Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “power efficiency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,783 records · Page 99

High-efficiency photovoltaics based on semiconductor nanostructures

The objective of this project was to exploit a variety of semiconductor nanostructures, specifically semiconductor quantum wells, quantum dots, and nanowires, to achieve high power conversion efficiency in photovoltaic devices. In a thin-film device geometry, the objectives were to design, fabricate, and characterize quantum-well and quantum-dot solar cells in which scattering from metallic and/or dielectric nanostructures was employed to direct incident photons into lateral, optically confined paths within a thin (~1-3um or less) device structure. Fundamental issues concerning nonequilibrium carrier escape from quantum-confined structures, removal of thin-film devices from an epitaxial growth substrate, and coherent light trapping in thin-film photovoltaic devices were investigated. In a nanowire device geometry, the initial objectives were to engineer vertical nanowire arrays to optimize optical confinement within the nanowires, and to extend this approach to core-shell heterostructures to achieve broad-spectrum absorption while maintaining high open-circuit voltages. Subsequent work extended this approach to include fabrication of nanowire photovoltaic structures on low-cost substrates.

14 SOLAR ENERGY↗

Analytical simulation of SPS system performance, volume 3, phase 3

The simulation model for the Solar Power Satellite spaceantenna and the associated system imperfections are described. Overall power transfer efficiency, the key performance issue, is discussed as a function of the system imperfections. Other system performance measures discussed include average power pattern, mean beam gain reduction, and pointing error.

Kantak, A. V.↗

IMPATT power building blocks for 20 GHz spaceborne transmit amplifier

Single-stage circulator coupled IMPATT building block constituents of a 20-GHz solid state power amplifier (SSPA) currently under development for spaceborne downlink transmitter usage have been demonstrated as providing 1.5 to 2.0W RF power output at 4 to 5 dB operating gain over a 1 GHz bandwidth. Using either commercially available or recently developed in-house GaAs Schottky Read-profile IMPATT diodes, DC/RF power added efficiencies of 14 to 15% were achieved in these amplifier stages. A two stage IMPATT driver amplifier with similar RF output power capability exhibited 13 + or - 0.5 dB operating gain over a 1 GHz bandwidth.

Asmus, J.↗

Master-Oscillator/Power-Amplifier Laser System

Master-oscillator/power-amplifier (MOPA) laser system operates in continuous-wave mode or in amplitude-modulation (e.g., pulse) mode by modulation of oscillator current. Power amplifier is laser-diode-pumped neodymium:yttrium lithium fluoride (Nd:YLF) laser; oscillator is laser diode. Offers relatively high efficiency and power. Because drive current to oscillator modulated, external electro-optical modulator not needed. Potential uses include free-space optical communications, coded laser ranging, and generation of high-power, mode-locked pulses.

Yu, Anthony W.↗

Organic photovoltaic cell incorporating electron conducting exciton blocking layers

The present disclosure relates to photosensitive optoelectronic devices including a compound blocking layer located between an acceptor material and a cathode, the compound blocking layer including: at least one electron conducting material, and at least one wide-gap electron conducting exciton blocking layer. For example, 3,4,9,10 perylenetetracarboxylic bisbenzimidazole (PTCBI) and 1,4,5,8-napthalene-tetracarboxylic-dianhydride (NTCDA) function as electron conducting and exciton blocking layers when interposed between the acceptor layer and cathode. Both materials serve as efficient electron conductors, leading to a fill factor as high as 0.70. By using an NTCDA/PTCBI compound blocking layer structure increased power conversion efficiency is achieved, compared to an analogous device using a conventional blocking layers shown to conduct electrons via damage-induced midgap states.

14 SOLAR ENERGY↗

Infrared transmissive concentrated photovoltaics for coupling solar electric energy conversion to solar thermal energy utilization

The use of photovoltaic (PV) cells to convert solar energy to electricity is becoming increasingly prevalent; however, there are still significant limitations associated with the widespread adoption of PV cells for electricity needs. There is a clear need for a high efficiency solar power system that supplies electricity at a competitive cost and that provides for an on-demand supply of electricity as well as energy storage. By combining aspects of concentrated solar power and concentrated photovoltaics, the present invention provides a device that enables the conversion of sunlight to electricity at very high efficiencies and that enables the transmission of thermal energy to heat storage devices for later use. The disclosed device enables transmissive CPV through the use of a multijunction PV cell mounted on a transparent base. The use of a multijunction cell allows for highly efficient absorption of light above the bandgap of the lowest bandgap subcell. The transparent base permits transmission of a high percentage of the remaining light below the bandgap of the lowest bandgap subcell. The present invention also discloses a method of generating electricity through the use of a transmissive CPV device. Sunlight is concentrated onto one or more surfaces of the device. High energy light is absorbed by a multijunction PV cell and converted directly to electricity, while low energy light is transmitted through the device into a thermal storage device, which may then be coupled to a heat engine to generate dispatchable electricity.

Escarra, Matthew David↗

Nanoscale Amorphization of Poly(Triarylamine) for Efficient and Stable Inverted Perovskite Photovoltaics

Perovskite solar modules require hole-selective layers that combine efficient charge extraction, interfacial uniformity and scalable processing. Poly(triarylamine) (PTAA) is widely used in high-performance inverted perovskite photovoltaics, but its nanoscale crystallization and aggregation on indium tin oxide can disrupt film continuity, increase interfacial recombination and limit module stability. Here we show that 4-fluorobenzylphosphonic acid (4FBPA) modifies the surface of indium tin oxide to induce nanoscale amorphization of PTAA, forming a uniform sub-10-nm hole-selective layer. The molecule binds to indium tin oxide through a dehydration reaction, tunes the work function and surface free energy of the photoanode, and improves energy-level alignment with PTAA. The resulting amorphous PTAA film shows enhanced conductivity and hole extraction, suppresses non-radiative recombination at the buried interface and promotes more uniform perovskite growth. Inverted perovskite solar cells reach a power conversion efficiency of 26.63%, while blade-coated modules achieve a certified quasi-steady-state efficiency of 23.01%. The modules retain 95.9% of their initial efficiency after 2,600 hours of maximum-power-point operation under 1-sun illumination at 65 +- 5 degrees C in nitrogen. These results identify nanoscale amorphization of polymeric hole-selective layers as a route to efficient and stable inverted perovskite photovoltaics.

14 SOLAR ENERGY↗

A leaf-molded transparent triboelectric nanogenerator for smart multifunctional applications

Transparent, flexible and highly efficient portable power sources are essential components of the next generation electronics and optoelectronic devices. However, complicated technology, expensive cost, environmental pollution and low-efficient output have limited its development. Herein, based on periodic contact/separation between human skin and the microstructured polydimethylsiloxane (PDMS) film, we demonstrate a transparent flexible triboelectric nanogenerator (TENG) through a relatively simple, low-cost, environmental-friendly and high-efficient method. For the first time, the natural leaves with rich surface textures were introduced to make microstructures on PDMS films as effective friction surface in the TENG. Furthermore, long silver nanowires (200 µm in length at least) through novel synthesis were assembled as high-performance electrode, resulting in the entirely flexible and transparent TENG. Owing to the unique design, the transparent flexible TENG was eventually obtained with an enhanced output (Voc=56 V; Isc=3.1 μA) and remarkable transparency (88%). Owing to compelling features of the TENG, a self-powered user-interactive wearable system was successfully established by integrating a flexible electrochromic device (ECD). The remarkable color-tunable ability via mechanical control of our system, highly inspired by chameleons, is potentially useful in military camouflage, monitoring human activity visually, as well as replacing performance of face change in Sichuan Opera. Therefore, this research is a substantial advancement toward the construction of transparent nanogenerator and its multifunctional applications in energy conversation, wearable electronics, healthcare, culture experience, and even environmental protection.

42 ENGINEERING↗

Baseline Experimental Results on the Effect of Oil Temperature on Shrouded Meshed Spur Gear Windage Power Loss

Rotorcraft gearbox efficiencies are reduced at increased surface speeds due to viscous and impingement drag on the gear teeth. This windage power loss can affect overall mission range, payload, and frequency of transmission maintenance. Experimental and analytical studies on shrouding for single gears have shown it be potentially effective in mitigating windage power loss. Efficiency studies on unshrouded meshed gears have shown the effect of speed, oil viscosity, temperature, load, lubrication scheme, etc. on gear windage power loss. The open literature does not cite data on shrouded meshed spur gears. Gear windage power loss test results are presented on shrouded meshed spur gears at elevated oil inlet temperatures and constant oil pressure both with and without shrouding. Shroud effectiveness is compared at four oil inlet temperatures. The results are compared to the available literature and follow-up work is outlined.

windage↗

Baseline Experimental Results on the Effect of Oil Temperature on Shrouded Meshed Spur Gear Windage Power Loss

Rotorcraft gearbox efficiencies are reduced at increased surface speeds due to viscous and impingement drag on the gear teeth. This windage power loss can affect overall mission range, payload, and frequency of transmission maintenance. Experimental and analytical studies on shrouding for single gears have shown it to be potentially effective in mitigating windage power loss. Efficiency studies on unshrouded meshed gears have shown the effect of speed, oil viscosity, temperature, load, lubrication scheme, etc. on gear windage power loss. The open literature does not contain experimental test data on shrouded meshed spur gears. Gear windage power loss test results are presented on shrouded meshed spur gears at elevated oil inlet temperatures and constant oil pressure both with and without shrouding. Shroud effectiveness is compared at four oil inlet temperatures. The results are compared to the available literature and follow-up work is outlined.

gear↗

Suppressed Deep Traps and Bandgap Fluctuations in Cu 2 CdSnS 4 Solar Cells with ≈8% Efficiency

The identification of performance-limiting factors is a crucial step in the development of solar cell technologies. Cu 2 ZnSn(S,Se) 4 -based solar cells have shown promising power conversion efficiencies in recent years, but their performance remains inferior compared to other thin-film solar cells. Moreover, the fundamental material characteristics that contribute to this inferior performance are unclear. In this paper, the performance-limiting role of deep-trap-level-inducing 2Cu Zn +Sn Zn defect clusters is revealed by comparing the defect formation energies and optoelectronic characteristics of Cu 2 ZnSnS 4 and Cu 2 CdSnS 4 . It is shown that these deleterious defect clusters can be suppressed by substituting Zn with Cd in a Cu-poor compositional region. The substitution of Zn with Cd also significantly reduces the bandgap fluctuations, despite the similarity in the formation energy of the Cu Zn +Zn Cu and Cu Cd +Cd Cu antisites. Detailed investigation of the Cu 2 CdSnS 4 series with varying Cu/[Cd+Sn] ratios highlights the importance of Cu-poor composition, presumably via the presence of V Cu , in improving the optoelectronic properties of the cation-substituted absorber. Finally, a 7.96% efficient Cu 2 CdSnS 4 solar cell is demonstrated, which shows the highest efficiency among fully cation-substituted absorbers based on Cu 2 ZnSnS 4 .

14 SOLAR ENERGY↗

A radioluminescent nuclear battery using volumetric configuration: 63 Ni solution/ZnS:Cu,Al/InGaP

Energy dense power sources are critical to the development of compact, remote sensors for terrestrial and space applications. Nuclear batteries using β - -emitting radioisotopes possess energy densities 1000 times greater than chemical batteries. Their power generation is a function of β - flux saturation point relative to the planar (2D) configuration, β - range, and semiconductor converter. An approach to increase power density in a beta-photovoltaic (β-PV) nuclear battery is described. By using volumetric (3D) configuration, the radioisotope, nickel-63 ( 63 Ni) in a chloride solution was integrated in a phosphor film (ZnS:Cu,Al) where the β - energy is converted into optical energy. The optical energy was converted to electrical energy via an indium gallium phosphate (InGaP) photovoltaic (PV) cell, which was optimized for low light illumination and closely matched to radioluminescence (RL) spectrum. With 15 mCi of 63 Ni activity, the 3D configuration energy values surpassed 2D configuration results. The highest total power conversion efficiency ($η_t$) of 3D configuration was 0.289% at 200 µm compared 0.0638% for 2D configuration at 50 µm. The highest electrical power and ηt for the 3D configuration were 3.35 nW e /cm 2 at an activity of 30 mCi and 0.289% at an activity of 15 mCi, respectively. By using 3D configuration, the interaction space between the radioisotope source and scintillation material increased, allowing for significant electrical energy output, relative to the 2D configuration. These initial results represent a first step to increase nuclear battery power density from microwatts to milliwatts per 1000 cm 3 with the implementation of higher energy β - sources.

25 ENERGY STORAGE↗

Efficient two-terminal all-perovskite tandem solar cells enabled by high-quality low-bandgap absorber layers

We report that multi-junction all-perovskite tandem solar cells are a promising choice for next-generation solar cells with high efficiency and low fabrication cost. However, the lack of high-quality low-bandgap perovskite absorber layers seriously hampers the development of efficient and stable two-terminal monolithic all-perovskite tandem solar cells. Here, we report a bulk-passivation strategy via incorporation of chlorine, to enlarge grains and reduce electronic disorder in mixed tin-lead low-bandgap (~1.25 eV) perovskite absorber layers. This enables the fabrication of efficient low-bandgap perovskite solar cells using thick absorber layers (~750 nm), which is a requisite for efficient tandem solar cells. Such improvement enables the fabrication of two-terminal all-perovskite tandem solar cells with a champion power conversion efficiency of 21% and steady-state efficiency of 20.7%. Finally, the efficiency is retained to 85% of its initial performance after 80 h of operation under continuous illumination.

14 SOLAR ENERGY↗

Catalyst synthesis under CO 2 electroreduction favours faceting and promotes renewable fuels electrosynthesis

The electrosynthesis of C 2+ hydrocarbons from CO 2 has garnered recent attention in light of the relatively high market price per unit energy input. Today’s low selectivities and stabilities towards C 2+ products at high current densities curtail system energy efficiency, which limits their prospects for economic competitiveness. Here we present a materials processing strategy based on in situ electrodeposition of copper under CO 2 reduction conditions that preferentially expose and maintain Cu(100) facets, which favour the formation of C 2+ products. We observe capping of facets during catalyst synthesis and achieve control over faceting to obtain a 70% increase in the ratio of Cu(100) facets to total facet area. We report a 90% Faradaic efficiency for C 2+ products at a partial current density of 520 mA cm –2 and a full-cell C 2+ power conversion efficiency of 37%. We achieve nearly constant C2H4 selectivity over 65 h operation at 350 mA cm –2 in a membrane electrode assembly electrolyser.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Optimizing photovoltaic performance in CuInS 2 and CdS quantum dot-sensitized solar cells by using an agar-based gel polymer electrolyte

Quantum dot-sensitized solar cells (QDSSCs) offer new opportunities to address the clean energy challenge, being one of the top candidates for third generation photovoltaics. Like dye-sensitized solar cells (DSSCs), QDSSCs normally use liquid electrolytes that suffer from issues such as evaporation or leakage. In this study a gel polysulfide electrolyte was prepared containing a natural polymer, agar, and was used as a quasi-solid-state electrolyte in solar cells to replace the conventional liquid electrolytes. This gel electrolyte shows almost the same conductivity as the liquid one. The solar cells were fabricated using CuInS 2 quantum dots (QDs), previously synthesized, deposited on TiO 2 photoanodes by electrophoretic deposition (EPD). CdS was deposited on TiO 2 by successive ionic layer adsorption and reaction (SILAR). Reduced graphene oxide (RGO)–Cu 2 S, brass, and thin film CuxS were used as counter electrodes. Compared to a liquid polysulfide water based electrolyte, solar cells based on CuInS 2 and CdS using gel polymer electrolyte (GPE) exhibit greater incident photon to current conversion efficiency (IPCE = 51.7% at 520 nm and 72.7% at 440 nm), photocurrent density (J sc = 10.75 and 13.51 mA cm -2 ), and power conversion efficiency (η = 2.97 and 2.98%) while exhibiting significantly enhanced stability. The solar cells employing the agar-based gel polymeric electrolyte are about a factor of 0.20 more stable than using a liquid electrolyte. The higher photovoltaic performance is due to the good conductivity and high wettability as well as the superior permeation capability of the gel electrolyte into the mesoporous matrix of a TiO 2 film

14 SOLAR ENERGY↗

Morphology control enables thickness-insensitive efficient nonfullerene polymer solar cells

Owing to the use of cost-effective materials and excellent stability, nonfullerene polymer solar cells (PSCs) have great potential for realizing large-area industrial production. In contrast to fullerene-based devices, non-fullerene PSCs have exhibited a superior photovoltaic performance with up to 12% efficiency and long-term thermal stability. Presently, one of the major factors hindering industrial production is the high sensitivity of the power conversion efficiency (PCE) to thickness variations, which can significantly affect the manufacturing yields and production costs of roll-to-roll processing. Specifically, the device fill factors and PCEs of many high-efficiency nonfullerene PSCs show a significant loss when the thickness of the active layer is over 100 nm. In order to achieve high output capabilities earlier, there is an urgent need to find a processing method to fabricate high-efficiency thick-film nonfullerene PSCs. Controlling the morphology and performance sensitivity in thick-film non-fullerene devices is a great challenge in the field. In this paper, we present a simple morphology optimization method via thermal annealing to fabricate highly efficient thickness-insensitive non-fullerene PSCs. After this treatment, PBDB-T/IT-M-based nonfullerene PSCs can afford an impressive PCE of up to ~9.4% at an active layer thickness of 250 nm. In addition, the devices with an active layer thickness of 400 nm still maintain a high efficiency close to 9%. The photovoltaic properties and morphology parameters resolved from hard and soft X-ray scattering clearly indicate that thermal annealing plays a key role in improving the film thickness insensitivity for non-fullerene PSCs.

14 SOLAR ENERGY↗

Tailoring Electron-Photon Interaction in Active 3D Photonic-Crystal Architectures

A photonic-crystal is an artificially engineered periodic structure. It is often referred to as an “optical semiconductor” due to its unparallel capability to mold the flow-of-light on-chip, not only in plane (the x-y plane) but also along the third direction. Examples of the unique 3D control-of-light include diffraction less light-guiding, slow light, super prism, negative refraction and high-Q cavity. A new research frontier exists in which the concept of complete control-of-light is utilized to facilitate and maximize electron-photon interaction. The close proximity and strong interaction between a photonic-crystal and an electronic medium can lead to new optoelectronic properties not easily attainable by other means. In this program, we will study this new class of active photonic-crystal and to achieve improved device performances and basic discoveries. Under this program, the PI has made significant progress in the following areas: (i) We have maximized light trapping and absorption by a 3D simple-cubic photonic-crystal; By advancing the concept of simple-cubic symmetry design, we have successfully designed a super thin-film architecture for high efficiency, crystalline silicon solar cells; Most recently, we have provided a theoretical roadmap for thin-film silicon solar cells with 30% power conversion efficiency. (ii) In the modification of thermal radiation area, we have observed quasi- optical coherence in thermal radiation from a 3D metallic photonic-crystal; Furthermore, we have made a direct confirmation of super-Planckian radiation a tungsten photonic-crystal; (iii) We have made simultaneous observation of a large light diffraction-efficiency, 82%, and efficiency enhancement by a volume hologram material (PQ-PMMA) for solar concentration application. (iv) we have also successfully fabricated a 3D metal-oxide photonic crystal. We demonstrated that this TiO 2 photonic crystal can achieve an effectively infinite optical path-length created using a simple-cubic photonic crystal for extreme light trapping.

36 MATERIALS SCIENCE↗

Performance of computer-designed small-sized four-stage depressed collector for operation of dual-mode traveling wave tube

A computer-designed axisymmetric 2.4-cm-diameter four-stage depressed collectors was evaluated in conjunction with an octave bandwidth, dual-mode traveling wave tube (TWT). The TWT was operated over a wide range of conditions to simulate different applications. The collector performance was optimized (within the constraint of fixed collector geometry which was designed for operation of the TWT at saturation) over the range of TWT operating conditons covered. For operation of the dual-mode TWT at saturation, average collector efficiencies of 81 1/2 and 82 percent for the high and low modes, respectively, were obtained across an octave bandwidth, leading to a three-fold increase in the TWT overall efficiency. For operation of the TWT in the linear, low distortion range, collector efficiencies of 87 to 92 percent were obtained, leading to TWT overall efficiencies as high as 35 percent. For operation of the dual-mode TWT over a 10 to 1 range in output power, overall efficiencies of 14 to 41 percent were obtained.

Ramins, P.↗