Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “humidity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,783 records · Page 99

Antimony Chloride Treatments of CdTe-Based Solar Cells

Development of a new SbCl3-based solution treatment for chloride activation of CdTe-based solar cells is described. Activation was confirmed with CdSeTe:Sb devices exhibiting VOC > 550 mV and JSC > 25 mAcm-2. Treatment optimization showed strong effects of annealing time and temperature on cell properties. Material characterization indicated surface conversion of CdSeTe to CdCl2 and Sb2Te3 with SbCl3 treatment. However, no reaction products were formed with treatment under inert conditions, which was coupled with poor device performance. Drying the SbCl3 films at controlled humidity conditions confirmed that exposure to high relative humidity is critical for CdSeTe activation, through hydrolysis of SbCl3. Mechanistic details of SbCl3 speciation during hydrolysis and annealing to activate CdSeTe are discussed.

14 SOLAR ENERGY↗

Traits drive global wood decomposition rates more than climate

Wood decomposition is a major component of the global carbon cycle. Decomposition rates vary across climate gradients, which is thought to reflect the effects of temperature and moisture on the metabolic kinetics of decomposers. However, decomposition rates also vary with wood traits, which may reflect the influence of stoichiometry on decomposer metabolism as well as geometry relating the surface areas that decomposers colonize with the volumes they consume. In this paper, we combined metabolic and geometric scaling theories to formalize hypotheses regarding the drivers of wood decomposition rates, and assessed these hypotheses using a global compilation of data on climate, wood traits, and wood decomposition rates. Our results are consistent with predictions from both metabolic and geometric scaling theories. Approximately half of the global variation in decomposition rates was explained by wood traits (nitrogen content and diameter), whereas only a fifth was explained by climate variables (air temperature, precipitation, and relative humidity). These results indicate that global variation in wood decomposition rates is best explained by stoichiometric and geometric wood traits. Our findings suggest that inclusion of wood traits in global carbon cycle models can improve predictions of carbon fluxes from wood decomposition.

Hu, Zhenhong↗

Accounting for spectroscopic effects in laser‐based open‐path eddy covariance flux measurements

Abstract A significant portion of the production and consumption of trace gases (e.g. CO 2 , CH 4 , N 2 O, NH 3 , etc.) by world ecosystems occurs in areas without sufficient infrastructure or easily available grid power to run traditional closed‐path flux stations. Open‐path analyzer design allows such measurements with power consumption 10–150 times below present closed‐path technologies, helping to considerably expand the global coverage and improve the estimates of gas emissions and budgets, informing the remote sensing and modeling communities and policy decisions, all the way to IPCC reports. Broad‐band nondispersive infrared devices have been used for open‐path CO 2 and H 2 O measurements since the late 1970s, but since recently, a growing number of new narrow‐band laser‐based instruments are being rapidly developed. The new design comes with its own challenges, specifically: (a) mirror contamination, and (b) uncontrolled air temperature, pressure and humidity, affecting both the gas density and the laser spectroscopy of the measurements. While the contamination can be addressed via automated cleaning, and density effects can be addressed via the Webb‐Pearman‐Leuning approach, the spectroscopic effects of the in situ temperature, pressure and humidity fluctuations on laser‐measured densities remain a standing methodological question. Here we propose a concept accounting for such effects in the same manner as Webb et al. proposed to account for respective density effects. Derivations are provided for a general case of flux of any gas, examined using a specific example of CH 4 fluxes from a commercially available analyzer, and then tested using “zero‐flux” experiment. The proposed approach helps reduce errors in open‐path, enclosed, and temperature‐ or pressure‐uncontrolled closed‐path laser‐based flux measurements due to the spectroscopic effects from few percents to multiple folds, leading to methodological advancement and geographical expansion of the use of such systems providing reliable and consistent results for process‐level studies, remote sensing and Earth modeling applications, and GHG policy decision‐making.

Burba, George↗

The response of stomatal conductance to seasonal drought in tropical forests

Stomata regulate CO2 uptake for photosynthesis and water loss through transpiration. The approaches used to represent stomatal conductance (gs) in models vary. In particular, current understanding of drivers of the variation in a key parameter in those models, the slope parameter (i.e. a measure of intrinsic plant water-use-efficiency), is still limited, particularly in the tropics. Here we collected diurnal measurements of leaf gas exchange and water potential (?leaf), and a suite of plant traits from the upper canopy of 15 tropical trees in two contrasting Panamanian forests throughout the dry season of the 2016 El Niño. The plant traits included wood density, leaf-mass-per-area (LMA), leaf carboxylation capacity (Vc,max25), leaf water content, the degree of isohydry, and predawn ?leaf. We first investigated how the choice of four commonly used leaf-level gs models with and without the inclusion of ?leaf as an additional predictor variable influence the ability to predict gs, and then explored the abiotic (i.e. month, site-month interaction) and biotic (i.e. tree-species-specific characteristics) drivers of slope parameter variation. Our results show that the inclusion of ?leaf did not improve model performance and that the models that represent the response of gs to vapor pressure deficit performed better than corresponding models that respond to relative humidity. Within each gs model, we found large variation in the slope parameter, and this variation was attributable to the biotic driver, rather than abiotic drivers. We further investigated potential relationships between the slope parameter and the six available plant traits mentioned above, and found that only one trait, LMA, had a significant correlation with the slope parameter (R2=0.66, n=15), highlighting a potential path towards improved model parameterization. This study advances understanding of gs dynamics over seasonal drought, and identifies a practical, trait-based approach to improve modeling of carbon and water exchange in tropical forests.

carbon and water exchange, stomatal conductance mo↗

Evaluation of a single cell and candidate materials with high water content hydrogen in a generic solid oxide fuel cell stack test fixture, Part II: materials and interface characterization

A generic solid oxide fuel cell (SOFC) test fixture was developed to evaluate candidate materials under realistic conditions. A commerical 50 mm x 50 mm NiO-YSZ anode supported thin YSZ electrolyte cell with lanthanum strontium manganite (LSM) cathode was tested to evaluate the stability of candidate materials. The cell was tested in two stages at 800oC: stage I of low (~3% H2O) humidity and stage II of high (~30% H2O) humidity hydrogen fuel at constant voltage or constant current mode. Part I of the work was published earlier with information of the generic test fixture design, materials, cell performance, and optical post-mortem analysis. In part II, detailed microstructure and interfacial characterizations are reported regarding the SOFC candidate materials: (Mn,Co)-spinel conductive coating, alumina coating for sealing area, ferritic stainless steel interconnect, refractory sealing glass, and their interactions with each other. Overall, the (Mn,Co)-spinel coating was very effective in minimizing Cr migration. No Cr was identified in the cathode after 1720h at 800oC. Aluminization of metallic interconnect also proved to be chemically compatible with alkaline-earth silicate sealing glass. The details of interfacial reaction and microstructure development are discussed.

(Mn,Co)-spinel↗

Constitutive down‐regulation of liguleless alleles in sorghum drives increased productivity and water use efficiency

Plant architecture influences the microenvironment throughout the canopy layer. Plants with a more erect leaf architecture allow for an increase in planting densities and allow more light to reach lower canopy leaves. This is predicted to increase crop carbon assimilation. Frictional resistance to wind reduces air movement in the lower canopy, resulting in higher humidity. By increasing the proportion of canopy photosynthesis in the more humid lower canopy, gains in the efficiency of water use might be expected, although this may be slightly offset by the more open erectophile form canopy. An anatomical feature in members of the Poaceae family that impacts leaf angle is the articulated junction of the sheath and blade, which also bares the ligule and auricles. Mutants, which lack ligules and auricles, show no articulation at this junction, resulting in leaves that are near vertical. In maize, these phenotypes termed liguleless result from null mutations of genes: ZmLG1 (Zm00001eb67740) and ZmLG2 (Zm00001eb147220). In sorghum, SbiRTx430.06G264300 (SbLG1) and SbiRTx430.03G392300 (SbLG2) are annotated as the respective maize homologues. A hair-pin element designed to down-regulate both SbLG1 and SbLG2 was introduced into the grain sorghum genotype RTx430. Derived transgenic events harbouring the hair-pin failed to develop ligules and displayed reduced leaf angles to the vertical, but less vertical than in null mutations. Under field settings, plots sown with these sorghum events having an erect architecture phenotype displayed an increase in photosynthesis in lower canopy levels, which led to increases in above-ground biomass and seed yield, without an increase in water use.

59 BASIC BIOLOGICAL SCIENCES↗

An Investigation of Catastrophic Failure in Solid-State Lamps Exposed to Harsh Environment Operational Conditions

Today’s lighting technology is steadily becoming more energy efficient and less toxic to the environment since the passing of the Energy Independence and Security Act of 2007 (EISA) [1]. EISA has mandated a higher energy efficiency standard for lighting products and the phase out of the common incandescent lamp. This has led lighting manufacturers to pursue solid-state lighting (SSL) technologies for consumer lighting applications. However, two major roadblocks are hindering the transition process to SSL lamps: cost and quality. In order to cut cost, manufactures are moving towards cheaper packaging materials and a variety of package architecture construction techniques which may potentially erode the quality of the lamp and reduce its survivability in everyday applications. Typically, SSL lamps are given product lifetimes of over twenty years based off of the IES TM-21-11 lighting standard which does not include moisture effects or large operational temperatures [2]. A group of recently released off-the-shelf lamps have undergone a steady-state temperature humidity bias life test of 85°C/85%RH (85/85) to investigate the reliability in harsh environment applications. The lack of accelerated test methods for lamps to assess reliability prior to introduction into the marketplace does not exist in literature. There is a need for SSL physics based models for the assessment and prediction of a lamp’s lifetime which is being spearheaded by the DOE [3]. In order to be fully accepted in the marketplace, SSL lamps must be able to perform similarly to incandescent lamps in these environments, as well as live up to the lifetime claims of manufacturers. A lamp’s package architecture must be designed with performance factors in mind, as well as address some of the known and published package related failure mechanisms, such as carbonization of the encapsulant material, delamination, encapsulant yellowing, lens cracking, and phosphor thermal quenching [4]. Each failure mechanism produces the similar failure mode of lumen degradation predominately due to two contributing factors: high junction temperature and moisture ingress. The current state-of-the-art has focused on individual areas of the lamp, such as the LED chip, substrate material, electrical driver design and thermal management techniques. [5] – [16] Looking at the lamp as a whole is a novel approach and has not been seen before in literature. This work followed the JEDEC standard JESD22-A101C of 85/85 with a one hour interval of applied voltage followed by a one hour interval of no applied voltage [17]. This test was performed continuously for each SSL lamp until it became nonoperational, i.e. did not turn on. Periodically, photometric measurements were taken following the IES LM-79-08 standard at room temperature using an integrating sphere, a spectrometer, and lighting software. The overall health of the SSL lamps was assed using the relative luminous flux (RLF), correlated color temperature (CCT) and the color difference (Δu'v') using the Euclidean distance of the CIE 1976 color space coordinates. Finally, a Weibull analysis was completed to compare the characteristic lifetime of the SSL lamp to the actual rated lifetime. An important result from this work shows that the rated lifetime does not come close to the actual lifetime when the SSL lamps are used in a harsh humid environment which is fairly common in outdoor applications across the U.S. Also, the photometric results are presented for the entire lifetime of each SSL lamp under test.

54 ENVIRONMENTAL SCIENCES↗

Transparent conducting impurity-doped ZnO thin films prepared using oxide targets sintered by millimeter-wave heating

The preparation of transparent conducting impurity-doped ZnO thin films by both pulsed laser deposition (PLD) and magnetron sputtering deposition (MSD) using impurity-doped ZnO targets sintered with a newly developed energy saving millimeter-wave (28 GHz) heating technique is described. Al-doped ZnO (AZO) and V-co-doped AZO (AZO:V) targets were prepared by sintering with various impurity contents for 30 min at a temperature of approximately 1250 degree sign C in an air or Ar gas atmosphere using the millimeter-wave heating technique. The resulting resistivity and its thickness dependence obtainable in thin films prepared by PLD using millimeter-wave-sintered AZO targets were comparable to those obtained in thin films prepared by PLD using conventional furnace-sintered AZO targets; a low resistivity on the order of 3x10{sup -4} {Omega} cm was obtained in AZO thin films prepared with an Al content [Al/(Al+Zn) atomic ratio] of 3.2 at. % and a thickness of 100 nm. In addition, the resulting resistivity and its spatial distribution on the substrate surface obtainable in thin films prepared by rf-MSD using a millimeter-wave-sintered AZO target were almost the same as those obtained in thin films prepared by rf-MSD using a conventional powder AZO target. Thin films prepared by PLD using millimeter-wave-sintered AZO:V targets exhibited an improved resistivity stability in a high humidity environment. Thin films deposited with a thickness of approximately 100 nm using an AZO:V target codoped with an Al content of 4 at. % and a V content [V/(V+Zn) atomic ratio] of 0.2 at. % were sufficiently stable when long-term tested in air at 90% relative humidity and 60 degree sign C.

36 MATERIALS SCIENCE↗

Damage by radicals and photons during plasma cleaning of porous low-k SiOCH. II. Water uptake and change in dielectric constant

Porous dielectric materials provide lower capacitances that reduce RC time delays in integrated circuits. Typical low-k materials include porous SiOCH-silicon dioxide with carbon groups, principally CH{sub 3}, lining the pores. With a high porosity, internally connected pores provide pathways for reactive species to enter into the material. Fluorocarbon plasmas are often used to etch SiOCH, a process that leaves a fluorocarbon polymer on the surface that must later be removed. During cleaning using Ar/O{sub 2} or He/H{sub 2} plasmas, reactions of radicals that diffuse into the SiOCH and photons that penetrate into the SiOCH can remove -CH{sub 3} groups. Due to its higher reactivity, cleaning with Ar/O{sub 2} plasmas removes more -CH{sub 3} groups than He/H{sub 2} plasmas, and so produce more free radical sites, such as -SiO{sub 2} Bullet (a -SiO{sub 2}-CH{sub 3} site with the -CH{sub 3} group removed).Upon exposure to humid air, these free radical sites can chemisorb H{sub 2}O to form hydrophilic Si-OH which can further physisorb H{sub 2}O through hydrogen bonding to form Si-OH(H{sub 2}O). With the high dielectric constant of water, even a small percentage of water uptake can significantly increase the effective dielectric constant of SiOCH. In this paper, we report on results from a computational investigation of the cleaning of SiOCH using Ar/O{sub 2} or He/H{sub 2} plasmas and subsequent exposure to humid air. The authors found that plasma cleaning with He/H{sub 2} mixtures produce less demethylation than cleaning with Ar/O{sub 2} plasmas, as so results in less water uptake, and a smaller increase in dielectric constant. The water that produces the increase in dielectric constant is roughly half chemisorbed and half physisorbed, the latter of which can be removed with mild heating. Sealing the pores with NH{sub 3} plasma treatment reduces water uptake and helps prevent the increase in dielectric constant.

36 MATERIALS SCIENCE↗

Vanadium dioxide film protected with an atomic-layer-deposited Al{sub 2}O{sub 3} thin film

A VO{sub 2} film exposed to ambient air is prone to oxidation, which will degrade its thermochromic properties. In this work, the authors deposited an ultrathin Al{sub 2}O{sub 3} film with atomic layer deposition (ALD) to protect the underlying VO{sub 2} film from degradation, and then studied the morphology and crystalline structure of the films. To assess the protectiveness of the Al{sub 2}O{sub 3} capping layer, the authors performed a heating test and a damp heating test. An ultrathin 5-nm-thick ALD Al{sub 2}O{sub 3} film was sufficient to protect the underlying VO{sub 2} film heated at 350 °C. However, in a humid environment at prolonged durations, a thicker ALD Al{sub 2}O{sub 3} film (15 nm) was required to protect the VO{sub 2}. The authors also deposited and studied a TiO{sub 2}/Al{sub 2}O{sub 3} bilayer, which significantly improved the protectiveness of the Al{sub 2}O{sub 3} film in a humid environment.

36 MATERIALS SCIENCE↗

Three-dimensional large-eddy simulations of the early phase of contrail-to-cirrus transition: effects of atmospheric turbulence and radiative transfer

Here, this article presents the results from numerical experiments of the early phase of contrail-cirrus formation using a limited set of fully three-dimensional, high-resolution large-eddy-simulations. The focus is laid on the interplay between atmospheric turbulence and the radiative transfer (and to a limited extent the ambient ice relative humidity), and how this interaction affects the contrail evolution and the characteristics of the resulting contrail-cirrus one hour after emission. Turbulence is sustained via a large-scale stochastic forcing that creates a non-uniform shear in addition to pure turbulent fluctuations. This effect manifests in the formation of vertically sheared structures of ice crystals. When radiative transfer is activated, ice tends to redistribute more uniformly along the vertical direction forming spotty vertical structures. For the conditions analyzed in this study, atmospheric turbulence, inclusive of non-uniform turbulent shear and turbulent fluctuations, affects primarily the contrail width whereas the microphysical properties such ice water path and ice mass are controlled by radiative transfer and relative humidity.

54 ENVIRONMENTAL SCIENCES↗

Modeling Water Uptake and Pt Utilization in High Surface Area Carbon

Local transport losses limit high-current density performance of fuel-cells, especially at low Pt-loadings. Optimizing catalyst-layer structure and material properties to mitigate these losses is critical for wide-scale fuel-cell commercialization. Carbon supports form the primary porous structure of catalyst layers in which Pt particles are deposited and ionomer films are distributed. Unlike non-porous carbon supports, high surface area carbon support is unique in its relative humidity dependent Pt utilization and performance due to presence of Pt particles in the micropores interior of carbon particles. We model water uptake and Pt utilization in catalyst layers with high-surface-area carbon support. Interactions between functional groups on the carbon pore walls and water play a vital role in controlling water uptake from water vapor by catalyst layers. Ionomer is shown to influence proton access in micropores, even though it may not deposit into the micropores.

08 HYDROGEN↗

Resolving Anodic Current and Temperature Distributions in a Polymer Electrolyte Membrane Water Electrolysis Cell Using a Pseudo-Two-Phase Computational Fluid Dynamics Model

Expanding upon our prior experimental work, we constructed a three-dimensional model of a polymer electrolyte membrane water electrolyzer using computational fluid dynamics. We applied the assumption of pseudo-two-phase flow, the flow of two phases with equal velocity. Experimental data were used to obtain parameters and to determine the conditions under which this model was valid. Anodic distributions of current density, temperature, liquid saturation, and relative humidity were obtained at various flow rates. The overall current density and temperature difference from inlet to outlet at the anode agreed strongly with experimental measurements under most circumstances. This verification allowed us to further examine the apparent gas coverage calculated from experimental and model temperature data. Results suggested a low liquid saturation and low relative humidity at the anode due to the consumption of liquid water and water vapor. However, we questioned the accuracy of the pseudo-two-phase assumption at low water feed rates. We concluded that the model was applicable to systems with liquid water feed rates greater than 0.6 ml min -1 cm -2 . Therefore, it is a fair screening method that can advise which operating conditions lead to excessive temperatures or drying at the anode, thereby promoting the longevity of the membrane and catalyst.

25 ENERGY STORAGE↗

Effects of ionomer morphology on oxygen reduction on Pt

In this paper, the oxygen reduction reaction (ORR) at the interface between platinum and Nafion 1100 equivalent weight was studied as a function of temperature (20–80 °C), humidity (10–100%), scan rate, the manner in which Nafion film was deposited, and the state of the Pt surface using ultramicroelectrodes employing cyclic voltammetry and chronoamperometry. ORR on smooth electrodes was strongly inhibited under specific conditions dependent on temperature, humidity, and scan rate. From the data presented, we postulate that dynamic changes in the molecular structure of the ionomer at the platinum interface result in differences in ORR voltammetry for films prepared and equilibrated under different conditions. The lack of similar changes for rough, platinized electrodes has been attributed to differences in initial ionomer structure and a higher energy barrier for ionomer restructuring. Finally, these model system studies yield insight into the ionomer-catalyst interface of particular interest for polymer electrolyte fuel cells.

14 SOLAR ENERGY↗

PV Degradation Tools [SWR-20-71]

This open-source tool functions for calculating degradation of photovoltaic modules. For example, functions to calculate front and rear relative Humidity, as well as Acceleration Factors. A degradation calculation function is also being developed, considering humidity and spectral irradiances models.

Holsapple, Derek↗

A Generalized Subsurface Flow Parameterization Considering Subgrid Spatial Variability of Recharge and Topography

Subsurface flow is an important hydrologic process and a key component of the water budget, especially in humid regions. In this study, a new subsurface flow formulation is developed that incorporates spatial variability of both topography and recharge. It is shown through theoretical derivation and case studies that the power law and exponential subsurface flow parameterizations and the parameterization proposed by Woods et al.[1997] are all special cases of the new formulation. The subsurface flows calculated using the new formulation compare well with values derived from observations at the Tulpehocken Creek and Walnut Creek watersheds. Sensitivity studies show that when the spatial variability of topography or recharge, or both is increased, the subsurface flows increase at the two aforementioned sites and the Maimai hillslope. This is likely due to enhancement of interactions between the groundwater table and the land surface that reduce the flow path. An important conclusion of this study is that the spatial variability of recharge alone, and/or in combination with the spatial variability of topography can substantially alter the behaviors of subsurface flows. This suggests that in macroscale hydrologic models or land surface models, subgrid variations of recharge and topography can make significant contributions to the grid mean subsurface flow and must be accounted for in regions with large surface heterogeneity. This is particularly true for regions with humid climate and relatively shallow groundwater table where the combined impacts of spatial variability of recharge and topography are shown to be more important. For regions with arid climate and relatively deep groundwater table, simpler formulations, especially the power law, for subsurface flow can work well, and the impacts of subgrid variations of recharge and topography may be ignored.

58 GEOSCIENCES↗

Identification and Characterization of Persistent Cold Pool Events from Temperature and Wind Profilers in the Columbia River Basin

Cold pool events occur when deep layers of stable, cold air remain trapped in a valley or basin for multiple days, without mixing out from daytime heating. With large impacts on air quality, freezing events, and es-pecially on wind energy production, they are often poorly forecast by modern mesoscale numerical weather prediction (NWP) models. Understanding the characteristics of cold pools is, therefore, important to provide more accurate forecasts. This study analyzes cold pool characteristics with data collected during the Second Wind Forecast Improvement Project (WFIP2), which took place in the Columbia River basin and Gorge of Oregon and Washington from fall 2015 until spring 2017. A subset of the instrumentation included three microwave radiometer pro?lers, six radar wind pro?lers with radio acoustic sounding systems, and seven sodars, which together provided seven sites with collocated vertical pro?les of temperature, humidity, wind speed, and wind direction. Using these collocated observations, we developed a set of criteria to determine if a cold pool was present based on stability, wind speed, direction, and temporal continuity, and then developed an automated algorithm based on these criteria to identify all cold pool events over the 18 months of the ?eld project. Characteristics of these events are described, including statistics of the wind speed distributions and pro?les, stability conditions, cold pool depths, and descent rates of the cold pool top. The goal of this study is a better understanding of these characteristics and their processes to ultimately lead to improved physical parameterizations in NWP models, and consequently improve forecasts of cold pool events in the study region as well at other locations that experiences similar events.

McCaffrey, Katherine L.↗

Tropical Convective Transition Statistics and Causality in the Water Vapor–Precipitation Relation

Abstract Previous work by various authors has pointed to the role of lower-free-tropospheric humidity in affecting the onset of deep convection in the tropics. Empirical relationships between column water vapor (CWV) and precipitation have been inferred to result from these effects. Evidence from previous work has included deep convective conditional instability calculations for entraining plumes, in which the lower-free-tropospheric environment affects the onset of deep convection due to the differential impact on buoyancy of turbulent entrainment of dry versus moist air. The relationship between deep convection and water vapor is, however, a two-way interaction because convection also moistens the free troposphere. The present study adds an additional line of evidence toward fully establishing the causality of the precipitation–water vapor relationship. Parameter perturbation experiments using the coupled Community Earth System Model (CESM) with high-time-resolution output are analyzed for a set of statistics for the transition to deep convection, coordinated with observational diagnostics for the Green Ocean Amazon (GOAmazon) campaign and tropical western Pacific Atmospheric Radiation Measurement (ARM) sites. For low values of entrainment in the deep convective scheme, these statistics are radically altered and the observed pickup of precipitation with CWV is no longer seen. In addition to helping cement the dominant direction of causality in the fast-time-scale precipitation–CWV relationship, the results point to impacts of entrainment on the climatology. Because at low entrainment convection can fire before tropospheric moistening, the climatological values of relative humidity are lower than observed. These findings can be consequential to biases in simulated climate and to projections of climate change.

54 ENVIRONMENTAL SCIENCES↗