SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The purpose of the project was to find a lower cost carbon fiber material solution that would lower end use part cost produced with the Impossible Objects’ 3D Composite Based Additive Manufacturing (CBAM) technology. The two strands of the research were to consider lower cost carbon tow material provided by Oak Ridge National Lab (ORNL) and carbon fiber nonwoven veils containing a soluble binder.
The project (Award DE-FE0032146), led by Baker Hughes in collaboration with the University of Wyoming, aims to develop composite PEEK (Polyether-ether-ketone) materials enhanced using coal-derived graphene-based additives suitable for additive manufacturing (3D printing). Coal char (CC), graphene oxide (GO), and reduced graphene oxide (rGO), derived from Powder River Basin (PRB) coal, were successfully integrated into commercial PEEK feedstock. The composite PEEK materials demonstrated tensile and flexural strengths and modulus, Shore hardness, and thermal properties similar to unfilled PEEK. Dielectric strength of 0.5% GO/PEEK is twice that of unfilled PEEK. However, tensile elongation and Izod impact toughness of the composite materials are lower than unfilled PEEK. The 10% CC/PEEK material also shows good recyclability albeit with slightly increased glass transition and cold crystallization temperatures. Filaments of the composite PEEK materials were fabricated using a Filabot system. 3D printing of the composite PEEK initially encountered feeding stoppage caused by the non-uniform diameter of the filament, which was resolved by reducing the nominal diameter from 1.75 to 1.65 mm. The printability of the composite PEEK filaments is limited in geometry and build time, driven by differences in base PEEK feedstock from the commercial PEEK filament at printing conditions. Prototype part printed using the composite filaments shows inconsistent bead width and bead interruption resulting in porosity. Preliminary process and economic evaluation using PRB coal char estimates the cost of GO to be $0.5/lb. Considering the small fraction expected in the composite PEEK, the GO cost is several orders of magnitude lower than the commercial PEEK filament. It is recommended that the printability of composite PEEK filaments to be improved by optimizing the composite PEEK material at the printing conditions and reducing the variations in filament extrusion. Also important is to identify the mechanisms of how coal-derived additives affect the composite PEEK performance and printing characteristics to allow customized material design and processing for target performance.
Direct ink writing (DIW) is an extrusion-based form of 3D-printing that has gained popularity over the last decade. DIW uses thixotropic fluid extrusion to form a particular shape. In order to form stable structures, the rheology of the paste is important to allow for extrusion from the syringe, stability of the growing print, and prevention of unwanted seeping flow during jog moves. In this work, we use wood pulp as a bio-based filler that can provide shear thinning properties to the ink, which produces a stable ink for DIW processing. Additionally, the filler imparts improved mechanical and thermal performance compared to neat resin. The wood pulp provided the shear thinning behavior necessary for DIW printing, and pulp loadings greater than 6 wt%, provided sufficient yield stress so that the composite could self-support during printing. Nanoclay was utilized to further improve ink rheology and appearance to enable larger scale printing. Overall, this work showed successful DIW of an epoxy resin with a sustainable filler improving its stiffness and thermal properties and provides an avenue for further development of bio-based inks for DIW towards various applications.
The proposed project utilizes advanced ceramic-based 3D-printing technology to develop light, low-cost, ultra-compact, high-temperature high-pressure (HTHP) heat exchangers (HX) for the harsh oxidizing environment of aircraft gas-turbine engines. Typical 3D printing technologies (powder bed or lithographic techniques) cannot produce large high-density, monolithic ceramic material with intricate internal features and channels required for high-temperature, high-pressure recuperators. Furthermore, typical 3D printing technologies are not yet economical for large high-density components. A high-density material is required for hermeticity, high-temperature strength, and oxidation, corrosion, and wear resistance. The team has invented an extrusion-based additive manufacturing technology (referred to as robocasting) and developed processing techniques to tailor composition and rheological mix properties for rapid 3D printing of high-density alumina and SiC parts. The goal of the proposed project is to use robocasting technology to demonstrate commercializable high-density 3D-printed ceramic HX modules with high durability and quality, thereby reducing the risk of thermo-mechanical failure under extreme environments. In addition, the proposed project improves the quality of the ceramic 3D-printing process over a large printed area and HTHP operating conditions. Ceramic 3D printing technology also provides a means to create advanced topologies that are unobtainable with conventional manufacturing.
Utilizing additive manufacturing (AM) techniques with shape memory alloys (SMAs) like NiTi shows great promise for fabricating highly flexible and functionally superior 3D metallic structures. Compared to methods relying on powder feedstocks, wire-based additive manufacturing processes provide a viable alternative, addressing challenges such as chemical composition instability, material availability, higher feedstock costs, and limitations on part size while simplifying process development. This study presented a novel approach by thoroughly assessing the printability of Ni-rich Ni55.94Ti (Wt. %) SMA using the wire laser-directed energy deposition (WL-DED) technique, addressing the existing knowledge gap regarding the laser wire-feed metal additive manufacturing of NiTi alloys. For the first time, the impact of processing parameters—specifically laser power (400–1000 W) and transverse speed (300–900 mm/min)—on single-track fabrication using NiTi wires in the WL-DED process was examined. An optimal range of process parameters was determined to achieve high-quality prints with minimal defects, such as wire dripping, stubbing, and overfilling. Building upon these findings, we printed five distinct cubes, demonstrating the feasibility of producing nearly porosity-free specimens. Notably, this study investigated the effect of energy density on the printed part density, impurity pick-up, transformation temperature, and hardness of the manufactured NiTi cubes. The results from the cube study demonstrated that varying energy densities (46.66–70 J/mm3) significantly affected the quality of the deposits. Lower to intermediate energy densities achieved high relative densities (>99%) and favorable phase transformation temperatures. In contrast, higher energy densities led to instability in melt pool shape, increased porosity, and discrepancies in phase transformation temperatures. These findings highlighted the critical role of precise parameter control in achieving functional NiTi parts and offer valuable insights for advancing AM techniques in fabricating larger high-quality NiTi components. Additionally, our research highlighted important considerations for civil engineering applications, particularly in the development of seismic dampers for energy dissipation in structures, offering a promising solution for enhancing structural performance and energy management in critical infrastructure.
Cement production for concrete has been responsible for ~7–8% of global greenhouse gas (GHG) emissions, and nearly equally contribution for steel production processes (EPA, 2020). In order to achieve carbon neutrality by 2050, a novel solution has to be investigated. This project aims to develop fundamental mechanistic understanding and experimental characterization to create a 3D printable biopolymer concrete using plant-based polyurethane as an innovative and sustainable alternative for Portland cement concrete, with significantly low carbon footprint. Future construction will utilize the advances in digital additive manufacturing (3D printing) to produce optimal geometries with a minimum waste of materials. Understanding the polymerization process, factors impacting the composite rheology, and the structural behavior of this biopolymer concrete will enable us to engineer the next generation of concrete structures with low carbon footprint. This project aims to improve the nation’s ability to control Greenhouse Gas emission neutrality for the set goal of 2050 via introducing a structurally viable bio-based polymer concrete.
Nanostructured multi-principal element alloys (MPEAs) have been explored as next-generation engineering materials due to unique mechanical and functional properties which have significant advantages over traditional dilute alloys. However, the practical applications of nanostructured MPEAs are still limited due to the lack of scalable processing approaches to prepare a large quantity of nanostructured MPEAs, as well as lack of an efficient pathway for high-throughput discovery of better functional nanostructured MPEAs within their vast compositional space. Here we tackle these challenges by presenting an integrated approach by combining direct-ink-writing-based additive manufacturing, solid-state sintering, and chemical dealloying to manufacture hierarchically porous MPEAs. The hierarchical structure is comprised of macro- and micro-scale pores introduced via extrusion printing and polymer decomposition during sintering, as well as nanoscale pores formed via chemical dealloying. The macro- and micro-scale pores allow efficient dealloying of a large mass of material as the diffusion length that the corroding medium must penetrate remains at the scale of the ligaments formed after sintering (∼10 μm), despite the large volume of the 3D-printed samples. In addition, this integrated approach enables versatile control of the alloy composition via precisely tuning the ratio of elemental powders in the starting ink, thus offering a pathway for high-throughput discovery of novel functional MPEAs. As a case study, multiscale macro/micro/nanoporous NiFeMn MPEAs with three different compositions were investigated as catalysts to reduce the overpotential of oxygen evolution reaction (OER), where NiFeMn-based electrocatalysts display composition-dependent performance such that the overpotential measured at a current of 0.5 A g −1 for OER increases in the order of Ni 58 Fe 29 Mn 13 ⩽ Ni 64 Fe 26 Mn 10 < Ni 76 Fe 18 Mn 6 . This introduced manufacturing process offers new opportunities for scalable fabrication and rapid screening of nanostructured multi-component complex alloys.
Owing to its low cost and sustainable nature, lignocellulosic biomass has been utilized for reinforcing polymers, but it is crucial to understand the impact of high-ash concentrations in biomass on composite strength and processing. Biomass is not only desirable for biofuel production but could also have a strong market, if high-ash biomass is acceptable, for biocomposites. In this work, natural fibers (switchgrass and corn stover) were used to reinforce polylactic acid (PLA) to produce biocomposites. Natural fibers were pretreated to obtain fibers that contain different percentages of ash. The mechanical properties (such as Young's modulus, tensile strength, failure strain, storage modulus) of corn stover/PLA composites remained largely unaffected by the ash concentration of the biomass fibers, despite the large range of ash contents (2.2–11.9 wt%). Furthermore, the tensile strengths of switchgrass/PLA composites were slightly negatively affected by the ash concentration of the switchgrass fibers (0.7–2.1 wt%). Both the switchgrass/PLA and the corn stover/PLA composites exhibited a high-enough tensile strength (49–57 MPa) and suitable complex viscosity (2.0–7.0 kPa·s at the frequency of 3.2 rad/s). They are expected to be 3D-printable through an extrusion-based additive manufacturing process.
Advanced manufacturing techniques, such as additive manufacturing (AM), that can directly integrate phase change materials (PCMs) have garnered interest in recent years due to their potential for development of highly efficient thermal energy storage architectures. Complex, high surface area geometries embedded with PCMs that are only feasible with AM can improve thermal management with reduced material waste. Our work focuses on developing composite filaments with microencapsulated phase change materials (MEPCM) bound within a single or dual polymer matrix that can be processed through standard filament extruders and additively manufactured using off-the-shelf 3D printers. Polymer powders, rather than polymer pellets, were key to homogenously mixed filaments achieving high MEPCM loadings with no deterioration in thermal energy storage (TES) capability during extrusion. Composite filaments contain upwards of 60 wt% MEPCM and were printed without loss in feature resolution, print speed, or layer adhesion. Storage enthalpies of printed composites range from 100 - 130 kJ/kg, which were within 5% of the theoretical enthalpy based on weight fraction of MEPCM and maintained enthalpies within 1% over 500 thermal cycles. We can reliably manufacture low density, high surface area structures like 15% gyroid infill, along with dense, compact pucks at a 100% concentric infill. Prints were also scalable to a 900 cm3 honeycomb infill heat exchanger model that has an estimated energy storage capacity of 9 Wh.
This report describes the techno-economic potential of using additive manufacturing technologies to design large wind turbine blade structures. After considering all additive technologies, the authors identified large-scale, polymer-based, material extrusion as the three-dimensional (3D) printing technology best suited to meet modern wind turbine blade manufacturing costs, cycle times, and geometric scale. Due to the lower structural performance requirements and the opportunity to reduce resin uptake mass penalties within the blade, the core material within the sandwich composite sections of the wind turbine blade is established as a logical entry point into advanced wind turbine blade manufacturing.
This report provides results from a printability study of laser directed energy deposition (DED)-based additive manufacturing of nuclear-grade stainless steels as well as DED process parameter development for austenitic Alloy 709 (A709) and ferritic/martensitic Grade 91 (G91) and Grade 92 (G92) steels. The printability study includes the use of machine learning and physics-based modeling via commercial software such as FLOW-3D for insights into the impact of the alloy composition, particularly the carbon content, on the printability of stainless steels during the DED process. In the DED process development work, 1 cm 3 alloy blocks were deposited with broad ranges of laser powers, scan speeds, and hatch spacings to optimize the build quality, resulting in densities of more than 99.8% for all three alloys. The microstructure and mechanical properties were characterized using electron microscopy, X-ray diffraction, and Vickers hardness measurements. Further, tensile samples were extracted from DED-fabricated alloys utilizing the optimized process parameters. The present work provides guidance and progress towards the successful deployment of the DED process for the fabrication of structural components of nuclear reactors.
Biomass (e.g., pine sawdust, especially high–ash content pine sawdust) is commonly disposed of as waste. Combining biomass with polymers to make composite feedstocks for 3D printing has been explored as a method to reduce or repurpose the biomass waste. Although not all biocomposite properties are known, the wood-based polylactic acid (PLA) composite has promising qualities for applications in ecological settings. In this work, pine wood–PLA composite feedstock was used to 3D print supplemental roost structures for endangered tree-roosting bats, which often face a paucity of suitable naturally occurring roosts. This material combination was selected because it is estimated to degrade faster than the synthetic material systems that are used widely in supplemental bat roosting structures to aid in the conservation of tree roosting bats. The layered, rough surface created by the 3D printing process serves as a surface that bats can grip while roosting. Computer-aided design (CAD) models were generated based on natural roost structures, and a full-size bat house was successfully additively manufactured using a pellet-fed large-scale 3D printing system. The 3D printed hexagon exhibited a tensile strength of 22–23 MPa and a Young’s modulus of 3202–3218 MPa in the x-direction. It has been demonstrated that the 3D printed bat house can be installed on a tree in a stable fashion. This successful demonstration of a bat roost manufactured using a bioderived composite should promote its use in other fish and wildlife structures and broader industrial applications such as construction and automobiles.
We report that recently, several efforts have emerged that employ additive manufacturing techniques to integrate phase change material (PCM) thermal energy storage into geometrically complex designs for advanced thermal management. In this work, we contribute to this emerging research by reporting on the production of a composite nylon-based filament for fused deposition modeling incorporating encapsulated PCMs for 3D printing heat sink geometries. Microencapsulated PCM (MEPCM) with a 6 degrees C transition temperature was selected as the material for thermal energy storage. This transition temperature was selected due to its suitability to provide thermal energy storage to target air-conditioning applications in buildings. In an attempt to improve the thermal conductivity of the composite, fine boron nitride fillers were added, although the effect on improvement was found to be negligible in the overall composite mixture. The nylon-MEPCM ratio in the filaments was optimized, and filaments containing up to 40 wt% MEPCM were successfully synthesized, which were found optimal for 3D printing complex heat sink and other geometries. Thermal and mechanical properties of the filaments were characterized, including latent heat of fusion, thermal conductivity, phase change temperature, tensile strength, and more. Thermal infrared imaging of heat sink geometries printed using the MEPCM filaments undergoing thermal discharging was also conducted. This work presents the most promising result to date in the open literature for a 3D-printed PCM composite in the combination of size, energy density, and geometric complexity of printed parts.
Direct Ink Writing (DIW) utilizes a wide range of ink formulations to produce desirable 3D-printed structures and properties. Styrene-butadiene rubber (SBR) is an attractive candidate for 3D printing owing to its commercial availability, rheology, excellent mechanical properties, good impact resilience, and chemical stability. The SBR-based sealant was 3D printed in a DIW process, even in an ambient environment. The rheological behavior was assessed and correlated with optimized printing parameters. Important physico-chemical properties of the 3D-printed material were reported showing excellent properties as an elastomer. Finally, this work should expand the potential applications of existing rubber-based materials in additive manufacturing.
Polyethylene (PE) is one of the best shielding materials for primary space radiation due to its high hydrogen content. For effective secondary neutron shielding, boron-rich fillers are incorporated to enhance performance. The semicrystalline nature and high thermal expansion coefficient of PE impede its adoption for in situ additive manufacture in space via the fused deposition modeling (FDM) 3D printing. Here, we developed an optimized PE blend to mitigate the effects of under-extrusion and warpage. Guided by studies on extrusion and warpage, we developed an optimal set of printing parameters for the proposed PE blend. The optimum PE blend─both in its pure form and when doped with fillers─has been tested on different FDM printers. The printed structures exhibit high and uniform density, smooth surfaces, no warpage, and competitive mechanical properties. The FDM-printed plates demonstrate efficient shielding from thermal neutrons, predicted via modeling and confirmed experimentally using extended Q-range small-angle neutron scattering.
The project scope is to investigate the compatibility of various ceramic and metal powder composite feedstock development, implement AI algorithms for in-situ monitoring and parameter optimization of binder jet 3D printing to achieve reliable and robust metal/ceramic and/or ceramic/ceramic composite components, and create a generative design framework for heterogeneous composite structures incorporating metals and ceramic-based materials to achieve specific mechanical properties. Funded is the effort and travel by the faculty advisor at University of California Berkeley in support of the work of their students and the related collaborative research and development effort.
Appearing as one of the key-components of lithium-ion batteries (LIBs), this work specifically focuses on the additive manufacturing (AM) of custom-shape separators, facilitated by the filament material extrusion process, also called fused deposition modeling (FDM). The development and optimization of composite thermoplastic filament feedstocks combining polypropylene and paraffin wax, followed by the 3D printing of the separator membranes is shown. A post-processing step, based on thermal induced phase separation (TIPS), is introduced to promote porosity formation through removal of the paraffin wax sacrificial phase within the 3D printed items. Separators with different polypropylene/paraffin wax ratios are developed and the impact on printability, mechanical strength, porosity, and electrochemical performances, is thoroughly discussed. X-ray micro-computed tomography is employed to assess the geometric fidelity and to detect printing defects in a complex 3D lattice structure. The performance of the 3D printed porous separators is also compared to a commercial separator. This pioneering research establishes a foundation for the creation of porous separators that can adapt to and conform into 3D printed battery architectures with novel form factors, and also creates opportunities for the use of FDM and TIPS for a wide range of applications that employ porous structures beyond the energy storage field.
In order to meet increasing power-dissipation requirements of the electronics industry, compact, low-cost, and lightweight heat exchangers (HXs) are desired. With proper design, materials, and manufacture, polymer composite heat exchangers could meet these requirements. This paper presents a novel crossflow air-to-water, low-cost, and lightweight metal-polymer composite HX. This HX, which is entirely additively manufactured, utilizes a novel cross-media approach that provides direct heat exchange between air and liquid sides by using connecting fins. A robust numerical model was developed, which includes the dimensional effects of additive manufacturing. The study consists of a simplified 3D CFD model based on ellipsoidal-shaped staggered tube banks for the laminar range. It then uses an analytical approach to compute entire HX performance. The model is validated experimentally within 8% for thermal performance, 12% for air-side impedance, and 18% for water-side impedance. Finally, HX is compared with a conventional CPU radiator and performs within 10% of the conventional unit for reasonable flow rates and pressure-drop ranges. Moreover, HX also provides added design and cost advantages over the conventional unit, which makes the HX a potential candidate for electronic cooling applications.