Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “25 - ENERGY STORAGE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Changes in spectral properties of detached birch leaves

A study conducted in order to determine the rate of changes in spectral properties of detached leaves and to evaluate the effectiveness of low temperature and cytokinins for delaying the changes, is examined. For five minutes, leaves from red birch are immersed in water or 0.001 M BAP, and then stored in plastic bags in the dark at either 5 or 25 C. Using a spectroradiometer and an integrating sphere, total directional-hemispherical reflectance and transmittance of the adaxial surface of the leaves are measured over the 400-1100 nm wavelength region. The results indicate that for leaves stored at 5 C for one week, the changes in the spectral properties are less than 5 percent of the initial values, whereas storage at 25 C promotes rapid senescence and large changes in the spectral properties. It is shown that low temperature is more effective than BAP in delaying senescence.

Daughtry, C. S. T.↗
NASA NTRS1984

Changes in spectral properties of detached leaves

If leaf senescence can be delayed for several days without significant changes in spectral properties, then samples of leaves at remote test sites could be prepared and shipped to laboratories to measure spectral properties. The changes in spectral properties of detached leaves were determined. Leaves from red birch and red pine were immersed in water or 0.001 M benzylaminopurine (BAP) and stored in plastic bags in the dark at either 5 or 25 C. Total directional-hemispherical reflectance and transmittance of the adaxial surface of birch leaves were measured over the 400 to 1100 nm wavelength region with a spectroradiometer and integrating sphere. Pine needles were taped together and reflectance of the mat of needles was measured. Spectral properties changed less than 5% of initial values during the first week when leaves were stored at 5 C. Storage at 25 C promoted rapid senescence and large changes in spectral properties. BAP delayed, but did not stop, senescence at 25 C.

Daughtry, C. S. T.↗
DOE OSTI2025

Initiator‐Driven Tailoring of Reactivity and Inhibition in Frontally Polymerized Dicyclopentadiene‐Co‐Dihydrofuran Thermosets

Incorporating 2,3‐dihydrofuran (DHF) into dicyclopentadiene (DCPD) enables frontally polymerizable, deconstructible thermosets via acid hydrolysis. At 5–20 mol% DHF and low initiator concentration (~100 ppm), DHF inhibits front propagation, lowers the glass transition temperature ( T g ) by up to 20°C, and quenches the front, especially at 20% DHF. This paper demonstrates that increasing the initiator concentration to 250–1000 ppm overcomes inhibition, enhances front speeds by ~50%, and suppresses quenching at the expense of pot‐life. Above 5 mol% DHF, an emergence of a second exotherm is observed, attributed to increased rate dependence on the inhibition of the initiator by DHF. Void formation from volatile DHF is suppressed by applying 110 kPa nitrogen, though at the cost of reduced front speed. Dynamic mechanical analysis shows that higher initiator concentration produced more highly cross‐linked polymers, with a ~20% increase in storage modulus at 25°C and a 20°C increase in T g .

deconstructible thermosets↗
NASA NTRS1985

Balloon-borne video cassette recorders for digital data storage

A high-speed, high-capacity digital data storage system has been developed for a new balloon-borne gamma-ray telescope. The system incorporates sophisticated, yet easy to use and economical consumer products: the portable video cassette recorder (VCR) and a relatively newer item - the digital audio processor. The in-flight recording system employs eight VCRs and will provide a continuous data storage rate of 1.4 megabits/sec throughout a 40 hour balloon flight. Data storage capacity is 25 gigabytes and power consumption is only 10 watts.

Althouse, W. E.↗
NASA NTRS1985

Balloon-borne video cassette recorders for digital data storage

A high speed, high capacity digital data storage system was developed for a new balloon-borne gamma-ray telescope. The system incorporates economical consumer products: the portable video cassette recorder (VCR) and a relatively newer item - the digital audio processor. The in-flight recording system employs eight VCRs and will provide a continuous data storage rate of 1.4 megabits/sec throughout a 40 hour balloon flight. Data storage capacity is 25 gigabytes and power consumption is only 10 watts.

Althouse, W. E.↗
DOE OSTI2026

APS upgrade: Commissioning the world’s first light source based on swap-out injection

The Advanced Photon Source (APS) has recently completed a major upgrade, replacing its 25-year-old storage ring with a cutting-edge hybrid seven-bend achromat lattice enhanced by six additional reverse bends. The new design achieves a natural emittance of 42 pm-rad, enabling the production of X-rays up to 500 times brighter than those generated by the original APS. A key innovation of the upgrade is the implementation of a swap-out injection scheme, which replaces entire depleted bunches instead of performing traditional top-up injection. This approach enables on-axis injection to accommodate for the reduced dynamic aperture resulting from strong focusing. This paper outlines the commissioning process, shares initial operating experience with swap-out injection, and presents performance data for new systems such as the bunch-lengthening cavity.

Sajaev, Vadim [Argonne, PHY]↗
DOE OSTI2025

Sustainable forest management for carbon, wood and biodiversity must consider natural disturbance regimes

Abstract Forests provide multiple benefits that include sequestering carbon, supporting biodiversity, and providing wood products. Managing temperate forests to achieve these benefits sustainably is challenging given the legacy of past human impacts, the complexity of forest development, and increasing but unpredictable disturbances. These intricacies prompted debate about the most effective management of temperate forests to achieve climate mitigation while sustaining forest productivity, regeneration, and diversity. Most research focused on management impacts under relatively stable environmental conditions, whereas forests are facing increasingly frequent and more severe climatic and biotic disturbances. Here, we used a regionally calibrated forest growth model to simulate the effects of forest management on carbon, biodiversity, and wood production under prevalent natural disturbances in the northeastern US. We developed scenarios combining forest management and disturbance regimes based on assumptions of species-specific tree regeneration and mortality rates. We compared passive management with no cutting that prioritizes maintaining existing forest trees with two common regional harvest practices: exploitative timber harvest that prioritizes short-term wood production and regenerative timber harvest that prioritizes regenerating biodiverse native forest tree seedlings. In the absence of natural disturbance, no cutting provides 41% higher forest carbon storage and 50% higher tree structural diversity after 100 years than exploitative or regenerative practices. The presence of drought, windstorm, pest, and disease disturbances altered these outcomes. Regenerative forest management provides 25% higher forest carbon storage and 26% higher tree structural diversity after 100 years than no cutting. Our results demonstrate that wood products and their carbon storage and fossil emission avoidance are important for determining the total climate benefits of forest management under natural disturbances. Our findings highlight that natural disturbance regimes should be considered when selecting management to promote multiple forest benefits, suggesting the need for tailored as opposed to one-size-fits-all policies to sustainably manage temperate forests worldwide.

Liu, Weier (ORCID:0000000265914239)↗
NASA NTRS1982

Voyager spacecraft images of Jupiter and Saturn

The Voyager imaging system is described, noting that it is made up of a narrow-angle and a wide-angle TV camera, each in turn consisting of optics, a filter wheel and shutter assembly, a vidicon tube, and an electronics subsystem. The narrow-angle camera has a focal length of 1500 mm; its field of view is 0.42 deg and its focal ratio is f/8.5. For the wide-angle camera, the focal length is 200 mm, the field of view 3.2 deg, and the focal ratio of f/3.5. Images are exposed by each camera through one of eight filters in the filter wheel on the photoconductive surface of a magnetically focused and deflected vidicon having a diameter of 25 mm. The vidicon storage surface (target) is a selenium-sulfur film having an active area of 11.14 x 11.14 mm; it holds a frame consisting of 800 lines with 800 picture elements per line. Pictures of Jupiter, Saturn, and their moons are presented, with short descriptions given of the area being viewed.

Birnbaum, M. M.↗
NASA NTRS1983

Hyperfiltration wash water recovery subsystem - Design and test results

The Hyperfiltration Wash Water Recovery (HWWR) subsystem, designed to offer low-power high-volume wash water purification for extended mission spacecraft, is discussed in terms of preprototype design and configuration. Heated wash water collected from the shower, hand wash, and laundry flows into a temperature-controlled (374 K) waste storage tank. Two parallel 25 micron absolute filters at the tank outlet remove large particles from the feed stream. A positive displacement feed pump delivers wash water to the hyperfiltration module at a constant flow rate of 0.20 lpm with discharge pressure variations from 4181-7239 Kpa. The hyperfiltration membrane module is a single-pass design including 36 porous stainless steel tubes, and is designed to provide an approximate water recovery rate of 90 percent. Permeate and brine water flows are monitored by flow meters, and removal of urea and ammonia is achieved by adding 15 percent NaOCl solution to the permeate fluid stream. An alternate module design using two diameters of tubing (allowing a smaller pressure drop and a larger membrane area) gave a superior predicted performance over the first module with larger tubing throughout.

Reysa, R. P.↗
NASA NTRS1972

Modular thermal analyzer routine, volume 1

The Modular Thermal Analyzer Routine (MOTAR) is a general thermal analysis routine with strong capabilities for performing thermal analysis of systems containing flowing fluids, fluid system controls (valves, heat exchangers, etc.), life support systems, and thermal radiation situations. Its modular organization permits the analysis of a very wide range of thermal problems for simple problems containing a few conduction nodes to those containing complicated flow and radiation analysis with each problem type being analyzed with peak computational efficiency and maximum ease of use. The organization and programming methods applied to MOTAR achieved a high degree of computer utilization efficiency in terms of computer execution time and storage space required for a given problem. The computer time required to perform a given problem on MOTAR is approximately 40 to 50 percent that required for the currently existing widely used routines. The computer storage requirement for MOTAR is approximately 25 percent more than the most commonly used routines for the most simple problems but the data storage techniques for the more complicated options should save a considerable amount of space.

Oren, J. A.↗
DOE OSTI2026

Enhancing Room-Temperature Hydrogen Storage Properties in Ti–V–Cr–Nb–Mo/Fe Multielement Alloys via Substitutional Tuning

Building upon previously reported high-entropy alloys (HEA) in the Ti−V−Cr−Nb−Mo/Fe compositional space, this study presents a novel bcc alloy containing 6 at. % of the earthabundant element Fe, exhibiting enhanced hydrogen storage properties at room temperature (25 °C). The optimized bcc Ti 23 V 30 Nb 10 Cr 31 Fe 6 alloy rapidly absorbs hydrogen at room temperature with a maximum gravimetric capacity of 3.4 wt % and an enthalpy of hydride formation of −34 kJ/mol H 2 . This value is among the lowest reported to date for bcc HEAs. The reversible capacity of this alloy remains stable at 2.0 wt % upon 20 absorption/desorption cycles at room temperature, which is among the highest reported values for this material class. Collectively, these advances highlight the potential of Fecontaining multielement alloys as efficient and economical candidates for next-generation hydrogen storage systems.

08 HYDROGEN↗
DOE OSTI2025

ROOT RNTuple and EOS: The Next Generation of Event Data I/O

For several years, the ROOT team is developing the new RNTuple I/O subsystem in preparation of the next generation of collider experiments. Both HL-LHC and DUNE are expected to start data taking by the end of this decade. They pose unprecedented challenges to event data I/O in terms of data rates, event sizes, and event complexity. At the same time, the I/O landscape is becoming more diverse. HPC cluster file systems and object stores, NVMe disk cache layers in analysis facilities, and S3 storage on cloud resources are mixing with traditional XRootD-managed spinning disk pools.The ROOT team will finalize a first production version of the RNTuple binary format by the end of 2024. After this point, ROOT will provide backward compatibility for RNTuple data. This contribution provides an overview of the RNTuple feature set, the related R&D activities and the long-term vision for RNTuple. We report on performance, interface design, tooling, robustness, integration with experiment frameworks, and validation results, as well as recent R&D on parallel reading and writing and exploitation of modern hardware and storage systems. We will give an outlook on possible future features after a first production release.Collaboratively, the IT and EP departments at CERN have launched a formal project within the Research and Computing sector to evaluate the novel data format for physics analysis data utilized in LHC experiments and other fields. This part of the project focuses on validating the scalability of the EOS storage backend during the transition from the over 25 years old TTree production format to the newly developed RNTuple format, using both replicated and erasure-coded storage profiles.

Blomer, Jakob [CERN]↗
NASA NTRS1984

High Curie temperature drive layer materials for ion-implanted magnetic bubble devices

Ion implantation of bubble garnets can lower the Curie temperature by 70 C or more, thus limiting high temperature operation of devices with ion-implanted propagation patterns. Therefore, double-layer materials were made with a conventional 2-micron bubble storage layer capped by an ion-implantable drive layer of high Curie temperature, high magnetostriction material. Contiguous disk test patterns were implanted with varying doses of a typical triple implant. Quality of propagation was judged by quasistatic tests on 8-micron period major and minor loops. Variations of magnetization, uniaxial anisotropy, implant dose, and magnetostriction were investigated to ensure optimum flux matching, good charged wall coupling, and wide operating margins. The most successful drive layer compositions were in the systems (SmDyLuCa)3(FeSi)5O12 and (BiGdTmCa)3(FeSi)5O12 and had Curie temperatures 25-44 C higher than the storage layers.

Fratello, V. J.↗
NASA NTRS1984

Large-memory real-time multichannel multiplexed pattern recognition

The principle and experimental design of a real-time multichannel multiplexed optical pattern recognition system via use of a 25-focus dichromated gelatin holographic lens (hololens) are described. Each of the 25 foci of the hololens may have a storage and matched filtering capability approaching that of a single-lens correlator. If the space-bandwidth product of an input image is limited, as is true in most practical cases, the 25-focus hololens system has 25 times the capability of a single lens. Experimental results have shown that the interfilter noise is not serious. The system has already demonstrated the storage and recognition of over 70 matched filters - which is a larger capacity than any optical pattern recognition system reported to date.

Gregory, D. A.↗
NASA NTRS1971

The silicon vidicon: Integration, storage and slow scan capability - Experimental observation of a secondary mode of operation.

Description of the performance of the silicon diode array vidicon - an imaging sensor which possesses wide spectral response, high quantum efficiency, and linear response. These characteristics, in addition to its inherent ruggedness, simplicity, and long-term stability and operating life make this device potentially of great usefulness for ground-base and spaceborne planetary and stellar imaging applications. However, integration and charged storage for periods greater than approximately five seconds are not possible at room temperature because of diode saturation from dark current buildup. Since dark current can be reduced by cooling, measurements were made in the range from -65 to 25 C. Results are presented on the extension of integration, storage, and slow scan capabilities achievable by cooling. Integration times in excess of 20 minutes were achieved at the lowest temperatures. The measured results are compared with results obtained with other types of sensors and the advantages of the silicon diode array vidicon for imaging applications are discussed.

Ando, K. J.↗
NASA NTRS1973

Wind power systems for individual applications

A small windpower system is described which is suitable for electrifying a house. The self-contained unit consists of a two kilowatt wind driven generator, a set of 19 storage batteries, a small dc to ac inverter, and a gasoline generator for use as an emergency backup system in case of prolonged calm periods. Cost effectiveness of the electricity generated by this windmill system comes out to about 15 cents per kilowatt hour - assuming a 10 year life for the batteries and a 20 year life for the other components. Some other small windpower systems are also described, and it is shown that a windpowered generator in the 15- to 25-kilowatt output range coupled to a direct heated water storage system is able to heat a typical New England home.

Clews, H. M.↗
NASA NTRS1980

Storage peak gas-turbine power unit

A storage gas-turbine power plant using a two-cylinder compressor with intermediate cooling is studied. On the basis of measured characteristics of a .25 Mw compressor computer calculations of the parameters of the loading process of a constant capacity storage unit (05.3 million cu m) were carried out. The required compressor power as a function of time with and without final cooling was computed. Parameters of maximum loading and discharging of the storage unit were calculated, and it was found that for the complete loading of a fully unloaded storage unit, a capacity of 1 to 1.5 million cubic meters is required, depending on the final cooling.

Tsinkotski, B.↗