Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “As-cast microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

18 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Microstructural stability and mechanical properties of the as-cast and heat-treated newly developed TiNbCrTa refractory complex concentrated alloy

In this study, a TiNbCrTa refractory complex concentrated alloy (RCCA) was prepared using vacuum arc remelting. The microstructural evolution and mechanical properties of both as-cast and heat-treated RCCA samples were analyzed. Heat treatment (HT) was performed at 800–1200 °C for 1 h in a vacuum-sealed environment. These samples exhibited a formation of Cr 2 Nb and Cr 2 Ti Laves phases. A variation in elemental distribution was observed, with interdendritic (ID) regions showing higher fractions of Ti and Cr, while the dendritic regions had a greater concentration of Ta and Nb. Micro-segregation at the IDs was confirmed through energy dispersive x-ray spectroscopy mapping, which inferred the formation of Cr- and Ti-rich phases during HT at 800–1200 °C. High-temperature HT at 1200 °C for 1 h led to the evolution of the hcp omega phase. Prolonged HT at 1200 °C for 96 h resulted in the evolution of a Cr-rich Laves phase (Cr 2 Ta), which was homogeneously distributed within the microstructure, indicating an unstable microstructure. Furthermore, despite prolonged HT, a variation in the elemental distribution persisted due to the presence of dendritic and ID regions. Electron backscattered diffraction analysis revealed the presence of bcc and hcp phases in the dendritic and ID regions, respectively, of the as-cast and HTed samples. The as-cast samples demonstrated a high compressive strength of approximately 2 GPa. Micro-hardness values increased with the HT temperature up to 1000 °C. Further increases under HT conditions did not significantly reduce the microhardness value, whereas prolonged HT at 1200 °C led to an increase in the microhardness value. Overall, the newly developed TiNbCrTa RCCA exhibited high-strength behavior even after the phase transformation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Oxygen Effects and Selective Oxidation of Group IV Alloying Additions in Group V-Based Refractory Multi-principal Element Alloys

Refractory multi-principal element alloys (RMPEAs) hold significant potential for advancing ultra-high-temperature technologies due to their remarkable strength retention under these conditions. However, the beneficial effects of alloying on microstructural evolution and mechanical properties are often obscured by the presence of interstitial alloying elements. The intricate interactions between substitutional alloying elements of Groups IV, V, and VI and interstitial content, whether intentional or incidental, remain poorly understood. In this study, we investigate the impact of dissolved oxygen on the microstructural evolution and stability of RMPEAs primarily composed of Group V elements, Nb and V, along with Group IV elements Ti, Zr, and Hf. We show that the strong affinity of oxygen for Group IV elements Zr and Hf leads to the internal precipitation of oxides during heat treatment, which competes with the homogenization of the as-cast dendritic microstructure. Here, we demonstrate that careful control and design of oxygen content and Group IV alloying additions are essential to minimize micro-segregation and prevent the detrimental precipitation of internal oxides. To address these challenges, we propose employing non-equilibrium solidification calculations to predict and optimize as-cast solidification structures, thereby reducing the reliance on homogenization processes.

Alloy design↗
DOE OSTI2026

A modified scheil approach for nucleation-dependent solidification pathways

As-solidified microstructures of near-eutectic alloys often contain multiple primary phases that are not expected from equilibrium phase diagrams. Such microstructures are caused by cooling-rate-dependent solidification pathways, a factor not captured by the Scheil–Gulliver model or variations thereof. Here, we present a model and algorithm that incorporate the critical nucleation undercooling for each solid phase into the Scheil–Gulliver model. We hypothesize that the non-equilibrium microstructure formation is primarily governed by a nucleation-competition mechanism. This mechanism accounts for both stable/metastable phase selection and primary-phase formation within eutectic regions driven by asymmetric nucleation barriers. The model is validated against a hypereutectic Al-Fe alloy, where it successfully reproduces the observed microstructural constituents, revealing the key dependencies of solidification microstructure on nucleation kinetics. Applicability to multicomponent systems is demonstrated through a hypereutectic Al–Fe–Si ternary alloy, where the model successfully predicts divorced eutectic microstructures and the associated oscillatory solidification pathways along univariant lines. As a result, the proposed framework establishes a nucleation-dependent computational approach for interpreting and predicting solidification microstructures.

Alloy design↗
DOE OSTI2025

High Strength and Fracture Resistance of Reduced-Activity W-Ta-Ti-V-Zr High-Entropy Alloy for Fusion Energy Applications

Refractory high-entropy alloys (HEAs) are promising candidates for next-generation nuclear applications, particularly fusion reactors, due to their excellent high-temperature mechanical properties and irradiation resistance. Here, the microstructure and mechanical behavior were investigated for an equimolar WTaTiVZr HEA, designed from a palette of low-activation elements. The as-cast alloy exhibited a dendritic microstructure composed of W-Ta rich dendrites and Zr-Ti-V rich inter-dendritic regions, both possessing a body-centered cubic (BCC) crystal structure. Room temperature bulk compression tests showed ultra-high strength of around 1.6 GPa and plastic strain ~6%, with fracture surfaces showing cleavage facets. The alloy also demonstrated excellent high-temperature strength of ~650 MPa at 500 °C. Scratch-based fracture toughness was ~38 MPa√m for the as-cast WTaTiVZr HEA compared to ~25 MPa√m for commercially used pure tungsten. This higher value of fracture toughness indicates superior damage tolerance relative to commercially used pure tungsten. These results highlight the alloy’s potential as a low-activation structural material for high-temperature plasma-facing components (PFCs) in fusion reactors.

Physics↗
DOE OSTI2025

A critical analysis of U-Pu-Zr phase transitions using calorimetric, microstructural, and phase equilibria data

Metallic fuels consisting primarily of uranium, plutonium, and zirconium (U-Pu-Zr) are a leading material candidate for fast-spectrum nuclear reactors. Early demonstration programs proved the principle of safe and efficient fast reactor operation, however there is still considerable uncertainty regarding the phase equilibria and microstructural evolution across the ternary composition space. Quantitative phase formation and identification measurements are scarce and often incomplete, with studies reporting either phase transition temperatures or phase identification data, but not both from the same specimens. In this study, we critically compared experimental and calculated phase transition data and correlated with the microstructure and phase characterization data of as-cast and annealed U-Pu-Zr alloys. Differential scanning calorimetry (DSC) was used to measure phase transitions in the subsolidus regions (723−948 K) of three ternary U-Pu-Zr alloys with similar plutonium concentrations but various U/Zr ratios. Due to sluggish kinetics and narrow ranges of phase stability, complex peaks required the use of a Frazier-Suzuki peak fitting algorithm to deconvolute and calculate transition peak temperatures and enthalpies. We also identified trends of phase transition behavior by critically comparing our DSC data with previous phase transition measurements as well as historical and calculated phase equilibrium diagrams. In conclusion, this provides a critical approach for benchmarking and assessing the quality of new U-Pu-Zr phase equilibria data prior to its incorporation into nuclear material databases.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Strong, ductile, and hierarchical hetero-lamellar-structured alloys through microstructural inheritance and refinement

The strength−ductility trade-off exists ubiquitously, especially in brittle intermetallic-containing multiple principal element alloys (MPEAs), where the intermetallic phases often induce premature failure leading to severe ductility reduction. Hierarchical heterogeneities represent a promising microstructural solution to achieve simultaneous strength−ductility enhancement. However, it remains fundamentally challenging to tailor hierarchical heterostructures using conventional methods, which often rely on costly and time-consuming processing. Here, we report a multiscale microstructural inheritance and refinement strategy to process “structural hierarchy precursors” in as-cast heterogeneous Al 0.7 CoCrFeNi MPEAs, which lead directly to a hierarchical hetero-lamellar structure (HLS) after simple rolling and annealing. Interestingly, it takes only 10 min of annealing time, two orders of magnitude less than that required to render the state-of-the-art properties during conventional processing of Al 0.7 CoCrFeNi, for us to achieve record-high strength−ductility combinations via the hierarchical HLS design that sequentially stimulates multiple unusual deformation and reinforcement mechanisms. In particular, the HLS-enabled high hetero-deformation-induced (HDI) internal stress triggers profuse <111>-type dislocations on over five independent slip systems in the supposedly brittle intermetallic phase and activates extensive stacking faults (SFs) and nanotwinning in the adjoining soft phase with a rather high SF energy. These unexpected, dynamically reinforcing hetero-deformation mechanisms across multiple length scales facilitate high sustained HDI strain hardening, along with a salient microcrack-mediated extrinsic ductilization effect, suggesting that the proposed microstructural inheritance and refinement strategy provides an efficient, fast, and low-cost approach to overcome the strength−ductility trade-off in a broad range of structural materials.

Science & Technology - Other Topics↗
DOE OSTI2025

Homogenization of Dendritic Structures and the High-Temperature Strength of the Refractory High-Entropy Alloy MoNbTaVW

MoNbTaVW, a pioneering refractory high-entropy alloy (RHEA), is renowned for its exceptional strength at elevated temperatures. Like most RHEAs, it solidifies into a dendritic microstructure with steep concentration gradients, necessitating heat treatment for equilibration. Steep concentration gradients typically complicate mechanical property analysis and modeling, key challenges for high-throughput alloy discovery. This study examines the effects of high-temperature homogenization (1800 °C for 8 hours) on the microstructure and mechanical properties of MoNbTaVW across temperatures up to 1200 °C. Postmortem microstructural analysis, coupled with chemical, crystallographic, and mechanical assessments, revealed that yield strength was surprisingly insensitive to homogenization, with less than a 3 pct difference between as-cast and heat-treated materials. Nanoindentation confirmed minimal nanohardness changes across the dendritic structure at room temperature. However, homogenization significantly enhanced high-temperature work hardening, producing higher peak compressive strength. Both as-cast and homogenized MoNbTaVW exhibited room-temperature strengths of 1400 MPa, exceeding previously reported values. These findings demonstrate that high-temperature treatment enables microstructural homogenization without compromising strength, a unique behavior among RHEAs. In conclusion, while not universally applicable, this insight highlights the importance of understanding microstructural development in experimental alloys and offers a pathway to design alloys that achieve homogeneous-like properties without heat treatment.

Rietema, C. J. [Lawrence Livermore National Labora↗
DOE OSTI2024

Systematic discovery of new nano-scale metastable intermetallic eutectic phases in laser rapid solidified Aluminum-Germanium alloy

Laser surface remelting of as-cast Al-Ge eutectic alloy is shown to produce ultrafine lamellar eutectic morphology with interlamellar spacing refined up to ∼60 nm and composed of FCC Al solid solution and unusual Al x Ge y intermetallic phases that do not form during near-equilibrium solidification. The microstructures are characterized and analyzed using a combination of selected area electron diffraction, high-resolution scanning transmission electron microscopy, energy dispersive X-ray spectroscopy to obtain high-resolution elemental maps, and atomistic modeling using density functional theory followed by atomic-scale image simulation. Depending on the local solidification conditions, the crystallography of the Al x Ge y intermetallic phases in the eutectic microstructure is either monoclinic (C 2/c) or monoclinic (P 2 1 ), with high densities of defects in both cases. This is in sharp contrast to the as-cast alloys that showed nominally pure Al and Ge phases with significant solute partitioning and equilibrium FCC and diamond cubic crystal structures, respectively. Corresponding kinetic phase diagrams are proposed to interpret the evolution of nano-lamellar eutectic morphologies with equilibrium Al and metastable Al x Ge y phases, and to explain increased solid solubility in the Al phases manifested by precipitation of ultrafine clusters of Ge. Furthermore, the reasons for the formation of these metastable eutectics under laser rapid solidification are discussed from the perspective of the competitive growth criterion.

Al-Ge eutectic↗
DOE OSTI2025

Creation of Self-Semi-Interpenetrating Network Structures in PIM-1 Membranes for Enhanced Physical Aging Resistance

A series of self-semi-interpenetrating network (ssIPN) thin films based on PIM-1 structure were developed by end-cross-linking telechelic PIM-1 oligomers end-capped with curable carboxylic acid groups to form model networks, which are penetrated by linear high-molecular-weight PIM-1 chains. ssIPN films with systematically varied network content ranging from 10 to 30 wt % were comprehensively examined on their microstructure and gas permeation properties. Fresh PIM-1 ssIPN films exhibited gas separation performances close to those of as-cast linear PIM-1, where the films closely followed the upper bound trade-off line, gaining as much selectivity as they lose gas permeability as the network content increases. This indicates that gas permeability is largely preserved despite cross-linking. Wide-angle X-ray scattering supported this observation, with peaks shifting toward lower d-spacing as oligomer content increased, suggesting tighter chain packing with higher cross-linkable oligomer loading. In physical aging studies over two months, all ssIPN films outperform linear PIM-1 for H 2 /CH 4 and O 2 /N 2 separations. Notably, the PIM-1 ssIPN with 10 wt % network content showed the best physical aging resistance, with negligible permeability loss even after one month. Finally, these findings highlight a promising macromolecular strategy for enhancing the physical aging resistance of microporous polymer membranes for gas separation.

PIM-1↗
DOE OSTI2024

Thermal stability and coarsening of eutectic and near-eutectic Ni–Ce alloys

Ni–Ce alloys are currently being studied as a castable alternative to conventional Ni-based superalloys. To understand the evolution of microstructure and mechanical behavior at elevated temperatures, this study investigates the mechanism of coarsening behavior in eutectic and near eutectic Ni–Ce at 900 °C. The as-cast eutectic Ni–Ce consists of a combination of fine lamellar and rod eutectic colonies with coarser boundary regions. Upon annealing, continuous coarsening, via process of globularization, initiates at colony boundaries or primary dendrites where faults (termination and branches) in the lamellar structure are plentiful. Coarsening then proceeds by a combination of fault migration mechanism and lamellar boundary splitting, growing toward the center of the eutectic colonies with increasing annealing time. Coarsening near the center of a colony is extremely slow, indicating the eutectic microstructure itself is very stable. Here, the near-eutectic alloys containing primary dendrites coarsen and stabilize faster compared to the fully eutectic alloy. Moreover, an anomaly is observed in the hardness of the fully eutectic alloy after long exposure at elevated temperature compared to the near-eutectic alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Microstructural Engineering of Cu-Rich Nanoprecipitate formation in NiCoFeCrCu0.12 High-Entropy Alloy via Severe Plastic Deformation for Enhanced Irradiation Tolerance

This study demonstrates a defect-engineering approach for controlling Cu-rich precipitates in FeNiCrCoCu0.2 high-entropy alloys (Cu-HEAs), delivering a novel pathway for next-generation nuclear reactor materials with superior irradiation resistance. This work establishes that severe plastic deformation (SPD) processing via Shear Assisted Processing and Extrusion (ShAPE) and Friction Stir Layer Deposition (FSLD) creates dense dislocation networks and subgrain boundaries that fundamentally alter precipitation behavior under identical thermal treatments. Atom probe tomography (APT) indicates that SPD produces a metastable, atomically homogeneous solid solution that, upon moderate heat treatment (500°C/10 hour), develops remarkedly stronger Cu clustering than the as-cast counterpart. High-temperature exposure (800°C/100 h) produces near-pure Cu precipitates (~90 at% Cu) with significantly enhanced defect-sink efficacy in SPD-processed alloys: precipitate sizes of 50-60 nm and number densities of 2.7-3.8 × 10¹7 m?³, compared to 89 nm and 0.44 × 10¹7 m?³ in as-cast materials. Collectively, the findings establish defect-mediated precipitation control as a scalable, high-impact route to tailor sink density and distribution in HEAs, enabling microstructures optimized for irradiation tolerance and mechanical robustness in nuclear reactor environments.

Meher, Subhashish↗
DOE OSTI2025

Macro-micro multiscale modeling to assist the design of HPDC Al castings microstructure and alloys for EV super-large body structures (Phase 1)

Implementation of High Pressure Die Casting (HPDC) Aluminum (Al) body structures for high volume electrified vehicles (EV) to improve electric efficiency remains a key strategy within many original equipment manufacturer (OEM)s. In addition to high strength for safety requirements, superior Self-Piercing Riveting (SPR) performance is demanded for HPDC Al alloys to be compatible with high volume SPR joining. In this work, it is proposed to extend and validate an existing Contractor finite element multiscale macro-micro modeling approach to quantify the influence of the microstructure of HPDC alloys on the fracture strain/displacement under 3-point bend and clinch testing. The success of this work will allow to replace solution treatment stage with low energy consumption heat treatment (HT) processes, or to design new non heat treatable (NHT) HPDC Al alloys to eliminate HT requirements. Ultimately, this project will facilitate the application of HPDC Al alloys for super-large vehicle structures to significantly reduce vehicle weight, and thus improving energy efficiency. The purpose of this project is to extend and validate an existing finite element code, which is based on the Contractor developed macro-micro multi-scale modeling approach, to numerically simulate the three-point bending and clinch test and study the influences of material microstructural characteristics and phase properties on the rivetability. The macro-micro modeling approach begins with a sample scale model and identify the location, which is mostly prone to failure, the deformation history of the boundaries of that location calculated will be used to drive a microstructure-based sub-models where the material microstructure and microscale properties are considered. Using this approach, the wrap-bending failure for two Al alloys are correctly predicted for the first time. This will start with phase I effort of building a framework of macro-micro three point bending test and clinch test of Al10SiMgMn HPDC alloy in the as-cast and T7 heat treated conditions. Those results will then be validated with experimental test results. The phase II effort will involve the utilization of the knowledge learned in phase I to establish the quantitative correlation between the microstructure characteristics and the riveting performance, which will be further used to guide the optimization of HPDC Al alloy microstructure using heat treatment process to achieve sufficient rivetability to join large thin-wall HPDC alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Conversion of real-world aluminum scrap streams into high-performance Al–Mg–Si–Cu automotive alloys using shear assisted processing and extrusion

The conversion of post-consumer aluminum (Al) scrap into usable Al alloys without adding primary Al is challenging because of excess impurities. In this work, >99% post-consumer Twitch, used beverage cans (UBCs), and remelt scrap ingots (RSIs) were used as feedstock materials. As-cast and solution heat-treated feedstock billets were extruded using Shear Assisted Processing and Extrusion (ShAPE) at ~510°C, followed by press quenching. To explore the development of the microstructure, texture, and underlying mechanisms and how they contribute to the overall strengthening in as-extruded and artificially aged samples, scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD) were used to collect microstructure and texture data. The enhanced strength and ductility were corroborated with the microstructural features and crystallographic texture. Simple shear $\textrm{A}/\bar{\textrm{A}}$, $\textrm{A}_1^*/\textrm{A} _2^*$ texture components along with weak $\textrm{C}$ and $\textrm{B}/\bar{\textrm{B}}$ texture components were formed during extrusion; the texture was strengthened after heat treatment. The refined second-phase particles helped to retain the deformed microstructure and texture. The contributions of dislocation and precipitate strengthening were maximized when billets were solution-heat-treated prior to extrusion. This is attributed to the formation of effective supersaturated solid solutions during the ShAPE process, which precipitate out during the peak age treatment. Overall, the highest yield strength of 305 MPa, ultimate tensile strength of 350 MPa, and elongation of 12% were achieved in artificially aged samples, which are comparable to those of Al 6082-T6.

Al alloy↗
DOE OSTI2024

Microstructural refinement of an Al-Ce-Mg alloy via Shear Assisted Processing and Extrusion

Al-Ce alloys have attracted recent interest because of their high thermal stability due to the low solubility of Ce in the Al matrix. The Al 11 Ce 3 eutectic phase gives excellent strain hardening behavior and moderate high-temperature strength in the as-cast state. However, its strengthening effect is limited by its coarse as-cast structure. Therefore, alternative manufacturing methods such as additive manufacturing or equal channel angular pressing have been applied to refine the Al 11 Ce 3 phase to good effect. However, these techniques are both expensive and time-consuming. Therefore, this study aims to use Shear Assisted Processing and Extrusion (ShAPE), an emerging solid phase processing technique that is more easily scalable than the previously mentioned methods. ShAPE can produce useful cross-sections of an Al-8Ce-4Mg alloy while refining the Al 11 Ce 3 phase to produce a higher strength material. It was found that a low temperature ShAPE process can improve the room temperature yield strength by ~60 % compared to a binary Al-4Mg alloy. Additionally, the high-temperature yield strength of the Al-Ce alloys increased by 20%, with a simultaneous 15% improvement in ductility compared to the binary Al-Mg alloy. Finally, these results highlight the potential for ShAPE as a processing technique for Al-Ce alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2025

High-temperature stability and thermal expansion behavior of equi-atomic refractory multi-principal element alloys based on MoNbTi system for Gen IV reactor applications

The present study investigates the thermal stability and thermal expansion behavior of seven equi-atomic refractory multi-principal element alloys (MPEAs) based on the MoNbTi ternary system composed of low neutron absorption cross section elements. Through an integrated approach utilizing in-situ high-temperature X-ray diffraction (HT-XRD) in conjunction with differential scanning calorimetry (DSC), dilatometry and ageing heat treatment, the thermal stability of the MPEAs was comprehensively analyzed. In-situ HT-XRD experiment confirmed the stability of the room temperature phases up to 1000 °C with no peaks observed corresponding to additional phases in the HT-XRD patterns at 500, 800 and 1100 °C. DSC thermograms showed the absence of peaks up to 1000 °C, while peaks and valleys corresponding to exothermic and endothermic events were observed above 1000 °C. Coefficient of thermal expansion (CTE) derived from second order polynomial fitting of linear thermal expansion data from the dilatometry experiment showed linear increment up to 1000 °C for all the alloys except those containing Zr. The Cr containing alloys exhibited notably higher CTE values, particularly the Al containing alloy exhibited the highest value. Ageing heat treatment at 800 and 1000 °C for 96 h and subsequent microstructural analysis revealed significant precipitation of secondary phases in MoNbTiZr, MoNbTiZrV and MoNbTiCrAl. In conclusion, a substantial increase in hardness was observed in MoNbTiZr and MoNbTiCrAl due to secondary phase precipitation, while the other alloys maintained hardness values comparable to their as-cast and homogenized states.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Effect of Si impurities on microstructure and tensile properties of a cast Al-Mg-Fe alloy

Al-Mg alloys are attractive for structural castings owing to their superior strength and ductility in the as-cast state. However, given the tight tolerance for impurities, Al-Mg alloys produced from secondary sources still face multiple challenges. Here, we report the effect of increased Si impurity (0.05–1.6 wt%), which is commonly found in secondary Al sources, on microstructure and tensile properties of a cast Al-4.3Mg-1.6Fe (wt%) alloy, commercially referred to as Castaduct-42 alloy. Microstructural characterization revealed that Si addition increased the volume fraction, size, and aspect ratio of primary Al13Fe4 intermetallic particles as well as the volume fraction of other binary and ternary eutectic phases. Tensile testing results demonstrated that increasing Si impurities from 0.05 to 1.6 wt% reduced ductility from 14.3 ± 1.4 % to 2.2 ± 1.0 %. A particle cracking damage accumulation model coupled with failure analysis indicated primary Al13Fe4 intermetallic particles to be the major contributing factor to the deterioration in ductility with increasing Si content. Additionally, the stabilizing effect of Si on primary Al 13 Fe 4 was inconsistent with the CALPHAD calculation results based on existing CALPHAD databases which predict a slightly decreasing primary Al13Fe4 phase fraction with increasing Si concentration. This work provides new insights into the phase stability and mechanical behavior of the lesser studied Al-Mg-Fe-Si alloy system that will contribute to the development of sustainable cast Al-Mg based alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Design and Development of Novel Equiatomic Refractory Multi Principal elemental Alloys Based on MoNbTi System for Use in Irradiation Environments

Multi Principal Elemental Alloys (MPEA) have emerged as promising materials for next-generation nuclear reactors due to their exceptional irradiation resistance. Eight equiatomic MPEA based on the MoNbTi system, comprising of elements with low thermal neutron absorption cross-sections were explored using a combined approach employing empirical parameter estimations, and CALPHAD simulations by which the phases and elemental segregation observed in all the alloys in the as-cast state were predicted. Solution heat treatment at 1500°C transformed five alloys into single-phase matrix materials, enhancing homogeneity and reducing hardness. The densities of the alloys ranged between 6.47 to 7.68 g/cm3, hardness between 472 and 656 VHN, Young’s modulus between 142 GPa to 169 GPa, shear modulus between 54 GPa and 62 GPa, bulk modulus between 117 GPa to 194 GPa and Poisson’s ratio between 0.3 to 0.35. The in-situ high temperature Xray diffraction results, differential scanning calorimetry and dilatometry results up to 1000°C suggested the high temperature phase stability of the MPEA. Subsequent ageing heat treatment at 800 and 1000 oC for 96 hours revealed significant secondary phase precipitation in MoNbTiZr, MoNbTiZrV, and MoNbTiCrA. Oxidation studies at 800 oC for 24 hours in air revealed superior oxidation resistance and cubic rate law dependence in Cr containing MPEA especially in MoNbTiCrAl, while severe mass gain resulting in total disintegration and exfoliation in MoNbTiZr and MoNbTiZrV. This comprehensive study underscores the potential of novel MPEA as promising materials for advanced nuclear reactor applications, shedding light on their microstructural control, mechanical properties, thermal stability, and oxidation resistance.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Wrought Aluminum-Cerium Alloys by Shear Assisted Processing and Extrusion

Al-Ce alloys have attracted recent interest because of their high thermal stability due to the very low solubility of Ce in the Al matrix. The Al 11 Ce 3 eutectic phase gives excellent strain hardening behavior and moderate high-temperature strength in the as-cast state. However, its strengthening effect is limited by its coarse as-cast structure. Therefore, alternative manufacturing methods such as additive manufacturing or equal channel angular pressing have been applied to refine the Al 11 Ce 3 phase to good effect. However, these techniques are both expensive and time-consuming. Therefore, this study aims to use Shear Assisted Processing and Extrusion (ShAPE), an emerging solid phase processing technique that is more easily scalable than the previously mentioned methods. ShAPE can produce useful cross-sections of an Al-8Ce-4Mg alloy while refining the Al 11 Ce 3 phase to produce a higher strength material. It was found that a low temperature ShAPE process can improve the room temperature yield strength by ~60% compared to a binary Al-4Mg alloy. Additionally, the high-temperature yield strength of the Al-Ce alloys increased by 20%, with a simultaneous 15% improvement in ductility compared to the binary Al-Mg alloy. These results highlight the potential for ShAPE as a processing technique for Al-Ce alloys.

36 MATERIALS SCIENCE↗