Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “B20”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Impact of a Diesel High Pressure Common Rail Fuel System and Onboard Vehicle Storage on B20 Biodiesel Blend Stability

Adoption of high-pressure common-rail (HPCR) fuel systems, which subject diesel fuels to higher temperatures and pressures, has brought into question the efficacy of ASTM International specifications for biodiesel and biodiesel blend oxidation stability, as well as the lack of any stability parameter for diesel fuel. A controlled experiment was developed to investigate the impact of a light-duty diesel HPCR fuel system on the stability of 20% biodiesel (B20) blends under conditions of intermittent use and long-term storage in a relatively hot and dry climate. B20 samples with Rancimat induction periods (IPs) near the current 6.0-hour minimum specification (6.5 hr) and roughly double the ASTM specification (13.5 hr) were prepared from a conventional diesel and a highly unsaturated biodiesel. Four 2011 model year Volkswagen Passats equipped with HPCR fuel injection systems were utilized: one on B0, two on B20-6.5 hr, and one on B20-13.5 hr. Each vehicle was operated over a one-hour drive cycle in a hot running loss test cell to initially stress the fuel. The cars were then kept at Volkswagen's Arizona Proving Ground for two (35 degrees C average daily maximum) to six months (26 degrees C average daily maximum). The fuel was then stressed again by running a portion of the one-hour dynamometer drive cycle (limited by the amount of fuel in the tank). Fuel rail and fuel tank samples were analyzed for IP, acid number, peroxide content, polymer content, and ester profile. The HPCR fuel pumps were removed, dismantled, and inspected for deposits or abnormal wear. Analysis of fuels collected during initial dynamometer tests showed no impact of exposure to HPCR conditions. Long-term storage with intermittent use showed that IP remained above 3 hours, acid number below 0.3 mg KOH/g, peroxides low, no change in ester profile, and no production of polymers. Final dynamometer tests produced only small changes in fuel properties. Inspection of the HPCR fuel pumps revealed no deposits or abnormal wear for any fuel. The results provide some confidence that the ASTM D7467 stability requirement of 6 hr. minimum IP for B6 to B20 blends provides adequate protection for modern engine fuel systems.

30 DIRECT ENERGY CONVERSION↗

Diesel Particulate Filter Durability Performance Comparison Using Metals Doped B20 vs. Conventional Diesel Part II: Chemical and Microscopic Characterization of Aged DPFs

This project's objective was to generate experimental data to evaluate the impact of metals doped B20 on diesel particle filter (DPF) ash loading and performance compared to that of conventional petrodiesel. The effect of metals doped B20 vs. conventional diesel on a DPF was quantified in a laboratory controlled accelerated ash loading study. The ash loading was conducted on two DPFs - one using ULSD fuel and the other on B20 containing metals dopants equivalent to 4 ppm B100 total metals. Engine oil consumption and B20 metals levels were accelerated by a factor of 5, with DPFs loaded to 30 g/L of ash. Details of the ash loading experiment and on-engine DPF performance evaluations are presented in the companion paper (Part I). The DPFs were cleaned, and ash samples were taken from the cleaned material. X-ray Fluorescence (XRF), X-Ray Photoelectron Spectroscopy (XPS) and X-Ray Diffraction (XRD) were conducted on the ash samples. Core samples were taken from the cleaned DPF and were subjected to scanning electron microscope energy dispersive x-ray spectroscopy (SEM-EDS) and XRF analysis. A comparison of the data from the two DPFs is presented. The XRD and XPS analysis showed that the compounds present in the ash from the two DPFs were nearly identical, though differing in concentrations. CaSO4 was the biggest component of the ash from both DPFs. The metals doped B20 fuel resulted in ash with similar characteristics to that deposited by the lube oil and did not appear to have any deleterious physical effects on the DPF substrate (did not penetrate the substrate).

ADVANCED PROPULSION SYSTEMS,BIOMASS FUELS↗

Local structure and magnetic properties of B2- and B20-like ultrathin Mn films grown on Si(001)

The structural and magnetic properties of ultrathin Mn layers deposited onto Si(001) by molecular beam epitaxy at low temperature are reported. X-ray absorption fine structure studies reveal that the structure of the silicide layer that forms depends on the growth temperature of the capping layer. A capping layer grown at 200 C on 0.35-monolayer (ML) Mn results in a metastable MnSi phase with a B2-like (CsCl) structure, whereas a cap grown at room temperature on 0.5 ML followed by annealing at 200 C produces a lower coordinated MnSi phase with a B20-like structure. Increasing the Mn thickness from 0.5 to 4 monolayers does not trigger a structural transformation but drives the structure closer to MnSi-B20. The sample with B2-like structure has the largest Mn magnetic moment of 0.33 {mu}{sub B}/Mn at T = 2 K, and a Curie temperature T{sub c} above 250 K. MnSi-B20 layers showed lower moments and much lower T{sub c}'s, in line with those reported for MnSi-B20 thin films.

36 MATERIALS SCIENCE↗

Diesel Particulate Filter Durability Performance Comparison Using Metals Doped B20 vs. Conventional Diesel Part I: Accelerated Ash Loading and DPF Performance Evaluation

The project objective was to generate experimental data to evaluate the impact of metals doped B20 on DPF ash loading and performance compared to that of conventional petrodiesel. Accelerated ash loading was conducted on two DPFs - one exposed to regular diesel fuel and the other to B20 containing metal dopants equivalent to 4 ppm B100 total metals (currently total metals are limited to 10 ppm in ASTM D6751, the standard for B100). Periodic performance evaluations were conducted on the DPFs at 10 g/L ash loading intervals. After the evaluations at 30 g/L, the DPF was cleaned with a commercial DPF cleaning machine and another round of DPF evaluations were conducted. A comparison of the effect of ash loading with the two fuels and DPF cleaning is presented. The metals doped B20 fuel resulted in ash that was similar to that deposited when exposed to ULSD (lube oil ash) and exhibited similar ash cleaning removal efficiency. Metals doped B20 resulted in faster ash accumulation within the DPF, as expected, but did not appear to have a negative effect on DPF pressure drop or regeneration rates (up to 30 g/L of ash) or exhibit deleterious physical effects on the DPF substrate.

ADVANCED PROPULSION SYSTEMS,BIOMASS FUELS↗

Chiral Magnetism and High-Temperature Skyrmions in B20-Ordered Co-Si

Magnets with chiral crystal structures and helical spin structures have recently attracted much attention as potential spin-electronics materials, but their relatively low magnetic-ordering temperatures are a disadvantage. While cobalt has long been recognized as an element that promotes high-temperature magnetic ordering, most Co-rich alloys are achiral and exhibit collinear rather than helimagnetic order. Crystallographically, the B20-ordered compound CoSi is an exception due to its chiral structure, but it does not exhibit any kind of magnetic order. Here, we use nonequilibrium processing to produce B20-ordered Co 1+ x Si 1₋ x with a maximum Co solubility of x = 0.043. Above a critical excess-Co content x c = 0.028 ), the alloys are magnetically ordered, and for x = 0.043, a critical temperature $T_c$ = 328 K is obtained, the highest among all B20-type magnets. The crystal structure of the alloy supports spin spirals caused by Dzyaloshinskii-Moriya interactions, and from magnetic measurements we estimate that the spirals have a periodicity of about 17 nm. In this work, our density-functional calculations explain the combination of high magnetic-ordering temperature and short periodicity in terms of a quantum phase transition where excess-cobalt spins are coupled through the host matrix.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

ULSD and B20 Hydrocarbon Impacts on EGR Cooler Performance and Degradation

Exhaust gas recirculation (EGR) cooler fouling has emerged as an important issue in diesel engine development. Uncertainty about the level of impact that fuel chemistry may have upon this issue has resulted in a need to investigate the cooler fouling process with emerging non-traditional fuel sources to gage their impact on the process. This study reports experiments using both ultra-low sulfur diesel (ULSD) and 20% biodiesel (B20) at elevated exhaust hydrocarbon conditions to investigate the EGR cooler fouling process. The results show that there is little difference between the degradation in cooler effectiveness for ULSD and B20 at identical conditions. At lower coolant temperatures, B20 exhibits elevated organic fractions in the deposits compared with ULSD, but this does not appear to lead to incremental performance degradation under the conditions studied. Comparisons with a previous study conducted at low HC levels shows that the presence of increased volatiles in the deposit does not impact the degradation in effectiveness significantly. Moreover, the effectiveness loss divided by the deposit mass gain for both low- and high-HC conditions seems to indicate that the HC fraction in the deposit does not significantly alter the overall thermal properties of the deposit layer.

33 ADVANCED PROPULSION SYSTEMS↗

St. Louis Metro Biodiesel (B20) Transit Bus Evaluation: 12-Month Final Report

The St. Louis Metro Bodiesel Transit Bus Evaluation project is being conducted under a Cooperative Research and Development Agreement between NREL and the National Biodiesel Board to evaluate the extended in-use performance of buses operating on B20 fuel. The objective of this research project is to compare B20 and ultra-low sulfur diesel buses in terms of fuel economy, veicles maintenance, engine performance, component wear, and lube oil performance.

09 BIOMASS FUELS↗

Structural properties and recrystallization effects in ion beam modified B20-type FeGe films

Disordered iron germanium (FeGe) has recently garnered interest as a testbed for a variety of magnetic phenomena as well as for use in magnetic memory and logic applications. This is partially owing to its ability to host skyrmions and antiskyrmions—nanoscale whirlpools of magnetic moments that could serve as information carriers in spintronic devices. In particular, a tunable skyrmion–antiskyrmion system may be created through precise control of the defect landscape in B20-phase FeGe, motivating the development of methods to systematically tune disorder in this material and understand the ensuing structural properties. To this end, we investigate a route for modifying magnetic properties in FeGe. In particular, we irradiate epitaxial B20-phase FeGe films with 2.8 MeV Au 4+ ions, which creates a dispersion of amorphized regions that may preferentially host antiskyrmions at densities controlled by the irradiation fluence. To further tune the disorder landscape, we conduct a systematic electron diffraction study with in situ annealing, demonstrating the ability to recrystallize controllable fractions of the material at temperatures ranging from ~150 to 250°C. Finally, we describe the crystallization kinetics using the Johnson–Mehl–Avrami–Kolmogorov model, finding that the growth of crystalline grains is consistent with diffusion-controlled one-to-two dimensional growth with a decreasing nucleation rate.

36 MATERIALS SCIENCE↗

Unusual magnetoresistance in cubic B20 Fe 0.85 Co 0.15 Si chiral magnets

The B20 chiral magnets with broken inversion symmetry and C 4 rotation symmetry have attracted much attention. The broken inversion symmetry leads to the Dzyaloshinskii–Moriya that gives rise to the helical and Skyrmion states.Wereport the unusual magnetoresistance (MR) of B20 chiral magnet Fe 0.85 Co 0.15 Si that directly reveals the broken C 4 rotation symmetry and shows the anisotropic scattering by Skyrmions with respect to the current directions. The intimacy between unusual MR and broken symmetry is well confirmed by theoretically studying an effective Hamiltonian with spin–orbit coupling. In conclusion, the unusual MR serves as a transport signature for the Skyrmion phase.

36 MATERIALS SCIENCE↗

Possible quadrupole-order-driven commensurate-incommensurate phase transition in B20 CoGe

For this study, the B20-type cobalt germanide CoGe was investigated by measuring the specific heat, resistivity, and 59 Co nuclear magnetic resonance (NMR). We observed a phase transition at T Q = 13.7 K, evidenced by a very narrow peak of the specific heat and sharp changes of the nuclear spin-spin (T 2 –1 ) and spin-lattice ( T 1 – 1 ) relaxation rates. The fact that the entropy release is extremely small and the Knight shift is almost independent of temperature down to low temperatures as anticipated in a paramagnetic metal indicates that the T Q transition is of nonmagnetic origin. In addition, we detected a crossover scale T 0 ~ 30 K below which the resistivity and the NMR linewidth increase, and T 1 –1 is progressively distributed in space, that is, a static and dynamical spatial inhomogeneity develops. While the order parameter for the T Q transition remains an open question, a group-theoretical analysis suggests that the finite electric quadrupole density arising from the low local site symmetry at cobalt sites could drive the crystal symmetry lowering from the P2 1 3 symmetry that is commensurate to the R3 symmetry with an incommensurate wave vector, which fairly well accounts for the T Q transition. The quadrupole-order-driven commensurate-incommensurate phase transition may be another remarkable phenomenon arising from the structural chirality inherent in the noncentrosymmetric B20 family.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

2008 B20 Survey Results (Presentation)

Describes results of a sample survey of the quality of B20, a biodiesel blend, collected from U.S. public pumps and fleets as part of a joint effort by NREL, the NBB, and engine manufacturers.

02 PETROLEUM↗

Magnetic moments and spin structure in single-phase B20 Co 1+x Si 1-x (x = 0.043)

Neutron powder diffraction (NPD) and x-ray magnetic circular dichroism (XMCD) spectroscopy are employed to investigate the magnetism and spin structure in single-phase B20 Co 1.043 Si 0.957 . The magnetic contributions to the NPD data measured in zero fields are consistent with the helical order among the allowed spin structures derived from group theory. The magnitude of the magnetic moment is (0.3 ± 0.1) μ B /Co according to NPD, while the surface magnetization probed by XMCD at 3 kOe is (0.18–0.31) μ B /Co. Both values are substantially larger than the bulk magnetization of 0.11 μ B /Co determined from magnetometry at 70 kOe and 2 K. Finally, these experimental data indicate the formation of a helical spin phase and the associated conical states in high magnetic fields.

36 MATERIALS SCIENCE↗

B20 to B100 Blends as Heating Fuels

Biodiesel is mono-alkyl esters of long chain fatty acids derived from naturally occurring oils or fats which conform to ASTM D6751 specifications. Biodiesel refers to the pure fuel before blending with traditional distillate type petroleum-based fuels such as diesel fuel or home heating oil (petrodiesel). Biodiesel blends are denoted as, "BXX" with "XX" representing the percentage of biodiesel by volume contained in the blend (i.e.: B20 is 20% biodiesel, 80% petrodiesel). Biodiesel offers a near-term opportunity to displace petroleum-based heating oil with a low carbon, renewable fuel. Biodiesel can be made from a variety of domestically produced oils and fats such as commonly available vegetable oils or animal fats as well as other oils such as used frying oils, reclaimed distillers corn oil from ethanol plants, algal oils, etc. In the US, about half the biodiesel is made from soybean oil, with the remainder about evenly split between canola oil, animal fats, used cooking oils, and distillers corn oil.

09 BIOMASS FUELS↗