Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ALUMINIUM 42”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

First Observation Of New Neutron-Rich Magnesium, Aluminum, and Silicon Isotopes

The investigation of the limits of nuclear existence is fundamental to the understanding of nuclear forces and structure. The limits of binding for very neutron-rich nuclei and the location of the neutron dripline are established experimentally only for the lightest elements. We report on the discovery of the new neutron-rich isotopes {sup 40}Mg, {sup 42,43}Al, and {sup 44}Si. These rare isotopes were produced at the National Superconducting Cyclotron Laboratory by fragmentation of a 141 MeV/u {sup 48}Ca beam on a tungsten target. The combination of the A1900 fragment separator together with the analysis beam line of the S800 spectrograph provided a two-stage fragment separation with exceptional selectivity. The observation of the odd-odd nucleus {sup 42}Al, which was predicted to be unbound by FRDM [1] and HFB-8 [2] models, is the first indication that the neutron drip line may be located significantly further towards heavier isotopes in this mass region than it is currently believed.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Nuclear Data Sheets for A = 42

The experimental data are evaluated for known nuclides of mass number A = 42 (Al, Si, P, S, Cl, Ar, K, Ca, Sc, Ti, V, Cr). Detailed evaluated level properties and related information are presented, including adopted values of level and γ–ray energies, decay data (energies, intensities and placement of radiations), and other spectroscopic data. This work supersedes earlier full evaluations of A = 42 published by B. Singh, J.A. Cameron – Nucl.Data Sheets 92, 1 (2001) and P.M. Endt – Nucl. Phys. A521, 1 (1990); Errata and Addenda Nucl. Phys. A529, 763 (1991); Errata Nucl. Phys. A564, 609 (1993) (also P.M. Endt – Nucl. Phys. A633, 1 (1998) update). No excited states are known in {sup 42}Al, {sup 42}P, {sup 42}V and {sup 42}Cr, and structure information for {sup 42}Si and {sup 42}S is quite limited. There are no decay schemes available for the decay of {sup 42}Al, {sup 42}Si, {sup 42}P, {sup 42}V and {sup 42}Cr, while the decay schemes of {sup 42}Cl and {sup 42}Ti are incomplete in view of scarcity of data, and large gap between their Q–values and the highest energy levels populated in corresponding daughter nuclei. Structures of {sup 42}Ca, {sup 42}K, {sup 42}Sc and {sup 42}Ar nuclides remain the most extensively studied via many different nuclear reactions and decays.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Discovery of the Most Neutron-rich Nuclei With 12 <Z<25 and Future Prospects With the FRIB project

The production of the most neutron-rich nuclei by the fragmentation of {sup 48}Ca and {sup 76}Ge beams at Michigan State are presented. The cross sections were measured for a large range of nuclei including fifteen new isotopes that are the most neutron-rich nuclides of magnesium, aluminum, silicon, and the elements from chlorine to manganese. The observation of {sup 42}Al was itself surprising. The cross sections of several new nuclei are enhanced relative to a simple thermal evaporation framework, previously shown to describe similar production cross sections, indicates that precursor excited nuclei in the region around {sup 62}Ti that decay to the observed nuclei may be more stable than predicted by current mass models. This may be evidence for a new island of inversion similar to that centered on {sup 31}Na. It was recently announced that Michigan State will be the site of the next generation radioactive beam facility, FRIB, for the United States. A brief overview of the proposed facility are presented.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

A Novel RFID-Based Strain Sensor for Wireless Structural Health Monitoring

Conventional tools for deformation measurement are widely used for structural health monitoring—i.e. strain gauges and fiber optic sensors—due to their relative low cost and efficiency. However, these techniques still present some drawbacks particularly in limited access locations, since their usage requires some sort of cabling or battery-driven electronics. Thus, in a few situations there may be room for new technologies for deformation monitoring of structures. One of the options are passive radio frequency identification (RFID)-based sensors. In synthesis, like conventional methods, these sensors are attached to the surface a test-piece, but are then remotely interrogated and powered by a transmitter. The solidarity of the sensor to the underlying material means that the detected signal is modified in a way that can be correlated to sample strain in a given direction. This paper encompasses the project of a wireless deformation sensor based on an inverted-F antenna focusing on its miniaturization and performance optimization. For this purpose, such an antenna was designed with the help of finite element modelling tools for operation on a 2.0 mm-thick aluminium sheet, and then experimentally validated through static loading tests. Finally, even though sensors of this kind are still in early developments, results show that RFID sensors represents a promising method for remote deformation assessment in components.

42 ENGINEERING↗

Characterization of Heterogeneous Response of Al Bicrystal Subject to Micro Scale Laser Shock Peening

This letter shows the ability to perform characterization of the strain field in an aluminium bicrystal subject to plane strain condition induced by micro scale laser shock peening. Intensity contrast method, previously used in topographic measurements of strain fields in thin films is employed here. Our results show that this method is applicable for measurements of the plastically deformed bulk materials. Moreover, heterogeneous response of the grain boundary is observed as periodic nature of deformation.

36 MATERIALS SCIENCE↗

A Study on the Use of XCT and FEA to Predict the Elastic Behavior of Additively Manufactured Parts of Cylindrical Geometry

Defining general criteria for the acceptability of defects within industrial components is often complicated, since the specific load conditions and the criticality of the given application should be considered individually. In order to minimize the risk of failure, high safety factors are commonly adopted during quality control. However this practice is likely to cause the rejection of components whose defects would be instead acceptable if a more sound knowledge of the component behaviour were achieved. Parts produced by additive manufacturing (AM) may suffer from various defects, including micro- or macro-holes, delamination and microstructural discontinuities. Such processes, which are specially suitable for one-off components, require robust and reliable inspection before a part is accepted or rejected, since the refusal of even a single part at the end of the production process represents a significant loss. For this reason, it would be very useful to simulate in a reliable way whether a certain defect is truly detrimental to the proper working of the part during operation or whether the component can still be used, despite the presence of a defect. To this purpose, the paper highlights the benefits of a synergistic interaction between Industrial X-ray computed tomography (XCT) and finite element analysis (FEA). Internal defects of additively manufactured parts can be identified in a non-destructive way by means of XCT. Then FEA can be performed on the XCT-based virtual model of the real component, rather than on the ideal CAD geometry. A proof of concept of this approach is proposed here for a reference construct produced in an Aluminium alloy by AM. Numerical results of the proposed combined XCT–FEA procedure are contrasted with experimental data from tensile tests. The findings sustain the reliability of the method and allow to assess its full provisional accuracy for parts of cylindrical geometry designed to operate in the elastic field. The paper moves a step beyond the present application limits of tomography as it is currently employed for AM parts and it evidences instead the possibility of extending the usage of tomography to acceptance testing and prediction of operative behaviour.

42 ENGINEERING↗

Parametric Optimization of Erosive Wear Response of TiAlN-Coated Aluminium Alloy Using Taguchi Method

In this research work, high-velocity oxy-fuel thermal spraying is used to develop TiAlN coatings on AA1050 and AA5083 aluminium alloy substrates. Slurry wear behavior of coatings is evaluated using jet-type test rig. Surface studies were carried out to investigate the potential erosion mechanism. The influence of key parameters identified using the Taguchi analysis is also corroborated with a wear model. The potential mechanism identified by wear model is in excellent convergence with that observed experimentally. Mixed ploughing and cutting, formation of platelets, abrasion grooves and cracks are witnessed as primary mechanisms causing loss of coating. Results indicate that impact velocity is recognized as a highly contributing parameter with contribution ratio of 79.24 and 83.75% followed by impingement angle with contribution ratio of 15.81 and 11.58% for AA1050 and AA5083, respectively. The important sequences of the control parameters are recognized to be impact velocity > impingement angle > erodent feed rate > erodent size for AA1050 and impact velocity > impingement angle > erodent size > erodent feed rate for AA5083. The best possible combination of control parameters for AA1050 and AA5083 to achieve minimal wear rate with respect to impact velocity, erodent size, impingement angle and erodent feed rate is 30 m/s, 225 µm, 30°, 160 g/min and 25 m/s, 150 µm, 30°, 160 g/min, respectively.

36 MATERIALS SCIENCE↗

Development of an MKIDs-Based THz Superconducting Imaging Array (TeSIA) at 0.85 THz

Dome A, the highest point of the cold and dry Antarctic ice sheet, offers the best access to atmospheric windows at THz/FIR wavelengths on Earth. China is planning to build a 5-m THz telescope (DATE5) there. To achieve its scientific goals associated with large sky surveys, we are developing a THz superconducting imaging array (TeSIA) at 0.85 THz (350-μm window) with a pixel number of 32 × 32 and targeting background-limited sensitivity. In this paper, detailed system design and performance of the TeSIA based on aluminum MKIDs are presented.

42 ENGINEERING↗

Dual-Color Antenna-Coupled LEKID for Next-Generation Multi-chroic CMB Focal Planes

We present an antenna-coupled Kinetic Inductance Detector for millimeter wave astronomy. Next-generation telescopes for observing the cosmic microwave background are demanding in terms of number of detectors and focal plane area filling efficiency. Moreover, foreground reduction in B-Mode polarimetry requires sky observation with multiple frequency bands. In this context, KIDs are a promising technology because of their large multiplexing rate, while antenna coupling can provide multi-band and dual-polarization solutions in compact design. We have developed polarization-sensitive dual-band pixel at 140 and 160 GHz with a bandwidth of almost 8% for each sub-band. The design involves a microstrip-excited slot antenna and two open-stub band-pass filters to direct the signal toward two resonators. These are lumped elements capacitively coupled to the antenna and include an aluminum strip as absorber. The architecture proposed is particularly simple to fabricate, via-less and only involves two metallization levels. The transition does not require any dielectric deposition above the resonator, thus preventing limitations from any source of noise due to a non-monocrystalline substrate. Furthermore, the same coupling technique can be applied to many types of microstrip-excited antennas, which allow to accommodate band-pass filters.

42 ENGINEERING↗

Experimental Measurement of Scatter to Primary Ratio by Localized Primary Modulation in Industrial Computed Radiography

The scatter-to-primary ratio (SPR), can serve as an important parameter for performing the scatter correction procedures or build up factor determination in radiography projections. In this work an experimental technique is presented based on localized primary modulation for direct SPR measurement. As illustrative examples, the SPR is measured for steel and aluminum step wedges to demonstrate the applicability of the presented technique in computed radiography. As a required parameter, the effective transmission factor of the modulator is measured using primary beam stopping concept over a calibration block. This technique has significant advantages such as a straight forward theory, simplified applicability in industrial site conditions, beam hardening consideration as well as automation possibility. The technique works by a single image acquisition, without image data loss in the interested area.

42 ENGINEERING↗

Broadband Calibration of Acoustic Emission and Ultrasonic Sensors from Generalized Ray Theory and Finite Element Models

This paper describes a calibration method for acoustic emission and ultrasonic sensors that is effective from 1 kHz to 1 MHz. The method combines generalized ray theory and finite element analysis to model wave propagation at higher and lower frequencies, respectively. A ball impact is used as a calibration source, a thick aluminum plate is used as the test block, and hot glue is used as the couplant. We demonstrate this method on five commercial piezoelectric sensors: Physical Acoustics (PAC) R15a, PAC WSa, Panametrics V101, Panametrics V103, and Valpey-Fisher Pinducer. Our calibration results show that reflections and other wave phases can be more clearly identified with the less-resonant Panametrics sensors. The PAC sensors have the greatest sensitivity and are able to detect surface normal displacements at least down to 1 pm amplitude in the 100s of kHz frequency band. Aperture effect is minimized by the small size of the Pinducer. Our method focuses on the amplitude response of the sensors (phase is ignored) and extends the calibration to a frequency band that is lower than typical analyses. Low frequency information is useful for determining the seismic moment of a seismic source (analogous to the magnitude of an earthquake) and can increase the amount of information acquired in a single recording.

42 ENGINEERING↗

Numerical Simulation of Multiphase Magnetohydrodynamic Flow and Deformation of Electrolyte–Metal Interface in Aluminum Electrolysis Cells

A computational fluid dynamics based multiphase magnetohydrodynamic (MHD) flow model for simulating the melt flow and bath–metal interface deformation in realistic aluminum reduction cells is presented. The model accounts for the complex physics of the MHD problem in aluminum reduction cells by coupling two immiscible fluids, electromagnetic field, Lorentz force, flow turbulence, and complex cell geometry with large length scale. Especially, the deformation of bath–metal interface is tracked directly in the simulation, and the condition of constant anode–cathode distance (ACD) is maintained by moving anode bottom dynamically with the deforming bath–metal interface. The metal pad deformation and melt flow predicted by the current model are compared to the predictions using a simplified model where the bath–metal interface is assumed flat. The effects of the induced electric current due to fluid flow and the magnetic field due to the interior cell current on the metal pad deformation and melt flow are investigated. The presented model extends the conventional simplified box model by including detailed cell geometry such as the ledge profile and all channels (side, central, and cross-channels). The simulations show the model sensitivity to different side ledge profiles and the cross-channel width by comparing the predicted melt flow and metal pad heaving. In addition, the model dependencies upon the reduction cell operation conditions such as ACD, current distribution on cathode surface and open/closed channel top, are discussed.

42 ENGINEERING↗

Numerical Investigation of Desulfurization Kinetics in Gas-Stirred Ladles by a Quick Modeling Analysis Approach

A quick modeling analysis approach for predicting the slag-steel reaction and desulfurization kinetics in argon gas-stirred ladles has been developed in this study. The model consists of two uncoupled components: (i) a computational fluid dynamics (CFD) model for predicting the fluid flow and the characteristics of slag-steel interface, and (ii) a multicomponent reaction kinetics model for calculating the desulfurization evolution. The steel-slag interfacial area and mass transfer coefficients predicted by the CFD simulation are used as the processing data for the reaction model. Since the desulfurization predictions are uncoupled from the CFD simulation, the computational time of this uncoupled predictive approach is decreased by at least 100 times for each case study when compared with the CFD-reaction kinetics fully coupled model. The uncoupled modeling approach was validated by comparing the evolution of steel and slag compositions with the experimentally measured data during ladle metallurgical furnace (LMF) processing at Nucor Steel Tuscaloosa, Inc. Then, the validated approach was applied to investigate the effects of the initial steel and slag compositions, as well as different types of additions during the refining process on the desulfurization efficiency. The results revealed that the sulfur distribution ratio and the desulfurization reaction can be promoted by making Al and CaO additions during the refining process. It was also shown that by increasing the initial Al content in liquid steel, both Al oxidation and desulfurization rates rapidly increase. In addition, it was found that the variation of the initial Si content in steel has no significant influence on the desulfurization rate. Lastly, if the initial CaO content in slag is increased or the initial Al{sub 2}O{sub 3} content is decreased in the fluid-slag compositional range, the desulfurization rate can be improved significantly during the LMF process.

36 MATERIALS SCIENCE↗

Thermo-chemical Fluid Flow Simulation in Hot-Dip Galvanizing: The Evaluation of Dross Build-Up Formation

This paper presents a new computational framework to investigate the driving force for the formation of intermetallic dross particles in the zinc bath and dross build-up on the bath hardware. This is a major problem in continuous hot-dip galvanizing lines. The Computational Fluid Dynamics (CFD) model calculates the turbulent thermo-chemical flow conditions within the liquid melt. A detailed modeling of the steel strip–liquid interface enhances this approach, by means of a conjugated heat transfer calculation and a spatially resolved, temperature- and concentration-dependent iron dissolution and aluminum uptake. The heart of the computational framework is a thermodynamic model, which assesses the driving force for the formation or dissolution of dross particles in the bath and dross build-up on stationary and rotating equipment. The simulation results are validated with temperature and species depth profile measurements. The applicability of the CFD model is shown by investigating the locally resolved aluminum uptake and iron dissolution at the steel-strip surface, and the multi-physics conditions in the region near the roll. The novel approach of evaluating the thermodynamic driving force enables the assessment of the formation of dross build-up at the roll surface.

36 MATERIALS SCIENCE↗

A Modeling Approach for Time-Dependent Geometry Applied to Transient Heat Transfer of Aluminum Electrolysis Cells

The thermal balance of aluminum electrolysis cells (AEC) have to be rigorously controlled in order to improve the efficiency and sustainability of this industrial process. A new modeling strategy is developed to consider the displacements of solid bodies and moving boundaries in finite element models. The transient thermal-electric modeling of the AEC demonstrates the effect of an increase in operating voltage on both the anode cover and the side ledge. With higher heat generation, the anode cover deteriorates and the side ledge thickness decreases. Since the anode cover is characterized by irreversible transformations, the top heat dissipation remains higher even when the operating voltage comes back to its typical value. For the first time, the transient temperature and electric fields throughout the anode life are simulated and validated by industrial measurements. The modeling predictions have been validated from instrumented anodes and manual measurements, all performed on operating AEC.

30 DIRECT ENERGY CONVERSION↗

Investigation on Mechanical Properties and Equivalent Model of Aluminum Honeycomb Sandwich Panels

In this study, positive-pressure, bending, and drum peel tests were carried out for aluminum honeycomb sandwich panels made of different materials and with different dimensions. The results of these tests not only precisely revealed the relationships between the mechanical properties of aluminum honeycomb sandwich panels and the material dimensions of the face and core layers, the layout mode of the core layer, and the connecting mode between the face layers and core layers, but also determined the reliable mechanical equivalent model. The test results indicate that when the specimen was subjected to the vertical load, the compression properties of aluminum honeycomb sandwich panels were mainly determined by its core layer, while the face layer mainly relieves the axial stress and restrains the deformation of the core layer. In the flexural test, the face layer is the main part subjected to the load, whereas the core layer shows supporting, stabilizing, and strengthening effects, slowing the deformation of the face layer; flexural-tensile properties can be somewhat affected by the layout type of the core layer. The equivalent plate model, honeycomb plate model, and sandwich panel model were screened based on the experimental results, indicating that the sandwich panel model provided a more accurate description. The sandwich panel model was further modified, ultimately resulting in a more effective equivalent model that can accurately reflect the mechanical properties of the aluminum honeycomb sandwich panels.

36 MATERIALS SCIENCE↗

Experimental Analysis of the Crushing of Honeycomb Cores Under Compression

This paper presents an experimental study of the compressive response of hexagonal honeycomb core from the initial elastic regime to a fully crushed state. To understand the crushing mechanism, aluminum honeycomb core was compressed quasi-statically between rigid platens under displacement control. Honeycomb test specimens made of aluminum alloy with different configurations such as cell size, cell number, core density, and specimen size have been tested. During the crushing, the cells buckle elastically and collapse at a higher stress due to inelastic action, after the cells crush by progressive formation of folds on cell walls. The response densifies when folds consume the whole panel height. The peak load recorded during tests corresponded to the buckling of honeycomb cells. The different specimens showed similar load/displacement curves, and the differences observed were only due to the influence of the core density, number of cells, and specimens size on mechanical behavior of hexagonal honeycomb core which has a very important role in the energy absorption capacity. In addition, this study allowed us to build a database of experimental tests for various configurations and allowed us to know the precise energy absorption capacity.

36 MATERIALS SCIENCE↗

Experimental Investigation and Numerical Study on the Elimination of Porosity in Aluminum Alloy Laser Welding and Laser–GMA Welding

Keyhole-induced porosity can strongly weaken the joint strength during aluminum alloy laser welding. Two factors are proposed to be responsible for the porosity formation: bubble formation caused by the instability of the keyhole and bubble captured by the solidification interface. Based on numerical and experimental results, the porosity is suppressed with preheating, due to the capillary stability of the keyhole and easy escape of bubble. N{sub 2} shielding gas has a minor effect on keyhole stability, but it reduces the porosity number as N{sub 2} bubble can dissolve into the liquid aluminum alloy melt pool quickly. The laser–gas metal arc (laser–GMA) welding process can stabilize the metallic plume and enlarge the weld pool. As a result, few spatters and bubbles are formed, and bubbles are easily escaped, both of which contribute to the suppression of porosity.

36 MATERIALS SCIENCE↗