Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solar cell”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,783 records · Page 99
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Detection of hairline cracks in textured silicon solar cells

Using a focused laser scanner, the optical technique described in the present paper can be used to detect hairline cracks of the type occurring in solar cells subjected to surface texturing. The technique is capable of detecting cracks of the order of a few microns, which, otherwise, can be observed only under high magnification using an optical microscope. The technique consists of scanning a solar cell with a finely focused laser beam and recording the photoresponse (short circuit current or open circuit voltage) as a function of beam position. The presence of a crack is manifested by a sharp dip in the photoresponse.

Sopori, B. L.↗
DOE OSTI2021

Combined Precursor Engineering and Grain Anchoring Leading to MA‐Free, Phase‐Pure, and Stable α‐Formamidinium Lead Iodide Perovskites for Efficient Solar Cells

Abstract α‐Formamidinium lead iodide (α‐FAPbI 3 ) is one of the most promising candidate materials for high‐efficiency and thermally stable perovskite solar cells (PSCs) owing to its outstanding optoelectrical properties and high thermal stability. However, achieving a stable form of α‐FAPbI 3 where both the composition and the phase are pure is very challenging. Herein, we report on a combined strategy of precursor engineering and grain anchoring to successfully prepare methylammonium (MA)‐free and phase‐pure stable α‐FAPbI 3 films. The incorporation of volatile FA‐based additives in the precursor solutions completely suppresses the formation of non‐perovskite δ‐FAPbI 3 during film crystallization. Grains of the desired α‐phase are anchored together and stabilized when 4‐ tert ‐butylbenzylammonium iodide is permeated into the α‐FAPbI 3 film interior via grain boundaries. This cooperative scheme leads to a significantly increased efficiency close to 21 % for FAPbI 3 perovskite solar cells. Moreover, the stabilized PSCs exhibit improved thermal stability and maintained ≈90 % of their initial efficiency after storage at 50 °C for over 1600 hours.

Ling, Xufeng↗
DOE OSTI2021

Emerging inorganic solar cell efficiency tables (version 2)

Abstract This paper presents the second version of the efficiency tables of materials considered as emerging inorganic absorbers for photovoltaic solar cell technologies. The materials collected in these tables are selected based on their progress in recent years, and their demonstrated potential as future photovoltaic absorbers. The first part of the paper consists of the guidelines for the inclusion of the different technologies in this paper, the verification means used by the authors, and recommendation for measurement best practices. The second part details the highest world-class certified solar cell efficiencies, and the highest non-certified cases (some independently confirmed). The third part highlights the new entries including the record efficiencies, as well as new materials included in this version of the tables. The final part is dedicated to review a specific aspect of materials research that the authors consider of high relevance for the scientific community. In this version of the efficiency tables, we are including an overview of the latest progress in quasi one-dimensional absorbers, such as antimony chalcogenides, for photovoltaic applications.

14 SOLAR ENERGY↗
DOE OSTI2021

In situ Al 2 O 3 incorporation enhances the efficiency of CuIn(S,Se) 2 solar cells prepared from molecular-ink solutions

Here, we report an efficiency enhancement of solution-processed CuIn(S,Se) 2 (CISSe) thin film solar cells via in situ incorporation of Al 2 O 3 . These films were produced using inks containing CuCl, InCl 3 , AlNO 3 (Al/Al + In: 0.1) and thiourea dissolved in methanol. After spin coating of these solutions in air, samples were subjected to a selenization process. Auger electron spectroscopy depth-profiling analysis showed that Al is evenly distributed throughout the bulk of the film. Transmission electron microscopy revealed that AlNO 3 precursor reacted with oxygen to form nanosized amorphous Al 2 O 3 grains located within the bulk and grain boundaries of CISSe, as well as at both the top and bottom interfaces. Power conversion efficiency (PCE) as high as 11.6% (JS C : 35.8 mA cm –2 , V OC : 518 mV, FF: 62.2%, no anti-reflection coating) was achieved with Al–CISSe solar cell devices integrated with CdS (chemical bath deposition, thickness: 80 nm) and ZnO/ITO bilayers (sputtered, thickness: 300 nm). The average PCE (10.1%, $\langle$J SC $\rangle$: 34.5 mA cm –2 , $\langle$V OC $\rangle$: 491 mV, $\langle$FF$\rangle$: 59.8%) was nearly 4% (absolute) higher than that measured on CISSe baseline cells fabricated from solutions without Al ($\langle$PCE$\rangle$ = 6.4%, $\langle$J SC $\rangle$: 32.8 mA cm –2 , $\langle$V OC $\rangle$: 410 mV, $\langle$FF$\rangle$: 47.3%). This in situ Al 2 O 3 incorporation is speculated to play a role in the enhancement of the VOC and FF of the devices through passivation of defects in CISSe reducing interface and bulk recombination, as evidenced by a reduced defect density and an increased activation energy of the dominant recombination mechanism from capacitance and temperature-dependent VOC measurements, respectively.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Boosting Tin Perovskite Solar Cell Performance via Light-Induced Interface Doping

Continuous breakthroughs have been achieved in the photoelectric conversion efficiency (PCE) of tin-based perovskite solar cells (TPSCs) in recent years. Inspired by performance improvements observed during device storage, we identified beneficial light-induced interface doping (LIID) in the TPSCs. In situ analyses using X-ray photoelectron spectroscopy and ultraviolet photoelectron spectroscopy reveal that ion migration and oxidation at the interface induce beneficial doping effects, enhancing carrier transport and significantly boosting device performance. By implementing specific illumination techniques or maximum power point tracking (MPPT) methods to achieve LIID, we increased the open-circuit voltage while maintaining a high short-circuit current, reaching a PCE of up to 14.91%. Furthermore, this efficiency was sustained at 70% of its maximum value after nearly 900 h of continuous operation. Our study introduces a novel approach to addressing energy band mismatch, paving the way for improved efficiency in tin-based perovskite solar cells.

Sun, Mulin↗
NASA NTRS1985

Solar cell and I.C. aspects of ingot-to-slice mechanical processing

Intensive efforts have been put into the growth of silicon crystals to suit today's solar cell and integrated circuit requirements. Each step of processing the crystal must also receive concentrated attention to preserve the grown-in perfection and to provide a suitable device-ready wafer at reasonable cost. A comparison is made between solar cell and I.C. requirements on the mechanical processing of silicon from ingot to wafer. Specific defects are described that can ruin the slice or can possibly lead to device degradation. These include grinding cracks, saw exit chips, crow's-foot fractures, edge cracks, and handling scratches.

Dyer, L. D.↗
DOE OSTI2021

Direct Deposition of Nonaqueous SnO 2 Dispersion by Blade Coating on Perovskites for the Scalable Fabrication of p–i–n Perovskite Solar Cells

Tin(IV) oxide materials have been extensively used as electron transport materials in n–i–p perovskite solar cells (PSCs) due to their superior optoelectronic properties, low-temperature processability, and high chemical stability. However, solvent incompatibility and processing temperature have limited the direct deposition of fully solution-processed SnO 2 in p–i–n devices. In this study, we overcome this limitation by the functionalization of SnO 2 nanoparticles with acetate through ligand exchange, allowing their dispersion in anhydrous ethanol. The SnO 2 dispersion was deposited on the perovskite absorber by blade coating without damaging the underlying perovskite layer, as determined by X-ray diffraction and scanning electron microscopy. Photoluminescence spectroscopy confirmed effective electron extraction. The champion device shows 14.1% initial power conversion efficiency (PCE) which is unprecedented for a p–i–n device employing solution-phase SnO 2 . Finally, PSCs stored for 40 days in a nitrogen flow box retained an average of 95.8% of the initial PCE.

14 SOLAR ENERGY↗
NASA NTRS1989

Lunar production of solar cells - A near-term product for a lunar industrial facility

Because of the much lower escape velocity, there is a great advantage in manufacture of solar cells for use in space on the moon rather than on earth. Silicon is abundant on the moon, and new refining methods allow it to be reduced and purified without extensive reliance on materials unavailable on the moon. Silicon and amorphous silicon solar cells could be manufactured on the moon for use in space.

Landis, Geoffrey A.↗
NASA NTRS1979

Study of the Effects of Impurities on the Properties of Silicon Materials and Performance of Silicon Solar Cell

Numerical solutions were obtained from the exact one dimensional transmission line circuit model to study the following effects on the terrestrial performance of silicon solar cells: interband Auger recombination; surface recombination at the contact interfaces; enhanced metallic impurity solubility; diffusion profiles; and defect-impurity recombination centers. Thermal recombination parameters of titanium impurity in silicon were estimated from recent experimental data. Based on those parameters, computer model calculations showed that titanium concentration must be kept below 6x10 to the 12th power Ti/cu cm in order to achieve 16% AM1 efficiency in a silicon solar cell of 250 micrometers thick and 1.5 ohm-cm resistivity.

Sah, C. T.↗
NASA NTRS1982

Reduction of solar cell efficiency by edge defects across the back-surface-field junction - A developed perimeter model

Material imperfections, impurity clusters and fabrication defects across the back-surface-field junction can degrade the performance of high-efficiency solar cells. The degradation from defects appearing on the circumference of a solar cell is analyzed using a two-region developed perimeter device model. The width of the defective perimeter region is characterized by the range or the distance-of-influence of the defective edge and this width is about two diffusion lengths. The defective edge is characterized by a surface recombination velocity. Family of theoretical curves and numerical examples are presented to show that significant reduction of open-circuit voltage can occur in high-efficiency cells which are thin compared with the diffusion length. In one example, the degradation is decreased from 135 mV to 75 mV when the cell size is increased from 10 to 100 times the diffusion length in a thin cell whose thickness is 1% of the diffusion length.

Sah, C. T.↗
NASA NTRS1999

Analysis of Direct Solar Illumination on the Backside of Space Station Solar Cells

The International Space Station (ISS) is a complex spacecraft that will take several years to assemble in orbit. During many of the assembly and maintenance procedures, the space station's large solar arrays must he locked, which can significantly reduce power generation. To date, power generation analyses have not included power generation from the backside of the solar cells in a desire to produce a conservative analysis. This paper describes the testing of ISS solar cell backside power generation, analytical modeling and analysis results on an ISS assembly mission.

Delleur, Ann M.↗
DOE OSTI2025

Solar Cell Efficiency Tables (Version 66)

Consolidated tables showing an extensive listing of the highest independently confirmed efficiencies for solar cells and modules are presented. Guidelines for inclusion of results into these tables are outlined, and new entries since January 2025 are reviewed.

14 SOLAR ENERGY↗
DOE OSTI2022

Degradation and Self-Healing in Perovskite Solar Cells

Organic–inorganic halide perovskites are well-known for their unique self-healing ability. In the presence of strong external stimuli, such as light, temperature, and moisture, high-energy defects are created which can be healed by removing the perovskite from the degradation source. Furthermore, this self-healing ability has been showcased in devices with recoverable performance and day-and-night cycling operation to dramatically extend the device lifetime and even mechanical durability. However, to date, the mechanistic details and theory around this captivating trait are sparse and convoluted by the complex nature of perovskites. With a clear understanding of the intrinsic self-healing property, perovskite solar cells with extended lifetimes and durability can be designed to realize the large-scale commercialization of perovskite solar cells. Here, we spotlight the relevant degradation and self-healing literature and then propose design strategies to help conceptualize future research.

14 SOLAR ENERGY↗
DOE OSTI2022

Testing Asoleyo Decorative Solar Cell and Modules: Cooperative Research and Development, CRADA Number CRD-20-16732 (Final Report)

Team Asoleyo is transforming the utilitarian rectangular grid that dominates the visual style of standard solar panels by re-designing solar cells’ silver contact grid using principles of symmetry, rhythm, and line. Our designs use well-established manufacturing equipment, techniques, and materials, achieving similar manufacturing costs but far superior aesthetic effect- without the need for additional layers or occlusion. This project will test new decorative PV Cell front contact designs, individually and interconnected within modules, for their performance characteristics.

14 SOLAR ENERGY↗
NASA NTRS1979

A low-cost solar-cell front contact using trapped silver mesh and electrostatic bonding

A new system to provide a contact with a silver mesh trapped between the cell and an encapsulating glass cover is described. Borosilicate glass is joined to the cell by electrostatic bonding during which the glass is deformed around the silver mesh to form a permanent optically coupled integral bond to the cell. The hermetic seal prevents the silver from oxidizing and destroying the electrical contact formed during the bonding process. It is demonstrated that electrostatic glass/silicon bonds have excellent stability under a variety of accelerated environmental tests. Electrostatic bonds to thin films of AL2O3, Ta2O5, and ZrO2 on glass can be used to make antireflective coatings for solar cells manufactured by this process. Test solar cells were manufactured by electrostatic bonding with good curve fill factors and efficiencies of 10 percent.

Landis, Geoffrey A.↗
DOE OSTI2025

A 2D/3D Heterostructure Perovskite Solar Cell with a Phase‐Pure and Pristine 2D Layer

Abstract Interface engineering plays a critical role in advancing the performance of perovskite solar cells. As such, 2D/3D perovskite heterostructures are of particular interest due to their optoelectrical properties and their further potential improvements. However, for conventional solution‐processed 2D perovskites grown on an underlying 3D perovskite, the reaction stoichiometry is normally unbalanced with excess precursors. Moreover, the formed 2D perovskite is impure, leading to unfavorable energy band alignment at the interface. Here a simple method is presented that solves both issues simultaneously. The 2D formation reaction is taken first to completion, fully consuming excess PbI 2 . Then, isopropanol is utilized to remove excess organic ligands, control the 2D perovskite thickness, and obtain a phase‐pure, n = 2, 2D perovskite. The outcome is a pristine (without residual 2D precursors) and phase‐pure 2D perovskite heterostructure with improved surface passivation and charge carrier extraction compared to the conventional solution process. PSCs incorporating this treatment demonstrate a notable improvement in both stability and power conversion efficiency, with negligible hysteresis, compared to the conventional process.

14 SOLAR ENERGY↗
NASA NTRS1980

Gaalas/Gaas Solar Cell Process Study

Available information on liquid phase, vapor phase (including chemical vapor deposition) and molecular beam epitaxy growth procedures that could be used to fabricate single crystal, heteroface, (AlGa) As/GaAs solar cells, for space applications is summarized. A comparison of the basic cost elements of the epitaxy growth processes shows that the current infinite melt LPE process has the lower cost per cell for an annual production rate of 10,000 cells. The metal organic chemical vapor deposition (MO-CVD) process has the potential for low cost production of solar cells but there is currently a significant uncertainty in process yield, i.e., the fraction of active material in the input gas stream that ends up in the cell. Additional work is needed to optimize and document the process parameters for the MO-CVD process.

Almgren, D. W.↗
NASA NTRS1981

A theory of the n-i-p silicon solar cell

A computer model has been developed, based on an analytical theory of the high base resistivity BSF n(+)(pi)p(+) or p(+)(nu)n(+) silicon solar cell. The model makes very few assumptions and accounts for nonuniform optical generation, generation and recombination in the junction space charge region, and bandgap narrowing in the heavily doped regions. The paper presents calculated results based on this model and compares them to available experimental data. Also discussed is radiation damage in high base resistivity n(+)(pi)p(+) space solar cells.

Goradia, C.↗