 deg, -6 deg, O deg, 12 deg, 30 deg, 53 deg, and 90 deg. Tilt angles were held for 30 sec each, with 10 sec transitions between angles. Neck volume increased and calf volume decreased during head-down tilting, and the opposite occurred during head-up tilt. Second, I sought to cross-validate Katkov and Chestukhin's (1980) measurements of human leg and neck venous pressures during whole-body tilting, so that those data could be used with volume data from the present study to calculate calf and neck venous compliance (compliance = (Delta)volume/(Delta)pressure). Direct measurements of venous pressures during postural chances and whole-body tilting confirmed that the local changes in venous pressures seen by Katkov and Chestukhin (1980) are valid. The present data also confirmed that gravitational changes in calf venous pressure substantially exceed those changes in upper body venous pressure. Third, the volume and pressure data above were used to find that human neck venous compliance exceeds calf venous compliance by a factor of 6, thereby upholding the primary hypothesis. Also, calf and neck venous compliance correlated significantly with each other (r(exp 2) = 0.56). Fourth, I wished to determine whether human calf muscle activation during head-up tilt reduces calf venous compliance. Findings from tilting and from supine assessments of relaxed calf venous compliance were similar, indicating that tilt-induced muscle activation is relatively unimportant. Low calf venous compliance probably results from stiffer venous, skeletal muscle, and connective tissues, and better-developed local and central neural controls of venous distensibility. This research establishes that upper-to-lower body reduction of venous compliance can explain headward positioning of the hydrostatic indifference level in humans.

Watenpaugh, Donald E.↗
NASA NTRS1959

Effect of Body Perturbations on Hypersonic Flow Over Slender Power Law Bodies

Hypersonic-slender-body theory, in the limit as the free-stream Mach number becomes infinite, is used to find the effect of slightly perturbing the surface of slender two-dimensional and axisymmetric power law bodies, The body perturbations are assumed to have a power law variation (with streamwise distance downstream of the nose of the body). Numerical results are presented for (1) the effect of boundary-layer development on two dimensional and axisymmetric bodies, (2) the effect of very small angles of attack (on tow[dimensional bodies), and (3) the effect of blunting the nose of very slender wedges and cones.

Mirels, Harold↗
DOE OSTI2026

Energy-Screened Many-Body Expansion for Protein–Ligand Interactions: Examining Convergence for Metalloenzymes Through Seven–Body Interactions

Fragment-based quantum chemistry is a powerful strategy for calculating protein−ligand interaction energies using quantum chemistry methods. Rigorous convergence often requires hundreds of atoms in the protein binding-site model, especially if that model is constructed using distance-based criteria to select amino acid residues, while three- and four-body calculations exhibit instability related to combinatorial proliferation in the number of subsystem calculations. Here, we report an energy-based screening protocol for the many-body expansion applied to protein−ligand interactions, implemented in the open-source FRAGME∩T code. Using a combination of aggressive screening based on semiempirical quantum chemistry, with an improved graph-theoretical algorithm to eliminate unimportant subsystems, we are able to perform n-body calculations up to n = 7 using density functional theory in triple-ζ basis sets. Distance cutoffs further reduce the cost without compromising accuracy. Rapid and stable convergence of the many-body expansion is obtained by n = 4, for a pair of metalloenzymes in which a divalent ion coordinates directly to the ligand. As compared to previous results that relied solely on distance cutoffs, oscillations in the n-body corrections are reduced or eliminated, although residual errors remain in one case. This work demonstrates that benchmark-quality protein−ligand interaction energies can be systematically converged using a method with excellent parallel efficiency and scalability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1990

Interactions between rigid-body and flexible-body motions in maneuvering spacecraft

The present consideration of the significant interactions between rigid-body and flexible-body motions in maneuvering spacecraft proceeds by distinguishing between the two types of motion on the basis of a tracking coordinate system which coincides with the rigid-body component of the motion, as well as by maintaining the motion relative to the tracking coordinate as orthogonal to the rigid-body motion. The elastic motion is excited by the rigid-body motion via Coriolis terms, angular acceleration terms, and centrifugal terms. These interactions are illustrated for spacecraft undergoing bidirectional elastic motions via the dynamics of constantly rotating free-free beams subject to combined bending and longitudinal vibration.

Silverberg, Larry M.↗
NASA NTRS1990

Energy absorption, lean body mass, and total body fat changes during 5 weeks of continuous bed rest

The nature of the body composition changes due to inactivity was examined together with the question of whether these changes are secondary to changes in energy absorption. Volunteers were 15 healthy males who lived on a metabolic research ward under close staff supervision for 11 weeks. Subjects were ambulatory during the first six weeks and remained in continuous bed rest for the last five weeks of the study. Six male volunteers (age 24-61 years) were selected for body composition measurements. Nine different male volunteers (age 21-50 years) were selected for energy absorption measurements. The volunteers were fed weighed conventional foods on a constant 7-d rotation menu. The average daily caloric content was 2,592 kcal. Comparing the five weeks of continuous bed rest with the previous six weeks of ambulation, it was observed that there was no change in energy absorption or total body weight during bed rest, but a significant decrease in lean body mass and a significant increase in total body fat (p less than 0.05).

Krebs, Jean M.↗
NASA NTRS1993

An experimental and analytical study of a lifting-body wind-tunnel model exhibiting body-freedom flutter

Flutter analysis of the proposed National Aerospace Plane indicates that in the subsonic to transonic flight regime, the vehicle may be susceptible to an instability known as body-freedom flutter. Body-freedom flutter is a dynamic instability involving a vehicle rigid-body mode coupling with one or more of the vehicle's elastic modes. In the case of the NASP, the body-freedom flutter predicted by analysis involves the short-period mode of the vehicle coupling with the pivot mode of the all-movable wings. A wind-tunnel test was designed to investigate this phenomenon. Parameter studies included variations in wing-actuator stiffness, wing-pivot shaft location along the root chord, and thickness of the fuselage. The wind-tunnel test was conducted in the NASA Langley Transonic Dynamics Tunnel. Flutter boundaries were measured in the wind tunnel for three configurations and a model divergence point was measured on a fourth configuration. At the last flutter point obtained during the test, body-freedom flutter proved to be rather violent. The analysis used in this study incorporated thin-wing theory aerodynamics and did a fairly good job of predicting the flutter boundaries.

Soistmann, David L.↗
NASA NTRS1960

Calculated Effects of Body Shape on the Bow-Shock Overpressures in the Far Field of Bodies in Supersonic Flow

A theory for the supersonic flow about bodies in uniform flight in a homogeneous medium is reviewed and an integral which expresses the effect of body shape upon the flow parameters in the far field is reduced to a form which may be readily evaluated for arbitrary body shapes. This expression is then used to investigate the effect of nose angle, fineness ratio, and location of maximum body cross section upon the far-field pressure jump across the bow-shock of slender bodies. Curves are presented showing the variation of the shock strength with each of these parameters. It is found that, for a wide variety of shapes having equal fineness ratios, the integral has nearly a constant value.

Lansing, Donald L.↗