Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ignition system”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,783 records · Page 99

Apollo 16 LM-11 descent propulsion system final flight evaluation

The performance of the LM-11 Descent Propulsion System during the Apollo 16 Mission was evaluated and found to be satisfactory. The average engine effective specific impulse was 0.1 second higher than predicted, but well within the predicted 1 sigma uncertainty of 0.2 seconds. The engine performance corrected to standard inlet conditions for the FTP portion of the burn at 50 seconds after ignition was as follows: thrust, 9839 lbf; specific impulse, 306.9 sec; and propellant mixture ratio, 1.592. These values are +0.34, +0.03 and +0.0 percent different, respectively, from the values reported from engine acceptance tests and were within specification limits. Several flight measurement discrepancies that existed during the flight are discussed.

Avvenire, A. T.↗

Space Shuttle production verification motor 1 (PV-1) field joint protection system, volume 7

The performance of the field joint protection system (FJPS) of the Space Shuttle Production Verification Motor 1 (PV-1), as evaluated by postfire hardware inspection. Compliance with the specifications is shown for the FJPS assembly and components. The simplified FJPS and field joint heaters performed nominally, maintaining all joint seal temperatures within the required range. One anomally was noted on the igniter-to-case joint heater during postfire inspection. The heater buckled off the surface in two areas, resulting in two hot spots on the heater and darkened heater insulation. The condition did not affect heater performance during ignition countdown and all igniter seals were maintained within required temperature limits.

Wilkinson, J. P.↗

Determination of Autogenous Ignition Temperature for Isopropyl Alcohol and Ethanol

As part of a recent liquid rocket engine shutdown investigation, a commercial partner requested that NASA provide the autogenous ignition (or autoignition) temperature (AIT) of isopropyl alcohol (IPA). NASA provided the available data, but the data were somewhat scattered, likely due to test configuration and test technique differences. NASA Engineering and Safety Center (NESC) support was requested to experimentally determine the AIT of IPA and ethanol, both of which are extensively applied to propulsion systems. This report contains the outcome of the NESC assessment.

Autoignition Temperature; Isopropyl Alcohol; Comme↗

The Effects of Fuel Characteristics on Stoichiometric Spark-Assisted HCCI

The characteristics of fuel lean HCCI operation using a variety of fuels are well known and have been demonstrated using different engine concepts in the past. In contrast, stoichiometric operation of HCCI is less well documented. Recent studies have highlighted the benefits of operating at a stoichiometric condition in terms of load expansion combined with the applicability of three way catalyst technology to reduce NOx emissions. In this study the characterization of stoichiometric HCCI using gasoline-like fuels was undertaken. The fuels investigated are gasoline, a 50 vol% blend of iso-butanol and gasoline (IB50), and an 85% vol blend of ethanol and gasoline (E85). A single cylinder engine operating with direct injection and spark assist combined with a fully variable hydraulic valve actuation system allowed a wide range of operating parameters to be studied. The resultant fuel properties which differed in terms of octane rating, fuel oxygenation and heat of vaporization show that stoichiometric HCCI is possible using a range of fuels but that these fuel characteristics do have some effect on the combustion characteristics. How these fuel properties can enable an increased engine operating envelope to be achieved, in comparison with both fuel lean HCCI and conventional spark ignited combustion, is then discussed.

02 PETROLEUM↗

Design, Assembly, and Testing of the Neutron Imaging Lens for the National Ignition Facility

The National Ignition Facility will begin testing DT fuel capsules yielding greater than 10^13 neutrons during 2010. Neutron imaging is an important diagnostic for understanding capsule behavior. Neutrons are imaged at a scintillator after passing through a pinhole. The pixelated, 160-mm square scintillator is made up of ¼ mm diameter rods 50 mm long. Shielding and distance (28 m) are used to preserve the recording diagnostic hardware. Neutron imaging is light starved. We designed a large nine-element collecting lens to relay as much scintillator light as reasonable onto a 75 mm gated microchannel plate (MCP) intensifier. The image from the intensifier’s phosphor passes through a fiber taper onto a CCD camera for digital storage. Alignment of the pinhole and tilting of the scintillator is performed before the relay lens and MCP can be aligned. Careful tilting of the scintillator is done so that each neutron only passes through one rod (no crosstalk allowed). The 3.2 ns decay time scintillator emits light in the deep blue, requiring special glass materials. The glass within the lens housing weighs 26 lbs, with the largest element being 7.7 inches in diameter. The distance between the scintillator and the MCP is only 27 inches. The scintillator emits light with 0.56 NA and the lens collects light at 0.15 NA. Thus, the MCP collects only 7% of the available light. Baffling the stray light is a major concern in the design of the optics. Glass cost considerations, tolerancing, and alignment of this lens system will be discussed.

47 OTHER INSTRUMENTATION↗

The growth and nanothermite reaction of 2Al/3NiO multilayer thin films

Nanothermite NiO–Al is a promising material system for low gas emission heat sources; still, its reactive properties are highly dependent on material processing conditions. In the current study, sputter deposition is used to fabricate highly controlled nanolaminates comprised of alternating NiO and Al layers. Films having an overall stoichiometry of 2Al to 3NiO were produced with different bilayer thicknesses to investigate how ignition and self-sustained, high temperature reactions vary with changes to nanometer-scale periodicity and preheat conditions. Ignition studies were carried out with both hot plate and laser irradiation and compared to slow heating studies in hot-stage x-ray diffraction. Ignition behavior has bilayer thickness and heating rate dependencies. The 2Al/3NiO with λ ≤ 300 nm ignited via solid/solid diffusion mixing (activation energy, E a = 49 ± 3 kJ/mole). Multilayers having λ ≥ 500 nm required a more favorable mixing kinetics of solid/liquid dissolution into molten Al (E a = 30 ± 4 kJ/mole). This solid/liquid dissolution E a is a factor of 5 lower than that of the previously reported powder compacts due to the elimination of a passivating Al oxide layer present on the powder. The reactant mixing mechanism between 300 and 500 nm bilayer thicknesses was dependent on the ignition source's heating rate. The self-propagating reaction velocities of 2Al/3NiO multilayers varied from 0.4 to 2.5 m/s. Pre-heating nanolaminates to temperatures below the onset reaction temperatures associated with forming intermediate nickel aluminides at multilayer interfaces led to increased propagation velocities, whereas pre-heating samples above the onset temperatures inhibited subsequent attempts at laser ignition.

36 MATERIALS SCIENCE↗

Mixing-limited Combustion of Alcohol Fuels in a Diesel Engine

Diesel-fueled, heavy-duty engines are critical to global economies, but unfortunately they are currently coupled to the rising price and challenging emissions of Diesel fuel. Public awareness and increasingly stringent emissions standards have made Diesel OEMs consider possible alternatives to Diesel, including electrification, fuel cells, and spark ignition. While these technologies will likely find success in certain market segments, there are still many applications that will continue to require the performance and liquid-fueled simplicity of Diesel-style engines. Three-way catalysis represents a possible low-cost and highly-effective pathway to reducing Diesel emissions, but that aftertreatment system has typically been incompatible with Diesel operation due to the prohibitively high levels of soot formation at the required stoichiometric fuel-air ratios. This paper explores a possible method of integrating three-way catalysis with Diesel-style engine operation. The proposed concept utilizes a high-temperature combustion system-enabled by a combination of thermal insulation, reduced turbocharger aftercooling, and exhaust gas retention-to combust low-cetane “sootless” fuels like ethanol, methanol, and natural gas in a traditional Diesel-style combustion mode (i.e. mixing-limited diffusive combustion, rather than HCCI-like strategies). The proposed concept has demonstrated the ability to meet EPA 2010 soot emissions limits without a particulate filter, while also maintaining a stoichiometric exhaust composition that is compatible with three-way catalysis. Further, the proposed concept can meet, and even exceed, baseline Diesel engine efficiency by combining the high compression ratio Diesel engine design with reduced heat transfer losses. Finally, use of mixing-limited, Diesel-style combustion drastically simplifies combustion phasing, and limits rate of rise. These early results motivate additional work on this concept, further optimizing components for high-temperature operation on alcohol fuels, and integrating the results into a commercial multi-cylinder engine demonstration.

Blumreiter, Julie↗

High pressure oxygen utilization by NASA.

The conditions of use of oxygen by NASA are severe, since moving liquid oxygen at the rates required by large rocket engines calls for high pressures and high flow velocities. NASA also has requirements for gaseous oxygen systems that operate at pressures above the range of industrial practice. Some of the facts pointing up the need for improved criteria for oxygen handling, and work within NASA aimed at developing them are reviewed. Research on oxygen compatibility at high pressure is described. It is shown that the degradation of mechanical properties, the susceptibility to ignition by various stimuli, and the resistance to burning must be quantitatively defined.

Belles, F. E.↗

QM-8 field joint protection system, volume 7

The pre-launch functioning data of the Field Joint Protection System (JPS) used on QM-8 are presented. Also included is the post fire condition of the JPS components following the test firing of the motor. The JPS components are: field joint heaters; field joint sensors; field joint moisture seal; moisture seal kevlar retaining straps; field joint external extruded cork insulation; vent valve; power cables; and igniter heater.

Hale, Elgie↗

Propulsion Risk Reduction Activities for Non-Toxic Cryogenic Propulsion

The Propulsion and Cryogenics Advanced Development (PCAD) Project s primary objective is to develop propulsion system technologies for non-toxic or "green" propellants. The PCAD project focuses on the development of non-toxic propulsion technologies needed to provide necessary data and relevant experience to support informed decisions on implementation of non-toxic propellants for space missions. Implementation of non-toxic propellants in high performance propulsion systems offers NASA an opportunity to consider other options than current hypergolic propellants. The PCAD Project is emphasizing technology efforts in reaction control system (RCS) thruster designs, ascent main engines (AME), and descent main engines (DME). PCAD has a series of tasks and contracts to conduct risk reduction and/or retirement activities to demonstrate that non-toxic cryogenic propellants can be a feasible option for space missions. Work has focused on 1) reducing the risk of liquid oxygen/liquid methane ignition, demonstrating the key enabling technologies, and validating performance levels for reaction control engines for use on descent and ascent stages; 2) demonstrating the key enabling technologies and validating performance levels for liquid oxygen/liquid methane ascent engines; and 3) demonstrating the key enabling technologies and validating performance levels for deep throttling liquid oxygen/liquid hydrogen descent engines. The progress of these risk reduction and/or retirement activities will be presented.

Smith, Timothy D.↗

STS-1 Forward RCS Oxidizer Tank Subsystem Failure Assessment

The launch of the Space Shuttle Columbia on STS-1 in April 1981 marked the beginning of a new era in American spaceflight. It was the only crewed first flight of a launch vehicle, and was also among the first vehicles to use large solid rockets as primary propulsion. A potential disaster was narrowly averted at liftoff when ignition overpressure waves pulse swept up the Shuttle stack. The frequency of this transient shock wave exceeded pre-launch predictions, and resulted in high, alternating normal accelerations along the length of the vehicle. Among the results of this unexpected loading was failure of an oxidizer tank support strut in the orbiter’s forward reaction control system module, which could have led to loss of the mission, crew and vehicle. This particular incident is investigated in more detail using classical structural mechanics, and the results are discussed to provide additional insight.

Space Shuttle↗

A New Test Methodology for Evaluating Fire Risk Due to Electrical Faults in Oxygen-Enriched Environments

This paper discusses a new test methodology for assessing the safe use of materials found in spacecraft that may be exposed to electrical faults, as performed at the NASA White Sands Test Facility. “Wire-break” testing, modeled after the Cleveland Open Cup method, identifies the conditions under which pyrolyzed material transitions from a brief flash to a propagating flame. The approach focuses on fuel mass liberated through pyrolysis, mixed with oxygen, and ignited by a piloted ignition (spark due to fusion of wire) to achieve flame propagation with the least energy. The test approach attempts to find energy density thresholds derived using I²t values from current-induced heating of various test materials and wire characteristics. The application of the data provides a useful approach to mitigating fire risks in space systems by correlating threshold data to real-world designs and scaling factors, including oxygen pressure, wire diameter, heat sinking, and contained smoke volume. Several case studies, including Apollo missions and hypothetical scenarios, illustrate practical applications of these thresholds to enhance fire safety design considerations in space environments.

methodology↗

Parallel Multi-cycle LES of an Optical Pent-roof DISI Engine Under Motored Operating Conditions

The use of Large-eddy Simulations (LES) has increased due to their ability to resolve the turbulent fluctuations of engine flows and capture the resulting cycle-to-cycle variability. One drawback of LES, however, is the requirement to run multiple engine cycles to obtain the necessary cycle statistics for full validation. The standard method to obtain the cycles by running a single simulation through many engine cycles sequentially can take a long time to complete. Recently, a new strategy has been proposed by our research group to reduce the amount of time necessary to simulate the many engine cycles by running individual engine cycle simulations in parallel. With modern large computing systems this has the potential to reduce the amount of time necessary for a full set of simulated engine cycles to finish by up to an order of magnitude. In this paper, the Parallel Perturbation Methodology (PPM) is used to simulate up to 35 engine cycles of an optically accessible, pent-roof Directinjection Spark-ignition (DISI) engine at two different motored engine operating conditions, one throttled and one un-throttled. Comparisons are made against corresponding sequential-cycle simulations to verify the similarity of results using either methodology. Mean results from the PPM approach are very similar to sequential-cycle results with less than 0.5% difference in pressure and a magnitude structure index (MSI) of 0.95. Differences in cycle-to-cycle variability (CCV) predictions are larger, but close to the statistical uncertainty in the measurement for the number of cycles simulated. PPM LES results were also compared against experimental data. Mean quantities such as pressure or mean velocities were typically matched to within 5- 10%. Pressure CCVs were under-predicted, mostly due to the lack of any perturbations in the pressure boundary conditions between cycles. Velocity CCVs for the simulations had the same average magnitude as experiments, but the experimental data showed greater spatial variation in the root-mean-square (RMS). Conversely, circular standard deviation results showed greater repeatability of the flow directionality and swirl vortex positioning than the simulations.

I.C. Engines↗

A semiconductor bridge ignited hot gas piston ejector

The topics are presented in viewgraph form and include the following: semiconductor bridge technology (SCB); SCB philosophy; technology transfer; simplified sketch of SCB; SCB processing; SCB design; SCB test assembly; 5 mJ SCB burst based on a polaroid photograph; micro-convective heat transfer hypothesis; SCB fire set; comparison of SCB and hot-wire actuators; satellite firing sets; logic fire set; SCB smart component; SCB smart firing set; semiconductor design considerations; and the adjustable actuator system.

Grubelich, M. C.↗

Activation of enriched environmental xenon by 14-MeV neutrons

The international monitoring system exists to verify compliance with the terms of the comprehensive test ban treaty. About 10% of the member stations will be capable of detecting radioxenon, which can be produced in nuclear detonations or through civilian processes. We have studied the activation of radioxenon by the prompt, intense spectrum of 14-MeV neutrons produced at the National Ignition Facility. While 14-MeV neutrons are not currently a significant contributor to the production of radioxenon, we find that radioxenon produced through activation of environmental xenon by 14-MeV neutrons would be distinguishable from activation by nuclear tests.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Self-consistent feedback mechanism for the sudden viscous dissipation of finite-Mach-number compressing turbulence

Previous work [Davidovits and Fisch, Phys. Rev. Lett. 116, 105004 (2016)] demonstrated that the compression of a turbulent field can lead to a sudden viscous dissipation of turbulent kinetic energy (TKE), and that paper suggested this mechanism could potentially be used to design new fast-ignition schemes for inertial confinement fusion (ICF). We expand on previous work here by accounting for finite Mach numbers, rather than relying on a zero-Mach-limit assumption as previously done. The finite-Mach-number formulation is necessary to capture a self-consistent feedback mechanism in which dissipated TKE increases the temperature of the system, which in turn modifies the viscosity and thus the TKE dissipation itself. Direct numerical simulations with a tenth-order accurate Padé scheme were carried out to analyze this self-consistent feedback loop for compressing turbulence. Results show that, for finite Mach numbers, the sudden viscous dissipation of TKE still occurs, for both the solenoidal and dilatational turbulent fields. As the domain is compressed, oscillations in dilatational TKE are encountered due to the highly oscillatory nature of the pressure dilatation. An analysis of the source terms for the internal energy shows that the mechanical-work term dominates the viscous turbulent dissipation. As a result, the effect of the suddenly dissipated TKE on temperature is minimal for the Mach numbers tested. Moreover, an analytical expression is derived that confirms the dissipated TKE does not significantly alter the temperature evolution for low Mach numbers, regardless of compression speed. The self-consistent feedback mechanism is thus quite weak for subsonic turbulence, which could limit its applicability for ICF.

42 ENGINEERING↗

Integrated support structure for GASCAN 2

The focus of the Worcester Polytechnic Institute (WPI) Advanced Space Design Program was the preliminary design of the Integrated Support Structure for GASCAN II, a Get Away Special canister donated by the MITRE Corporation. Two teams of three students each worked on the support structure. There was a structural design team and a thermal design team. The structure will carry three experiments also undergoing preliminary design this year, the mu-gravity Ignition Experiment, the Rotational Flow in Low Gravity Experiment, and the Ionospheric Properties and Propagation Experiment. The structural design team was responsible for the layout of the GASCAN and the preliminary design of the structure itself. They produced the physical interface specifications defining the baseline weights and volumes for the equipment and produced layout drawings of the system. The team produced static and modal finite element analysis of the structure using ANSYS. The thermal design team was responsible for the power and timing requirements of the payload and for the identification and preliminary analysis of potential thermal problems. The team produced the power, timing, and energy interface specifications and assisted in the development of the specification of the battery pack. The thermal parameters of each experiment were cataloged and the experiments were subjected to worst case heat transfer scenarios.

Source record↗

Path-Adaptive Guidance Algorithm Trades for a Two-Stage Lunar Descent Vehicle

For the next generation of NASA’s missions, explicit, path-adaptive descent guidance algorithms must provide the stability and customizability required for a safe and efficient descent to the lunar surface, while also meeting program and vehicle constraints. Several descent algorithms have been flown and tested for single-stage landers through the Apollo and Altair programs, but thus far little analysis has been conducted involving the application of these algorithms to a two-stage descent vehicle. Due to payload mass and fairing constraints of the existing fleet of launch vehicles, multi-stage descent architectures are a unique option for achieving the greatest possible mass to lunar surface. This paper seeks to compare the performance of guidance configurations of a lunar lander system consisting of two stages, one of which separates partway through descent. Through development of this paper, an optimization suite has been written that is specifically designed for optimizing planetary non-atmospheric two-stage descent trajectories, and is used as a baseline to compare the guidance algorithms tested. Time-to-go computational methods and ignition logic routines that may be employed in a lunar environment are also discussed. Preliminary results are presented that show relative performance metrics for a range of different guidance algorithm configurations.

Jason M Everett↗