Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “3D”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

A 3D helical filament surrogate model for 3D tokamak equilibria

A novel approach for efficient representation of three-dimensional (3D) tokamak equilibria is investigated, where a set of helical current filaments occupying the plasma region are employed to resolve deviations from the two-dimensional (2D) axi-symmetric state. A discrete set of 3D filaments, located at rational surfaces for a given toroidal mode number n and following the 2D equilibrium field lines (thus forming closed current loops), are found to provide a surrogate model of 3D equilibria with reasonable accuracy. Specifically, application of the filament model to 3D perturbed equilibria, due to the resonant magnetic perturbation (RMP) in DIII-D and MAST-U discharges, reveals that (1) a single helical filament per rational surface is sufficient; (2) 21 such helical filaments are capable of representing the n = 2 3D response field in MAST-U with less than 10% relative error as compared to that computed by a full magnetohydrodynamic code; (3) optimizing currents (both amplitude and phase) flowing in 3D filaments with fixed geometry, the highest accuracy fitting is found to depend on the characteristics of the 3D equilibria such as the coil current phasing of the RMP coils in our case studies. Here, whis filament approach is also applicable for generating surrogate models of other type of 3D tokamak equilibria, including those during the initial phase of the plasma disruption.

MARS-F↗
NASA NTRS1979

A study of the excitation and radiative decay of the 3s-prime 3D-0 and 3d 3D-0 levels of atomic oxygen

The absolute cross-sections for the excitation of the 989 A, 1027 A, 7990 A, 8446 A, 1.1287 micron and 1.3164 micron multiplets of atomic oxygen by electron impact dissociation of O2 are reported. The radiative branching ratios for these transitions are calculated from these results and compared with the NBS compilation of Wiese et al. (1966) and the recent theoretical calculations of Pradhan and Saraph (1977). The cascade models of O(+) radiative recombination and of electron-impact excitation of the O I(3S) state in the terrestrial airglow are discussed in the light of the laboratory measurements, and the effects of the resonant absorption of components of the lambda 989 A and lambda 1027 A multiplets by the Birge-Hopfield band system of N2 are investigated. This process is shown to depend sensitively on the N2 vibrational temperature and to cause characteristic changes in the OI EUV emission spectrum in auroras and in the sunlit F-region at high exospheric temperatures.

Zipf, E. C.↗
DOE OSTI2026

Data for Impact of Vertical and Seasonal Variation in Leaf Traits on Simulating Soybean Canopy Photosynthesis via 1D and 3D Modeling

Accurate modeling of photosynthesis is crucial for predicting crop productivity and quantifying the carbon cycle in agroecosystems. Leaf traits are essential inputs for modeling canopy photosynthesis. Yet, many existing models still use fixed plant functional type (PTF)-based values to parameterize leaf traits under a big-leaf or two-big-leaf assumption, neglecting their vertical profiles and seasonal changes. This simplification may introduce significant uncertainties in estimating gross primary productivity (GPP). In this study, we simulated soybean GPP and tested the effects of vertical and seasonal variation in three key leaf photosynthetic traits: the maximum carboxylation rate at 25 °C (Vcmax25), leaf chlorophyll content (LCC), and leaf mass per area (LMA) in the 1D-SCOPE and 3D-Helios models. Weekly field measurements were conducted during the growing season of 2024 to support the simulation. We designed ten leaf trait parameterization schemes by incorporating different combinations of vertical profiles and seasonal changes, while assuming homogeneous canopy architecture in both models. Our results revealed that Vcmax25 vertical and seasonal variation had the strongest influence on simulated GPP in both 1D and 3D models, while LCC and LMA effects were minimal. Particularly, the scheme with an empirically parameterized Vcmax25 profile achieved comparable performance to the scheme with the measured Vcmax25 profile. Both 1D-SCOPE and 3D-Helios accurately modeled GPP (SCOPE: R2 = 0.87, Bias = 0.55 µmol m⁻² s⁻¹; Helios: R2 = 0.9, Bias = 0.22 µmol m⁻² s⁻¹) under the most complex scheme, and their responses to vertical and seasonal variation in leaf traits were consistent, demonstrating the robustness of our findings. Based on our findings, we propose a scalable framework for parameterizing leaf traits to improve GPP simulations. This study contributes to improving the representation of leaf trait dynamics in canopy-level photosynthesis models, potentially enhancing our ability to predict crop productivity and understand agroecosystem carbon dynamics.

Photosynthesis↗
DOE OSTI2026

Validation Studies of RELAP5-3D for High-Temperature Gas-Cooled Reactor Analysis Using a Refined RELAP5-3D Model of the High Temperature Test Facility

RELAP5-3D has been used extensively for high-temperature gas-cooled reactor (HTGR) analysis, but such analysis lies outside the validation basis for the code. Oregon State University (OSU) and the United States Department of Energy’s (DOE) Advanced Reactor Technologies (ART) – Gas-cooled reactor campaign worked together to design and operate the High Temperature Test Facility (HTTF) at OSU to provide validation data for prismatic HTGR thermal hydraulics analysis. Work using a previous RELAP5-3D model of HTTF demonstrated the ability to reproduce trends in HTTF data but an inability to reproduce the values measured in multiple experiments within the uncertainty. It was hypothesized that a new model with a finer radial nodalization would perform better for HTTF analysis. In this paper, we present the development of that more refined model and analyze HTTF experiments PG-27 and PG-29, a pressurized (PCC) and depressurized conduction cooldown (DCC) transient. Comparing PG-27 results to experimental data shows a better prediction of steady state and transient temperatures; however, a deeper dive reveals that better transient temperature predictions are a result of better initial conditions. The transient temperature rise in the core is comparable between the two models, but the legacy model predicts temperatures in the reflectors better. The new model demonstrates the ability to predict unique temperatures in each sector of the core during PG-29, capturing the azimuthal asymmetry; however, the temperature predictions still differ from measured temperatures. One hypothesis is that differences between the assumed and actual power distribution leads to the underprediction of the individual block temperatures. These results suggest that gaps and uncertainties in the measured boundary conditions for the HTTF tests do not allow to fully validate RELAP5-3D for prismatic HTGR analyses. The authors suspect that some of the differences between predicted and measured temperatures may be a result of uncertainties associated with HTTF itself rather than RELAP5-3D. We demonstrated improved validation for steady-state analysis, but significantly improved transient performance has yet to be recognized.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2026

3D Cloud Aerosol Precipitation Experiment at kennaook Cape Grim (3D-CAPE-k) Field Campaign Report

The objective of this campaign was to complement the U.S. Department of Energy Atmospheric Radiation Measurement (ARM) User Facility’s Cloud And Precipitation Experiment at kennaook (CAPE-k) in northwest Tasmania by deploying scanning, fixed pointing angle, and in situ aerosol, cloud, and precipitation remote-sensing instruments during the last six months of the experiment. These instruments provided a three-dimensional (3D) context to the second ARM Mobile Facility (AMF2) vertically pointing observations collected at the kennaook Cape Grim (KCG) site and captured a portion of the life cycle of the clouds before and after the passage over the AMF2 vertical column. These 3D cloud measurements will be used in the near future to 1) investigate how the vertical profiles of aerosol and cloud properties are representative of the broader area and how these properties evolve during the portion of the cloud life cycle captured by the scanning instruments, 2) quantify how accurate the cloud fraction derived with assumptions from vertically pointing observations are compared with direct 3D cloud fraction measurements, 3) evaluate cloud fraction and liquid water path in the Australian Community Climate and Earth-System Simulator–Convective-scale (ACCESS-C) forecast model, and 4) evaluate aerosol and cloud products from the European Space Agency/Japanese Aerospace Exploration Agency (ESA/JAXA) Earth Cloud Aerosol Radiation Explorer (EarthCARE) mission using the scanning measurements, offering more chances of exact collocation, thereby complementing the statistical approach we are planning to employ with AMF2 observations for that same purpose.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

3D Continuous Forcing Dataset from 3D Constrained Variational Analysis at SGP

The continuous 3D large-scale forcing (VARANAL3D) data set derived from 3D constrained variational analysis (3DCVA) extends the conventional constrained variational analysis method by incorporating multiple sub-columns within the analysis domain. This advancement introduces spatial variability into the large-scale forcing fields, thereby enriching the data set’s applicability. The VARANAL3D data set spans from 2004 to 2018 and covers a region of 5˚×4.5˚ domain around the ARM SGP site. The analysis domain is divided into 10×9 sub-columns with 0.5˚ resolution. The 3D large-scale forcing data provides necessary variables to drive and evaluate single-column models (SCM), cloud-resolving models (CRM) ,and large-eddy simulations (LES), as well as information for testing model sensitivity to spatial variability of the large-scale forcing data, facilitating more rigorous testing and refinement of physical processes in SCM/CRM/LES.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

A competition between 2D and 3D magnetic orderings in novel mixed valent copper frameworks

Low-dimensional hybrid inorganic–organic frameworks exhibit high structural flexibility and allow for the inclusion of various magnetic and optically-active species into their host structures. The emergence of copper-based hybrid structures for various optical applications provides a promising foundation for exploring the integration of magnetic sublattices, paving the way for advancements in magneto-optical coupling and multifunctional materials. Herein, we introduce a novel class of hybrid copper frameworks with covalently-connected alternating magnetic 2D copper(II) formate and non-magnetic copper(I) bromide layers. The anionic framework is stabilized by A + cations to form ACu 5 Br 4 (COOH) 4 (A + = Na + , K + , Rb + , NH 4 + ) semiconductors (bandgaps 2.1–2.2 eV) with optical transitions suitable for optoelectronic applications. Comprehensive magnetometry studies show that ACu 5 Br 4 (COOH) 4 compounds exhibit low-dimensional 2D short-range antiferromagnetic order within the formate layers, characterized by strong exchange coupling (J/k B ∼ −100 K). Upon further temperature reduction, interactions between Cu(II) layers give rise to 3D long-range magnetic order at ∼40 K, despite the large (8.6–8.8 Å) spatial separation of the magnetic Cu(II) formate layers by nonmagnetic Cu(I)–Br bridging layers. This transition is further supported by electron paramagnetic resonance (EPR) spectroscopy. In conclusion, this study expands our understanding of low-dimensional hybrid frameworks and opens new avenues for the design of 2D multifunctional materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Accelerating Discovery of Solid‐State Thin‐Film Metal Dealloying for 3D Nanoarchitecture Materials Design through Laser Thermal Gradient Treatment

Thin‐film solid‐state metal dealloying (thin‐film SSMD) is a promising method for fabricating nanostructures with controlled morphology and efficiency, offering advantages over conventional bulk materials processing methods for integration into practical applications. Although machine learning (ML) has facilitated the design of dealloying systems, the selection of key thermal treatment parameters for nanostructure formation remains largely unknown and dependent on experimental trial and error. To overcome this challenge, a workflow enabling high‐throughput characterization of thermal treatment parameters is demonstrated using a laser‐based thermal treatment to create temperature gradients on single thin‐film samples of Nb‐Al/Sc and Nb‐Al/Cu. This continuous thermal space enables observation of dealloying transitions and the resulting nanostructures of interest. Through synchrotron X‐ray multimodal and high‐throughput characterization, critical transitions and nanostructures can be rapidly captured and subsequently verified using electron microscopy. The key temperatures driving chemical reactions and morphological evolutions are clearly identified. While the oxidation may influence nanostructure formation during thin‐film treatment, the dealloying process at the dealloying front involves interactions solely between the dealloying elements, highlighting the availability and viability of the selected systems. Further, this approach enables efficient exploration of the dealloying process and validation of ML predictions, thereby accelerating the discovery of thin‐film SSMD systems with targeted nanostructures.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Parametric Finite Element Analysis of Naturally Corroded Steel Specimens Using 3D Surface Laser Scans

Corrosion is considered a uniform thickness reduction design guideline of the maritime industry. However, additionally, the corroded and irregular morphology of the surface affects the steel's load-bearing capacity and its impact on the strength and elongation behaviour of the steel is not yet fully understood. These effects on the local behaviour of steel structures under tensile loading were investigated with tensile tests on naturally corroded steel specimens and nonlinear finite element simulations including the corroded surface morphology with a uniform surface idealation. The models also include the deformed specimen shape. The developed approach led to highly accurate parametric finite element models predicting the ultimate tensile strength and longitudinal position of fracture. The results show that all included aspects are essential for accurate simulations, while solely the maximum available surface resolution was not as decisive.

corrosion↗
DOE OSTI2025

Attempting to Develop the World’s Most Cost-Effective Metal 3D Printing Technology Through Industrial Adoption of a High-Temperature Electro-Magnetic Nozzle for 3D Printing and Computer Numerical Control Integration

This project aimed to make a practical system capable of sustained metal deposition in air engineered with industrial integration and controls. The Al-Ce wire feedstock was tailored with appropriate deposition and solidification properties for direct reactive interface printing (DRIP), and the goal was to integrate onto a Hybrid Manufacturing Technologies system for producing test parts without a controlled environment.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Attempting to Develop the World’s Most Cost-Effective Metal 3D Printing Technology Through Industrial Adoption of a High-Temperature Electro-Magnetic Nozzle for 3D Printing and Computer Numerical Control Integration

This project aimed to make a practical system capable of sustained metal deposition in air engineered with industrial integration and controls. The Al-Ce wire feedstock was tailored with appropriate deposition and solidification properties for direct reactive interface printing (DRIP), and the goal was to integrate onto a Hybrid Manufacturing Technologies system for producing test parts without a controlled environment.

36 MATERIALS SCIENCE↗
DOE OSTI2025

3D modeling of n = 1 RMP driven heat fluxes on the SPARC tokamak PFCs using HEAT

3D heat flux calculations at the lower outer divertor plate of SPARC using the HEAT code show that 3D fields generated from error field correction coils can lead to enhanced peak heat fluxes up to 15 times larger compared to the axisymmetric case. Previously employed to simulate axisymmetric heat flux on 3D plasma facing components, the HEAT code can now predict 3D heat flux generated by non-axisymmetric plasmas. This is achieved via a new HEAT module which leverages the 3D field line tracing capabilities of MAFOT starting from an M3D-C1 (MHD resistive code) perturbed equilibria. The resulting heat flux is assigned using the magnetic footprint and the heat flux layer model, an extension of the 2D heat flux model also known as the Eich, to 3D non-axisymmetric plasmas. For SPARC, the new capabilities of HEAT are used to calculate the 3D heat loads resulting from n = 1 perturbation fields (with n indicating the toroidal periodicity) applied through a toroidal array of six picture frame coils with different amplitude. The comparison with the unperturbed case shows significant changes in shape and intensity of the heat flux profile. The results show that the application of n = 1 3D field leads to a localized enhancement of the heat flux peak, influenced by the wetted area impacted by the magnetic footprint, and the appearance of a secondary heat flux peak, whose intensity depends on amplitude of the applied 3D field and toroidal location.

3D heat flux↗
DOE OSTI2026

Performance assessment of 3D printed multi-material energy absorber for automotive bumper: pedestrian lower extremity protection

Designing an energy absorber for automotive bumpers involves balancing low-speed and high-speed impacts to ensure safety, reduce repair costs, and meet regulatory standards. Here, this study explores a novel design using multi-material 3D printing and structural optimization to fabricate a lightweight and cost-efficient energy absorber. The design effectively dissipates energy in low-speed collisions and minimizes force transmission in high-speed pedestrain impacts, helping to meet both safety and performance requirements. The energy absorber design combines 20% carbon fiber-reinforced acrylonitrile butadiene styrene (CF-ABS) and thermoplastic polyurethane (TPU) for optimal stiffness and flexibility. It uses 3D-printed lattice structures optimized through finite element simulations to help meet both low-speed and high-speed impact requirements. Full-scale energy absorbers were 3D-printed using optimized CF-ABS/TPU blends and tested under high-speed impact using the Flexible Pedestrian Legform Impactor (Flex-PLI). For fair comparison, a baseline bumper with a traditional triangular lattice structure, also 3D-printed from the same CF-ABS/TPU materials, was similarly tested. Interestingly, both the optimized and baseline 3D-printed energy absorbers showed nearly identical performance, successfully meeting injury limits. Their performances were also benchmarked against an injection-molded energy absorber. While both 3D-printed and injection-molded designs met injury limits, the 3D-printed absorber exhibited a higher tibia bending moment, indicating an opportunity for further optimization. A Techno-Economic Analysis compared the costs of producing energy absorbers using traditional manufacturing and 3D printing. The analysis highlighted that 3D printing offers cost benefits for low to medium production volumes, with the total cost per energy absorber at ∼ $\$$74, compared to traditional methods that become economical beyond 2000 units.

Additive manufacturing↗
DOE OSTI2025

Emulation of radiation transport in 3D stochastic media using 1D planar Monte Carlo stochastic media radiation transport algorithms

A subset of stochastic media radiation transport problems involves those in which radiation is incident on a thin slab of stochastic material. Particle tracking in 3D for such problems is expensive, and 1D planar models lack accuracy because they only allow the material to change in one dimension. Therefore, we propose dimensional emulation, which through a slight modification allows existing 1D planar geometry stochastic media radiation transport models to reproduce results from the equivalent 3D models by allowing the material to change in all three dimensions, reproducing the fidelity of the 3D model for the low computational cost of the 1D planar model. In this work, we apply dimensional emulation to three Monte Carlo stochastic media radiation transport models: Chord Length Sampling (CLS), the Local Realization Preserving method (LRP), and a variant of Conditional Point Sampling (CoPS). For a common Markovian benchmark set, the 3D emulation variants of these algorithms are numerically verified to reproduce the results of the 3D variants within statistics while running 1.3 to 2 times faster in the implementation within Sandia National Laboratories open-source research code PlaybookMC. The 3D emulation variants are also shown to yield a 72%–92% reduction in error for the thin slab problems in comparison to the 1D benchmark. As a result, the 3D emulation variant of CLS and CoPS-1 are shown to reproduce 3D CLS results that were used to approximate results for a 3D spherical inclusion geometry benchmark set.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2025

Fabrication of a novel 3D-printed perfusion bioreactor for complex cell culture models

We introduce a novel fabrication method for developing a 3D-printed perfusion bioreactor (3D-PBR) to facilitate the in situ growth and differentiation of human bone marrow (BM)-derived mesenchymal stem cells (MSCs) while enabling coculture with vascular cells. To recapitulate human physiology, in vitro platforms must incorporate several key features of their native target organ. This often entails a supportive 3D architecture for growing and differentiating multiple human cell types in situ under perfusion. Other essential characteristics include reproducibility, ease of customization, and biocompatibility. Our 3D-PBR combines these features and was fabricated using a biocompatible resin-based polymer, which was 3D-printed, followed by the addition of a permeable membrane to create a coculture microenvironment. MSCs were encapsulated in a collagen-fibrin gel alongside human endothelium within the 3D-PBR. The physical cues that our 3D-PBR provided facilitated the differentiation of MSCs into specific lineages, such as adipocytes and osteoblasts. Immunohistochemistry images demonstrated that cells grown in the 3D-PBR exhibited more physiologically relevant BM perivascular niche markers compared to static culture models. Our method utilizes emerging 3D printing techniques and alternative materials, departing from traditional PDMS-based soft lithography. These advancements in fabrication further enhance in vitro platforms for diverse cell culture models and vascular permeability assays.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2025

3D-printed micro ion trap technology for quantum information applications

Trapped-ion applications, such as in quantum information processing1, precision measurements, optical clocks and mass spectrometry, rely on specialized high-performance ion traps. The last three of these applications typically use traditional machining to customize macroscopic 3D Paul traps, whereas quantum information processing experiments usually rely on photolithographic techniques to miniaturize the traps and meet scalability requirements. Using photolithography, however, it is challenging to fabricate the complex 3D electrode structures required for optimal confinement. Here, in this work, we demonstrate a high-resolution 3D printing technology based on two-photon polymerization (2PP) that is capable of fabricating large arrays of high-performance miniaturized 3D traps. We show that 3D-printed ion traps combine the advantages, such as strong radial confinement, of traditionally machined 3D traps with on-chip miniaturization. We trap calcium ions in 3D-printed ion traps with radial trap frequencies ranging from 2 MHz to 24 MHz. The tight confinement eases ion cooling requirements and allows us to implement high-quality Rabi oscillations with Doppler cooling only. Also, we demonstrate a two-qubit gate with a Bell-state fidelity of 0.978 ± 0.012. With 3D printing technology, the design freedom is greatly expanded without sacrificing scalability and precision, so that ion trap geometries can be optimized for higher performance and better functionality.

quantum information↗
DOE OSTI2025

Exploring strain rate effects upon 3D materials using high speed in situ X-ray tomoscopy

Cellular materials are ubiquitous in our modern society. They may be stochastic gas-blown foams (e.g., polyurethane), foamed starches (e.g., cereals), or, in this case, 3D printed microlattices. Failure in these materials is often driven by surface or sub-surface defects, which may be nucleated at a surface roughness, an interior void, or inclusion interfaces that may not be typically observable. Obfuscating our understanding further, bulk materials are known to exhibit strain-rate-dependent mechanical response, making a subsurface understanding of damage even more critical. For the first time, an in situ uniaxial mechanical loading stage that simultaneously rotates specimens up to 18 Hz was fielded at a synchrotron for 3D tomographic imaging. This capability opens a plethora of materials science opportunities to explore strain rate effects in materials and examining deformation, fracture, and delamination’s (in composites) for a complete 3D picture (movie) of material response. We demonstrate the deformation of 3D printed polymer lattice structures, of three different material types, at 0.25, 1.1, and 2.2 s −1 strain rates. We successfully imaged the 3D deformation of these materials and can directly compare the same printed structure to the three material types at three strain rates, all in 3D. Material point method simulations were applied to one of the materials to better understand the role of voids on the 3D printed structure’s performance.

36 MATERIALS SCIENCE↗