Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Ammonia removal”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Design, fabrication and testing of a dual catalyst ammonia removal system for a urine VCD unit

A three-man capacity catalytic system for the recovery of water from urine was designed, constructed, and tested, it was designed to operate with feed streams containing high concentrations of urine vapor and only 5 to 7% of oxygen for the oxidation of ammonia and volatile organic vapor.It can operate either in a flow-through or a recycle mode and is capable of accepting the urine vapor produced by a vapor compression distillation evaporator. Testing consisted of short preliminary and optimization test, an endurance test of 74 hours continuous operation, and recycle tests using both air and oxygen. The system was designed for a urine processing rate of 0.86 liters/hr; however, it was tested at rates up to 1.2 liter/hr. Untreated urine evaporated by an electrically heated evaporator was used. The quality of the recovered water meets the U.S. Drinking Water Standards, with the exception of a low pH. Accumulation of solids in the urine sludge is reduced to approximately 65% of the anticipated value.

Budinikas, P.↗
NASA NTRS1976

Study of removal of ammonia from urine vapor by dual catalyst

The feasibility of ammonia removal from urine vapor by a low temperature dual-catalyst system was investigated. The process is based on the initial catalytic oxidation of ammonia present in urine vapor to nitrogen and nitrous oxide, followed by a catalytic decomposition of the nitrous oxide formed into its elements. The most active catalysts for the oxidation of ammonia and for the decomposition of N2O, identified in screening tests, were then combined into dual catalyst systems and tested to establish their overall efficiencies for the removal of ammonia from artificial gas mixtures. Dual catalyst systems capable of ammonia removal from the artificial gas mixtures were then tested with the actual urine vapor produced by boiling untreated urine. A suitable dual catalyst bed arrangement was found that achieved the removal of ammonia and organic carbon, and recovered water of good quality from urine vapor.

Budininkas, P.↗
NASA NTRS1977

Removal of ammonia from urine vapor by a dual-catalyst system

The feasibility of removing ammonia from urine vapor by a low-temperature dual-catalyst system has been demonstrated. The process is based on the catalytic oxidation of ammonia to a mixture of nitrogen, nitrous oxide, and water, followed by a catalytic decomposition of the nitrous oxide into its elements. Potential ammonia oxidation and nitrous oxide decomposition catalysts were first screened with artificial gas mixtures, then tested with the actual urine vapor produced by boiling untreated urine. A suitable dual-catalyst bed arrangement was found that achieved the removal of ammonia and also organic carbon, and recovered water of good quality from urine vapor.

Budininkas, P.↗
NASA NTRS1973

The catalytic removal of ammonia and nitrogen oxides from spacecabin atmospheres

Investigations were made on methods for the removal of ammonia and to a lesser extent nitrogen oxides in low concentrations from air. The catalytic oxidation of ammonia was studied over a temperature range of 250 F to 600 F and a concentration range 20 ppm to 500 ppm. Of the catalysts studied, 0.5 percent ruthenium supported on alumina was found to be superior. This material is active at temperatures as low as 250 F and was found to produce much less nitrous oxide than the other two active catalysts, platinum on alumina and Hopcalite. A quantitative design model was developed which will permit the performance of an oxidizer to be calculated. The ruthenium was found to be relatively insensitive to low concentrations of water and to oxygen concentration between 21 percent and 100 percent. Hydrogen sulfide was found to be a poison when injected in relatively large quantities. The adsorption of ammonia by copper sulfate treated silica gel was investigated at temperatures of 72 F and 100 F. A quantitative model was developed for predicting adsorption bed behavior.

Gully, A. J.↗
NASA NTRS1972

Design and development of a prototype wet oxidation system for the reclamation of water and the disposition of waste residues onboard space vehicles

Laboratory investigations to define optimum process conditions for oxidation of fecal/urine slurries were conducted in a one-liter batch reactor. The results of these tests formed the basis for the design, fabrication, and testing of an initial prototype system, including a 100-hour design verification test. Areas of further development were identified during this test. Development of a high pressure slurry pump, materials corrosion studies, oxygen supply trade studies, comparison of salt removal water recovery devices, ammonia removal investigation, development of a solids grinder, reactor design studies and bearing life tests, and development of shutoff valves and a back pressure regulator were undertaken. The development work has progressed to the point where a prototype system suitable for manned chamber testing can be fabricated and tested with a high degree of confidence of success.

Jagow, R. B.↗
NASA NTRS1971

Antipollution system to remove nitrogen dioxide gas

Gas phase reaction system using anhydrous ammonia removes nitrogen dioxide. System consists of ammonia injection and mixing section, reaction section /reactor/, and scrubber section. All sections are contained in system ducting.

Metzler, A. J.↗
DOE OSTI2025

Development of an Energy-Efficient and High-Productivity Ammonia Recovery and Removal Process Using Resin-Wafer Electrodeionization

As efforts to develop various energy resources, ammonia energy is emerging as a promising carbon-free fuel alternative. Recovering high-concentration ammonia and ammonium from wastewater potentially offers significant environmental and economic benefits. However, research on recovery technologies for industries such as semiconductors remains limited. This study develops an efficient, energy-saving ammonia recovery technology using Resin Wafer Electrodeionization (RW-EDI), specifically for the semiconductor industry. RW-EDI shows promise for recovering ammonia from high-concentration wastewater. By optimizing parameters, such as voltage and initial concentration, a balance between productivity and energy consumption is achieved. Results indicate that ammonium and fluoride ion transport kinetics are similar, with minimal competition and selectivity values between 0.95 and 1.08. As the initial ammonia/ammonium concentration increases from 500 to 8000 ppm, reaction rate constants and the overall mass transfer coefficient decrease. Increasing the voltage can enhance mass transfer and eliminate barriers. Ion transport primarily occurs in the RW solid phase, accounting for 93.89% of the total current. Additionally, RW-EDI shows superior specific energy consumption within a concentration range of 500 ppm to 8000 ppm, outperforming technologies like electrodialysis by reducing specific energy consumption from 8−15 kWh/kg-NH 4 + to 1.2−2.5 kWh/kg-NH 4 + . This study highlights RW-EDI’s potential for ammonia recovery, providing valuable insights for future applications in wastewater treatment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1978

Four-man rated dual catalyst system for the recovery of water from urine

The catalytic system was integrated with a 4-man rated urine wick evaporator. During operation, urine vapor produced by the wick-evaporator was treated in the catalytic system to remove ammonia and volatile hydrocarbons, and water was recovered by condensation in a water cooled condenser. The system operated completely automatically and required no manual adjustments, except periodic supply of urine and removal of the recovered water. Although the system was designed for treating 0.325 kg urine per hour, this rate could be achieved only with a fresh wick, then gradually decreased as the wick became saturated with urine solids. The average urine treatment rates achieved during each of the three endurance tests were 0.137, 0.217, and 0.235 kg/hr. The quality of the recovered water meets drinking water standards, with the exception of a generally low pH.

Budininkas, P.↗
DOE OSTI2025

Cu-induced robust Ni 2+ /Ni 3+ transition on amorphous Ni hydroxide-based electrocatalysts for advancing electrochemical ammonia oxidation and hydrogen evolution

The electrochemical ammonia oxidation reaction (AOR) is a promising anodic reaction for hydrogen production, offering a lower theoretical potential compared to oxygen evolution reaction. Despite this thermodynamic advantage, AOR suffers from sluggish multi-electron transfer reaction kinetics and the regeneration of catalytically active Ni 3+ species, which limits both activity and durability. In this study, amorphous NiCu bimetallic catalysts were prepared via facile precipitating metal nitrate deposition (PMND) method. The addition of Cu induces a robust Ni 2+ /Ni 3+ transition, stabilizing catalytically active Ni 3+ species and modulating the electronic structure of Ni. It alters the oxidation and desorption behavior of nitrogen-containing intermediates and facilitating their conversions to NO x species, resulting in fast active site regeneration. Furthermore, amorphous structure provides abundant dangling bonds, which enhances the intrinsic reactivity and accessibility of active sites rather than increasing the number of active sites. As a result, these effects accelerate the overall reaction kinetics. The optimized NiCu 5:1 catalyst achieved an ammonia removal efficiency of ∼100 % and a hydrogen production rate of 2.45 mmol/(h∙cm 2 ) at 1.6 V RHE .

Amorphous electrocatalyst↗
NASA NTRS1979

Design and fabrication of a four-man capacity urine wick evaporator system

The integrated system was tested to determine the performance characteristics and limitations of the dual catalyst concept. The primary objective of the dual catalyst concept is to remove ammonia and other noxious substances in the gas phase and thereby eliminate the need for and current practice of chemically or electrochemically pretreating urine prior to distillation.

Source record↗
DOE OSTI2025

Molecular Insights into Novel Struvite–Hydrogel Composites for Simultaneous Ammonia and Phosphate Removal

Struvite (NH 4 MgPO 4 ·6H 2 O) mineralization is an effective technique for removing ammonium and phosphate species from wastewater. However, its wider use faces obstacles because of the copresence of various pollutants in wastewater and the additional requirement for magnesium to achieve proper supersaturation conditions. To address these challenges, this study developed novel mineral–hydrogel composites that can remove ammonium and phosphate simultaneously via heterogeneous struvite and calcium phosphate (CaP) mineralization in hydrogel matrices. The composites include in situ formed struvite and CaP mineral seeds, decreasing the nucleation energy barrier of struvite and CaP formation and promoting their heterogeneous nucleation kinetics even under undersaturation conditions in bulk solution. The dual struvite and CaP seeded composites can simultaneously reduce the ammonium and total phosphate concentrations up to 60% (26.3 mg of N/g) and 91% (9.54 mg of P/g), respectively. Furthermore, the average particle sizes in composites were increased from 6.12 to 14.8 nm after wastewater treatment. Moreover, various ions commonly existing in wastewater did not significantly interfere with the removal of ammonium and phosphate. Thus, these new mineral–hydrogel composites can provide an innovative way to lower nutrient levels before discharge to streams. Moreover, encapsulating ammonium and phosphate in mineral-hydrogel composites enables their upcycling in agricultural or biorefinery applications.

Cations↗
DOE OSTI2025

Real-Time Detection of Hydrogen and Ammonia Isotopologues for Impurity Removal and Recovery of Tritium

To accommodate gas measurements for impurity removal and recovery of tritium, a silver-coated optical or waveguide is employed for collecting Raman scattered signals to determine relative hydrogen and ammonia isotopologue populations in real time. The data and results presented here demonstrate an analytical methodology for the analysis of four ammonia and three hydrogen isotopologues in a hydrogen–deuterium exchange reaction by gas phase Raman spectroscopy. Standard chemometric modeling techniques effectively unravel the signatures of the isotopologues involved observed here; however, a sophisticated quantum chemical approach supports the spectral assignments. An interpretation of the data presented here can emphasize the practicality and reliability of the gaseous monitoring system in complex chemical environments for the hydrogen fuel economy as well as the more distant energy source from a facility that handles tritium. There are still considerable concerns about the measurement of tritium in isotope separation and radiological impurities from gas processing. A common impurity in gas processing is ammonia, which can form readily in the presence of nitrogen and tritium. Substituted ammonia (NQ 3 ), where Q = H, D, or T, is traditionally removed through getters or diffusers along with other non-hydrogen contaminants. A preferable analytical approach is noninvasive and can be deployed for real-time process evaluation in radiological environments.

Ammonia↗
DOE OSTI2025

Develop an efficient and cost-effective novel anaerobic digestion system producing high purity of methane from diverse waste biomass

This project focuses on developing an advanced, intensified anaerobic digestion system aimed at transforming the treatment and conversion of organic wastes into valuable products, specifically renewable natural gas. The motivation for this research stems from the limitations of conventional anaerobic digestion technologies, which often face challenges such as long retention times, high operational costs, and incomplete organic material degradation. The new technology called Intensified Versatile Anaerobic Digestion (IVAD), is developed to address these challenges by incorporating innovative reactors and processes that enhance the overall efficiency and output of anaerobic digestion. The significance of this project lies in its potential to revolutionize waste management practices and waste biomass utilization. The IVAD system integrates a hyperthermophilic anaerobic acidification reactor, a hydrothermal treatment (HTT) unit, and both thermophilic and mesophilic methanogenic reactors. This combination enables a higher rate of organic breakdown and energy recovery, resulting in faster processing times, reduced reactor sizes, and lower operational costs compared to traditional systems. Key data include an increase in methane productivity to 1.18 m 3 /m 3 /day, a significant improvement compared to the baseline technology’s 0.64 m 3 /m 3 /day. Additionally, the IVAD system achieves a 45% reduction in levelized cost of energy (LCOE), down to $\$$10.04/MMBTU, and an energy return on investment (EROI) of 3.19, representing an 87% increase over baseline levels. Technical and economic analyses highlight that the IVAD system significantly reduces hydraulic retention time (HRT) and solid retention time (SRT). The HRT for the HTT reactor can be reduced from 1 hour to 0.5 hours, while decoupling SRT from HRT in the anaerobic acidification reactor (AAR) allows for further reductions. These design optimizations lead to smaller reactor volumes, cutting down equipment and construction costs. Despite these advancements, energy consumption remains comparable to conventional methods due to a novel heat recovery strategy, enhancing overall process productivity. The system also achieves in-situ CO 2 removal and ammonia stripping features, resulting in biogas with a methane purity level of 75%, and produces high-quality nitrogen fertilizer as an additional by-product. Public benefits of the IVAD system are substantial, contributing to sustainable waste management and renewable energy production. By providing a scalable solution that can be adopted by dairy farms and similar agricultural operations, the IVAD system helps reduce waste, produce renewable natural gas (RNG) suitable for transportation fuel, and generate fertilizer, supporting a circular economy. This project plays a role in achieving broader environmental objectives by mitigating greenhouse gas emissions and promoting energy independence. Additionally, it offers a pathway for farmers to lower operational costs while adopting practices that are both environmentally sustainable and economically advantageous.

03 NATURAL GAS↗
NASA NTRS1980

Development of a nitrogen generation system

An eight-stage nitrogen generation module was developed. The design integrated a hydrazine catalytic dissociator, three ammonia dissociation stages and four palladium/silver hydrogen separator stages. Alternating ammonia dissociation and hydrogen separation stages are used to remove hydrogen and ammonia formed in the dissociation of hydrazine which results in negligible ammonia and hydrogen concentrations in the product nitrogen stream. An engineering breadboard nitrogen supply subsystem was also developed. It was developed as an integratable subsystem for a central spacecraft air revitalization system. The subsystem consists of the hydrazine storage and feed mechanism, the nitrogen generation module, the peripheral mechanical and electrical components required to control and monitor subsystem performance, and the instrumentation required to interface with other subsystems of an air revitalization system. The breadboard nitrogen supply subsystem was integrated and tested with a one-person capacity experimental air revitalization system. The integration, checkout and testing was successfully accomplished.

Heppner, D. B.↗
NASA NTRS1970

Control of Nitrogen Dioxide in Stack Emission by Reaction with Ammonia

The development of an acid base gas-phase reaction system which utilizes anhydrous ammonia as the reactant to remove nitrogen dioxide from hydrazine-nitrogen tetroxide rocket combustion exhaust is reported. This reaction reduced NO2 levels in exhaust emissions so that the resulting stack emission is completely white instead of the earlier observed typical reddish-brown coloration. Preliminary analyses indicate the importance of reaction time and ammonia concentration on removal efficiency and elimination of the health hazard to individuals with respiratory problems.

Metzler, A. J.↗
DOE OSTI2026

Intrinsically Conductive {pi}‑d Conjugated Layers with Co–N4 Active Sites for Efficient Nitrate Electrocatalysis and Zinc-Nitrate Batteries

Electrochemical synthesis of ammonia from nitrate has been extensively investigated as a potential alternative to the energy-intensive Haber-Bosch process. This approach not only operates under ambient conditions but also simultaneously removes nitrate contaminants while producing ammonia as a value-added product. However, the ongoing quest lies in designing an efficient electrocatalyst that achieves a high ammonia yield rate, high selectivity, and long-term stability. Herein, we report the outstanding performance of a Co–N4 coordinated π-d layered Co3(HITP)2 (HITP = 2,3,6,7,10,11-hexaiminotriphenylene) in nitrate electrocatalysis. The unique combination of abundant Co–N4 active sites and superior electrical conductivity enables significant electrocatalytic activity, delivering a maximum ammonia yield rate of 56.8 mg cm–2 h–1 at −0.8 V vs RHE and a Faradaic efficiency of ∼91% at −0.4 V vs RHE. Mechanistic analysis reveals that alkaline conditions accelerate water dissociation to generate adsorbed hydrogen intermediates (H*), which are utilized by Co–N4 sites to drive the stepwise hydrogenation of nitrate to ammonia while suppressing competing hydrogen evolution reaction (HER) pathways. Furthermore, integration of this catalyst into a zinc-nitrate battery resulted in a maximum power density of 5.3 mW cm–2 and an open-circuit potential of ∼1.45 V. These results highlight the potential of π-d conjugated Co–N4 materials as an efficient catalyst for both environmental remediation and energy conversion.

Namvar, shahrirar↗
NASA NTRS1977

Electrolytic pretreatment of urine

Electrolysis has been under evaluation for several years as a process to pretreat urine for ultimate recovery of potable water in manned spacecraft applications. The conclusions that were drawn from this investigation are the following: (1) A platinum alloy containing 10 percent rhodium has been shown to be an effective, corrosion-resistant anode material for the electrolytic pretreatment of urine. Black platinum has been found to be suitable as a cathode material. (2) The mechanism of the reactions occurring during the electrolysis of urine is two-stage: (a) a total Kjeldahl nitrogen and total organic carbon (TOC) removal in the first stage is the result of electrochemical oxidation of urea to CO2, H2O, and ammonia followed by chloride interaction to produce N2 from ammonia, (b) after the urea has been essentially removed and the chloride ions have no more ammonia to interact with, the chloride ions start to oxidize to higher valence states, thus producing perchlorates. (3) Formation of perchlorates can be suppressed by high/low current operation, elevated temperature, and pH adjustment. (4) UV-radiation showed promise in assisting electrolytic TOC removal in beaker tests, but was not substantiated in limited single cell testing. This may have been due to non-optimum configurations of the single cell test rig and the light source.

Source record↗
NASA NTRS1973

Techniques for lithium removal from 1040 C aged tantalum alloy, T-111

The liquid ammonia and vacuum distillation techniques were found to be satisfactory for removing lithium from 1040 C aged T-111 (tantalum - 8-percent tungsten- 2-percent hafnium). Results of ductility tests and chemical analysis show that these two methods are adequate for removing lithium without embrittlement or contamination of the T-111. Moist air exposure of T-111 with traces of lithium on the surface produced mixed results. Some specimens were ductile; others were brittle. Brittle T-111 had an increased hydrogen content. Water removal of lithium from T-111 caused brittleness and an increased hydrogen concentration.

Gahn, R. F.↗